Search

Piezoelectric flags have functions of both classic flags and energy harvesting, and are becoming a new research focus. Interface circuits that convert wind energy to electrical energy are the key component of piezoelectric flags. A new structure for piezoelectric flags was designed to generate vibration by wind induction. After theoretical analysis, only SEH (standard energy harvesting) and SSHC (synchronized switch-harvesting-on capacitors) interface circuits were found suitable for piezoelectric flags. Simulation in Multisim was performed to compare SEH and SSHC in different load resistance. Experiments were carried out using different wind speeds. The on-time and delay-time of each switch were controlled by the proposed control algorithm. Both simulation and experimental results indicate that the output voltage with SSHC is higher than the output voltage with SEH. When the resistance is 1700 kΩ and the wind speed is 24 m/s, the output power of SSHC can be increased by 45.63% compared with the SEH circuit. [ABSTRACT FROM AUTHOR]

In the preparation of (Ba,Ca)(Zr,Ti)O3 lead-free piezoelectric ceramics, different Ca2+ and Zr4+ contents will greatly affect the phase structure, microstructure, and electrical properties of the ceramics. XRD shows that all samples have pure perovskite phase structure, and the (Ba0.85Ca0.15)(ZryTi1−y)O3 ceramics morphotropic phase boundary region from tetragonal phase to rhombohedral phase near 0.08 ≤ y ≤ 0.1. From the dielectric temperature curve, the phase transition temperature (TO-T) was found near room temperature at 0.12 ≤ x ≤ 0.18 for the (Ba1−xCax)(Zr0.1Ti0.9)O3 ceramics. Both Ca2+ and Zr4+ increase have a significant decrease on the Curie temperature Tc. All samples were revealed as relaxers with diffusivities in the range 1.29 ≤ γ ≤ 1.82. Different from the undoped ceramics, ceramics doped with Ca and Zr ions exhibit saturated P–E hysteresis loops, and their ferroelectric properties are significantly optimized. In particular, the (Ba0.85Ca0.15)(Zr0.1Ti0.9)O3 ceramic demonstrated optimal properties, namely d33 = 330 pC/N, kp = 0.41, εr = 4069, Pr = 4.8 μC/cm2, and Ec = 3.1 kV/cm, indicating that it is a viable lead-free piezoelectric contender. Variations in Ca and Zr content have a significant effect on the crystal grain sizes and densities of ceramics, which is strongly associated with their piezoelectricity. [ABSTRACT FROM AUTHOR]

Air bearing has been widely applied in ultra-precision machine tools, aerospace and other fields. The restrictor of the porous material is the key component in air bearings, but its performance is limited by the machining accuracy. A combination of optimization design and material modification of the porous alumina ceramic membrane is proposed to improve performance within an air bearing. Porous alumina ceramics were prepared by adding a pore-forming agent and performing solid-phase sintering at 1600 °C for 3 h, using 95-Al2O3 as raw material and polystyrene microspheres with different particle sizes as the pore-forming agent. With 20 wt.% of PS50, the optimum porous alumina ceramic membranes achieved a density of 3.2 g/cm3, a porosity of 11.8% and a bending strength of 150.4 MPa. Then, the sintered samples were processed into restrictors with a diameter of 40 mm and a thickness of 5 mm. After the restrictors were bonded to aluminum shells for the air bearing, both experimental and simulation work was carried out to verify the designed air bearing. Simulation results showed that the load capacity increased from 94 N to 523 N when the porosity increased from 5% to 25% at a fixed gas supply pressure of 0.5 MPa and a fixed gas film thickness of 25 μm. When the gas film thickness and porosity were fixed at 100 μm and 11.8%, respectively, the load capacity increased from 8.6 N to 40.8 N with the gas supply pressure having been increased from 0.1 MPa to 0.5 MPa. Both experimental and simulation results successfully demonstrated the stability and effectiveness of the proposed method. The porosity is an important factor for improving the performance of an air bearing, and it can be optimized to enhance the bearing's stability and load capacity. [ABSTRACT FROM AUTHOR]

Brassinolide (BR) is the "sixth class" plant hormone, which plays an important role in various physiological and biochemical processes of plants. The wide variety of functions of Pinellia ternata means that there is huge demand for it and thus it is in short supply. This paper mainly assessed the changes of yield and quality in P. ternata at different stages after BR treatments by principal component analysis, in order to improve the yield and quality of P. ternata and at the same time determine the best harvest time. The results showed that the tuber yield of P. ternata was significantly increased by BR treatments at different stages (except for the 15th day). After the 15th, 45th, 60th, 75th, 90th, and 105th day of treatments, the tuber yield of P. ternata reached peak values at 0.10 (0.65 g), 0.50 (1.97 g), 0.50 (1.98 g), 1.00 (2.37 g), 1.00 (2.84 g), and 2.00 mg/L (3.76 g) BR treatment, respectively. The optimal harvest time was the 75th day after 0.10, 0.50, and 1.00 mg/L BR treatments, which not only significantly improved the yield of P. ternata, but also retained high level of total alkaloids in the tubers (20.89, 5.37, and 13.44%) and bulbils (9.74, 20.42, and 13.62%), high total flavone content in the tubers (17.66, 16.26, and 12.74%) and bulbils (52.63, 12.79, and 38.69%), and high β-sitosterol content in the tubers (25.26, 16.65, and 0.62%) of P. ternata, compared with the control, respectively. [ABSTRACT FROM AUTHOR]