Search

Rapid growth in a number of developing nations' mobile telecommunications sectors presents network operators with difficulties such as poor service quality and congestion, mostly because these locations lack a dependable and reasonably priced electrical source. In order to provide a sustainable and reasonably priced energy alternative for the developing world, this study provides a detailed examination of the core ideas behind renewable energy technology (RET). A multi-agent-based small-scaled smart base transceiver station (BTS) site reinforcement strategy is presented to manage energy resources by boosting resilience so to supply power to essential loads in peak demand periods by leveraging demand-side management (DSM). Diverse energy sources are combined to create interconnected BTS sites, which enable energy sharing to balance fluctuations by establishing a market that promotes economical energy. A MATLAB simulation model was developed to assess the effectiveness of the proposed system by using real load data and fast electric vehicle charging loads from five different base transceiver stations (BTSs) located throughout Pakistan's southern area. In this proposed study, the base transceiver station (BTS) sites can share their energy through a multi-agent-based system. From the results, it is observed that, after optimization, the base transceiver station (BTS) sites trade their energy with the grid at rate of 0.08 USD/kWh and with other sites at a rate of 0.04 USD/kWh. Therefore, grid dependency is decreased by 44.3% and carbon emissions are reduced by 71.4% after the optimization of the base transceiver station (BTS) sites. [ABSTRACT FROM AUTHOR]

In response to escalating concerns about climate change, there is a growing imperative to prioritize the decarbonization of the telecom sector and effectively reduce its carbon emissions. This study presents a thorough techno-economic optimization framework for implementing renewable-dominated hybrid standalone systems for the base transceiver station (BTS) encapsulation telecom sector in Pakistan. It is noted that from the results obtained from 42 BTS sites overall, 21 BTS sites had a feasible combination of a photovoltaic battery system, having a diesel generator as a backup source with an average LCOE of 0.1246 USD/kWh to 0.2325 USD/kWh. Thus, seven BTS sites had an optimal combination of biomass, with photovoltaic and battery storage systems and with a varied LCOE of 0.1175 USD/kWh to 0.1318 USD/kWh. Moreover, due to the high flow of hydro water in the north region, five BTS sites presented an ideal configuration of a hydro system coupled with a photovoltaic, wind, and battery storage system, with a varied LCOE of 0.04547 USD/kWh to 0.07419 USD/kWh. Wind energy systems are dominant in the southern region; therefore, five BTS sites presented an ideal combination of a wind energy system coupled with a photovoltaic battery storage system, having DGs as backup sources for sustainability and with a varied LCOE of 0.1096 USD/kWh to 0.1294 USD/kWh. In addition, 02 BTSs had an optimal combination of photovoltaic systems coupled with hydro and wind systems, with diesel generators having a varied LCOE of 0.07618 USD/kWh to 0.04575 USD/kWh. The remaining 02 BTS sites had a feasible combination of wind–hydro-battery and diesel generator–photovoltaic–hydro-battery systems, with an LCOE of 0.7035 USD/kWh and 0.1073 USD/kWh, respectively. Finally, an environmental analysis based on carbon emissions, as well as sensitivity analyses based on different uncertainties, i.e., wind speed, solar irradiance, inflation rate, discount rate, and load demand, was performed to evaluate the behavior of the proposed systems. The optimization of these systems and comparative study findings indicate that the hybrid BTS system is the best option, better than conventional diesel-operated BTS systems in terms of cost-effectiveness, environmental friendliness, and sustainability. [ABSTRACT FROM AUTHOR]

The COVID-19 pandemic has led to significant changes in healthcare practices, including increased antibiotic usage. This study aimed to investigate the impact of the pandemic on the prevalence of extended-spectrum β-lactamase (ESBL) production and carbapenem resistance among key bacterial species causing urinary tract infections (UTIs). Conducted at King Fahad Medical City in Riyadh from January 2018 to December 2022, the study analyzed urine samples from 9697 UTI patients. Patients were categorized into 'pre-COVID-19' and 'during COVID-19' groups. Bacterial isolates were identified, and antimicrobial susceptibility testing was performed following guidelines. ESBL production was detected using the Double-Disc Synergy Test. Escherichia coli and Klebsiella pneumoniae were the main pathogens. During the pandemic, ESBL production decreased in E. coli by 1.9% and in K. pneumoniae by 6.0%. Carbapenem resistance also declined, with E. coli displaying a 1.2% reduction and K. pneumoniae and Pseudomonas aeruginosa displaying 10.7% and 7.9% reductions, respectively. Notably, logistic regression analysis revealed that the odds of ESBL presence were 10% lower during the COVID-19 pandemic (OR 0.91; 95% CI 0.83–0.99; p = 0.040), and there was a significant reduction in the odds of carbapenem resistance (OR 0.43; 95% CI 0.37–0.51; p < 0.001). This study reveals a significant decrease in ESBL production and carbapenem resistance among UTI pathogens during the COVID-19 pandemic, hinting at the impact of modified antibiotic and healthcare approaches. It emphasizes the need for persistent antimicrobial resistance surveillance and policy adaptation to address resistance challenges, offering key directions for future public health actions. [ABSTRACT FROM AUTHOR]

Background: One of the most prevalent bacterial infections in children is urinary tract infection (UTI), which has become a major concern with increasing resistance of the pathogens to the routinely used antimicrobial agents. The aim of the study is to determine the antimicrobial susceptibility patterns of pediatric UTI-causing pathogens, including ESBL-producing bacteria, in Saudi Arabia. Methods: This cross-sectional retrospective study was conducted to ascertain the frequency of isolation and the antimicrobial resistance pattern of uropathogens among children aged 0–15 years. The data from the urine cultures was collected during 2019–2020 at the King Fahad Medical City, a major tertiary hospital in Riyadh, Saudi Arabia. A total of 1022 urine samples from patients diagnosed with urinary tract infections (UTIs) were collected for this study. Microbial species present in the samples were cultured and identified using standard biochemical techniques. To assess the resistance of these strains to antimicrobial drugs, an in vitro method was employed, and the criteria set by the Clinical Laboratory Standard Institute (CLSI) were followed. In addition, a double-disc synergy test was conducted to identify strains of E. coli that produce extended-spectrum beta-lactamase (ESBL). Results: The predominant pathogens were E. coli (58.6%), followed by Klebsiella sp. (23.9%). E. coli isolates were more sensitive to meropenem and ertapenem in 99.2% of cases, followed by amikacin (99%). Klebsiella sp. were sensitive to amikacin in 97.1% of cases, followed by meropenem and ertapenem (92.2% in both). The highest sensitivities of antimicrobials toward ESBL were for meropenem and ertapenem (100% in both), followed by amikacin (99%). Conclusions: Our study recommends using local antibiotic sensitivity data for empirical UTI treatment. Amikacin, ertapenem, and meropenem are effective intravenous options. Cephalosporin, cefuroxime, amoxicillin/clavulanic acid, and nitrofurantoin are suitable oral choices. No significant changes in antimicrobial susceptibility were observed during the COVID-19 pandemic. Further research is needed to assess potential pandemic-related alterations. [ABSTRACT FROM AUTHOR]

Renewable energy is considered to be sustainable solution to the energy crisis and climate change. The transition to renewable energy needs to be considered on a sectoral basis and one such sector that can potentially decarbonized with renewable energy is the telecommunication sector. Several base transceiver stations (BTS) in remote regions have unstable electric supply systems. Diesel generators (DG) are a common solution to energy problems on such telecommunication sites. However, they have high fuel costs on the global market and contribute to high carbon emissions. Hybrid renewable energy systems may provide a stable power output by integrating multiple energy sources, essential for supplying a dependable and uninterrupted power supply in the context of the telecom sector, notably base transceiver stations (BTS). Deploying such a system might also help BTS, which relies mainly on diesel generators with battery storage backup, reduce operational costs and environmental problems. This study presents the framework for large-scale photovoltaic system penetration based on techno-economic analysis (based on actual on ground data with least assumptions) in base transceiver stations (BTS) encapsulating telecom sector spread across various geographical regions. The proposed framework includes a mathematical model complemented with system design in HOMER software tool. The techno-economic aspects of the study were spread across 2, 12 and 263 sites, along with comparison analysis of photovoltaic system installation with and without energy storage devices, respectively. The sites included both on-grid and off-grid sites, which were exposed to high levels of power outages and subjected to reliance on costly and environmentally hazardous diesel generators. Optimization results showed that the photovoltaic system with a diesel generator and battery storage system provide a promising solution to the energy problem, with an average decrease in LCOE of 29%, DG hour's reduction by 82% with 92% reduction in carbon emission and a reduction in NPC of 34% due to the high availability of solar. The techno-economic analysis indicated that optimized photovoltaic system and storage results in both on–off grid BTS sites with better options, amid low cost of energy and free accessibility of solar. Moreover, the results spread across geographical regions aiming at a reliable and environmentally friendly option that reduces load on utility grid across on-grid BTS sites and substantial overall reduction in diesel usage. [ABSTRACT FROM AUTHOR]

In this work, the solvothermal solidification method has been used to be prepared as a homogenous CuSn-organic nano-composite (CuSn-OC) to use as a catalyst for alkaline water electrolysis for cost-effective H2 generation. FT-IR, XRD, and SEM techniques were used to characterize the CuSn-OC which confirmed the formation of CuSn-OC with a terephthalic acid linker as well as Cu-OC and Sn-OC. The electrochemical investigation of CuSn-OC onto a glassy carbon electrode (GCE) was evaluated using the cyclic voltammetry (CV) method in 0.1 M KOH at room temperature. The thermal stability was examined using TGA methods, and the Cu-OC recorded a 91.4% weight loss after 800 °C whereas the Sn-OC and CuSn-OC recorded 16.5 and 62.4%, respectively. The results of the electroactive surface area (ECSA) were 0.5, 0.42, and 0.33 m2 g−1 for the CuSn-OC, Cu-OC, and Sn-OC, respectively, and the onset potentials for HER were −420, −900, and −430 mV vs. the RHE for the Cu-OC, Sn-OC, and CuSn-OC, respectively. LSV was used to evaluate the electrode kinetics, and the Tafel slope for the bimetallic catalyst CuSn-OC was 190 mV dec−1, which was less than for both the monometallic catalysts, Cu-OC and Sn-OC, while the overpotential was −0.7 vs. the RHE at a current density of −10 mA cm−2. [ABSTRACT FROM AUTHOR]

Distribution networks have entered a new era with the broad adoption of the distributed generation (DG) allocation as a practical solution for addressing power losses, voltage variation, and voltage stability. The primary goal is to enhance techno-economic and environmental characteristics while meeting the limitations of the system. In order to allocate DGs in active distribution networks (ADNs) efficiently, this study demonstrates two optimization methods inspired by nature: ant lion optimization (ALO) and multiverse optimization (MVO). Various multi-criteria decision-making (MCDM) methods are used to find the best possible solution among the different alternatives. On the IEEE 33- and 69-bus active distribution networks, the proposed ALO was shown to be effective and produces the highest loss reduction in the IEEE 33- and 69-bus systems at 94.43% and 97.16%, respectively, and the maximum voltage stability index (VSI) was 0.9805 p.u and 0.9937 p.u, respectively; moreover, the minimum voltage deviation (VD) and annual energy loss cost for the given test systems was 0.00019 p.u and 3353.3 PKR, which shows that the suggested method can produce higher quality results as compared to other methods presented in the literature. Therefore, the proposed ALO is a very efficient, effective, and appealing solution to the optimal allocation of the distributed generation (OADG) problem. [ABSTRACT FROM AUTHOR]

Diagnostically, vertical root fractures (VRFs) can be a frustrating experience for the dentist. Misdiagnosis could result in significant time and effort losses involved in erroneously intervening endodontically and/or periodontally. Certainly, diagnosing VRFs is often very difficult, and diagnoses based on speculations have led to the extraction of many salvageable teeth. This study was conducted in the radiology unit of College of Dentistry, Prince Sattam bin Abdulaziz University, between December 2021 and June 2022 to evaluate the ability to detect VRFs following the use of a novel radio-opaque dye using periapical radiographs (PARs) and cone-beam computed tomography (CBCT). After carefully inducing VRFs on extracted, single-rooted, virgin premolars (n = 26), they were assigned to control (n = 2) and experimental groups (n = 24). The fracture site of the tooth in the control group received methylene blue dye, whereas the experimental group received a novel dye. Two differently angled PARs were obtained for all the teeth, followed by a CBCT image. Three blinded investigators participated in scoring a Likert scale form with a set of questions. Inter-/intra-examiner reliability showed excellent consistency using Cronbach's alpha test. The Z-test revealed CBCT and PAR to be equally adept at detecting VRFs, with the mean values showing no statistically significant differences. The extent of the VRFs and dye penetration were significantly better when angled radiographs and axial view CBCT were evaluated. Within the limitations of this study, the dye tested showed promising initial results as an aid in radiographically detecting VRFs. The use of such minimally invasive methods is critically needed for diagnosing and managing VRFs. However, further testing should be performed prior to its clinical use. [ABSTRACT FROM AUTHOR]

Electrical grids are one of the major sources of emissions of greenhouse gases (GHG), which are harmful to the environment because they contribute to global warming. As the geographical, environmental, political, and policy constraints are different, policies and research frameworks from developed countries cannot be used directly in developing countries. This paper suggests a completely integrated quantification approach (IQA) and sub-methodologies, such as SM1, SM2, and SM3, that consider the limitations, evaluates the effects, and suggest a way to deal with climate change problems on the power grid. From the perspective of renewable energy (RE) integration and GHG emissions (mainly CO2), the proposed approach addresses the limitations in the policy framework extending to 2030. In addition, the effects of the changes in the ambient temperature, from 0.5 °C to 2 °C, have been examined for thermal power generation and transformers. Lastly, the proposed method considers how energy-efficient devices (EEDs) affect the residential load sector. The results show that households used 10.7% less energy and their costs decreased significantly. This work's quantitative approach gives a specific way to reduce the carbon footprint of the electrical grid. [ABSTRACT FROM AUTHOR]

Heat loss through the building envelope comprises air leaks through the cracks and largely through the windows, which is the weakest link of the thermal envelope. Therefore, it is necessary to devise a systematic approach to analyze the rightful selection of glass for buildings. The investigation is to analyze the energy-saving potential of different glasses and their comparisons to the initial capital cost to find the payback time in terms of energy saving by using two different types of equipment. The quantitative simulation study was completed on the Hourly Analysis Program (HAP) to analyze the annual energy consumption of the HVAC system for seven glasses and two types of chilled water equipment. The results show that the performance glasses with a tint had better efficiency in terms of energy saving, with a payback time of 3–7 months. A comparison of all glasses illustrated that float glass contributes the most to the total cooling load among all glasses, which were 5.04%, 5.7%, 7.6%, and 8.9% for the N, S, E, and W orientations, respectively. Moreover, the lowest contribution of glass to the total cooling load was given by tinted double-glazed glass, which was 2%, 2.3%, 3.0%, and 3.01% for N, S, E, and W orientations, respectively. [ABSTRACT FROM AUTHOR]

Pakistan is an energy deficient country with depleting energy reserves and increasing energy demand. Due to excessive population growth, the domestic and commercial energy sectors are experiencing rising demand. To meet the requisite demand, renewables are favored rather than conventional counterparts. In this study, we model hybrid power systems using solar, wind and biomass resources for electrifying remote areas. The four locations are chosen for the study around a developing country, Pakistan, where each site is designed according to an isolated microgrid with maximum indigenous resources potential as per the requisite demands. A survey is conducted for the load demand and biomass availability. Optimization is conducted across objectives of minimum levelized cost of the generated energy, least the net present cost and lesser payback period. The optimal results were achieved in-terms of required objectives across southern sites as compared to northern counterparts. The cost of generated energy is comparable to grid electricity and ensures 24 h power supply without cut off and load shedding to the un-electrified rural area. The hybrid power system has a low carbon footprint across emissions due to the use of renewable resources. All the estimated load of rural communities is met with the available resources and mid-career impact has also been conducted across 10 years of the project life to fulfill the increasing load demand of the communities after installation. The results are validated via comparative analysis and show the effectiveness of the proposed study. [ABSTRACT FROM AUTHOR]

The concept of microgrids has emerged as an effective way to integrate distributed energy resources (DERs) into distribution networks. The presence of DERs in microgrids leads to challenges in the formulation of protection for microgrids. Protection problems arise in a microgrid due to varying fault current levels in different operating scenarios. In order to overcome the practical challenges arising from varying fault current levels leading to short-circuit faults in microgrids, this paper proposes a MagnetoResistive (MR) sensors-based protection scheme, with fault localization through SuperimposedReactiveEnergy (SRE). The process is initiated by employing highly sensitive non-intrusive magnetic sensors to detect the magnetic field at each end of the distribution line. The magnetic field is then used to calculate the total harmonic distortion and thus detect faults in microgrids. After detection of faults, the proposed scheme uses SRE to identify faulty zones in microgrids. Finally, SI components of the current are extracted for fault classification. Extensive simulations on the International Electro-technical Commission (IEC) microgrid are performed in MATLAB/Simulink to validate the efficacy of the proposed scheme. Simulation results show that the proposed scheme can effectively detect, classify and isolate different faults in microgrids, while operating under various modes with varying fault locations and resistances, with the efficiency of approximately 97–98%. [ABSTRACT FROM AUTHOR]

Energy planning has become more complicated in the 21st century of sustainable development due to the inclusion of numerous standards such as techno-economic, and environmental considerations. This paper proposes multi-criteria sustainable planning (MCSP) based optimization approach for identifying DGs' optimal allocations and rating powers. The main objectives of this paper are the reduction of the network's total power loss, voltage profile improvement, energy loss saving maximization, and curtailing environmental emissions and water consumption to achieve Sustainable Development Goals (SDGs 3, 6, 7, 13, and 15) by taking the constraints into consideration. Different alternatives are evaluated across four aspects of performance indices; technical, cost-economic, environmental, and social (TEES). In terms of TEES performance evaluations, various multi-criteria decision-making (MCDM) approaches are used to determine the optimal trade-off among the available solutions. These methods are gaining wide acceptance due to their flexibility while considering all criteria and objectives concurrently. Annual energy loss saving is increased by 97.13%, voltage profile is improved to 0.9943 (p.u), and emissions are reduced by 82.45% using the proposed technique. The numerical results of the proposed MCSP approach are compared to previously published works to validate and may be used by researchers and energy planners as a planning tool for ADN schemes. [ABSTRACT FROM AUTHOR]

To enhance the reliability and resilience of power systems and achieve reliable delivery of power to end users, smart distribution networks (SDNs) play a vital role. The conventional distribution network is transforming into an active one by incorporating a higher degree of automation. Replacing the traditional absence of manual actions, energy delivery is becoming increasingly dependent on intelligent active system management. As an emerging grid modernization concept, the smart grid addresses a wide range of economic and environmental concerns, especially by integrating a wide range of active technologies at distribution level. At the same time, these active technologies are causing a slew of technological problems in terms of power quality and stability. The development of such strategies and approaches that can improve SDN infrastructure in terms of planning, operation, and control has always been essential. As a result, a substantial number of studies have been conducted in these areas over the last 10–15 years. The current literature lacks a combined systematic analysis of the planning, operation, and control of SDN technologies. This paper conducts a systematic survey of the state-of-the-art advancements in SDN planning, operation, and control over the last 10 years. The reviewed literature is structured so that each SDN technology is discussed sequentially from the viewpoints of planning, operation, and then control. A comprehensive analysis of practical SND concepts across the globe is also presented in later sections. The key constraints and future research opportunities in the existing literature are discussed in the final part. This review specifically assists readers in comprehending current trends in SDN planning, operation, and control, as well as identifying the need for further research to contribute to the field. [ABSTRACT FROM AUTHOR]

There are three main parts of an electric power system—power generation, transmission, and distribution. For electric companies, it is a tough challenge to reduce losses of the power system and deliver lossless and reliable power from the generating station to the consumer end. Nowadays, modern power systems are more complex due to gradually increasing loads. In the electrical power system, especially in transmission and distribution networks, there are power losses due to many reasons such as overloading of the line, long distribution lines, low power factors, corona losses, and unsuitable conductor size. The main performance factor of the power system is reliability. Reliability means continuity of the power supply without any interruptions from the generating station to the demand side. Thus, due to these power losses, there are voltage stability problems and economic losses in the electrical system. The voltage stability of the power system can be increased by improving the voltage profile. In this paper, different techniques are analyzed that include the integration of wind power, the integration of photovoltaic power, and reactive power injection by integrating FACTS devices. These techniques are applied to the IEEE 57 bus system with standard data using simulation models developed in MATLAB. Thus, the results of the analysis of these techniques have been compared with each other. [ABSTRACT FROM AUTHOR]

Dynamics in rainfall patterns due to climate change are posing a threat to crop production globally. The core issue of food security is expected to intensify, and improving crop yield using motorized power irrigation mechanisms can help in curtailing the impact of drought and changing weather patterns to meet the crop water requirement. To meet the energy demand of irrigation systems, this paper explores the use of hybrid energy sources, i.e., wind and solar energy, taking Shaqra Saudi Arabia as case study. This paper presents a systematic case study that evaluates crop water requirements for 3 different crops using the United Nations Food and Agriculture Organization's software CROPWAT 8.0 and converts the water requirement into energy demand to design the water pumping system. The energy requirement water pumping system is used to design a hybrid energy system using HOMER PRO 3.14.4 that can reliably meet the energy demand. The results suggests that, contrary to the common consideration in Saudi Arabia, a hybrid of wind and solar energy proves to be more cost effective and yields a higher amount of energy. The results suggest that a significant reduction in cost can be achieved with a hybrid energy system as compared to a solar PV system only. [ABSTRACT FROM AUTHOR]

This paper deals with an energy management problem to ensure the best performance of the recharging tools used in electric vehicles. The main objective of this work is to find the optimal condition for controlling a hybrid recharging system by regrouping the photovoltaic cells and fuel cells. The photovoltaic and fuel cell systems were connected in parallel via two converters to feed either a lithium battery bank or the main traction motor. This combination of energy sources resulted in a hybrid recharging system. The mathematical model of the overall recharging system and the designed power management loop was developed, taking into account multiple aspects, including vehicle loading, the stepwise mathematical modelling of each component, and a detailed discussion of the required electronic equipment. Finally, a simplistic management loop was designed and implemented. Multiple case studies were simulated, statistical approaches were used to quantify the contribution of each recharging method, and the benefits of the combination of the two sources were evaluated. The energetic performance of an electric vehicle with the proposed hybrid recharging tool under various conditions, including static and dynamic modes, was simulated using the MATLAB/Simulink tool. The results suggest that despite the additional weight of PV panels, the combination of the PV and FC systems improves the vehicle's energetic performance and provides a higher charging capacity instead of using an FC alone. A comparison with similar studies revealed that the proposed model has a higher efficiency. Finally, the benefits and drawbacks of each solution are discussed to emphasise the significance of the hybrid recharging system. [ABSTRACT FROM AUTHOR]

Repowering a wind farm enhances its ability to generate electricity, allowing it to better utilize areas with high mean wind speeds. Pakistan's present energy dilemma is a serious impediment to its economic development. The usage of a diesel generator as a dependable backup power source raises the cost of energy per kWh and increases environmental emissions. To minimize environmental emissions, grid-connected wind farms enhance the percentage of wind energy in the electricity system. These wind generators' effects, on the other hand, are augmented by the absorption of greater quantities of reactive electricity from the grid. According to respective grid codes, integration of commercial onshore Large-Scale Wind Farms (LSWF) into a national grid is fraught with technical problems and inter-farm wake effects, which primarily ensure power quality while degrading overall system operation and limiting the optimal use of attainable wind resources. The goal of this study is to examine and estimate the techno-economic influence of large-scale wind farms linked to poor transmission systems in Pakistan, contemplating the inter-farm wake effect and reactive power diminution and compensating using a range of voltage-ampere reactive (VAR) devices. This study presents a partial repowering technique to address active power deficits produced by the wake effect by raising hub height by 20 m, which contributed to recovering the active power deficit to 48% and so reduced the effects of upstream wind farms. Simulations were conducted for several scenarios on an actual test system modeled in MATLAB for comparative study using capacitor banks and different flexible alternating current transmission system (FACTS) devices. Using the SAM (System Advisor Model) and RETscreen, a complete technical, economic, and environmental study was done based on energy fed into the grid, payback time, net present value (NPV), and greenhouse gases (GHG) emission reduction. The studies suggest that the unified power flow controller (UPFC) is the optimum compensating device via comparison analysis as it improved the power handling capabilities of the power system. Our best-case scenario includes UPFC with hub height augmentation, demonstrating that it is technically, fiscally, and environmentally viable. Over the course of its lifespan, the planned system has the potential to save 1,011,957 tCO2, resulting in a greener environment. When the energy generated annually by a current wake-affected system is compared to our best-recommended scenario, a recovered shortfall of 4.851% is seen, with improved system stability. This modest investment in repowering boosts energy production due to wake effects, resulting in increased NPV, revenue, and fewer CO2 footprints. [ABSTRACT FROM AUTHOR]

In addition to zero-carbon generation, the plummeting cost of renewable energy sources (RES) is enabling the increased use of distributed-generation sources. Although the RES appear to be a cheaper source of energy, without the appropriate design of the RES with a true understanding of the nature of the load, they can be an unreliable and expensive source of energy. Limited research has been aimed at designing small-scale hybrid energy systems for irrigation pumping systems, and these studies did not quantify the water requirement, or in turn the energy required to supply the irrigation water. This paper provides a comprehensive feasibility analysis of an off-grid hybrid renewable energy system for the design of a water-pumping system for irrigation applications in Sudan. A systematic and holistic framework combined with a techno-economic optimization analysis for the planning and design of hybrid renewable energy systems for small-scale irrigation water-pumping systems is presented. Different hybridization cases of solar photovoltaic, wind turbine and battery storage at 12 different sites in Sudan are simulated, evaluated, and compared, considering the crop water requirement for different crops, the borehole depth, and the stochasticity of renewable energy resources. Soil, weather, and climatic data from 12 different sites in Sudan were used for the case studies, with the key aim to find the most robust and reliable solution with the lowest system cost. The results of the case studies suggest that the selection of the system is highly dependent on the cost, the volatility of the wind speed, solar radiation, and the size of the system; at present, hybridization is not the primary option at most of sites, with the exception of two. However, with the reduction in price of wind technology, the possibility of hybrid generation will rise. [ABSTRACT FROM AUTHOR]

In addition to zero-carbon generation, the plummeting cost of renewable energy sources (RES) is enabling the increased use of distributed-generation sources. Although the RES appear to be a cheaper source of energy, without the appropriate design of the RES with a true understanding of the nature of the load, they can be an unreliable and expensive source of energy. Limited research has been aimed at designing small-scale hybrid energy systems for irrigation pumping systems, and these studies did not quantify the water requirement, or in turn the energy required to supply the irrigation water. This paper provides a comprehensive feasibility analysis of an off-grid hybrid renewable energy system for the design of a water-pumping system for irrigation applications in Sudan. A systematic and holistic framework combined with a techno-economic optimization analysis for the planning and design of hybrid renewable energy systems for small-scale irrigation water-pumping systems is presented. Different hybridization cases of solar photovoltaic, wind turbine and battery storage at 12 different sites in Sudan are simulated, evaluated, and compared, considering the crop water requirement for different crops, the borehole depth, and the stochasticity of renewable energy resources. Soil, weather, and climatic data from 12 different sites in Sudan were used for the case studies, with the key aim to find the most robust and reliable solution with the lowest system cost. The results of the case studies suggest that the selection of the system is highly dependent on the cost, the volatility of the wind speed, solar radiation, and the size of the system; at present, hybridization is not the primary option at most of sites, with the exception of two. However, with the reduction in price of wind technology, the possibility of hybrid generation will rise., Competing Interests: Conflicts of InterestThe authors declare no conflict of interest., (© 2021 by the authors.)