Search

In this work, a chemical grafting polymerization method was employed to synthesize EHPMC-g-PANI self-supporting films. Polyaniline (PANI) was grafted onto hydroxypropyl methylcellulose (HPMC) modified with epichlorohydrin (EPHMC) to obtain an EHPMC-g-PANI aqueous dispersion, which was subsequently dried to form the self-supporting films. The introduction of HPMC, with its excellent film-forming ability and mechanical strength, successfully addressed the poor film-forming ability and mechanical properties intrinsic to PANI. Compared to in situ polymerized HPMC/PANI, the EHPMC-g-PANI exhibited significantly improved storage stability. Moreover, the fabricated EHPMC-g-PANI films displayed a more uniform and smoother morphology. The conductivity of all the films ranged from 10−2 to 10−1 S/cm, and their tensile strength reached up to 36.1 MPa. These results demonstrate that the prepared EHPMC-g-PANI holds promising potential for applications in various fields, including conductive paper, sensors, and conductive inks. [ABSTRACT FROM AUTHOR]

Preparing composites from gricultural waste with biodegradable polymers is one of the strategies used to ensure the long-term sustainability of such materials. However, due to the differences in their chemical properties, biomass fillers often exhibit poor interfacial adhesion with polymer matrices. Inspired by mussel foot silk, this work focused on the surface modification of coffee grounds (CGs) using a combination of tannic acid (TA) and alkali treatment. CGs were used as a biomass filler to prepare polybutylene adipate terephthalate (PBAT)/CG composites. The modification of CGs was demonstrated by Fourier transform infrared spectroscopy (FTIR), the water contact angle, and scanning electron microscopy (SEM). The effect of CGs on the rheological, tensile, and thermal properties of the PBAT/CG composites was investigated. The results showed that the addition of CGs increased the complex viscosity, and the surface modification enhanced the matrix–filler adhesion. Compared with unmodified CG composites, the tensile strength and the elongation at break of the composite with TA-modified alkali-treated CGs increased by 47.0% and 53.6%, respectively. Although the addition of CGs slightly decreased the thermal stability of PBAT composites, this did not affect the melting processing of PBAT, which often occurs under 200 °C. This approach could provide a novel method for effectively using biomass waste, such as coffee grounds, as fillers for the preparation of polymer composites. [ABSTRACT FROM AUTHOR]

Ceramifiable silicone rubber (SR) composites with excellent self-supporting properties and ceramifiable properties were prepared by incorporating silicate glass frits (SGFs) and sodium tripolyphosphate (STPP) into the SR. Ceramic residues were obtained by firing ceramifiable SR composites at 700, 850, and 1000 °C for 30 min. The bending angles of the composites were tested for evaluating the self-supporting property. To evaluate the ceramifiable properties of the ceramifiable SR composite, flexural strength, water absorption, and bulk density of its residues were tested. It was found that the addition of STPP improved the shape stability and the self-supporting property of the composites at high temperatures. The flexural strength of the ceramic residue of the composite with STPP firing above 850 °C is more than 5 MPa. X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) analysis showed that the relative content of the crystalline phase was enhanced by about 25% due to the addition of STPP. Furthermore, a possible mechanism for the formation of the crystalline phase was proposed. Scanning elector microscope (SEM) and energy dispersive spectrometry (EDS) analysis demonstrated that with the temperature increase, the inter-infiltration between these melts became easier, which implies that the bulk density of the ceramic residue was improved. [ABSTRACT FROM AUTHOR]

In this study, we fabricated high-performance polyethylene composites by constructing SiO2@silane coupling agent (γ-methylacryloxypropyl trimethoxysilane) and SiO2@polydopamine (PDA) double-layer structures on a magnesium oxysulfate whisker surface. In addition to realizing strong mechanical properties, the flame-retardant properties of the composites were effectively improved. Further increase in the initial crystallization temperature of the modified composites indicated that the dispersion of whisker in the matrix was improved. The drag effect of the modified whisker on the HDPE molecular chain was characterized by dynamic mechanical thermal analysis (DMTA) and the morphology of the impact-fractured surface was characterized by scanning electron microscopy (SEM); both confirmed the improved compatibility between the whisker and the matrix. The tensile strength of HDPE/MOSw@SiO2@KH570 and HDPE/MOSw@SiO2@PDA composites were 22.6% and 41.5% higher than that of the HDPE/MOSw composites, respectively. The impact strengths of the HDPE/MOSw@SiO2@KH570 and HDPE/MOSw@SiO2@PDA composites were 129% and 102% higher than that of the HDPE/MOSw composites, respectively. A stable carbon-silicate layer constructed by a SiO2@KH570 and SiO2@PDA double-layer structure delayed the combustion process. As a result, the limiting oxygen index (LOI) of HDPE/MOSw@SiO2@KH570 and HDPE/MOSw@SiO2@PDA composites increased from 22.5 to 22.9 and 23.5, respectively. [ABSTRACT FROM AUTHOR]

During the laser surface texturing process, scanning overlap is usually misused, because it cannot only be dimple overlap, but also can be laser spot overlap. Experiments were conducted to investigate the relationship between laser spot overlap and dimple overlap during laser surface texturing. Moreover, the effect of dimple overlap on the laser textured microstructures, wettability, and corrosion performances of stainless steel was analyzed. The results have shown that, due to changing radiation conditions, the dimple diameter and dimple overlap varied in a non-linear way with the increase in laser spot overlap. Furthermore, the variation of dimple overlap rather than laser spot overlap had a direct effect on roughness, wettability, and corrosion resistance. When the dimple overlap was greater than 55%, the surface reached the superhydrophobic state and the maximum apparent contact angle was 162.6°. When the dimple overlap was 83.52%, due to passivation layer formed by laser remelting deposition and oxides compaction, corrosion current density was 2.8 × 10−8 A·cm−2, which was 4% of the original value. Consequently, it was determined that it is easier to control the surface roughness, wettability, and corrosion resistance via dimple overlap rather than laser spot overlap in laser surface texturing process. [ABSTRACT FROM AUTHOR]

Ceramifiable ethylene propylene diene monomer (EPDM) composites with fiber network structures were prepared by using aramid fiber (AF), ammonium polyphosphate (APP), and silicate glass frits (SGF). The effect of AF on the curing characteristic of the ceramifiable EPDM composites was studied. The morphology of AF in the composites system was observed by optical microscopy (OM) and scanning electron microscope (SEM). The effects of the observed AF network structures on the solvent resistance, mechanical properties, ablative resistance, self-supporting property, and ceramifiable properties of the composites were investigated. Results suggested that the existence of the AF network structure improved the vulcanization properties, solvent resistance, thermal stability, and ablative resistance of the EPDM composites. An excellent self-supporting property of the EPDM composites was obtained by combining the formation of the AF network and the formation of crystalline phases at higher temperature (above 600 °C). The thermal shrinkage performance of AF and the increased thermal stability of the EPDM composites improved the ceramifiable properties of the EPDM composites. [ABSTRACT FROM AUTHOR]