Search

Over the past few years, polymer nanocomposites have garnered a significant amount of interest from both the scientific community and industry due to their remarkable versatility and wide range of potential uses in various fields, including automotive, electronics, medicine, textiles and environmental applications. In this regard, this study focuses on the influence of a compatibilizer rubber on a nanocomposite incorporating graphene nanoparticles (GNPs), with a polymer matrix based on a blend of polypropylene (PP) and polyethylene terephthalate (PET). This effect has been investigated on both isotropic samples and on anisotropic/spun fiber samples. The influence of the compatibilizer rubber on morphological, rheological and mechanical properties was analysed and discussed. Mechanical and morphological properties were evaluated on both isotropic samples obtained by compression moulding and melt-spun fibers. The addition of the rubbery compatibilizer increased the viscosity, improving interfacial adhesion, and the same effect was observed for the melt strength and breaking stretching ratios. Mechanical properties, including the elastic modulus, tensile strength and elongation at break, improved in both types of samples but more significantly in the fibers. These improvements were attributed to the orientation of the matrix, the formation of PET microfibrils, and the reduction in the size of graphene nanoparticles due to the action of the elongational flow. This reduction, facilitated by the elongation flow and the action of the compatibilizer, improved matrix–nanofiller adhesion due to the increased contact area between the two polymeric phases and between the filler and matrix. Finally, a transition from brittle to ductile behaviour was observed, particularly in the system with the compatibilizer, attributed to defect reduction and improved stress transmission. [ABSTRACT FROM AUTHOR]

During the processing and during their lifetime, polymers are subjected to several environmental stresses—thermomechanical, photo-oxidative, etc.—that can strongly modify their chemical and molecular structure and, consequently, their morphology. Reduction of the molecular weight and formation of double bonds and oxygenated groups are the main changes observed as a consequence of the degradation. As a result of these changes, the macroscopic properties are dramatically modified. These changes can have a relevant effect if the post-consumer plastic manufacts are recycled. In this work, a sample of polypropylene subjected to two different degradation histories—photo-oxidation in air and in marine water—is reprocessed two times in a mini twin-screw extruder in the same processing conditions. The effect of the thermomechanical degradation during the reprocessing is different. Indeed, the less severe degraded sample shows a higher degradation level during reprocessing because the shear stress is larger. This means that the thermomechanical degradation kinetics is larger in the less degraded samples. Nevertheless, the final properties of the recycled polymers are different because the properties of the photo-oxidized samples before reprocessing were very different. [ABSTRACT FROM AUTHOR]

Compact discs (CDs) and digital versatile discs (DVDs) are mainly made by polycarbonate disc, a thin layer of aluminum or silver, a thin layer of a coating and a thin layer of a label of paper or PET. The recycling of these discs is difficult due to the removal of these non-polymeric layers and to our best knowledge, no industrial plants have been resent for their recycling. In this work, we propose a facile way to remove the non-polymeric layers and investigate the effect of the repetitive extrusion process on the processability and on the mechanical properties of the recycled polycarbonate. A few works have been published dealing with both the removal of the non-polymeric layers and the mechanical recycling of the disk of polycarbonate. In our approach, the removal of the non-polymeric layers is easily obtained through a thermo-mechanical treatment in a basic solution by ammonia. This process can be considered green because is made at a low temperature with a small amount of water and a very small amount of ammonia, saving energy and water. The properties of the polycarbonate remain good if the mechanical recycling is made after drying the post-consumer polycarbonate. [ABSTRACT FROM AUTHOR]

Biodegradable Mater-Bi (MB) composites reinforced with hazelnut shell (HS) powder were prepared in a co-rotating twin-screw extruder followed by compression molding and injection molding. The effects of reinforcement on the morphology, static and dynamic mechanical properties, and thermal and rheological properties of MB/HS biocomposites were studied. Rheological tests showed that the incorporation of HS significantly increased the viscosity of composites with non-Newtonian behavior at low frequencies. On the other hand, a scanning electron microscope (SEM) examination revealed poor interfacial adhesion between the matrix and the filler. The thermal property results indicated that HS could act as a nucleating agent to promote the crystallization properties of biocomposites. Furthermore, the experimental results indicated that the addition of HS led to a significant improvement in the thermomechanical stability of the composites. This paper demonstrates that the incorporation of a low-cost waste product, such as hazelnut shells, is a practical way to produce low-cost biocomposites with good properties. With a content of HS of 10%, a remarkable improvement in the elastic modulus and impact strength was observed in both compression and injection-molded samples. With a higher content of HS, however, the processability in injection molding was strongly worsened. [ABSTRACT FROM AUTHOR]

Synthetic biopolymers are effective cues to replace damaged tissue in the tissue engineering (TE) field, both for in vitro and in vivo application. Among them, poly-l-lactic acid (PLLA) has been highlighted as a biomaterial with tunable mechanical properties and biodegradability that allows for the fabrication of porous scaffolds with different micro/nanostructures via various approaches. In this review, we discuss the structure of PLLA, its main properties, and the most recent advances in overcoming its hydrophobic, synthetic nature, which limits biological signaling and protein absorption. With this aim, PLLA-based scaffolds can be exposed to surface modification or combined with other biomaterials, such as natural or synthetic polymers and bioceramics. Further, various fabrication technologies, such as phase separation, electrospinning, and 3D printing, of PLLA-based scaffolds are scrutinized along with the in vitro and in vivo applications employed in various tissue repair strategies. Overall, this review focuses on the properties and applications of PLLA in the TE field, finally affording an insight into future directions and challenges to address an effective improvement of scaffold properties. [ABSTRACT FROM AUTHOR]

Fibers spun by melt spinning of binary and ternary polypropylene/ polyethylenetherephthalate blends have been produced and characterized in order to investigate the effect of a compatibilizer on their morphology and mechanical properties. The compatibilizer was a maleic anhydride-functionalized rubber copolymer. The effect of the compatibilizer was well evident in the isotropic state, as the morphology became very fine, the size of the dispersed particles was very small, and the adhesion was better. The effect of the compatibilizer on the mechanical properties is very relevant, especially in the elongation at break. On the contrary, no relevant effect was observed in the anisotropic oriented fibers. Although the average diameter of the microfibrils of the dispersed phase of the compatibilized blend generated during the hot drawing was much smaller than that of the microfibrils of the same particles of the uncompatibilized blend, the mechanical properties were almost the same. This behavior has been attributed to the length of the smaller microfibrils of the ternary blends, which was lower that of the microfibrils of the binary blend. This has been explained in terms of reduced initial droplet size, and therefore of lesser possibility of stretching the droplets to very long fibrils in these samples. [ABSTRACT FROM AUTHOR]

The effect of graphene nanoplatelets (GnPs) on the morphology, rheological, and mechanical properties of isotropic and anisotropic polypropylene (PP)/recycled polyethylene terephthalate (rPET)-based nanocomposite are reported. All the samples were prepared by melt mixing. PP/rPET and PP/rPET/GnP isotropic sheets were prepared by compression molding, whereas the anisotropic fibers were spun using a drawing module of a capillary viscometer. The results obtained showed that the viscosity of the blend is reduced by the presence of GnP due to the lubricating effect of the graphene platelets. However, the Cox–Merz rule is not respected. Compared to the PP/rPET blend, the GnP led to a slight increase in the elastic modulus. However, it causes a slight decrease in elongation at break. Morphological analysis revealed a poor adhesion between the PP and PET phases. Moreover, GnPs distribute around the droplets of the PET phase with a honey-like appearance. Finally, the effect of the orientation on both systems gives rise not only to fibers with higher modulus values, but also with high deformability and a fibrillar morphology of the dispersed PET phase. A fragile-ductile transition driven by the orientation was observed in both systems. [ABSTRACT FROM AUTHOR]

It is well known that the need for more environmentally friendly materials concerns, among other fields, the food packaging industry. This regards also, for instance, nets used for agricultural product (e.g., citrus fruits, potatoes) packaging. These nets are typically manufactured by film blowing technique, with subsequent slicing of the films and cold drawing of the obtained strips, made from traditional, non-biodegradable polymer systems. In this work, two biodegradable polymer systems were characterized from rheological, processability, and mechanical points of view, in order to evaluate their suitability to replace polyethylene-based polymer systems typically used for agricultural product net manufacturing. Furthermore, laboratory simulation of the above-mentioned processing operation paths was performed. The results indicated a good potential for biodegradable polymer systems to replace polyethylene-based systems for agricultural product packaging. [ABSTRACT FROM AUTHOR]

Irrigation tubes based on biodegradable polymers were prepared via an extrusion-drawing process by Irritec and compared to conventional pipes made of high-density polyethylene (HDPE). A commercial polylactide/poly (butyleneadipate-co-butyleneterephthalate) (PLA/PBAT) blend (Bio-Flex®) and Mater-Bi® were used. The polymers were characterized from rheological and mechanical points of view. Irrigation pipes were subjected to photoaging with continued exposure to UV radiation up to 22 days. The degradability in the soil of irrigation tube samples was studied. The influence of temperature and UV irradiation on soil burial degradation was investigated. A soil burial degradation test was carried out at 30 °C and 50 °C for up to 70 days. The degree of degradation was evaluated from the weight loss percentage. The degradation rate of irrigation tube samples based on Mater-Bi® was higher at 30 °C and was stimulated after 14 days of UV irradiation. Higher temperatures or UV aging encouraged the disintegration in soil of Bio-Flex®-based irrigation tubes. Furthermore, tube samples, before and after UV and soil burial degradation, were analyzed by Attenuated Total Reflection-Fourier Transform Infra-Red (ATR-FTIR) spectroscopy. [ABSTRACT FROM AUTHOR]

The use of polyamide/polyolefin blends has gained importance and concern for years, but they also show some issues to be adequately addressed, such as the incompatibility between the two components. This is usually overcome by using suitable compatibilizers, typically based on functionalized polyolefins. However, there is only little information about the use of a degraded polyolefins to induce compatibilization. This is even truer, as far as polyamide 6/polypropylene (PA6/PP) blends are concerned. In this work, compatibilization of PA6/PP blends by using small amounts of photo-oxidized PP was investigated; furthermore, the effects due to the presence of the photo-oxidized PP were studied also in relationship to the spinning operation, where the existence of the non-isothermal elongational flow can lead to significant, further morphological changes. It was found that isotropic samples showed significant enhancements of the tensile properties upon adding the photo-oxidized PP. Under non-isothermal elongational flow conditions, the presence of the photo-oxidized PP was particularly effective in improving the mechanical properties in comparison to the uncompatibilized blend fibers. Furthermore, an important result was found: The elongational-flow processing allowed obtaining anisotropic samples where the improvements of the properties, in comparison to the isotropic samples, were similar to those achieved by using a compatibilizer. [ABSTRACT FROM AUTHOR]

Polyamide/polyolefin blends have gained attention from the academia and the industry for several years. However, in order to optimize their properties, some drawbacks such as chemical incompatibility must be adequately overcome. This can be done by adding suitable compatibilizers. On the other hand, it is less known that suitable processing techniques may also lead to significant results. In a previous work on a low-density polyethylene/polyamide 6 (LDPE/PA6) blend, we found that the orientation due to elongational flow processing conditions could lead to an unexpected brittle–ductile transition. In this work, this phenomenon was further investigated and the attention was mainly focused on the effects that processing can have on the morphology and, as a consequence, on the final properties of a polymer blends. With regard to LDPE/PA6 blend, an important result was found, i.e., the effects on the ductility induced by the elongational flow orientation are similar to those obtained by using an ethylene-glycidyl methacrylate compatibilizer. [ABSTRACT FROM AUTHOR]

The use of biodegradable/bio-based polymers is of great importance in addressing several issues related to environmental protection, public health, and new, stricter legislation. Yet some applications require improved properties (such as barrier or mechanical properties), suggesting the use of nanosized fillers in order to obtain bio-based polymer nanocomposites. In this work, bionanocomposites based on two different biodegradable polymers (coming from the Bioflex and MaterBi families) and two different nanosized fillers (organo-modified clay and hydrophobic-coated precipitated calcium carbonate) were prepared and compared with traditional nanocomposites with high-density polyethylene (HDPE) as matrix. In particular, the injection molding processability, as well as the mechanical and rheological properties of the so-obtained bionanocomposites were investigated. It was found that the processability of the two biodegradable polymers and the related nanocomposites can be compared to that of the HDPE-based systems and that, in general, the bio-based systems can be taken into account as suitable alternatives. [ABSTRACT FROM AUTHOR]

The use of polyamide/polyolefin blends has gained importance and concern for years, but they also show some issues to be adequately addressed, such as the incompatibility between the two components. This is usually overcome by using suitable compatibilizers, typically based on functionalized polyolefins. However, there is only little information about the use of a degraded polyolefins to induce compatibilization. This is even truer, as far as polyamide 6/polypropylene (PA6/PP) blends are concerned. In this work, compatibilization of PA6/PP blends by using small amounts of photo-oxidized PP was investigated; furthermore, the effects due to the presence of the photo-oxidized PP were studied also in relationship to the spinning operation, where the existence of the non-isothermal elongational flow can lead to significant, further morphological changes. It was found that isotropic samples showed significant enhancements of the tensile properties upon adding the photo-oxidized PP. Under non-isothermal elongational flow conditions, the presence of the photo-oxidized PP was particularly effective in improving the mechanical properties in comparison to the uncompatibilized blend fibers. Furthermore, an important result was found: The elongational-flow processing allowed obtaining anisotropic samples where the improvements of the properties, in comparison to the isotropic samples, were similar to those achieved by using a compatibilizer.

Fibers spun by melt spinning of binary and ternary polypropylene/polyethylenetherephthalate blends have been produced and characterized in order to investigate the effect of a compatibilizer on their morphology and mechanical properties. The compatibilizer was a maleic anhydride-functionalized rubber copolymer. The effect of the compatibilizer was well evident in the isotropic state, as the morphology became very fine, the size of the dispersed particles was very small, and the adhesion was better. The effect of the compatibilizer on the mechanical properties is very relevant, especially in the elongation at break. On the contrary, no relevant effect was observed in the anisotropic oriented fibers. Although the average diameter of the microfibrils of the dispersed phase of the compatibilized blend generated during the hot drawing was much smaller than that of the microfibrils of the same particles of the uncompatibilized blend, the mechanical properties were almost the same. This behavior has been attributed to the length of the smaller microfibrils of the ternary blends, which was lower that of the microfibrils of the binary blend. This has been explained in terms of reduced initial droplet size, and therefore of lesser possibility of stretching the droplets to very long fibrils in these samples.