Search

Lithium–sulfur (Li-S) batteries offer a high theoretical energy density but suffer from poor cycling stability and polysulfide shuttling, which limits their practical application. To address these challenges, we developed a PANI-modified MoS2-NG composite, where MoS2 nanoflowers were uniformly grown on graphene oxide (GO) through PANI modification, resulting in an increased interlayer spacing of MoS2. This expanded spacing exposed more active sites, enhancing polysulfide adsorption and catalytic conversion. The composite was used to prepare MoS2-NG/PP separators for Li-S batteries, which achieved a high specific capacity of 714 mAh g−1 at a 3 C rate and maintained a low capacity decay rate of 0.085% per cycle after 500 cycles at 0.5 C. The larger MoS2 interlayer spacing was key to improving redox reaction kinetics and suppressing the shuttle effect, making the MoS2-NG composite a promising material for enhancing the performance and stability of Li-S batteries. [ABSTRACT FROM AUTHOR]

We report passively Q-switched pulse operation through an erbium-doped fiber laser (EDFL) utilizing graphene oxide/titania (GO/TiO2) nanorods as a saturable absorber. The GO/TiO2 nanorods were fabricated using a Sol–gel-assisted hydrothermal method. The optical and physical characterization of the GO/TiO2 was then characterized using a field-emission-scanning electron microscope (FE-SEM), energy-dispersive X-ray spectroscopy (EDS), and diffuses reflectance spectroscopy (DRS). To investigate the performance of the Q-switched EDFL based on the GO/TiO2 SA, the prepared nanorods were mechanically deposited on the fiber ferrule employing adhesion effects of in-dex-matching gel. This integration of the nanorod SA resulted in a self-starting Q-switching opera-tion initiated at a pump power of 17.5 mW and sustained up to 306.9 mW. When the pump range was tuned from 17.5 to 306.9 mW, the emission wavelength varied from 1564.2 to 1562.9 nm, pulse repetition rates increased from 13.87 kHz to 83.33 kHz, and pulse width decreased from 30.27 µs to 3.75 µs. Moreover, at the maximum pump power of 306.9 mW, the laser exhibited an average output power of 0.74 mW, a peak power of 1.54 mW, and a pulse energy of 8.88 nJ. Furthermore, this study investigates the GO/TiO2 damage threshold and prolonged stability of the proposed EDFL system. [ABSTRACT FROM AUTHOR]

Conductive polymer composites (CPCs) with nanocarbon fillers are at the high end of modern materials science, advancing current electronic applications. Herein, we establish the interplay between the chemistry and electrophysical properties of reduced graphene oxide (rGO), separately and as a filler for CPCs with the segregated structure conferred by the chemical composition of the initial graphene oxide (GO). A set of experimental methods, namely X-ray photoelectron spectroscopy (XPS), ultraviolet-visible spectroscopy, van der Paw and temperature-dependent sheet resistance measurements, along with dielectric spectroscopy, are employed to thoroughly examine the derived materials. The alterations in the composition of oxygen groups along with their beneficial effect on nitrogen doping upon GO reduction by hydrazine are tracked with the help of XPS. The slight defectiveness of the graphene network is found to boost the conductivity of the material due to facilitating the impact of the nitrogen lone-pair electrons in charge transport. In turn, a sharp drop in material conductivity is indicated upon further disruption of the π-conjugated network, predominantly governing the charge transport. Particularly, the transition from the Mott variable hopping transport mechanism to the Efros–Shklovsky one is signified. Finally, the impact of rGO chemistry and physics on the electrophysical properties of CPCs with the segregated structure is evaluated. Taken together, our results give a hint at how GO chemistry manifests the properties of rGO and the CPC derived from it, offering compelling opportunities for their practical applications. [ABSTRACT FROM AUTHOR]

To address the rapidly growing demand for high performance of lithium-ion batteries (LIBs), the development of high-capacity anode materials should focus on the practical perspective of a facile synthetic process. In this work, iron oxide nanoparticles (Fe3O4 NPs) in situ grown on the surface of reduced graphene oxide (rGO), denoted as Fe3O4 NPs@rGO, were prepared through a facile one-pot synthesis under the wet-colloidal conditions. The synthesized Fe3O4 NPs showed that uniform Fe3O4 NPs, with a size of around 9 nm, were distributed on the rGO surfaces. When applied as an anode material for LIBs, the Fe3O4 NPs@rGO anode revealed a high reversible capacity of 1191 mAh g−1 at 1.0 A g−1 after 200 cycles. It also exhibited excellent rate performance, achieving 608 mAh g−1 at a current density of 5.0 A g−1 over 500 cycles, with improved electronic and ionic conductivities due to the rGO template. This suggested that practically available anode materials can be developed through our one-pot synthesis by in situ growing the Fe3O4 NPs. [ABSTRACT FROM AUTHOR]

Sulfate anions (SO42−) are pivotal in various scientific and industrial domains, including mineralogy, biology, and materials science. While extensive research has elucidated sulfate hydration in bulk solids, liquids, and gaseous clusters, a significant gap persists in understanding sulfate interactions within two-dimensional materials, particularly graphene oxide (GO) nanosheets. This study investigates the intricate hydration phenomena and novel triple-interlayer lattice configurations that emerge from sulfate intercalation in GO nanosheets. Utilizing a straightforward methodology for obtaining precise X-ray measurements of confined nanospaces, we analyzed the temperature-dependent behavior and structural characteristics of these systems. Our findings reveal how sulfate ions modulate interlayer spacing, the dynamics of GO layers, and phase transitions. This research offers an atomic-scale understanding of hybrid hydration behaviors within confined SO4-H2O nano-environments, advancing our knowledge of sulfate interactions in two-dimensional materials. [ABSTRACT FROM AUTHOR]

Background/Objectives: Peripheral nerve injuries (PNIs) are a debilitating problem, resulting in diminished quality of life due to the continued presence of both chronic and acute pain. The current standard of practice for the repair of PNIs larger than 10 mm is the use of autologous nerve grafts. Autologous nerve grafts have limitations that often result in outcomes that are not sufficient to remove motor and sensory impairments. Bio-mimetic nanocomposite scaffolds combined with mesenchymal stem cells (MSCs) represent a promising approach for PNIs. In this study, we investigated the potential of an electrospun wrap of polycaprolactone (PCL) + graphene oxide (GO), with and without xenogeneic human adipose tissue-derived MSCs (hADMSCs) to use as a platform for neural tissue engineering. Methods: We evaluated, in vitro and in vivo, the potential of the nerve wrap in providing support for axonal growth. To establish the rat sciatic nerve defect model, a 10 mm long limiting defect was created in the rat sciatic nerve of 18 Lewis rats. Rats treated with the nanocomposites were compared with autograft-treated defects. Gait, histological, and muscle analyses were performed after sacrifice at 12 weeks post-surgery. Results: Our findings demonstrate that hADMSCs had the potential to transdifferentiate into neural lineage and that the nanocomposite successfully delivered hADMSCs to the injury site. Histologically, we show that the PCL + GO nanocomposite with hADMSCs is comparable to the autologous nerve graft, to support and guide axonal growth. Conclusions: The novel PCL + GO nerve wrap and hADMSCs used in this study provide a foundation on which to build upon and generate future strategies for PNI repair. [ABSTRACT FROM AUTHOR]

A novel sandwich-type electrochemical aptasensor based on supramolecularly immobilized affinity bioreceptor was prepared via host–guest interactions. This method utilizes an adamantane-modified, target-responsive hairpin DNA aptamer as a capture molecular receptor, along with a perthiolated β-cyclodextrin (CD) covalently attached to a gold-modified electrode surface as the transduction element. The proposed sensing strategy employed an enzyme-modified aptamer as the signalling element to develop a sandwich-type aptasensor for detecting prostate-specific antigen (PSA). To achieve this, screen-printed carbon electrodes (SPCEs) with electrodeposited reduced graphene oxide (RGO) and gold nanoferns (AuNFs) were modified with the CD derivative to subsequently anchor the adamantane-modified anti-PSA aptamer via supramolecular associations. The sensing mechanism involves the affinity recognition of PSA molecules on the aptamer-enriched electrode surface, followed by the binding of an anti-PSA aptamer–horseradish peroxidase complex as a labelling element. This sandwich-type arrangement produces an analytical signal upon the addition of H2O2 and hydroquinone as enzyme substrates. The aptasensor successfully detected the biomarker within a concentration range of 0.5 ng/mL to 50 ng/mL, exhibiting high selectivity and a detection limit of 0.11 ng/mL in PBS. [ABSTRACT FROM AUTHOR]

The use of nanoparticles in the industry carries the risk of their release into the environment. Based on the presumption that the primary graphene oxide (GO) toxicity mechanism is reactive oxygen species production in the cell, the question arises as to whether well-known antioxidants can protect the cell or significantly reduce the effects of GO. This study focused on the possible remedial effect of vitamin C in Acheta domesticus intoxicated with GO for whole lives. The reproduction potential was measured at the level of Vitellogenin (Vg) gene expression, Vg protein expression, hatching success, and share of nutrition in the developing egg. There was no simple relationship between the Vg gene's expression and the Vg protein content. Despite fewer eggs laid in the vitamin C groups, hatching success was high, and egg composition did not differ significantly. The exceptions were GO20 and GO20 + Vit. C groups, with a shift in the lipid content in the egg. Most likely, ascorbic acid impacts the level of Vg gene expression but does not affect the production of Vg protein or the quality of eggs laid. Low GO concentration in food did not cause adverse effects, but the relationship between GO toxicity and its concentration should be investigated more thoroughly. [ABSTRACT FROM AUTHOR]

Graphene and MXenes have emerged as promising materials for gas sensing applications due to their unique properties and superior performance. This review focuses on the fabrication techniques, applications, and sensing mechanisms of graphene and MXene-based composites in gas sensing. Gas sensors are crucial in various fields, including healthcare, environmental monitoring, and industrial safety, for detecting and monitoring gases such as hydrogen sulfide (H2S), nitrogen dioxide (NO2), and ammonia (NH3). Conventional metal oxides like tin oxide (SnO2) and zinc oxide (ZnO) have been widely used, but graphene and MXenes offer enhanced sensitivity, selectivity, and response times. Graphene-based sensors can detect low concentrations of gases like H2S and NH3, while functionalization can improve their gas-specific selectivity. MXenes, a new class of two-dimensional materials, exhibit high electrical conductivity and tunable surface chemistry, making them suitable for selective and sensitive detection of various gases, including VOCs and humidity. Other materials, such as metal-organic frameworks (MOFs) and conducting polymers, have also shown potential in gas sensing applications, which may be doped into graphene and MXene layers to improve the sensitivity of the sensors. [ABSTRACT FROM AUTHOR]

The fabrication process of reduced graphene oxide depends on many factors (e.g., graphite precursor, methods of oxidation, reduction, and exfoliation) which have a significant influence on the properties of this material. Therefore, their selection is not easy due to the large number of possible combinations of these factors. To overcome this problem, we proposed to use a multivariate analysis of variance method of finding associations between the qualitative type of independent variables and the quantitative type of dependent variable. Using ANOVA, we showed that the combination (interaction) of these variables is more important than the individual influence of the variables on the fabricated rGO. Knowing how the particular variables and their combinations affect the properties of rGO, it is easier to plan the fabrication process of this material. In this paper, we analyzed the number of oxide layers and designated the most promising oxides in terms of sensor gas application. Independently, we fabricated chemiresistor sensors and studied their response to NO2 in the analyzed atmosphere. We were able to combine the experimental results with statistical analysis indicating which oxidation methods and which graphite precursors will provide the best sensitivity. [ABSTRACT FROM AUTHOR]

Currently, one of the topical directions in the field of production and application of graphene-like nanostructures is the use of renewable natural raw materials, which have unlimited resources for an economically efficient large-scale yield of a product with environmental safety. In this regard, we present the production of graphene oxide (GO) from a renewable natural raw material of plant biomass, birch activated carbon (BAC), and a comparison of the obtained physicochemical, mechanical, and electrical properties of birch activated carbon–graphene oxide (BAC–GO) and graphite–graphene oxide (G–GO) synthesized from the initial materials, BAC and graphite (G). Results obtained from this study confirm the successful oxidation of BAC, which correlates well with the physical–chemical dates of the G–GO and BAC–GO samples. Change in data after the oxidation of graphite and BAC was facilitated by the structure of the starting materials and, presumably, the location and content of functional oxygen-containing groups in the G–GO and BAC–GO chains. Based on the results, the application of a cost-effective, eco-friendly colloidal solution of nanodispersed BAC–GO from a plant biomass-based high-quality resource for producing large-scale nanostructured graphene is validated which has potential applicability in nanoelectronics, medicine, and other fields. [ABSTRACT FROM AUTHOR]

Integrating hyperthermia with conventional cancer therapies shows promise in improving treatment efficacy while mitigating their side effects. Nanotechnology-based hyperthermia, particularly using superparamagnetic iron oxide nanoparticles (SPIONs), offers a simplified solution for cancer treatment. In this study, we developed composites of SPION quantum dots (Fe3O4) with reduced graphene oxide (Fe3O4/RGO) using the coprecipitation method and investigated their potential application in magnetic hyperthermia. The size of Fe3O4 nanoparticles was controlled within the quantum dot range (≤10 nm) by varying the synthesis parameters, including reaction time as well as the concentration of ammonia and graphene oxide, where their biocompatibility was further improved with the inclusion of polyethylene glycol (PEG). These nanocomposites exhibited low cytotoxic effects on healthy cells (CHO-K1) over an incubation period of 24 h, though the inclusion of PEG enhanced their biocompatibility for longer incubation periods over 48 h. The Fe3O4/RGO composites dispersed in acidic pH buffer (pH 4.66) exhibited considerable heating effects, with the solution temperature increasing by ~10 °C within 5 min of exposure to pulsed magnetic fields, as compared to their dispersions in phosphate buffer and aqueous dimethylsulfoxide solutions. These results demonstrated the feasibility of using quantum dot Fe3O4/RGO composites for magnetic hyperthermia-based therapy to treat cancer, with further studies required to systematically optimize their magnetic properties and evaluate their efficacy for in vitro and in vivo applications. [ABSTRACT FROM AUTHOR]

Cement-based composites (CBCs) are essential in the construction sector due to their cost-effectiveness, availability, and versatility, but they struggle with low tensile strength and poor heat resistance. Recent advancements have highlighted the potential of nanomaterials, particularly graphene oxide (GO), in enhancing the mechanical, thermal, and electrical properties of CBCs. This study aims to provide a comprehensive review of the incorporation of GO into cementitious composites, examining its impact on microstructure, mechanical properties, rheology, and durability; thus, a bibliometric review and scientometric analysis were conducted to thoroughly evaluate the existing literature. A total of 263 studies were selected for thorough study. It can be concluded that GO content acts as a pore filler, decreasing porosity by 23% and average pore size by 22%, while boosting compressive strength by up to 15% at a 0.05% concentration. It also enhances workability, stability, and resistance to chloride ingress, sulfate attack, alkali–silica reaction, and carbonation. Incorporating GO reduces cement consumption and carbon footprint, leading to more durable structures and supporting sustainable construction by efficiently utilizing waste materials. The optimal GO concentration for these benefits ranges from 0.03% to 0.1% by weight of cement, as higher concentrations may cause agglomeration. GO-modified cementitious materials are well suited for high-performance and durable applications, particularly in environments with chemical and mechanical stresses. [ABSTRACT FROM AUTHOR]

In this work, we report a study of a zinc sulfide (ZnS) nanocrystal and reduced graphene oxide (RGO) nanocomposite-based non-enzymatic uric acid biosensor. ZnS nanocrystals with different morphologies were synthesized through a hydrothermal method, and both pure nanocrystals and related ZnS/RGO were characterized with SEM, XRD and an absorption spectrum and resistance test. It was found that compared to ZnS nanoparticles, the ZnS nanoflakes had stronger UV light absorption ability at the wavelength of 280 nm of UV light. The RGO significantly enhanced the electron transfer efficiency of the ZnS nanoflakes, which further led to a better photoelectrochemical property of the ZnS/RGO nanocomposites. The ZnS nanoflake/RGO nanocomposite-based biosensor showed an excellent uric acid detecting sensitivity of 534.5 μA·cm−2·mM−1 in the linear range of 0.01 to 2 mM and a detection limit of 0.048 μM. These results will help to improve non-enzymatic biosensor properties for the rapid and accurate clinical detection of uric acid. [ABSTRACT FROM AUTHOR]

One-dimensional lithium-ion transport channels in lithium iron phosphate (LFP) used as a cathode in lithium-ion batteries (LIBs) result in low electrical conductivity and reduced electrochemical performance. To overcome this limitation, three-dimensional plasma-treated reduced graphene oxide (rGO) was synthesized in this study and used as an additive for LFP in LIB cathodes. Graphene oxide was synthesized using Hummers' method, followed by mixing with LFP, lyophilization, and plasma treatment to obtain LFP@rGO. The plasma treatment achieved the highest degree of reduction and porosity in rGO, creating ion transfer channels. The structure of LFP@rGO was verified through scanning electron microscopy (SEM) analysis, which demonstrated that incorporating 10.0 wt% of rGO into LFP resulted in successful coverage by the rGO layer, forming LFP@rGO-10. In half-cell tests, LFP@rGO-10 exhibited a specific capacity of 142.7 mAh g−1 at the 1.0 C-rate, which is higher than that of LFP. The full-cell exhibited 86.8% capacity retention after 200 cycles, demonstrating the effectiveness of rGO in enhancing the performance of LFP as an LIB cathode material. The outstanding efficiency and performance of the LFP@rGO-10//graphite cell highlight the promising potential of rGO-modified LFP as a cathode material for high-performance LIBs, providing both increased capacity and stability. [ABSTRACT FROM AUTHOR]

In this study, a new composite adsorbent, namely magnesium oxide modified graphene oxide (hereafter abbreviated GO@MgO), was prepared for the removal of Ibuprofen (IBU), a non-steroidal anti-inflammatory drug (NSAID) compound. Graphene oxide was modified with MgO to improve its properties. Several factors important for the evolution of the adsorption process were investigated, such as the dose of the adsorbent, the pH, and the initial IBU content, as well as the duration of the procedure and temperature. According to the results obtained, it was found that at pH 3.0 ± 0.1, by applying 0.5 g/L GO@MgO to 100 mg/L IBU, more than 80% was removed, reaching 96.3% with the addition of 1.5 g/L adsorbent in 24 h. After 30 min, the equilibrium was reached (77% removal) by adding 0.5 g/L of GO@MgO. This study proves that GO@MgO is capable of economical and efficient adsorption. The IBU kinetic data followed the pseudo-second-order kinetic model. Langmuir and Freundlich isotherm models were used to interpret the adsorption, but the Freundlich model described the adsorption method more accurately. The positive values of ΔH0 (14.465 kJ/mol) confirm the endothermic nature of the adsorption. Due to the increase of ΔG0 values with temperature, the adsorption of IBU on GO@MgO is considered to be spontaneous. [ABSTRACT FROM AUTHOR]

Three-dimensional hepatic cell cultures can provide an important advancement in the toxicity assessment of nanomaterials with respect to 2D models. Here, we describe liver organoids (LOs) obtained by assembling multiple cell lineages in a fixed ratio 1:1:0.2. These are upcyte® human hepatocytes, UHHs, upcyte® liver sinusoidal endothelial cells, LSECs, and human bone marrow-derived mesenchymal stromal cells, hbmMSCs. The structural and functional analyses indicated that LOs reached size stability upon ca. 10 days of cultivation (organoid maturation), showing a surface area of approximately 10 mm2 and the hepatic cellular lineages, UHHs and LSECs, arranged to form both primitive biliary networks and sinusoid structures, alike in vivo. LOs did not show signs of cellular apoptosis, senescence, or alteration of hepatocellular functions (e.g., dis-regulation of CYP3A4 or aberrant production of Albumin) for the entire culture period (19 days since organoid maturation). After that, LOs were repeatedly exposed for 19 days to a single or repeated dose of graphene oxide (GO: 2–40 µg/mL). We observed that the treatment did not induce any macroscopic signs of tissue damage, apoptosis activation, and alteration of cell viability. However, in the repeated dose regimen, we observed a down-regulation of CYP3A4 gene expression. Notably, these findings are in line with recent in vivo data, which report a similar impact on CYP3A4 when mice were repeatedly exposed to GO. Taken together, these findings warn of the potential detrimental effects of GO in real-life exposure (e.g., occupational scenario), where its progressive accumulation is likely expected. More in general, this study highlights that LOs formed by many cell lineages can enable repeated exposure regimens (suitable to mimic accumulation); thus, they can be suitably considered alternative or complementary in vitro systems to animal models. [ABSTRACT FROM AUTHOR]

Most earthen sites are located in open environments eroded by wind and rain, resulting in spalling and cracking caused by shrinkage due to constant water absorption and loss. Together, these issues seriously affect the stability of such sites. Gypsum–lime-modified soil offers relatively strong mechanical properties but poor water resistance. If such soil becomes damp or immersed in water, its strength is significantly reduced, making it unviable for use as a material in the preparation of earthen sites. In this study, we achieved the composite addition of a certain amount of sodium methyl silicate (SMS), titanium dioxide (TiO2), and graphene oxide (GO) into gypsum–lime-modified soil and analyzed the microstructural evolution of the composite-modified soil using characterization methods such as XRD, SEM, and EDS. A comparative study was conducted on changes in the mechanical properties of the composite-modified soil and original soil before and after immersion using water erosion, unconfined compression (UCS), and unconsolidated undrained (UU) triaxial compression tests. These analyses revealed the micro-mechanisms for improving the waterproof performance of the composite-modified soil. The results showed that the addition of SMS, TiO2, and GO did not change the crystal structure or composition of the original soil. In addition, TiO2 and GO were evenly distributed between the modified soil particles, playing a positive role in filling and stabilizing the structure of the modified soil. After being immersed in water for one hour, the original soil experienced structural instability leading to collapse. While the water absorption rate of the composite-modified soil was only 0.84%, its unconfined compressive strength was 4.88 MPa (the strength retention rate before and after immersion was as high as 93.1%), and the shear strength was 614 kPa (the strength retention rate before and after immersion was as high as 96.7%). [ABSTRACT FROM AUTHOR]

In this work, pine and birch wood were modified by graphene oxide using a single vacuum impregnation method. The research results indicate that the impregnation of wood with graphene oxide increases the crystallinity of cellulose in both pine and birch wood, and the increase in crystallinity observed in the case of birch was more significant than in the case of pine. FT-IR analyses of pine samples impregnated with graphene oxide showed changes in intensity in the absorption bands of 400–600, 700–1500 cm−1, and 3200–3500 cm−1 and a peak separation of 1102 cm−1, which may indicate new C-O-C connections. In the case of birch, only some differences were noticed related to the vibrations of the OH group. The proposed modification also affects changes in the color of the wood surface, with earlywood containing more graphene oxide than latewood. Analysis of scanning electron microscope images revealed that graphene oxide adheres flat to the cell wall. Considering the differences in the anatomical structure of both wood species, the research showed a statistically significant difference in water absorption and retention of graphene oxide in wood cells. Graphene oxide does not block the flow of water in the wood, as evidenced by the absorbability of the working liquid at the level of 580–602 kg/m3, which corresponds to the value of pure water absorption by wood in the impregnation method using a single negative pressure. In this case, higher graphene oxide retention values were obtained for pine wood. [ABSTRACT FROM AUTHOR]

This review explores the application of graphene-based materials (GBMs) in biomedicine, focusing on graphene oxide (GO) and its interactions with peptides and proteins. GO, a versatile nanomaterial with oxygen-containing functional groups, holds significant potential for biomedical applications but faces challenges related to toxicity and environmental impact. Peptides and proteins can be functionalized on GO surfaces through various methods, including non-covalent interactions such as π–π stacking, electrostatic forces, hydrophobic interactions, hydrogen bonding, and van der Waals forces, as well as covalent bonding through reactions involving amide bond formation, esterification, thiol chemistry, and click chemistry. These approaches enhance GO's functionality in several key areas: biosensing for sensitive biomarker detection, theranostic imaging that integrates diagnostics and therapy for real-time treatment monitoring, and targeted cancer therapy where GO can deliver drugs directly to tumor sites while being tracked by imaging techniques like MRI and photoacoustic imaging. Additionally, GO-based scaffolds are advancing tissue engineering and aiding tissues' bone, muscle, and nerve tissue regeneration, while their antimicrobial properties are improving infection-resistant medical devices. Despite its potential, addressing challenges related to stability and scalability is essential to fully harness the benefits of GBMs in healthcare. [ABSTRACT FROM AUTHOR]

Effectively detecting catechol (CC) and hydroquinone (HQ) simultaneously is crucial for environmental protection and human health monitoring. In the study presented herein, a novel electrochemical sensor for the sensitive simultaneous detection of CC and HQ was constructed based on an electrochemically reduced graphene oxide (ERGO)-modified multi-walled carbon nanotube paste electrode (MWCNTPE). Scanning electron microscopy, X-ray photoelectron spectroscopy, Raman spectroscopy and electrochemical techniques were utilized to characterize the sensing interface and investigate the sensing mechanism. Under the optimal detection conditions, the oxidation peak currents of CC and HQ show a good linear relationship with their concentrations in the range of 0.4–400 μM with a detection limit of 0.083 μM for CC and 0.028 μM for HQ (S/N = 3). Moreover, the sensor exhibits good performance and can be applied successfully in the simultaneous detection of CC and HQ in tap water samples and urine samples with satisfactory results, indicating its promising application prospects. [ABSTRACT FROM AUTHOR]

A novel nanocomposite film synthesized from an inexpensive and easily accessible polymer such as poly (vinyl alcohol) (PVA), which is coated with nickel sulfide (NiS) and graphene oxide (GO), was obtained from used drinking-water bottles. The produced coated film was examined as a potential photocatalyst film for wastewater treatment promotion in a batch system for the removal of methylene blue (MB) and tetracycline (TC) antibiotics. The experimental results show that the presence of GO significantly increases the photocatalytic efficiency of NiS, and the MB and TC degradation results proved that the incorporation of GO with NiS led to a more than one-and-a-half-fold increase in the removal percentage in comparison with the NiS/PVA-coated film. After 30 min of illumination using GO/NiS/PVA-coated film, the removal efficiency reached 86% for MB and 64% for TC. The photodegradation kinetic rate followed the pseudo-first-order rate. Furthermore, the response surface methodology (RSM) model was utilized to study and optimize several operating parameters. The ideal circumstances to achieve 91% elimination of MB are 12 mg L−1 MB initial concentration, two lamps, and an illumination time of 15 min; however, to achieve 85% TC removal, 11 mg L−1 TC initial concentration, two lamps, and a 45 min illumination time should be used. The fabricated nanocomposite photocatalyst film seems to have promise for use in water purification systems. [ABSTRACT FROM AUTHOR]

Alcoholic liver disease (ALD) develops when the immunotolerant environment of the liver is compromised due to excessive alcohol consumption. ALD progression involves variations in the expressions of multiple genes, resulting in liver inflammation and the development of a leaky gut. It is still unclear which molecular mechanism is involved in ALD progression, and due to that, there are currently no FDA-approved drugs available for its treatment. In this study, the protective effects of graphene oxide (GO) nanoparticles were investigated against ethanol-induced damage in the gut–liver axis in in vitro. GO was synthesized using a modified Hummer's method, and characterization was performed. Given the general concerns regarding nanoparticle toxicity, assessments of cell viability, lipid accumulation, DNA damage, cell death, and the generation of reactive oxygen species (ROS) were conducted using various techniques. Furthermore, the gene expressions of pro- and anti-inflammatory cytokines were determined using RT-qPCR. The findings reveal that GO promoted cell viability even against ethanol treatment. Additionally, lipid accumulation significantly decreased when cells were treated with GO alongside ethanol compared to ethanol treatment alone, with similar trends observed for other assays. A gene expression analysis indicated that GO treatment reduced the expression of proinflammatory cytokines while enhancing the expression of antioxidant genes. Moreover, GO treatment led to improvements in gut integrity and a reduction in proinflammatory cytokines in colon cells damaged by ethanol. These findings suggest that GO holds promise as a drug carrier, exhibiting no observed toxic effects. By shedding light on the protective effects of GO against ethanol-induced damage, this study contributes to the burgeoning field of nanoparticle-mediated therapy for ALD. [ABSTRACT FROM AUTHOR]

There is an urgent need to accurately quantify microRNA (miRNA)-based Alzheimer's disease (AD) biomarkers, which have emerged as promising diagnostic biomarkers. In this study, we present a rapid and universal approach to establishing a target miRNA-triggered rolling circle amplification (RCA) detection strategy, which achieves ultrasensitive detection of several targets, including miR-let7a-5p, miR-34a-5p, miR-206-3p, miR-9-5p, miR-132-3p, miR-146a-5p, and miR-21-5p. Herein, the padlock probe contains three repeated signal strand binding regions and a target miRNA-specific region. The target miRNA-specific region captures miRNA, and then the padlock probe is circularized with the addition of T4 DNA ligase. Subsequently, an RCA reaction is triggered, and RCA products containing multiple signal strand binding regions are generated to trap abundant fluorescein-labeled signal strands. The addition of exonuclease III (Exo III) causes signal strand digestion and leads to RCA product recycling and liberation of fluorescein. Ultimately, graphene oxide (GO) does not absorb the liberated fluorescein because of poor mutual interaction. This method exhibited high specificity, sensitivity, repeatability, and stability toward let-7a, with a detection limit of 19.35 fM and a linear range of 50 fM to 5 nM. Moreover, it showed excellent applicability for recovering miRNAs in normal human serum. Our strategy was applied to detect miRNAs in the plasma of APP/PS1 mice, demonstrating its potential in the diagnosis of miRNA-associated disease and biochemical research. [ABSTRACT FROM AUTHOR]

The particular properties of graphene oxide (GO) make it a material with great technological potential, so it is of great interest to find renewable and eco-friendly sources to satisfy its future demand sustainably. Recently, agricultural waste has been identified as a potential raw material source for producing carbonaceous materials. This study explores the potential of cashew nut shell (CNS), a typically discarded by-product, as a renewable source for graphene oxide synthesis. Initially, deoiled cashew nut shells (DCNS) were submitted to pyrolysis to produce a carbonaceous material (Py-DCNS), with process optimization conducted through response surface methodology. Optimal conditions were identified as a pyrolysis temperature of 950 °C and a time of 1.8 h, yielding 29.09% Py-DCNS with an estimated purity of 82.55%, which increased to 91.9% post-washing. Using a modified Hummers method, the Py-DCNS was subsequently transformed into graphene oxide (GO-DCNS). Structural and functional analyses were carried out using FTIR spectroscopy, revealing the successful generation of GO-DCNS with characteristic oxygen-containing functional groups. Raman spectroscopy confirmed the formation of defects and layer separations in GO-DCNS compared to Py-DCNS, indicative of effective oxidation. The thermogravimetric analysis demonstrated distinct thermal decomposition stages for GO-DCNS, aligning with the expected behavior for graphene oxide. Scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) further corroborated the morphological and compositional transformation from DCNS to GO-DCNS, showcasing reduced particle size, increased porosity, and significant oxygen functional groups. The results underscore the viability of cashew nut shells as a sustainable precursor for graphene oxide production, offering an environmentally friendly alternative to conventional methods. This innovative approach addresses the waste management issue associated with cashew nut shells and contributes to developing high-value carbon materials with broad technological applications. [ABSTRACT FROM AUTHOR]

This study explores the potential of graphene oxide (GO) as an additive in waterborne polyurethane (WPU) resins to create eco-friendly coatings with enhanced anticorrosive properties. Traditionally, WPU's hydrophilic nature has limited its use in corrosion-resistant coatings. We investigate the impact of incorporating various GO concentrations (0.01, 0.1, and 1.3 wt%) and functionalizing GO with ethylenediamine (EDA) on the development of anticorrosive coatings for carbon steel. It was observed, by potentiodynamic polarization analysis in a 3.5% NaCl solution, that the low GO content in the WPU matrix significantly improved anticorrosion properties, with the 0.01 wt% GO-EDA formulation showing exceptional performance, high Ecorr (−117.82 mV), low icorr (3.70 × 10−9 A cm−2), and an inhibition corrosion efficiency (η) of 99.60%. Raman imaging mappings revealed that excessive GO content led to agglomeration, creating pathways for corrosive species. In UV/condensation tests, the 0.01 wt% GO-EDA coating exhibited the most promising results, with minimal corrosion products compared to pristine WPU. The large lateral dimensions of GO sheets and the cross-linking facilitated by EDA enhanced the interfacial properties and dispersion within the WPU matrix, resulting in superior barrier properties and anticorrosion performance. This advancement underscores the potential of GO-based coatings for environmentally friendly corrosion protection. [ABSTRACT FROM AUTHOR]

Antimony (Sb) is one of the most concerning toxic metals globally, making the study of methods for efficiently removing Sb(III) from water increasingly urgent. This study uses graphene oxide and chitosan as the matrix (GOCS), modifying them with FeCl2 and four MnOx to form iron–manganese oxide (FM/GC) at a Fe/Mn molar ratio of 4:1. FM/GC quaternary composite microspheres are prepared, showing that FM/GC obtained from different MnOx exhibits significant differences in the ability to remove Sb(III) from neutral solutions. The order of Sb(III) removal effectiveness is MnSO4 > KMnO4 > MnCl2 > MnO2. The composite microspheres obtained by modifying GOCS with FeCl2 and MnSO4 are selected for further batch experiments and characterization tests to analyze the factors and mechanisms influencing Sb(III) removal. The results show that the adsorption capacity of Sb(III) decreases with increasing pH and solid–liquid ratio, and gradually increases with the initial concentration and reaction time. The Langmuir model fitting indicates that the maximum adsorption capacity of Sb(III) is 178.89 mg/g. The adsorption mechanism involves the oxidation of the Mn-O group, which converts Sb(III) in water into Sb(V). This is followed by ligand exchange and complex formation with O-H in FeO(OH) groups, and further interactions with C-OH, C-O, O-H, and other functional groups in GOCS. [ABSTRACT FROM AUTHOR]

This paper presents a recent investigation into the electromechanical behavior of thermally reduced graphene oxide (rGO) as a strain sensor undergoing repeated large mechanical strains up to 20.72%, with electrical signal output measurement in multiple directions relative to the applied strain. Strain is one the most basic and most common stimuli sensed. rGO can be synthesized from abundant materials, can survive exposure to large strains (up to 20.72%), can be synthesized directly on structures with relative ease, and provides high sensitivity, with gauge factors up to 200 regularly reported. In this investigation, a suspension of graphene oxide flakes was deposited onto Polydimethylsiloxane (PDMS) substrates and thermally reduced to create macroscopic rGO-strain sensors. Electrical resistance parallel to the direction of applied tension ( x ^ ) demonstrated linear behavior (similar to the piezoresistive behavior of solid materials under strain) up to strains around 7.5%, beyond which nonlinear resistive behavior (similar to percolative electrical behavior) was observed. Cyclic tensile testing results suggested that some residual micro-cracks remained in place after relaxation from the first cycle of tensile loading. A linear fit across the range of strains investigated produced a gauge factor of 91.50(Ω/Ω)/(m/m), though it was observed that the behavior at high strains was clearly nonlinear. Hysteresis testing showed high consistency in the electromechanical response of the sensor between loading and unloading within cycles as well as increased consistency in the pattern of the response between different cycles starting from cycle 2. [ABSTRACT FROM AUTHOR]

Lithium (Li) metal is regarded as a next-generation anode material owing to its high energy density. However, issues such as dendritic growth and volume changes during charging and discharging pose significant challenges for commercialization. We propose using lithiophilic reduced graphene oxide (rGO) and carbonized zeolite imidazolate framework-8 (C-ZIF-8) composites as host materials for Li to address these problems. The rGO/C-ZIF-8 composites are synthesized through a simple redox reaction followed by carbonization and are characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS). The roles of chemical composition, characteristics, and morphology are demonstrated. As a result of these favorable structural and functional properties, the Li symmetric cell with rGO/C-ZIF-8 exhibits a stable voltage profile for more than 100 h at 1 mA cm−2 without short-circuiting. A relatively low Li plating/stripping overpotential of ~101.5 mV at a high current density of 10 mA cm−2 is confirmed. Moreover, a rGO/C-ZIF-8-Li full cell paired with a LiFePO4 cathode demonstrates good cyclability and rate capability. [ABSTRACT FROM AUTHOR]

In the actual context of growing concerns over sustainability and energy efficiency, Phase Change Materials (PCMs) have gained attention as promising solutions for enhancing energy storage and release efficiency. On another hand, materials based on graphene oxide (GO) have proven antibacterial activity, biocompatibility, efficiency in microbial growth inhibition, and pollutant removal. Integrating nanoparticles into PCMs and creating Nano-Enhanced Phase Change Materials (NEPCMs) have opened new horizons for optimizing the performance of these systems and sustainable development. The key objective of this work is to gain insight into NECPMs, which are used in solar wall systems to enhance solar energy storage. Paraffin RT31 was mixed with Cu nanoparticles, graphene oxide (GO), and Cu-decorated GO (Cu@GO) at loading ratios ranging from 1% to 4% (w/w nanoparticles with respect to RT31). The compositions were characterized through Differential Scanning Calorimetry (DSC) and rheology tests. The decoration of the carbon-based nanoparticles was performed using the ultrasonication procedure, and the decoration efficiency was confirmed through X-ray Photoelectron Spectroscopy (XPS). The rheologic measurements were performed to correlate the flow behavior of the NEPCM with their composition at various temperatures. The study methodically investigated these composites' latent heat values, phase change peak temperatures, and solidification phase change temperatures. Compared to pure paraffin, the solidification of the formulations obtained using Cu@GO exhibits the largest increase in latent heat, with a 12.07% growth at a concentration of 2%. Additionally, at a 4% concentration of NEPCM, the largest increase in thermal conductivity was attained, namely 12.5%. [ABSTRACT FROM AUTHOR]

Herein, we introduce a simple precipitation method for preparing graphene oxide–silver nanoparticle (GO/AgNP) composites, utilizing Calendula officinalis (C. officinalis) seed extract as both a reducing and stabilizing agent. Our research combines the sustainable preparation of graphene oxide (GO) with the green synthesis of silver nanoparticles (AgNPs), aiming to explore the potential of the obtained composite as a novel antibacterial material. To establish a benchmark, the synthesis was also performed using sodium citrate, a conventional reducing agent. The resultant GO/AgNP composites were characterized through several analytical techniques, including scanning electron microscopy (SEM), transmission electron microscopy (TEM), atomic force microscopy (AFM), energy dispersive X-ray spectroscopy (EDS), Raman spectroscopy, X-ray diffraction (XRD), infrared (IR) spectroscopy, and ultraviolet–visible (UV-vis) spectroscopy, confirming the successful functionalization of GO with AgNPs. The antibacterial effectiveness of the composites was systematically assessed against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus), with nanoparticle concentrations spanning from 0 to 250 µg/mL, utilizing mostly disk diffusion and colony-forming unit (CFU) count assays. The AgNPs were characterized by a size range of 15–50 nm. Notably, the GO/AgNP composite prepared using C. officinalis seed extract demonstrated superior antibacterial activity at all tested concentrations, outperforming both pure GO and the GO/AgNP composite prepared with sodium citrate. The most pronounced antibacterial effect was observed at a concentration of 32.0 µg/mL. Therefore, this innovative synthesis approach may offer a valuable contribution to the development of new therapeutic agents to combat bacterial infections, suggesting further exploration into antibacterial coatings or potential drug development. [ABSTRACT FROM AUTHOR]

The objective of this study was to evaluate the effect of incorporating different concentrations of graphene oxide (GO) nanoparticles on the mechanical properties of a resin-modified glass ionomer cement (RMGIC). A commercial RMGIC (Resiglass R, Biodinâmica) was modified by incorporating 0.1% and 0.5% (by weight) of GO into the powder's material. An unmodified RMGIC was used as a control group. Powder samples were characterized using Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS). Specimens were fabricated and subjected to flexural strength (n = 15), modulus of elasticity (n = 15), Vicker's microhardness (n = 10), and surface roughness tests (n = 10). Data were analyzed using one-way ANOVA and Tukey's post hoc test (α = 5%). Experimental groups' powder demonstrated a homogeneous dispersion of GO. No statistically significant difference was observed in flexural strength (p = 0.067) and modulus of elasticity (p = 0.143) tests. The groups containing 0.1% and 0.5% GO showed significantly higher microhardness and lower surface roughness values (p < 0.001) compared to the control group. The incorporation of GO nanoparticles at concentrations of 0.1% and 0.5% improved the microhardness and surface roughness without negatively affecting the flexural strength and modulus of elasticity of an RMGIC. [ABSTRACT FROM AUTHOR]

Bone tissue engineering has seen significant advancements with innovative scaffold fabrication techniques such as 3D printing. This review focuses on enhancing polycaprolactone (PCL) scaffold properties through structural modifications, including surface treatments, pore architecture adjustments, and the incorporation of biomaterials like hydroxyapatite (HA). These modifications aim to improve scaffold conformation, cellular behavior, and mechanical performance, with particular emphasis on the role of mesenchymal stem cells (MSCs) in bone regeneration. The review also explores the potential of integrating nanomaterials and graphene oxide (GO) to further enhance the mechanical and biological properties of PCL scaffolds. Future directions involve optimizing scaffold structures and compositions for improved bone tissue regeneration outcomes. [ABSTRACT FROM AUTHOR]

The development of conductive coatings has significant implications for microelectronics and electrochemistry. However, conductive coatings may exhibit different electrochemical properties when prepared on different substrate materials. This research explores the comparative performance of graphene, graphene oxide (GO), and silver nanoparticle (Ag NP) composites as conductive coatings on diverse substrate materials, including polydimethylsiloxane (PDMS), polymethyl methacrylate (PMMA), and glass. The study employed various preparation methods, such as mixing conductive materials with substrate materials and preparing copolymer composite materials. The conductive coating approach was found to be the most straightforward and convenient, with broader development prospects and fewer restrictive conditions. The results indicate that the distinct surface characteristics of the substrate materials influence the conductive properties of coating materials. Consequently, results show that graphene exhibits the highest conductivity on all three substrates, while GO is more conductive than Ag NPs on PMMA and PDMS but less conductive than Ag NPs on glass. That offers valuable insights into the selection of substrate materials and coating materials for the preparation of conductive materials. [ABSTRACT FROM AUTHOR]

This study presents the development of luminol and gold nanoparticle co-functionalized graphene oxide (GO-AuNPs-L) hybrids as enhanced luminogenic signaling molecules in the chemiluminescence immunoassay (CLIA) for detecting C-reactive protein (CRP), a key biomarker of inflammation and cardiovascular diseases. When compared to free luminol, the GO-AuNPs-L hybrids significantly increased and prolonged the CL signal based on their synergistic enhancement in electron transfer during CL production. Based on the performance, the hybrids were employed as signaling molecules in both well plate-based and lateral flow CLIA platforms, showing substantial improvements in signal intensity and sensitivity in CRP detection. These results highlight the potential of GO-AuNPs-L hybrids as versatile and highly sensitive luminogenic molecules for immunological CRP detection, offering promising applications in clinical laboratory settings as well as in point-of-care diagnostics. [ABSTRACT FROM AUTHOR]

This paper reports the use of nanoparticles (NPs)-modified voltammetric sensors for the rapid determination of glycerol in the presence of ethanol and methanol, which are used in the transesterification reaction of biodiesel production. Two different modified electrodes have been prepared to form the electronic tongue (ET): copper hexacyanoferrate NPs obtained by chemical synthesis and mixed into graphite/epoxy (GEC) electrode, and nickel hydroxide NPs electrodeposited in reduced graphene oxide onto a GEC electrode. The response characteristics of these electrodes were first evaluated by building the respective calibration against glycerol, ethanol, and methanol. The electrodes demonstrated good stability during their analytical characterization, while principal component analysis confirmed the differentiated response against the different alcohols. Finally, the quantification of mixtures of these substances was achieved by a genetic algorithm-artificial neural networks (GA-ANNs) model, showing satisfactory agreement between expected and obtained values. [ABSTRACT FROM AUTHOR]

A plasma-reduced graphene oxide/lithium titanate oxide (PrGO/LTO) composite is prepared as an anode material to enhance the performance of lithium-ion capacitors (LICs). The PrGO/LTO composite is synthesized by mixing graphene oxide (GO) and LTO, followed by a series of freeze-drying and plasma-treatment processes. PrGO forms a porous three-dimensional (3D) structure with a large surface area, effectively preventing the restacking of PrGO while covering LTO. The GO/LTO mixing ratio is controlled to optimize the final structure for LIC applications. In lithium-ion half-cell assembly, the PrGO/LTO-based anode with an 80% mixing ratio exhibits the highest specific capacity of 73.0 mAh g−1 at 20 C. This is attributed to the optimized ratio for achieving high energy density from LTO and high power density from PrGO. In a LIC full-cell comprising PrGO/LTO as the anode and activated carbon as the cathode, the energy and power densities at 1 A g−1 are 40.3 Wh kg−1 and 2000 W kg−1, respectively, with a specific capacitance of 36.3 F g−1 and capacitance retention of 94.1% after 2000 cycles. Its outstanding performance, obtained from incorporating 3D-structured PrGO with LTO at an optimized ratio, lowers the cell resistance and provides efficient lithium-ion diffusion pathways. [ABSTRACT FROM AUTHOR]

The electrochemical performance of in-house developed, spark plasma-sintered, Aluminum metal–matrix composites (MMCs) was evaluated using different electrochemical techniques. X-ray diffraction (XRD) and Raman spectra were used to characterize the nanocomposites along with FE-SEM and EDS for morphological, structural, and elemental analysis, respectively. The highest charge transfer resistance (Rct), lowest corrosion current density, lowest electrochemical potential noise (EPN), and electrochemical current noise (ECN) were observed for GO-reinforced Al-MMC. The addition of honeycomb-like structure in the Al matrix assisted in blocking the diffusion of Cl− or SO4−2. However, poor wettability in between Al matrix and Al2O3 reinforcement resulted in the formation of porous interface regions, leading to a degradation in the corrosion resistance of the composite. Post-corrosion surface analysis by optical profilometer indicated that, unlike its counterparts, the lowest surface roughness (Ra) was provided by GO-reinforced MMC. [ABSTRACT FROM AUTHOR]

In the present work, the corrosion properties and the surface chemistry of a graphene oxide-coated AZ91D alloy were investigated. The coatings were deposited on the substrate specimens by immersion in solutions with GO concentrations of 0.05% and 0.1% (m/v). An intermediate silane layer was firstly obtained to improve adhesion between the GO films and the AZ91D substrate. The electrochemical behavior of the coated specimens was assessed using electrochemical impedance spectroscopy and potentiodynamic polarization curves in 3.5 wt.% NaCl solution. The surface chemistry was assessed using X-ray photoelectron spectroscopy (XPS). The GO films consisted of a mixture of carbon-based bonds (C-C, C-OH, C=O, and O-C=O). The surface morphology of the coated specimens was examined using scanning electron microscopy. The results revealed that the compactness of the GO films was dependent on the deposition conditions. The corrosion resistance was affected by the surface morphology. [ABSTRACT FROM AUTHOR]

We analyzed the interaction of three materials, reduced graphene oxide (RGO), [6,6]-phenyl-C61-butyric acid methyl ester (PCBM), and poly(3-hexylthiphene) (P3HT), as well as the dependence of its photophysical properties within the temperature range of 90 to 300 K. The nanocomposite of the films was analyzed by optical absorption ultraviolet–visible (UV-Vis) and photoluminescence (PL) and emission ellipsometry (EE) as a function of sample temperature. The surface morphology was studied by atomic force microscopy (AFM). We noted that onset levels (Eonset) of the nanocomposite of P3HT and RGO are smaller than the others. The PL spectra showed the presence of anomalies in the emission intensities in the nanocomposite of P3HT and PCBM. It was also possible to determine the electron–phonon coupling by calculating the Huang–Rhys parameters and the temperature dependence of samples. Through EE, it was possible to analyze the degree of polarization and the anisotropy. We observed a high degree of polarized emission of the P3HT films, which varies subtly according to the temperature. For nanocomposites with RGO, the polarization degree in the emission decreases, and the roughness on the surface increases. As a result, the RGO improves the energy transfer between adjacent polymer chains at the cost of greater surface roughness. Then, the greater energy transfer may favor applications of this type of nanocomposite in organic photovoltaic cells (OPVCs) with enhancement in energy conversion efficiency. [ABSTRACT FROM AUTHOR]

Slow-release fertilizer was developed by encapsulating NPK compound pellets with graphene oxide (GO) sheets employing a waterless synthesis technique. As-prepared GO sheets were characterized by XRD, Raman, XPS, FTIR, SEM, and EDS. The XRD patterns of the GO sheets indicate that the peak for the GO is observed at 2θ = 9.3°, and the peak (002) for graphite vanished. Moreover, a higher intensity ratio of the Raman ID/IG of the GO sheets than that of pristine graphite confirms the oxidation of the graphite. The FTIR and XPS analyses provided information on electronic structure, chemical structure, and oxygen-bonding neighbors. The SEM images indicated the GO sheet, whereby its morphology resembles a thin curtain or corrugated shape. The EDS spectrum of coated GO-F pellets revealed the distribution of C, O, N, P, and K elements in the synthesized materials. Afterwards, GO shell formation on fertilizer pellets greatly improved the slow-release characteristics of fertilizer, thus providing plants with their requisite nutrients and reducing environmental pollution. [ABSTRACT FROM AUTHOR]

Increasing the energy density and power of supercapacitors through hybrids of carbonaceous materials and metal oxides continues to be the subject of numerous research works. The correlation between specific capacitance and the properties of materials used as electrodes attracts great interest. In the present study, we investigated composites (GO/Mn3O4) prepared by the hydrothermal method with a variable ratio of GO/Mn3O4 and tested them as supercapacitor electrode materials in three- and two-electrode cells. The chemical characterization carried out by X-ray photoelectron spectroscopy and the adsorption techniques used allowed the determination of the surface carbon and oxygen content, as well as its textural properties. In this work, we analyzed the contribution of the double layer and the Faradaic reactions to the value of the final capacitance of the synthesized materials. Beyond empirically obtaining the electrochemical properties, these have been related to the physicochemical characteristics of the hybrids to help design materials with the best performance for supercapacitor electrodes. [ABSTRACT FROM AUTHOR]

This study aims at counteracting the problem of rejuvenated asphalt with poor performance and weak secondary anti-aging ability by improving the existing biomass rejuvenator. In this study, a carbon nanomaterial, graphene oxide (GO) with excellent anti-aging performance, was introduced to the wood tar-based rejuvenator (WR) to prepare a composite rejuvenator. Based on laboratory tests, the effects of the GO–wood tar-based composite rejuvenator (GWCR) on the performance of aged asphalt and on the secondary aging performance were investigated, and its rejuvenation mechanism was analyzed. The results indicate that the GWCR can increase the penetration, ductility, and creep rate (m) of aged asphalt while decreasing its softening point, rutting factor (G*/sinδ), and stiffness modulus (S). This indicates that the high-temperature resistance to the permanent deformation ability of aged asphalt degrades, while the low-temperature performance improves, and all values are slightly greater than those of the 70# original base asphalt. After PAV aging, the S value of the GO–wood tar-based composite rejuvenated asphalt (GWCRA) increased by 83.71%, while the m value decreased by 49.45%. The secondary aging resistance of the GWCRA is better than that of 70# original base asphalt, RA-75 rejuvenated asphalt, and wood tar-based rejuvenated asphalt. When adding the GWCR into aged asphalt, the content of saturates and aromatics in the asphalt increases by 1.08% and 11.1%, respectively. In contrast, the content of asphaltenes and resins decreases by 6.288% and 5.9%, respectively. As a result, the colloidal structure of the aged asphalt transfers from a gel to a sol–gel state. The surface roughness of the GWCRA increases by the synergistic effect of GO and wood tar, making its adhesion better than that of the 70# original base asphalt. Adding GO can improve the performance of wood tar rejuvenated asphalt (WRA) with high-temperature deformation resistance and resistance to secondary aging, and effectively make up for the defects in the performance of WRA rejuvenated asphalt, so as to extend the service life of asphalt pavements, thus increasing the value of wood tar engineering applications, which is of great practical significance. [ABSTRACT FROM AUTHOR]

The study utilized a simple and cost-effective approach to improve the photoelectrochemical (PEC) water-splitting performance of various materials, including reduced graphene oxide (rGO), tin oxide nanostructures (SnO2), and rGO/SnO2 composites. The composites examined were rS15, containing 15 mg of rGO and 45 mg of SnO2, and rS5, with 5 mg of rGO and 50 mg of SnO2, tested in a sodium hydroxide (NaOH) electrolyte. Notably, the rS5 electrode showed a significant increase in PEC efficiency in 0.1 M NaOH, achieving a peak photocurrent density of 13.24 mA cm−2 under illumination, which was seven times higher than that of pristine rGO nanostructures. This enhancement was attributed to the synergistic effects of the heterostructure, which reduced resistance and minimized charge recombination, thereby maximizing the catalytic activity across the various electrochemical applications. Furthermore, the rS5 anode demonstrated improved Tafel parameters, indicating faster reaction kinetics and lower overpotential for efficient current generation. These results highlight the potential for optimizing nanostructures to significantly enhance PEC performance, paving the way for advancements in sustainable water-splitting technologies. [ABSTRACT FROM AUTHOR]

The absence of adequate methods for hydrogen storage has prevented the implementation of hydrogen as a major source of energy. Graphene-based materials have been considered for use as solid hydrogen storage, because of graphene's high specific surface area. However, these materials alone do not meet the hydrogen storage standard of 6.5 wt.% set by the United States Department of Energy (DOE). They can, however, be easily modified through either decoration or doping to alter their chemical properties and increase their hydrogen storage capacity. This review is a compilation of various published reports on this topic and summarizes results from theoretical and experimental studies that explore the hydrogen storage properties of metal-modified graphene materials. The efficacy of alkali, alkaline earth metal, and transition metal decoration is examined. In addition, metal doping to further increase storage capacity is considered. Methods for hydrogen storage capacity measurements are later explained and the properties of an effective hydrogen storage material are summarized. [ABSTRACT FROM AUTHOR]

Graphene oxide (GO) nanosheets were functionalized with Schiff base and reduced Schiff base. Covalent and non-covalent functionalized GO nanostructures have been tested for the removal of pesticides with different chemical structures and properties (e.g., Epoxiconazole, Dimethomorph, Cyprodinil, Chlorothalonil, Acetochlor, Trifluralin) from aqueous solutions. The structure and morphology characteristics of the prepared structures were analyzed using techniques such as solid-state nuclear magnetic resonance (SSNMR), Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). Results of the experiments showed that, although the non-covalent functionalization did not affect the adsorption properties of GO much, the covalent functionalization increased the adsorption capacity of GO against the mentioned pesticides. [ABSTRACT FROM AUTHOR]

The application of carbon fiber in cement matrix has some disadvantages, such as poor dispersion and poor interfacial adhesion. In order to improve the interaction between carbon fiber and cement matrix and improve the properties of cement-based composites, carbon fiber was modified by electrophoretic deposition of nano-graphene oxide (GO). In this paper, the effects of doping CF into the cement matrix before and after GO modification are studied comparatively in terms of electrical conductivity, electrothermal warming effect, and pressure-sensitive properties of the cement matrix. It was found that the GO-modified CF reduces both the electrical resistivity of cementitious composites and the required level of fiber incorporation compared to CF. The percolation threshold is 0.7 wt% for CF and 0.5 wt% for GO-CF. The GO-modified CF is more effective than CF as a conductive filler to enhance the electrothermal warming performance of the cement matrix. When the GO-CF doping rate is 0.5%, the specimen temperature increases most rapidly, and the temperature rise value reaches a maximum of up to 30.45 °C, which is twice that of the CF group. When the fiber content is 0.7%, the pressure sensitivity of the sample was the best. When the fiber content is 0.5%, GO-CF can improve the pressure sensitivity of cement mortar specimens, and increase the resistance change rate of the cement mortar specimens by 5.7%. [ABSTRACT FROM AUTHOR]

Graphene oxide-silver poly(vinylidene fluoride) membranes (PVDF@GO-Ag) were successfully synthesized by the electrospinning method, which exhibited a high catalytic activity using the hydrogenation of 4-nitrophenol (4-NP) as a model reaction in a batch reaction study. The hybrid membranes doped with 1 wt% GO and 2 wt% Ag (PVDF-1-2) exhibited the most desired performance for the catalytic reduction of 4-NP. Importantly, PVDF-1-2 exhibited excellent cycling stability in 10 catalytic cycle tests and was highly amenable to separation. This property effectively addresses the significant challenges associated with the practical application of nanocatalysts. Furthermore, density-functional theory (DFT) calculations have demonstrated that the GO-Ag nanocomposites exhibit the strongest adsorption capacity for 4-NP− when a specific ratio of GO and Ag is achieved, accompanied by the loading of Ag nanoclusters onto GO. Additionally, the study demonstrated that an increase in temperature significantly accelerated the reaction rate, in line with the van't Hoff rule. This study provides an effective and environmentally friendly solution for the treatment of 4-NP in wastewater. [ABSTRACT FROM AUTHOR]

A systematic theoretical study on the molecular electronic structure of graphene and its oxides, including their interactions with molecular species of different polarity, was carried out. The influence of the O/C atomic ratio in the graphene oxides was also evaluated. Quantum chemical and COSMO-based statistical-thermodynamic calculations were performed. Geometry optimizations demonstrated that graphene sheets are structurally distorted by oxygen substitution, although they show high resistance to deformation. Furthermore, under axial O-C bonding, proton-donor and proton-acceptor centers are created on the graphene oxide surface, which could acquire an amphoteric character. In low-oxidized graphene oxides, H-bonding centers coexist with neutral highly polarizable π electron clouds. Deep graphene oxidation is also related to the formation of a quasi-two-dimensional H-bond network. These two phenomena are responsible for the exceptional adsorption and catalytic properties and the potential proton conductivity of graphene oxides. The current calculations demonstrated that the interactions of polar molecular species with deep-oxidized graphene derivatives are thermodynamically favorable, but not with low-oxidized ones. The capacity of the quantum chemical and COSMO-RS calculations to model all these issues opens the possibility of selecting or designing graphene-based materials with optimized properties for specific applications. Also, they are valuable in selecting/designing solvents with good exfoliant properties with respect to certain graphene derivatives. [ABSTRACT FROM AUTHOR]

Density functional theory and a semi-empirical quantum chemical approach were used to evaluate the photocatalytic efficiency of ceria (CeO2) combined with reduced graphene oxide (rGO) and graphene (GP) for degrading methylene blue (MB). Two main aspects were examined: the adsorption ability of rGO and GP for MB, and the separation of photogenerated electrons and holes in CeO2/rGO and CeO2/GP. Our results, based on calculations of the adsorption energy, population analysis, bond strength index, and reduced density gradient, show favorable energetics for MB adsorption on both rGO and GP surfaces. The process is driven by weak, non-covalent interactions, with rGO showing better MB adsorption. A detailed analysis involving parameters like fractional occupation density, the centroid distance between molecular orbitals, and the Lewis acid index of the catalysts highlights the effective charge separation in CeO2/rGO compared to CeO2/GP. These findings are crucial for understanding photocatalytic degradation mechanisms of organic dyes and developing efficient photocatalysts. [ABSTRACT FROM AUTHOR]