Search

Negative temperature coefficient (NTC) chip thermistors were thermally coupled to form a novel device (TCCT) aimed for application in microelectronics. It consists of two NTC chip thermistors Th1 and Th2, which are small in size (0603) and power (1/10 W). They are in thermal junction, but concurrently they are electrically isolated. The first thermistor Th1 generates heat as a self-heating component at a constant supply voltage U (input thermistor), while the second thermistor Th2 receives heat as a passive component (output thermistor). The temperature dependence R(T) of NTC chip thermistors was measured in the climatic test chamber, and the exponential factor B10/30 of thermistor resistance was determined. After that, a self–heating current I1 of the input thermistor was measured vs. supply voltage U and ambient temperature Ta as a parameter. Input resistance R1 was determined as a ratio of U and I1 while output thermistor resistance R2 was measured by a multimeter concurrently with the current I1. Temperatures T1 and T2 of both thermistors were determined using the Steinhart–Hart equation. Heat transfer, thermal response, stability, and inaccuracy were analyzed. The application of thermally coupled NTC chip thermistors is expected in microelectronics for the input to output electrical decoupling/thermal coupling of slow changeable signals. [ABSTRACT FROM AUTHOR]

Ablative composites serve as sacrificial materials, protecting underlying materials from high-temperature environments by endothermic reactions. These materials undergo various phenomena, including thermal degradation, pyrolysis, gas generation, char formation, erosion, gas flow, and different modes of heat transfer (such as conduction, convection, and radiation), all stemming from these endothermic reactions. These phenomena synergize to form a protective layer over the underlying materials. Carbon, with its superb mechanical properties and various available forms, is highlighted, alongside phenolics known for good adhesion and fabric ability and elastomers valued for flexibility and resilience. This study focuses on recent advancements in carbon-and-phenolic and carbon-and-elastomeric composites, considering factors such as erosion speed; high-temperature resistance; tensile, bending, and compressive strength; fiber–matrix interaction; and char formation. Various authors' calculations regarding the percentage reduction in linear ablation rate (LAR) and mass ablation rate (MAR) are discussed. These analyses inform potential advancements in the field of carbon/phenolic and carbon/elastomeric ablative composites. [ABSTRACT FROM AUTHOR]

In the European Union, buildings account for 42% of the energy consumption and 36% of the direct and indirect energy-related greenhouse gas emissions. Reducing thermal power for heating purposes is crucial to achieve climate neutrality. The main purpose of this article is to identify the places in the building where it is possible to significantly improve energy efficiency through the use of appropriate construction and material solutions. This article contains a multi-aspect approach to the heat balance of a building. Solutions that have a direct impact on building energy consumption were analysed, taking into account architectural, technological, and material aspects. Particular attention was paid to energy-efficient design and material solutions for non-transparent and transparent external walls and thermal storage walls (Trombe walls). An analysis of heat transfer through building elements was carried out, along with the optimisation of energy-efficient solutions for non-transparent and transparent barriers. Two methods for determining the equivalent heat transfer coefficient Ue for solar active partitions are presented. The analysis presented in the work using the original method of the balanced heat transfer coefficient Ue is a testing ground for identifying unfavourable features of the building structure, as well as the most energy-efficient solutions that can be used in establishing standards for the construction and modernisation of buildings. The value of the Ue coefficient illustrates the actual heat transfer through the partition. Having Ue values for various structural solutions of building envelopes, the designer can easily select the most effective ones. The use of the presented methodology will allow for the optimisation of technical solutions for building elements to improve its energy efficiency. [ABSTRACT FROM AUTHOR]

In this study, we introduced a new type of basis function and subsequently a Chebyshev delta shaped collocation method (CDSC). We then use this method to numerically investigate both the natural convective flow and heat transfer of nanofluids in a vertical rectangular duct on the basis of a Darcy–Brinkman–Forchheimer model and the electroosmosis-modulated Darcy–Forchheimer flow of Casson nanofluid over stretching sheets with Newtonian heating problems. The approximate solution is represented in terms of Chebyshev delta shaped basis functions. Novel error estimates for interpolating polynomials are derived. Computational experiments were carried out to corroborate the theoretical results and to compare the present method with the existing Chebyshev pseudospectral method. To demonstrate our proposed approach, we also compared the numerical solutions with analytic solutions of the Poisson equation. Computer simulations show that the proposed method is computationally cheap, fast, and spectrally accurate and more importantly the obtained approximate solution can easily be used by researchers in this field. [ABSTRACT FROM AUTHOR]

Achieving a quick temperature increase is a burning issue for biophysical applications, like germ inactivation and tumor ablation, and for energy performances, like solar collectors and steam generators. Based on the plasmon resonance phenomenon, noble metallic nanoparticles have emerged as promising weapons due to their very high biocompatibility, optical properties, and high surface-to-volume ratio, increasing energy conversion and allowing the maximum temperature to be reached faster. This work examines the energy conversion in sandwiched glassy platforms with gold nanorods. The platforms are kept vertically in the air and illuminated by a 0.5 W near-infrared laser (808 nm). To describe this aspect theoretically, the size and conversion efficiency of the electromagnetic properties are compromised between the proposed model and the stability of the nanorods. As a research approach, our model of cross-sections and polarizability for the surface effect is proposed, coupled with classical CFD numerical calculations. The results of the proposed model, validated by a thermal camera and spectroscopy measurements, indicate that as long as the energy conversion is visible with relatively low-power lasers (ΔT = 18.5 °C), the platforms do not offer fast heat dissipation. The results indicate that, despite the flow forcing by the air inflow, the entropy generation due to heat conduction is more than three orders higher than the dynamic entropy production. Flow forcing corresponds to the value of the velocity for classical convective motions. Therefore, the delivered heat flux must be distributed via convective transport or the associated high-conductive materials. [ABSTRACT FROM AUTHOR]

Oscillatory baffled flows (OBFs) provide a combined active and passive means of achieving convective heat transfer enhancement, and previous studies at large scale have demonstrated the heat transfer benefits of OBFs. To date, however, this technology has not been scaled down for the purpose of heat sink performance enhancement. Presented in this study is a numerical investigation of a single baffled channel with a hydraulic diameter of 2.8 mm, containing gate baffles, with a 50% open area, which are spaced 7.5 mm apart. Three net-flow rates were investigated while varying the oscillation conditions by varying the oscillation amplitude (3 mm to 7 mm) and by varying the oscillation frequency (0 to 8 Hz). Increasing the oscillation intensity had a greater impact on the Nusselt number compared to simply increasing the net-flow rate, with Nu enhancements of up to 330% observed when imposing oscillatory flow on a purely steady flow. Ideal operating conditions were identified by grouping the data by velocity ratio ( Ψ ) and graphing the theoretical pumping power against the thermal resistance of the channel. The highest Nu enhancement of 330% was achieved for a net-flow Reynolds number ( R e n ) of 165, oscillatory amplitude of 5 mm and a frequency of 8 Hz. Ideal operating conditions can be predicted by selecting conditions with Ψ > 1. A flow with a R e n of 46, Ψ of 7 and Nu = 12 required the same pumping power as a flow with a R e n of 165, Ψ of 0.65 and Nu = 6. [ABSTRACT FROM AUTHOR]

The International Maritime Organization (IMO) is currently rolling out more restrictive regulations in order to achieve net-zero GHG emissions by 2050. In response, the shipping industry is planning to pivot to green energy sources such as hydrogen fuel. However, since hydrogen has an extremely low boiling point (−253 °C), materials for storing liquid hydrogen must be highly resistant to low-temperature brittleness and hydrogen embrittlement. A 316L stainless steel is a typical material that meets these requirements, and various welds have been studied. In this study, 3 pass butt welding was performed by applying the FCAW (flux cored arc welding) process to 10 mm thick ASTM-A240M-316L stainless steel, with the size of the fusion zone and HAZ investigated by mechanical testing and heat transfer FE analysis according to process variables, such as heat input, welding speed, and the number of passes. In all cases, the yield and tensile strengths were about 10% and 3% higher than the base metal, respectively. Furthermore, heat transfer FE analysis showed an average error rate of 1.3% for penetration and 10.5% for width and confirmed the size of the HAZ, which experienced temperatures between 500 °C and 800 °C. [ABSTRACT FROM AUTHOR]

Nowadays, nanotechnology represents a well-established approach, suitable for designing, producing, and applying materials to a broad range of advanced sectors. In this context, the use of well-suited "nano" approaches accounted for a big step forward in conferring optimized flame-retardant features to such a cellulosic textile material as cotton, considering its high ease of flammability, yearly production, and extended use. Being a surface-localized phenomenon, the flammability of cotton can be quite simply and effectively controlled by tailoring its surface through the deposition of nano-objects, capable of slowing down the heat and mass transfer from and to the textile surroundings, which accounts for flame fueling and possibly interacting with the propagating radicals in the gas phase. In this context, the layer-by-layer (LbL) approach has definitively demonstrated its reliability and effectiveness in providing cotton with enhanced flame-retardant features, through the formation of fully inorganic or hybrid organic/inorganic nanostructured assemblies on the fabric surface. Therefore, the present work aims to summarize the current state of the art related to the use of nanostructured LbL architectures for cotton flame retardancy, offering an overview of the latest research outcomes that often highlight the multifunctional character of the deposited assemblies and discussing the current limitations and some perspectives. [ABSTRACT FROM AUTHOR]

This article addresses the design of a compact heat exchanger for the cooling of electronic systems. The Quality Function Deployment (QFD) method is used to identify crucial product features to improve device performance and key customer requirements. The QFD simplifies management processes, allowing modifications to device components, such as design parameters (dimensions and materials) and operating conditions (flow type and preferred temperature range). The study was applied to analyse the fundamental features of a compact heat exchanger, assessing their impact on enhancing heat transfer intensity during fluid flow through mini-channels. The thermal efficiency of the compact heat exchanger was tested experimentally. The results allow to verify the results obtained from the numerical simulations due to Simcenter STAR-CCM+. Consequently, the experimental part was reduced in favour of numerical simulations conducted using this commercial CFD software version 2020.2.1 Build 15.04.01. The numerical simulations performed with the aid of CFD showed increases in the heat transfer coefficient of up to 180% compared to the case treated as a reference. The application of the QFD matrix significantly reduces the time required to develop suitable design and material solutions and determine the operating parameters for the cooling of miniature electronic devices. [ABSTRACT FROM AUTHOR]

Photovoltaic–thermal (PVT) technology is gaining popularity due to the diminishing availability of traditional fossil fuels and escalating environmental concerns. Enhancing the heat dissipation of PVT to improve its electrical and thermal performance remains a significant task. This study simulates the thermodynamic and heat transfer characteristics in multiple novel PVT structures by examining the impact of various factors such as collector materials, radiation intensity, mass flow rate, and inlet temperature. This work also identifies the optimal mass flow rate for locations with different solar radiation. The numerical results indicate that the electrical efficiency of a designed cylindrical structure has increased by 1.73% while the thermal efficiency has increased by 8.29%. Aluminum is identified as the most cost-effective material for the collector. The optimal mass flow rates in selected locations of Xining, Taiyuan, and Turpan are 0.36 kg/s, 0.35 kg/s, and 0.30 kg/s, respectively. The numerical results provide valuable insight into optimizing the design and operating conditions of PVT systems. [ABSTRACT FROM AUTHOR]

Large-eddy simulation (LES) and Reynolds-Averaged Navier–Stokes (RANS) equations were used to study incompressible flow and heat transfer in a U-duct with a high-aspect-ratio trapezoidal cross section. For the LES, the WALE subgrid-scale model was employed, and its inflow boundary condition was provided by a concurrent LES of incompressible fully-developed flow in a straight duct with the same cross section and flow conditions as the U-duct. LES results are presented for turbulent kinetic energy, Reynolds stresses, pressure–strain rate, turbulent diffusion, turbulent transport, and velocity–temperature correlations, with a focus on how they are affected by the U-turn region of the U-duct. The LES results were also used to assess three commonly used RANS models: the realizable k-ε with the two-layer model in the near-wall region, the two-equation shear-stress transport model, and the seven-equation stress-omega Reynolds stress model. Results obtained show steady and unsteady RANS to incorrectly predict the effects of unsteady flow separation. The results obtained also identified the terms in the RANS models that need to be modified and suggested how turbulent diffusion should be modeled when there is unsteady flow separation. [ABSTRACT FROM AUTHOR]

This paper presents an experimental investigation conducted to determine the influence of parameters such as the ambient temperature, pollution level, and substrate material on the formation of dry bands on polluted layers. To investigate these parameters, we applied a simplified insulator geometry, developed in our previous work, to experimentally control the complex process of dry band formation on a polluted surface. The simple geometry of the experimental model enabled the use of Plexiglas, RTV, and glass as construction substrate materials. RTV and glass were used to simulate a composite and ceramic insulator surface, respectively. Moreover, an electrooptic (EO) probe enabled the measurement of the axial E-field evolution at the surface of the dry band during dry band formation. The results indicated that the substrate material, ambient temperature, and pollution level substantially influence dry band formation. The effects of the first two parameters are directly associated with heat transfer phenomena in the substrate material and at the ambient air/substrate interface. The effect of the third parameter is associated with absorption and evaporation of the pollution layer. In addition, the appearance of the dry band can be clearly identified by a rapid increase in both the pollution layer resistance and the axial E-field in the dry band area. The value of the axial E-field is influenced primarily by the width of the dry band and by the pollution layer resistance, which is directly dependent on the humidification duration. Finally, because most of the results obtained herein were in accordance with those in the literature, we conclude that the proposed experimental model may provide an effective and inexpensive testing method for developing new materials and solutions for improving the dielectric performance of insulators used in polluted environments. Similarly, the simple geometry of the experimental model and the ability to easily control the experimental parameters may enable this tool to validate the results of various numerical models in studies of the thermoelectrical behavior of polluted insulators. [ABSTRACT FROM AUTHOR]

The utilization of phase change materials (PCMs) in solar water heating systems (SWHS) has undergone notable advancements, driven by a rising demand for systems delivering superior performance and efficiency. Extensive research suggests that enhancing heat transfer (HTE) in storage systems is crucial for achieving these improvements. This review employs a bibliometric analysis to track the evolution of HTE methods within this field. While current literature underscores the necessity for further exploration into hot water generation applications, several methodologies exhibit significant promise. Particularly, strategies such as fins, encapsulation, and porous media emerge as prominent HTE techniques, alongside nanofluids, which hold the potential for augmenting solar water heating systems. This review also identifies numerous unexplored techniques awaiting investigation, aiming to pave new paths in research and application within the field of hot water generation. It highlights methods that could be used independently or alongside predominantly used techniques. [ABSTRACT FROM AUTHOR]

Plate heat exchangers are widely used in the Heating, Ventilation, and Air Conditioning (HVAC) field. Cross-corrugated triangular ducts are commonly employed in plate heat exchangers. Inserting baffles into the cross-corrugated triangular ducts can improve the heat transfer performance of the plate heat exchangers. This study focuses on intricate interdependencies among the flow channel apex angle, the trapezoidal baffle inclination angle, baffle position, and Reynolds number (Re) on heat transfer and pressure drop using response surface methodology (RSM) and computational fluid dynamic (CFD). To identify the factors that maximize the Nusselt number (Nu) and minimize friction factor (f), the RSM is used to design factors, conduct numerical studies, and establish regression equations. The results show that the apex angle, baffle angle, X-direction position, and Re have significantly affected Nu and f. Compared to a non-baffled channel with the same apex angle and Re conditions, the optimized channel enhances heat transfer by 1.54 times and has an almost identical pressure drop. The inclined baffle significantly enhances comprehensive performance at low Re. The synergistic effect of the heat transfer and pressure drop is most optimal when the apex angle of the flow channel is 90°, the trapezoidal baffle inclination angle is 52.5°, and the Re is 1000, with the baffle position at 0.625H in the X-direction. [ABSTRACT FROM AUTHOR]

Working fluids that incorporate solid microencapsulated phase change materials (MPCMs) can benefit from properties such as density and viscosity, which are crucial for improving heat capacity and transfer. However, limited data are available on these parameters for specific slurry and mass ratios. In this study, we present a comparative analysis of the experimental results on the viscosity of three different MPCM aqueous dispersions, namely MPCM 31-S50, MPCM 25-S50, and Micronal 5428X. Varying MPCM mass ratios of distilled water were used to obtain different mass concentrations of the phase change material (PCM), and the resulting slurries were analysed at temperatures ranging from 15 to 40 °C. Our findings showed that all slurries exhibited non-Newtonian characteristics at low shear rates, with viscosity stabilising at higher shear rates, resulting in the characteristics of a Newtonian fluid. The viscosity results were highly dependent on the type of MPCM base dispersion, particularly at high mass ratios, with the slurries having viscosities higher than those of water. Furthermore, we conducted density experiments as a function of temperature, using a flow test setup and a Coriolis flowmeter (Endress+Hauser, Reinach, Switzerland) to determine the density of two MPCMs, namely MPCM 25-S50 and Micronal 5428X. The test samples were prepared at mass concentrations of 10%, 15%, and 20% of the phase change material. We found significant differences in density and viscosity for different MPCM slurries as a result of both the PCM concentration and the material studied. Our results also revealed an apparent PCM phase change process, in which the slurry density significantly decreased in the temperature range of the phase transition from solid to liquid. [ABSTRACT FROM AUTHOR]

The performance of lithium-ion batteries is greatly influenced by various factors within their operating environment, which can significantly impact their overall efficiency and effectiveness. In this paper, a multi-physics field electrochemical thermal model is established to measure the physical parameters of a battery module during the charge/discharge process. The effects of working temperature, current rate, and convective heat transfer coefficient are investigated by establishing an electrochemical and thermal model. The results are obtained by conducting numerous parameterized scans to analyze the system's state across various operating conditions, enabling the determination of its temperature and the selection of appropriate cooling measures accordingly. Based on the internal and external conditions of battery operation, parameter selection corresponding to the operating range is divided into several stages, with thermal management strategies provided for each stage. The existing framework facilitates the design of battery packs equipped with efficient thermal management strategies, thereby enhancing the battery systems' reliability and performance. Furthermore, it aids in establishing optimal operational and safety boundaries for batteries. [ABSTRACT FROM AUTHOR]

The performance of the Plate Indirect Evaporative Cooler (PIEC) can be effectively improved by incorporating baffles in the dry channel. However, in the dimensional influence of the baffles on PIEC performance there remains a research gap. In order to investigate the impact of baffle dimensions on the wet bulb efficiency, namely the average heat transfer coefficient and the cooling capacity of the PIEC, this paper proposed and verified a three-dimensional numerical model and method based on the species transport model and the Euler wall film model. At the same time, in order to obtain the equilibrium point between the enhanced heat transfer performance and the additional resistance induced by baffles, a comprehensive performance evaluation index is introduced. The results indicate that, under the same conditions, (1) the baffle effect on PIEC performance is significant at a lower inlet air velocity, and the wet bulb efficiency of the PIEC with baffles can be improved by 22.8%; (2) the baffle effect on PIEC performance is negative if its relative length exceeds 60% or the primary air inlet velocity surpasses 4 m/s under the conditions specified in this paper; and (3) the baffle effect on PIEC performance is significant when its channel height is lower and its channel width is larger, and the wet bulb efficiency of the PIEC with baffles can be improved by 29.3%. [ABSTRACT FROM AUTHOR]

This study proposes an anti-gravity 3D pulsating heat pipe (PHP) for cooling pouch batteries in electric vehicles. The 3D PHP envelops the battery cells and rapidly transfers heat generated from the batteries to the bottom cold plate. While the batteries generate heat on their frontal surface during charging and discharging, structural characteristics lead to localized heat accumulation at the electrode lead tabs. Therefore, to address frontal heating, Pattern A with a consistent height for the 3D PHP and Pattern B with varying heights to enhance heat transfer in the localized heating area were designed. The target application involved creating a battery simulator for 340 × 100 mm pouch battery cells, considering the battery's heat generation characteristics. The experiments for the thermal characteristics were conducted, considering factors such as the working fluid (methanol, Novec7100), filling ratio, supplied heat, and orientation. Additionally, to observe internal flow mechanisms, a special experimental apparatus was used, employing transparent fluorine rubber tubes to observe the flow mechanism of the 3D PHP. In the results of the thermal characteristics, the optimal filling ratio was 15% when heat generation levels of 50 W and 100 W were supplied and 20% when 150 W was supplied. The impact of orientation yielded varied results depending on the pattern and working fluid, attributed to the complex interplay of flow momentum due to orientation changes and the influence of the working fluid's buoyancy under anti-gravity conditions. Pattern B, designed with the goal of applying a localized heat model, exhibited relatively decreased heat transfer performance in areas with varying heights. As the distance from the varying height portion increased, temperature oscillations and heat transfer became more active. These results suggest that variations in the shape of the 3D PHP could be a primary design variable for crafting localized heat models. Observations of internal flow revealed that the 3D PHP, with its unique shape and operation under anti-gravity conditions, exhibits longer and more irregular cycles compared to gravity-assist PHPs, transferring heat through rapid oscillations of internal working fluid liquid/vapor slug/plug. The potential of 3D PHPs for cooling electric vehicle batteries is suggested by these findings, and further experimentation is planned to evaluate the optimal design and applicability. [ABSTRACT FROM AUTHOR]

This paper deals with the design of porous geometry of a heat transfer element. The proposed geometry combines a gyroid triply periodic minimal surface with the recursive principle of geometric body creation. The designed geometry is based on an attempt to increase the heat transfer surface while eliminating negative impacts on the fluid characteristics in the form of pressure loss or increase of the friction coefficient. The proposed geometry of the heat transfer element was compared with a pair of geometries based on the basic gyroid shape but with different channel size parameters. A numerical simulation was performed in Ansys Fluent 2020 R1 using the SST k-omega turbulence model for flow velocities in the range of 0.01 m.s−1 to 0.5 m.s−1, which covered a wide range of the Reynolds number and thus also flow forms in terms of the turbulence intensity. The presented results clearly show lower values of pressure loss and friction coefficient of the proposed geometry compared to the evaluated porous structures. Also, at the same time, they describe the factors positively influencing the mixing process of the liquid in the proposed element, which leads to an increase in the efficiency of the heat transfer process. [ABSTRACT FROM AUTHOR]

In the realm of high-tech materials and energy applications, accurately measuring the transient heat flow at media boundaries and the internal thermal conductivity of materials in harsh heat exchange environments poses a significant challenge when using conventional direct measurement methods. Consequently, the study of photothermal parameter reconstruction in translucent media, which relies on indirect measurement techniques, has crucial practical value. Current research on reconstructing photothermal properties within participating media typically focuses on single-objective or time-invariant properties. There is a pressing need to develop effective methods for the simultaneous reconstruction of time-varying thermal flow fields and internal thermal conductivity at the boundaries of participating media. This paper introduces a computational model based on the numerical simulation theory of internal heat transfer systems in participating media, stochastic particle swarm optimization algorithms, and Kalman filter technology. The model aims to enable the simultaneous reconstruction of various thermal parameters within the target medium. Our results demonstrate that under varying levels of measurement noise, the inversion results for different target parameters exhibit slight oscillations around the true values, leading to a reduction in reconstruction accuracy. However, overall, the model demonstrates robustness and accuracy in ideal conditions, validating its effectiveness. [ABSTRACT FROM AUTHOR]

In this paper, we consider the time-fractional Black–Scholes model with deterministic, time-varying coefficients. These time parametric constituents produce a model with greater flexibility that may capture empirical results from financial markets and their time-series datasets. We make use of transformations to reduce the underlying model to the classical heat transfer equation. We show that this transformation procedure is possible for a specific risk-free interest rate and volatility of stock function. Furthermore, we reverse these transformations and apply one-dimensional optimal subalgebras of the infinitesimal symmetry generators to establish invariant solutions. [ABSTRACT FROM AUTHOR]

In this study, three randomly packed beds with varying tube-to-particle diameter ratios (D/d) are constructed using the discrete element method (DEM) and simulated via CFD under low pore Reynolds numbers (Rep < 100). An innovation of this research lies in the application of hydrogen in randomly packed beds, coupled with the consideration of its temperature-dependent thermal properties. The axial analysis of the heat transfer characteristics shows that PB−5 and PB−6 achieve thermal equilibrium 44% and 58% faster than PB−4, respectively, demonstrating enhanced heat transfer efficiency. However, at higher flow rates (0.8 m/s), the large-sized fluid channels in PB−6 severely impact the heat transfer efficiency, slightly reducing it compared to PB−5. Additionally, this study introduces a localized segmentation method for calculating the axial local Nusselt number, showing that the axial local Nusselt number (Nu) not only exhibits an inverse relationship with the axial porosity distribution, but also matches its amplitude fluctuations. The wall effect significantly impacts the flow and temperature distribution in the packed bed, causing notable velocity and temperature oscillations in the near-wall region. In the near-wall region, the average temperature is lower than in the core region, and the axial temperature profile exhibits more intense oscillations. These findings may provide insights into the use of hydrogen in randomly packed beds, which are vital for enhancing industrial applications such as hydrogen storage and utilization. [ABSTRACT FROM AUTHOR]

Controlling heat transfer through components with adjustable thermal resistance can be of great benefit in a wide range of applications such as the thermal management of spacecraft or electric vehicles. A novel concept for both thermal switching and thermal regulation is the use of a water-loaded adsorbent within a reservoir that a regular heat pipe is expanded with. By reversibly desorbing or adsorbing water, states of low and high thermal resistance can be achieved. This concept has been studied so far only in thermosiphons that rely on gravity support. To expand potential application fields, we successfully investigated the utilization of heat pipes with a capillary structure, achieving against-gravity operation. Adsorption-based heat pipe demonstrators were experimentally examined regarding their characteristic properties. Thermal resistances during the on and off state of 0.25 KW−1 and 6.5 KW−1, respectively, were measured, yielding switching ratios of up to 26. Furthermore, the role of the adsorbent reservoir heat exchanger was examined and found to have a significant potential to yield an improvement with regards to dynamic performance. With an improved demonstrator design, the dynamic performance was enhanced as the hysteresis behavior was reduced and a minimum switching time of 5 min was recorded. [ABSTRACT FROM AUTHOR]

This paper presents the results of a study on the non-isothermal laminar flow and heat transfer of oil with Newtonian and viscoplastic rheologies. Heat exchange with the surrounding environment leads to the formation of a near-wall zone of viscoplastic fluid. As the flow proceeds, the transformation of a Newtonian fluid to a viscoplastic state occurs. The rheology of the Shvedoff–Bingham fluid as a function of temperature is represented by the effective molecular viscosity apparatus. A numerical solution to the system of equations of motion and heat transfer was obtained using the Semi-Implicit Method for Pressure-Linked Equations (SIMPLE) algorithm. The calculated data are obtained at Reynolds number Re from 523 to 1046, Bingham number Bn from 8.51 to 411.16, and Prandl number Pr = 45. The calculations' novelty lies in the appearance of a "stagnation zone" in the near-wall zone and the pipe cross-section narrowing. The near-wall "stagnation zone" is along the pipe's radius from r/R = 0.475 to r/R = 1 at Re = 523, Bn = 411.16, Pr = 45, u1 = 0.10 m/s, t1 = 25 °C, and tw = 0 °C. The influence of the heat of phase transition of paraffinic oil on the development of flow and heat transfer characteristics along the pipe length is demonstrated. [ABSTRACT FROM AUTHOR]

Ice plug technology is an effective method for isolating the pipeline system, which are promising methods utilized in the nuclear, chemical, and power industries. To reduce the cold energy consumption and temperature stress, the multi-stage (1–10) of time-dependent thermal boundary conditions was proposed for the formation of ice plug, while the gradient cooling wall temperature of multi-stage was applied. A numerical model considering the liquid–solid phase change, heat transfer, and time-dependent thermal boundary condition has been established. The effects of the ratio of length and diameter of the cooling wall lc/d (1–9) on the formation rate and heat flux of ice plug in the pipe has been investigated. The fastest formation rate of ice plug with 800 mm in the axial direction (7.47 cm3/s) was observed in the pipe with the lc/d of 5. The formation rate of ice plug and the ice formation volume under unit energy consumption VE under various stages (1–10) of cooling wall temperature have been compared. The VE of eight temperature stages (1.45 cm3/kJ) was 1.16 times than the VE of one temperature stage, which satisfied the freezing rate at the same time. This investigation provides insight for proposing an energy-saving system for the formation of ice plug. [ABSTRACT FROM AUTHOR]

Wind machines based on the air disturbance method are progressively employed to mitigate frost damage within the agricultural machinery frost protection. These devices are utilized during radiative frost nights to disrupt near-surface thermal inversion through air mixing. Despite this application, the fundamental mechanisms underlying these mixing processes are not well comprehended. In this research, numerical simulations were conducted using COMSOL Multiphysics software version 6.0 to simulate the flow and heat transfer processes between the thermal airflow and both the tea canopy and stems. The results indicated that due to obstruction from the canopy cross-section, the airflow velocity on the contact surface rapidly increased. As the airflow further progressed, the high-speed region of the airflow gradually approached the canopy surface. Turbulent kinetic energy increased initially on the windward side of the canopy cross-section and near the top interface. On the windward side of the canopy, due to the initial impact of the thermal airflow, rapid heating occurred, resulting in a noticeable temperature difference between the windward and leeward sides within a short period. In the interaction between airflow and stems, with increasing airflow velocity, fluctuations and the shedding of wake occurred on the leeward side of the stems. The maximum sensible heat flux at the windward vertex of the stem increased significantly with airflow velocity. At an airflow velocity of 2.0 m/s, the maximum heat flux value was 2.37 times that of an airflow velocity of 1.0 m/s. This research utilized simulation methods to study the interaction between airflow and tea canopy and stems in frost protection, laying the foundation for further research on the energy distribution in tea ecosystem under the disturbance of airflow for frost protection. [ABSTRACT FROM AUTHOR]

Cyperus esculentus is a hard-to-control, destructive perennial weed propagating and spreading through rhizomes and tubers. Currently, a combination of mechanical, cultural, and chemical measures sustained over time is required for satisfactory control of arable crops. Hood steaming is a promising thermal technique for rapid depletion of the soil tuber bank. The effect of hood steaming on C. esculentus tuber vitality was investigated using a dose–response experiment on two localities in Belgium. Steaming was performed for five durations (2, 4, 8, 16, and 32 min). Moreover, the effects of tuber burial depth (5, 15, and 25 cm), genetic C. esculentus clone (three different clones), and pedohydrological parameters (sandy and sandy, loamy soil) on hood steaming efficacy were determined. Additionally, the heat sensitivity of genetically diverse C. esculentus tubers was investigated in a laboratory incubator experiment in which incubation temperature and duration varied. To control tubers at depths of 5, 15, and 25 cm, treatment durations of 8, 16, and 32 min were required, respectively. In general, clones producing large tubers showed lower heat sensitivity. As pedohydrological parameters may affect heat transfer into the soil, they may affect steaming efficacy as well. To obtain complete control of C. esculentus tubers, soil temperature should be 50 °C or more for at least 42 min. Hood steaming is a highly suitable alternative technique for a rapid and strong depletion of the soil tuber bank in small well-delineated C. esculentus patches. [ABSTRACT FROM AUTHOR]

Hot-gas drum heating (HDH) of bituminous mixtures is a new approach to heating bituminous mixtures that is influenced by the parameters of the hot gas and drum. A fluid thermal numerical model was developed to evaluate the effects of heating bituminous mixtures with HDH using a finite-volume method (FVM). The FVM was verified through the heating test of a bituminous mixture. The effects of the drum rotating speed and hot-gas speed on the efficiency of heating the bituminous mixture during HDH were analyzed using Fluent. The results indicated that the drum rotating speed directly influenced the formation of a bituminous-mixture curtain, which had a significant effect on the efficiency of heating the bituminous mixture. The efficiency of the heat exchange between the hot gas and the bituminous mixture was high, with full contact between the hot gas and the bituminous mixture. With an increase in the hot-gas speed, the heating time became shorter; however, the rate of hot-gas utilization was reduced. A symmetrical temperature distribution and a superior heating efficiency of the bituminous mixture were achieved when the drum rotating speed was 7 rpm and the hot-gas speed was 1.4 m/s. [ABSTRACT FROM AUTHOR]

This paper presents a topology optimization (TopO) method for conjugate heat transfer (CHT), with turbulent flows. Topological changes are controlled by an artificial material distribution field (design variables), defined at the cells of a background grid and used to distinguish a fluid from a solid material. To effectively solve the CHT problem, it is crucial to impose exact boundary conditions at the computed fluid–solid interface (FSI); this is the purpose of introducing the cut-cell method. On the grid, including also cut cells, the incompressible Navier–Stokes equations, coupled with the Spalart–Allmaras turbulence model with wall functions, and the temperature equation are solved. The continuous adjoint method computes the derivatives of the objective function(s) and constraints with respect to the material distribution field, starting from the computation of derivatives with respect to the positions of nodes on the FSI and then applying the chain rule of differentiation. In this work, the continuous adjoint PDEs are discretized using schemes that are consistent with the primal discretization, and this will be referred to as the "Think Discrete–Do Continuous" (TDDC) adjoint. The accuracy of the gradient computed by the TDDC adjoint is verified and the proposed method is assessed in the optimization of two 2D cases, both in turbulent flow conditions. The performance of the TopO designs is investigated in terms of the number of required refinement steps per optimization cycle, the Reynolds number of the flow, and the maximum allowed power dissipation. To illustrate the benefits of the proposed method, the first case is also optimized using a density-based TopO that imposes Brinkman penalization terms in solid areas, and comparisons are made. [ABSTRACT FROM AUTHOR]

Compared to sensible heat storage, latent heat storage provides higher energy density due to the enthalpy difference of the storage medium undergoing a phase change. However, the heat storage capability of phase change materials is opposed by low thermal conductivity. To enable sufficient heat transfer within a latent heat storage unit, phase change materials can be used in combination with a metallic matrix. One approach is the infiltration of phase change materials into additively manufactured metallic lattice structures. In this work, the fabrication of aluminum lattice structures through laser powder bed fusion is described. During fabrication, the cell size and the strut diameter were varied to obtain specimens of different geometries. To obtain the thermal conductivity of the fabricated lattices, measurements were conducted based on the transient plane source method. Additionally, finite element simulations were carried out to evaluate the effect of fabrication and measurement uncertainties. The thermal conductivity of the fabricated lattices was found to be between 3 W/(m·K) and 130 W/(m·K). The numerically and analytically performed calculations provide good estimations of the experimentally obtained data. [ABSTRACT FROM AUTHOR]

The market for smart greenhouses has been valued at USD 1.77 billion in 2022 and is expected to grow to 3.39 billion by 2030. In order to make this more efficient, with the help of Internet of Things (IoT) technology, it is desired to eliminate the problem of traditional agriculture, which has poor monitoring and accuracy control of the parameters of a culture. Climate control decisions in a greenhouse are made based on parameter monitoring systems, which can be remotely controlled. Instead of this adjustment of the measured parameters, it would be preferable from the point of view of energy consumption that they should be calculated at optimal values from the design phase of the greenhouse. For this reason, it would be better to perform an energy simulation of the greenhouse first. For the study carried out in this work, a small greenhouse (mini-greenhouse) was built. It was equipped with an IoT sensor system, which measured indoor climate parameters and could send data to the cloud for future recording and processing. A simplified mathematical model of the heat balance was established, and the measured internal parameters of the mini-greenhouse were compared with those obtained from the simulation. After validating the mathematical model of the mini-greenhouse, this paper aimed to find the optimal position for placing a normal-sized greenhouse. For this, several possible locations and orientations of the greenhouse were compared by running the mathematical model, with which the most unfavorable positions could be eliminated. Then, some considerably cheaper "mini-greenhouses" were made and placed in the locations with the desired orientations. Using sensor systems and technologies similar to those presented in this work, the parameters from all mini-greenhouses can be monitored in real time. This real-time monitoring allows for the simultaneous analysis of all greenhouses, without the disadvantages of data collection directly in the field, with all data being recorded in the cloud and other IoT-specific advantages being made use of. In the end, we can choose the optimal solution for the location of a real-size greenhouse. [ABSTRACT FROM AUTHOR]

This article presents a new thermoelastic model that incorporates fractional-order derivatives of two-phase heat transfer as well as a two-temperature concept. The objective of this model is to improve comprehension and forecasting of heat transport processes in two-phase-lag systems by employing fractional calculus. This model suggests a new generalized fractional derivative that can make different kinds of singular and non-singular fractional derivatives, depending on the kernels that are used. The non-singular kernels of the normalized sinc function and the Rabotnov fractional–exponential function are used to create the two new fractional derivatives. The thermoelastic responses of a solid cylinder with a restricted surface and exposed to a moving heat flux were examined in order to assess the correctness of the suggested model. It was considered that the cylinder's thermal characteristics are dependent on the linear temperature change and that it is submerged in a continuous magnetic field. To solve the set of equations controlling the suggested issue, Laplace transforms were used. In addition to the reliance of thermal characteristics on temperature change, the influence of derivatives and fractional order was also studied by providing numerical values for the temperature, displacement, and stress components. This study found that the speed of the heat source and variable properties significantly impact the behavior of the variables under investigation. Meanwhile, the fractional parameter has a slight effect on non-dimensional temperature changes but plays a crucial role in altering the peak value of non-dimensional displacement and pressure. [ABSTRACT FROM AUTHOR]

With the growing demand for photovoltaic (PV) systems as a source of energy generation that produces no greenhouse gas emissions, effective strategies are needed to address the inherent inefficiencies of PV systems. These systems typically absorb only approximately 15% of solar energy and experience performance degradation due to temperature increases during operation. To address these issues, PV–thermal (PVT) technology, which combines PV with a thermal absorber to dissipate excess heat and convert it into additional thermal energy, is being rapidly developed. This review presents an overview of various PVT technologies designed to prevent overheating in operational systems and to enhance heat transfer from the solar cells to the absorber. The methods explored include innovative absorber designs that focus on increasing the heat transfer contact surface, using mini/microchannels for improved heat transfer contiguity, and substituting traditional metal materials with polymers to reduce construction costs while utilizing polymer flexibility. The review also discusses incorporating phase change materials for latent heat absorption and using nanofluids as coolant mediums, which offer higher thermal conductivity than pure water. This review highlights significant observations and challenges associated with absorber design, mini/microchannels, polymer materials, phase change materials, and nanofluids in terms of PV waste heat dissipation. It includes a summary of relevant numerical and experimental studies to facilitate comparisons of each development approach. [ABSTRACT FROM AUTHOR]

Interconnected microchannels (IMCs) in flow boiling have the advantages of optimized heat transfer performance, energy savings and high efficiency, compact size, and strong customizability. They provide new solutions for thermal management and heat transfer at the microscale and have broad application prospects. To further investigate the effect of microchannels with different numbers of transverse sections on the flow boiling heat transfer, we performed numerical simulations on a rectangular microchannel (RMC) and IMCs with 3, 5, and 7 transverse microchannels at high and low mass flux. It was found that fluid experiences similar bubble and slug flow in different numbers of IMCs and the RMC at low mass flux. At a heat flux of q = 90 W/cm2, the downstream regions of the IMCs produce vapor films that span the channels, obstructing the cross-section and weakening the flow exchange between the channels, which lead the heat transfer performance factor of IMC-3, reaching 148.43%, 110.04%, and 116.92% of the RMC, IMC-5, and IMC-7. Under high-quality flux, as the heat flux increases, the heat transfer coefficient increases and the pressure drop decreases due to the existence of lateral microchannels introduced in the interconnected microchannels. Whether at high or low mass flux, structural reasons pertaining to the RMC can easily lead to the accumulation of bubbles and the occurrence of slugs, and the flow boiling instability increases with the increase of heat flux, which leads to a pressure drop and heat transfer performance generally lower than that of IMCs under the same conditions. At q = 120 W/cm2, IMC-7 showed the best heat transfer enhancement. Its heat transfer performance factor was 129.37%, 120.594% and 107.98% of the RMC, IMC-3, and IMC-5, respectively. This article provides theoretical support for the design of interconnected microchannels in thermal management. [ABSTRACT FROM AUTHOR]

The engineering of tubes with surface corrugations is recognized as an effective method for enhancing heat transfer within the tube. Yet the impact of surface corrugation on the flow and heat transfer around the tube's exterior remains inadequately explored. This study investigates the crossflow and heat transfer characteristics in banks of periodically inward-corrugated tubes using computational fluid dynamics. Numerical simulations were performed for both in-line and staggered tube arrangements, covering Reynolds numbers from 1000 to 10,000. The aim was to examine how various corrugation parameters affect heat transfer and flow dynamics in tube banks configured in both in-line and staggered layouts. The results show that the heat transfer and the pressure drop in crossflow across tube banks are substantially influenced by changes in corrugation parameters. Specifically, in the in-line arrangement, both the Nusselt number and Euler number decrease significantly as the corrugation height increases. In contrast, in the staggered arrangement, the Nusselt number and Euler number exhibit less variation in response to surface corrugation. A comparative analysis of performance criteria suggests that a staggered arrangement is more advantageous for improving thermal–hydraulic efficiency in crossflow through corrugated tube banks. [ABSTRACT FROM AUTHOR]

This work numerically studied the heat transfer and flow characteristics of supercritical R134a in horizontal pipes equipped with DDIR, considering variations in the rotation angle of DDIR. The aim is to improve the effects of the DDIR configuration on the heat transfer of supercritical flow. After validation with experimental data, the AKN model was employed to examine the effects of four sets of rotation angles (0°, 30°, 45°, and 60°) on the axial and circumferential heat transfer characteristics of DDIR horizontal tubes under the influence of strong (q1/G1 = 0.1 kJ/kg) and medium (q2/G2 = 0.056 kJ/kg) buoyancy. Results show that variations in the rotation angle do not induce significant alterations in the flow field, thus exerting minimal influence on the axial heat transfer characteristics. Meanwhile, the rotation angle determines the relative positioning of the circumferential inner wall temperatures and heat flux distribution, although the magnitude of this effect remains inconspicuous. The rotational angle parameter can be reasonably neglected in the future design and installation of heat exchangers. [ABSTRACT FROM AUTHOR]

A CFD simulation of the condensation flow of R600a and R290 within microchannels was conducted to explore the effect of mass flux, hydraulic diameter, and vapour quality on heat transfer rate and pressure drop. Data obtained from CFD simulations were used to develop new heat transfer and pressure drop correlations for the condensation flows of R600a and R290, which are climate-friendly refrigerants. Steady-state numerical simulations of condensation flow of refrigerants were carried out inside a single circular microchannel with diameters varying between 0.2 and 0.6 mm. The volume of fluid approach was used in the proposed model, calculating the interface phase change using the Lee model. The CFD simulation model was validated via a comparison of the simulation results with the experimental data available in the literature. It is found that the newly developed Nu number correlation shows a deviation, with an Ave-MAE of 11.16%, compared to those obtained by CFD simulation. Similarly, the deviation between friction factors obtained by the newly proposed correlation and those obtained by CFD simulation is 20.81% Ave-MAE. Widely recognized correlations that are applicable to the condensation of refrigerants within small-scale channels were also evaluated by comparing newly developed correlations. It is concluded that the newly proposed correlation has a higher accuracy in predicting the heat transfer coefficient and pressure drop. This situation can contribute to the creation of a sustainable system via the use of microchannels and climate-friendly refrigerants, like R600a and R290. [ABSTRACT FROM AUTHOR]

Natural convection heat transfer from an inclined array of square cross-section cylinders is experimentally studied. Three cylinders of side length D = 0.02 m and 1 m length are used to form the inclined array. Three-cylinder axis inclination angles to the horizontal of 30°, 45°, and 60° are considered. The cylinders are heated using an internal heating element of constant heat flux. Surface temperatures are measured along the three surfaces of each cylinder; upper, lower, and the front side at nine points spaced evenly by 10 cm. The local circumference average temperature is obtained at each point. Four center-to-center distances to side length S/D = 1.25, 1.75, 2.25, and 2.75 are used. Local Nusselt numbers and the modified Rayleigh numbers are obtained for each cylinder at each circumference averaged temperature point. Results show that the lower cylinder heat transfer is least affected by the array compared to that of its single one followed by the middle and the upper cylinder for all S/D and the inclination angles used. The Nusselt number is degraded from that of the single cylinder at a small S/D and that degradation decreases as the S/D increases for all angles. It is observed that the Nusselt number enhances at the small cylinder axis tilt angle of 30°, followed by 45°, and 60°, especially at high modified Rayleigh numbers. New novel general empirical correlations for Nusselt numbers are obtained for each S/D using the cylinder axis tilt angle, the modified Rayleigh numbers, and the cylinder number in the array as parameters. A new general correlation is obtained for the array using the modified Rayleigh number, S/D, the cylinder axis tilt angle, and the cylinder sequential order number as parameters. These new correlations will help any engineering applications using such a configuration of the array. [ABSTRACT FROM AUTHOR]

The mass loss mechanisms of an aqueous film-forming foam (AF foam), an AR/AFFF water-soluble film-forming foam extinguishing agent (AR foam), and a Class A foam extinguishing agent (A foam) at different levels of thermal radiation, thermal convection, and heat conduction intensity were studied. At a relatively low thermal radiation intensity, the liquid separation rate of the AF, AR, and A foams is related to the properties of the foam itself, such as viscosity and surface/interface tension, which are relatively independent of the external radiation heat flux of the foam. At low radiation intensity (15 kW/m2 and 25 kW/m2), the liquid separation rate of the AF and A foams is relatively stable. When the heat flux intensity is 35 kW/m2, the liquid separation rate of the AF and A foams increases notably, which may be mainly due to the rapid decrease in foam viscosity. And the mass loss behavior is dominated by liquid separation in the AF, AR, and A foams under the influence of thermal radiation and thermal convection. Under the same experimental conditions, the liquid separation rate of AF is the fastest. There is no significant difference in the evaporation rates of the three kinds of foam in the same heat conduction condition. In addition, the AR and A foams usually have a 25% longer liquid separation time (t) under thermal radiation and thermal convection, and the thermal stability is better than AF foam. The temperature reached by the AF foam layer under thermal convection was lower than that of the AR and A foams, and the time for the foam layer to reach the highest temperature under heat conduction was longer than that of the AR and A foams. [ABSTRACT FROM AUTHOR]

The primary concerns for individuals using lithium-ion batteries (LIBs) are aging and thermal runaway (TR). This paper focuses on the thermal runaway propagation (TRP) of cycling aged LIB modules. The impacts of state of charge (SOC), state of health, and cyclic aging temperature on TRP in LIB modules are investigated. The analysis includes parameters such as temperature, voltage, and mass of the modules during TRP. It was found that as SOC increases, the maximum increase in temperature and maximum temperature rate of the modules increased, as did the total mass loss and smoke emissions. The average heat transfer between adjacent cells was higher for the lower SOC. Cycle aging reduces the thermal stability of LIBs, leading to a lower maximum temperature and maximum temperature rate, as well as a larger mass loss compared with fresh battery modules. Regarding aging temperature, low-temperature aging reduces the total duration of TRP compared with room temperature, but it increases the maximum temperature rate and causes greater mass loss. Aging also increases the average heat transfer between adjacent cells. [ABSTRACT FROM AUTHOR]

In semi-transparent polymers, ignition is not only dependent on conductive thermal transfer into the material but also on in-depth absorption of the radiation. The aim of this work was to investigate the influence of bubbling on the thermo-physical and thermo-radiative properties of PMMA and how it may affect its ignition. PMMA plates of varying thickness were exposed to the heat flux of two radiative sources with different emission spectra. Exposure was stopped after different periods of time to study bubbling kinetics and bubble size distribution by optical microscopy. Front and back surface temperatures of samples were recorded during heat exposure. The results indicate that the bubble size distribution is closely related to the temperature gradient within the sample. Steep thermal gradients lead to small-sized bubbles underneath the exposed surface, while weak thermal gradients generate a wider size distribution with in-depth bubbling. All thermo-physical quantities k , ρ and C p were shown to decrease with increasing bubbling degree. Likewise, it was highlighted that bubbling modifies the thermo-radiative properties of PMMA, especially in the near-infrared range. Transmittance decreases while absorbance increases with a bubbling degree. The increase in the absorption coefficient was attributed to multiple scattering by bubbles that expand the pathway of radiation into the materials. It was concluded that changes in both the thermo-physical and thermo-radiative properties with bubbling were likely to account for the delay in ignition observed when using the near-infrared heating source. [ABSTRACT FROM AUTHOR]

The flow and heat transfer of a steady, viscous biomagnetic fluid containing magnetic particles caused by the swirling and stretching motion of a three-dimensional cylinder has been investigated numerically in this study. Because fluid and particle rotation are different, a magnetic field is applied in both radial and tangential directions to counteract the effects of rotational viscosity in the flow domain. Partial differential equations are used to represent the governing three-dimensional modeled equations. With the aid of customary similarity transformations, this system of partial differential equations is transformed into a set of ordinary differential equations. They are then numerically resolved utilizing a common finite differences technique that includes iterative processing and the manipulation of tridiagonal matrices. Graphs are used to depict the physical effects of imperative parameters on the swirling velocity, temperature distributions, skin friction coefficient, and the rate of heat transfer. For higher values of the ferromagnetic interaction parameter, it is discovered that the axial velocity increases, whereas temperature and tangential velocity drop. With rising levels of the ferromagnetic interaction parameter, the size of the axial skin friction coefficient and the rate of heat transfer are both accelerated. In some limited circumstances, a comparison with previously published work is also handled and found to be acceptably accurate. [ABSTRACT FROM AUTHOR]

Due to environmental concerns, natural refrigerants and their use in refrigeration and air conditioning systems are receiving more attention from manufacturers, end users and the scientific community. The study of heat transfer and pressure drop is essential for accurate design and more energy efficient cycles using natural refrigerants. The aim of this work is to provide an overview of the latest outcomes related to heat transfer and pressure drop correlations for ammonia, propane, isobutane and propylene and to investigate the current state of the art in terms of operating conditions. Available data on the existing correlations between heat transfer coefficients and pressure drops for natural refrigerants have been collected through a systematic search. Whenever possible, validity intervals are given for each correlation, and the error is quantified. It is the intention of the authors that this paper be a valuable support for researchers and an aid to design, with particular reference to heat pumps. A procedure based on the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) statement was adopted, and the Scopus database was used to query the relevant literature. A total of 135 publications qualified for inclusion in the survey; 34 articles report experimental investigations for unusual geometric conditions. Of the 101 selected papers related to usual geometric conditions, N = 50 deal only with HTC, N = 16 deal only with pressure drop and the remainder (N = 35) analyse both HTC and pressure drop. Among the 85 HTC papers, N = 53 deal with the evaporating condition, N = 30 with condensation and only N = 2 with the heat transfer correlations under both conditions. Most of the 101 articles concern propane and isobutane. The high temperatures are less widely investigated. [ABSTRACT FROM AUTHOR]

This present review explores the application of artificial intelligence (AI) methods in analysing the prediction of thermophysical properties of nanofluids. Nanofluids, colloidal solutions comprising nanoparticles dispersed in various base fluids, have received significant attention for their enhanced thermal properties and broad application in industries ranging from electronics cooling to renewable energy systems. In particular, nanofluids' complexity and non-linear behaviour necessitate advanced predictive models in heat transfer applications. The AI techniques, which include genetic algorithms (GAs) and machine learning (ML) methods, have emerged as powerful tools to address these challenges and offer novel alternatives to traditional mathematical and physical models. Artificial Neural Networks (ANNs) and other AI algorithms are highlighted for their capacity to process large datasets and identify intricate patterns, thereby proving effective in predicting nanofluid thermophysical properties (e.g., thermal conductivity and specific heat capacity). This review paper presents a comprehensive overview of various published studies devoted to the thermal behaviour of nanofluids, where AI methods (like ANNs, support vector regression (SVR), and genetic algorithms) are employed to enhance the accuracy of predictions of their thermophysical properties. The reviewed works conclusively demonstrate the superiority of AI models over the classical approaches, emphasizing the role of AI in advancing research for nanofluids used in heat transfer applications. [ABSTRACT FROM AUTHOR]

The two-phase ejector is a simple and compact pressure boosting device and widely used in ejector steam-generator water feeding systems and core emergency cooling systems. The direct contact condensation of water and steam is the key process of a two-phase ejector. Usually, the high-temperature and high-pressure steam will inevitably induce non-condensable gases. The existence of non-condensable gases will reduce the condensation heat transfer rate between steam and water, and harm the equipment. This study carried out 3D numerical simulations of a two-phase ejector based on an inhomogeneous multiphase model. The steam inlet pressure and the non-condensable gas mass fraction rang in 0.6–2.9 MPa and 1–10%, respectively. The heat and mass transfer characteristics were analyzed under different conditions. The results show that the heat transfer coefficient and plume penetration length increased with the steam inlet pressure. Non-condensable gas prevents direct contact condensation between the steam and water. The non-condensable gas mass fraction rises from 1% to 10%, the heat transfer between steam and water deteriorates, and leads to a lower heat transfer coefficient. [ABSTRACT FROM AUTHOR]

An open-cell metal foam has excellent characteristics such as low density, high porosity, high specific surface area, high thermal conductivity, and low mass due to its unique internal three-dimensional network structure. It has gradually become a new material for enhanced heat transfer in industrial equipment, new compact heat exchangers, microelectronic device cooling, etc. This research established a comprehensive three-dimensional structural model of open-cell metal foams utilizing Laguerre–Voronoi tessellations and employed computational fluid dynamics to investigate its flow dynamics and coupled heat transfer performance. By exploring the impact of foam microstructure on flow resistance and heat transfer characteristics, the study provided insights into the overall convective heat transfer performance across a range of foam configurations with varying pore densities and porosities. The findings revealed a direct correlation between convective heat transfer coefficient (h) and pressure drop (ΔP) with increasing Reynolds number (Re), accompanied by notable changes in fluid turbulence kinetic energy (e) and temperature (T), ultimately influencing heat transfer efficiency. Furthermore, the analysis demonstrated that alterations in porosity (ε) and pore density significantly affected unit pressure drop (ΔP/L) and convective heat transfer coefficient (h). This study identified an optimal configuration, highlighting a metal foam with a pore density of 20 PPI and a porosity of 95% as exhibiting superior overall convective heat transfer performance. [ABSTRACT FROM AUTHOR]

The thermal conductivity of recently produced hexagonal boron nitride (hBN)-containing nanofluids is comparatively higher than their viscosity, indicating that these materials belong to a relatively novel class. In this study, hBN–water nanofluids in stable and dispersed concentrations were used in parallel and counterflow experiments at volumes of 0.01%, 0.1%, and 1%, as well as at various flow rates and Reynolds numbers. When employing hBN–water nanofluid in a counter-flow heat exchanger instead of distilled water, the results showed a 16.7% increase in the overall heat transfer coefficient. The findings also showed that, in comparison to a counter-flow heat exchanger, employing hBN nanofluid as the cold fluid in a parallel-flow heat exchanger produced superior results in terms of an increase in heat transfer. The effects of nanofluid concentration on pressure drops were investigated through experiments conducted in both parallel- and counter-flow conditions. [ABSTRACT FROM AUTHOR]

Microscale electronics have become increasingly more powerful, requiring more efficient cooling systems to manage the higher thermal loads. To meet this need, current research has been focused on overcoming the inefficiencies present in typical thermal management systems due to low Reynolds numbers within microchannels and poor physical properties of the working fluids. For the first time, this research investigated the effects of a connector with helical geometry on the heat transfer coefficient at low Reynolds numbers. The introduction of a helical connector at the inlet of a microchannel has been experimentally tested and results have shown that this approach to flow augmentation has a great potential to increase the heat transfer capabilities of the working fluid, even at low Reynolds numbers. In general, a helical connector can act as a stabilizer or a mixer, based on the characteristics of the connector for the given conditions. When the helical connector acts as a mixer, secondary flows develop that increase the random motion of molecules and possible nanoparticles, leading to an enhancement in the heat transfer coefficient in the microchannel. Otherwise, the heat transfer coefficient decreases. It is widely known that introducing nanoparticles into the working fluids has the potential to increase the thermal conductivity of the base fluid, positively impacting the heat transfer coefficient; however, viscosity also tends to increase, reducing the random motion of molecules and ultimately reducing the heat transfer capabilities of the working fluid. Therefore, optimizing the effects of nanoparticles characteristics while reducing viscous effects is essential. In this study, deionized water and deionized water–diamond nanofluid at 0.1 wt% were tested in a two-microchannel system fitted with a helical connector in between. It was found that the helical connector can make a great heat transfer coefficient enhancement in low Reynolds numbers when characteristics of geometry are optimized for given conditions. [ABSTRACT FROM AUTHOR]

The freedom of additive manufacturing allows for the production of heat-transferring structures that are optimized in terms of heat transfer and pressure loss using various optimization methods. One question is whether the structural optimizations made can be reproduced by additive manufacturing and whether the adaptations can also be verified experimentally. In this article, adjoint optimization is used to optimize a reference structure and then examine the optimization results experimentally. For this purpose, optimizations are carried out on a 2D model as well as a 3D model. The material chosen for the 3D optimization is stainless steel. Depending on the weighting pairing of heat transfer and pressure loss, the optimizations in 2D result in an increase in heat transfer of 15% compared to the initial reference structure with an almost constant pressure loss or a reduction in pressure loss of 13% with an almost constant heat transfer. The optimizations in 3D result in improvements in the heat transfer of a maximum of 3.5% at constant pressure loss or 9% lower pressure losses at constant heat transfer compared to the initial reference structure. The subsequent experimental investigation shows that the theoretical improvements in heat transfer can only be demonstrated to a limited extent, as the fine contour changes cannot yet be reproduced by additive manufacturing. However, the improvements in pressure loss can be demonstrated experimentally following a cross-section correction. It can therefore be stated that with increasing accuracy of the manufacturing process, the improvements in heat transfer can also be utilized. [ABSTRACT FROM AUTHOR]

The main purpose of this investigation was to explore the heat transfer and flow characteristics of aero-foil-shaped fins combined with extended jet holes, specifically focusing on their feasibility in cooling turbine blades. In this study, a comprehensive investigation was carried out by applying impinging jet array cooling (IJAC) on a semi-circular curved surface, which was roughened using aerofoil-shaped fins. Numerical computations were conducted under three different Reynolds numbers (Re) ranging from 5000 to 25,000, while nozzle-to-target surface spacings (S/d) ranged from 0.5 to 8.0. Furthermore, an assessment was made of the impact of different fin arrangements, single-row (L1), double-row (L2), and triple-row (L3), on convective heat transfer. Detailed examinations were performed on area-averaged and local Nusselt (Nu) numbers, flow properties, and the thermal performance criterion (TPC) on finned and smooth target surfaces. The study's results revealed that the use of aerofoil-shaped fins and the reduction in S/d, along with surface roughening, led to significant increases in the local and area-averaged Nu numbers compared to the conventional IJAC scheme. The most notable heat transfer enhancement was observed at S/d = 0.5 utilizing extended jets and the surface design incorporating aerofoil-shaped fins. Under these specific conditions, the maximum heat transfer enhancement reached 52.81%. Moreover, the investigation also demonstrated that the highest TPC on the finned surface was achieved when S/d = 2.0 for L2 at Re = 25,000, resulting in a TPC value of 1.12. Furthermore, reducing S/d and mounting aerofoil-shaped fins on the surface yielded a more uniform heat transfer distribution on the relevant surface than IJAC with a smooth surface, ensuring a relatively more uniform heat transfer distribution to minimize the risk of localized overheating. [ABSTRACT FROM AUTHOR]