Search

Based on the nonlinear relationship between heart rate and stroke volume, a flow model of left ventricular circulation was improved, and a variable-speed blood-pump control strategy based on heart-rate feedback was proposed. The control strategy was implemented on a system combining the rotary blood pump and blood circulation models of heart failure. The aortic flow of a healthy heart at different heart rates was the desired control goal. Changes in heart rate were monitored and pump speed was adjusted so that the output flow and aortic pressure of the system would match a normal heart in real time to achieve the best auxiliary state. After simulation with MATLAB, the cardiac output satisfied the ideal perfusion requirements at different heart rates, and aortic pressure demonstrated lifting and had good pulsatile performance when a variable-speed blood pump was used. The coupled model reflected the relationship between hemodynamic parameters at different heart rates with the use of the variable-speed blood pump, providing a theoretical basis for the blood-pump-assisted treatment of heart failure and the design of physiological control strategies. [ABSTRACT FROM AUTHOR]

Physical education teachers need valid, low-cost, subjective techniques as an alternative to high-cost new technologies to monitor students' intensity monitoring. This study aimed to investigate the correlations between both objective and subjective external (eTL) and internal (iTL) intensities. A total of 95 primary education students participated in this study. In this regard, 40 played soccer, and 55 performed basketball tasks, recording a total of 3956 units of analysis. The intensities caused by the different soccer and basketball tasks were measured using objective techniques (inertial devices and heart rate monitors) and subjective techniques (a sheet of task analysis and ratings of perceived exertion). Matrix scatter plots were made to show the values of two variables for a dataset. In this regard, adjustment lines were plotted to determine the trend of the correlations. Then, Spearman's correlation was calculated to measure the association between two variables. Despite the low correlation levels obtained, the main results showed significant positive correlations between the intensities. This means that the high intensity values recorded by objective techniques also implied high intensity values recorded by subjective techniques, and vice versa. Negative correlations (r Rho = −0.19; p = 0.00) were only found between the following eTL variables: task eTL per minute (subjective technique) and player load per minute (objective technique). This negative correlation occurred when students played in the same 3 vs. 3 game situation without variability in subjective eTL (M ± SD, 28.00 ± 0.00). Therefore, subjective eTL and iTL techniques could be proposed as a suitable alternative for planning and monitoring the intensities supported by students in physical education classes. Moreover, these subjective techniques are easy to use in schools. [ABSTRACT FROM AUTHOR]

Conventional personal identification methods (ID, password, authorization certificate, etc.) entail various issues, including forgery or loss. Technological advances and the diffusion across industries have enhanced convenience; however, privacy risks due to security attacks are increasing. Hence, personal identification based on biometrics such as the face, iris, fingerprints, and veins has been used widely. However, biometric information including faces and fingerprints is difficult to apply in industries requiring high-level security, owing to tampering or forgery risks and recognition errors. This paper proposes a personal identification technique based on an ensemble of long short-term memory (LSTM) and convolutional neural network (CNN) that uses electrocardiograms (ECGs). An ECG uses internal biometric information, representing the heart rate in signals using microcurrents and thereby including noises during measurements. This noise is removed using filters in a preprocessing step, and the signals are divided into cycles with respect to R-peaks for extracting features. LSTM is used to perform personal identification using ECG signals; 1D ECG signals are transformed into the time–frequency domain using STFT, scalogram, FSST, and WSST; and a 2D-CNN is used to perform personal identification. This ensemble of two models is used to attain higher performances than LSTM or 2D-CNN. Results reveal a performance improvement of 1.06–3.75%. [ABSTRACT FROM AUTHOR]

The measurement of heartbeat rate and breathing rate for patients with sensitive skin, such as skin with burns, is very difficult to do, especially if the number of patients is large and medical personnel is limited. Therefore, this study seeks to propose a preliminary solution to this problem by proposing a device that can measure the vital signs of several people concurrently, especially the heartbeat rate and breathing rate, without attaching sensors to their skin. This is done using an FMCW (frequency-modulated continuous wave) radar that operates at 77–81 GHz. FMCW radar emits electromagnetic waves towards the chest of several targets and picks up the reflected waves. Then, using signal processing of these reflected waves, each target's heartbeat rate and breathing rate can be obtained. Our experiment managed to perform concurrent detection for four targets. The experimental results are between 52 and 82 beats per minute for the heartbeat rates and between 10 and 35 breaths per minute for the breathing rates of four targets. These results are in accordance with normal heartbeat rate and normal breathing rate; thus, our research succeeded in proposing a preliminary solution to this problem. [ABSTRACT FROM AUTHOR]

Healthcare is an indispensable part of human life and chronic illnesses like cardiovascular diseases (CVD) have a deeply negative impact on the healthcare sector. Since the ever-growing population of chronic patients cannot be managed at hospitals, therefore, there is an urgent need for periodic monitoring of vital parameters and apposite treatment of these patients. In this paper, an Internet of Medical Things (IoMT) -based remote patient monitoring system is proposed which is based on Artificial Intelligence (AI) and edge computing. The primary focus of this paper is to develop an embedded prototype that can be used for remote monitoring of cardiovascular patients. The system will continuously monitor physiological parameters like body temperature, heart rate, and blood oxygen saturation, and then report the health status to the authenticated users. The system employs edge computing to perform multiple functionalities including health status inference using a Machine Learning (ML) model which makes predictions on real-time data, alert notifications in case of an emergency, and transferring data between the sensor network and the cloud. A web-based application is developed for the depiction of raw data and ML results and to provide a direct communication channel between the patient and the doctor. The ML module achieved an accuracy of 96.26% on the test set using the K-Nearest Neighbors (KNNs) algorithm. This solution aims to address the sense of emergency due to the alarming statistics that highlight the mortality rate of cardiovascular patients. The project will enable a smart option based on IoT and ML to improve standards of living and prove crucial in saving human lives. [ABSTRACT FROM AUTHOR]

Biomedical sensors help patients monitor their health conditions and receive assistance anywhere and at any time. However, the limited battery capacity of medical devices limits their functionality. One advantageous method to tackle this limited-capacity issue is to employ the wireless power transfer (WPT) technique. In this paper, a WPT technique using a magnetic resonance coupling (MRC-WPT)-based wireless heart rate (WHR) monitoring system--which continuously records the heart rate of patients--has been designed, and its efficiency is confirmed through real-time implementation. The MRC-WPT involves three main units: the transmitter, receiver, and observing units. In this research, a new design of spiral-spider coil was designed and implemented for transmitter and receiver units, respectively, to supply the measurement unit, which includes a heart rate sensor, microcontroller, and wireless protocol (nRF24L01) with the operating voltage. The experimental results found that an adequate voltage of 5 V was achieved by the power component to operate the measurement unit at a 20 cm air gap between the receiver and transmitter coils. Further, the measurement accuracy of the WHR was 99.65% comparative to the benchmark (BM) instrument. Moreover, the measurements of the WHR were validated based on statistical analyses. The results of this study are superior to those of leading works in terms of measurement accuracy, power transfer, and Transfer efficiency. [ABSTRACT FROM AUTHOR]

Recently, UWB imaging has also been applied to brain stroke classification, bone imaging, and lung cancer detection. Dedicated machine learning approaches were also employed in [[2]] to differentiate between different human emotions (such as happiness, disgust, and fear) using UWB impulse-radar data (without placing any on-body sensors), reaching an accuracy of 76%. The extremely low power transmission levels of ultra-wideband (UWB) technology, alongside its advantageously large bandwidth, make it a prime candidate for being used in numerous healthcare scenarios, which require short-range high-data-rate communications and safe radar-based applications. [Extracted from the article]

To achieve sensitivity, comfort, and durability in vital sign monitoring, this study explores the use of radar technologies in wearable devices. The study first detected the respiratory rates and heart rates of a subject at a one-meter distance using a self-injection-locked (SIL) radar and a conventional continuous-wave (CW) radar to compare the sensitivity versus power consumption between the two radars. Then, a pulse rate monitor was constructed based on a bistatic SIL radar architecture. This monitor uses an active antenna that is composed of a SIL oscillator (SILO) and a patch antenna. When attached to a band worn on the subject's wrist, the active antenna can monitor the pulse on the subject's wrist by modulating the SILO with the associated Doppler signal. Subsequently, the SILO's output signal is received and demodulated by a remote frequency discriminator to obtain the pulse rate information. [ABSTRACT FROM AUTHOR]

Respiratory and heart rates are among the most important physiological parameters used to monitor patients' health. It is important to design devices that can measure these parameters without risking or altering the subject's health. In this context, a novel sensing method to monitor simultaneously the heartbeat and respiratory rate signals of patients within an electrically safety environment was developed and tested. An optical fiber-based sensor was used in order to detect two optical phenomena. Photo-plethysmography and the relation between bending radius and attenuation of optical fiber were coupled through a single beam light traveling along this fiber. [ABSTRACT FROM AUTHOR]

Since its inception in 2013, Bluetooth Low Energy (BLE) has become the standard for short-distance wireless communication in many consumer devices, as well as special-purpose devices. In this study, we analyze the security features available in Bluetooth LE standards and evaluate the features implemented in two BLE wearable devices (a Fitbit heart rate wristband and a Polar heart rate chest wearable) and a BLE keyboard to explore which security features in the BLE standards are implemented in the devices. In this study, we used the ComProbe Bluetooth Protocol Analyzer, along with the ComProbe software to capture the BLE traffic of these three devices. We found that even though the standards provide security mechanisms, because the Bluetooth Special Interest Group does not require that manufacturers fully comply with the standards, some manufacturers fail to implement proper security mechanisms. The circumvention of security in Bluetooth devices could leak private data that could be exploited by rogue actors/hackers, thus creating security, privacy, and, possibly, safety issues for consumers and the public. We propose the design of a Bluetooth Security Facts Label (BSFL) to be included on a Bluetooth/BLE enabled device's commercial packaging and conclude that there should be better mechanisms for informing users about the security and privacy provisions of the devices they acquire and use and to educate the public on protection of their privacy when buying a connected device. [ABSTRACT FROM AUTHOR]

Currently, old-style personal Medicare techniques rely mostly on traditional methods, such as cumbersome tools and complicated processes, which can be time consuming and inconvenient in some circumstances. Furthermore, such old methods need the use of heavy equipment, blood draws, and traditional bench-top testing procedures. Invasive ways of acquiring test samples can potentially cause patient discomfort and anguish. Wearable sensors, on the other hand, may be attached to numerous body areas to capture diverse biochemical and physiological characteristics as a developing analytical tool. Physical, chemical, and biological data transferred via the skin are used to monitor health in various circumstances. Wearable sensors can assess the aberrant conditions of the physical or chemical components of the human body in real time, exposing the body state in time, thanks to unintrusive sampling and high accuracy. Most commercially available wearable gadgets are mechanically hard components attached to bands and worn on the wrist, with form factors ultimately constrained by the size and weight of the batteries required for the power supply. Basic physiological signals comprise a lot of health-related data. The estimation of critical physiological characteristics, such as pulse inconstancy or variability using photoplethysmography (PPG) and oxygen saturation in arterial blood using pulse oximetry, is possible by utilizing an analysis of the pulsatile component of the bloodstream. Wearable gadgets with "skin-like" qualities are a new type of automation that is only starting to make its way out of research labs and into pre-commercial prototypes. Flexible skin-like sensing devices have accomplished several functionalities previously inaccessible for typical sensing devices due to their deformability, lightness, portability, and flexibility. In this paper, we studied the recent advancement in battery-powered wearable sensors established on optical phenomena and skin-like battery-free sensors, which brings a breakthrough in wearable sensing automation. [ABSTRACT FROM AUTHOR]

Simple Summary: Search and rescue (SAR) dogs are irreplaceable support in natural disasters. Not only are these animals required to have optimal scenting capabilities, but they are also required to have excellent physical conditions. Implementing protocols to monitor their fitness would help to optimize their performance and welfare. This study evaluated heart rate (HR) changes in avalanche SAR dogs and handlers during a 5.5 km endurance exercise in the snow, at an altitude of approximately 2000 m.a.s.l., reflecting their usual working and workload conditions. Dogs' and handlers' HR and activities were monitored by a global positioning satellite (GPS)/HR system. Factors influencing dogs' and handlers' HR changes and their possible correlation were investigated. As expected, the dog's HR changes during the endurance activity were affected by speed, gradient, altitude, and time. The handlers' HR changes differed and were not correlated with those recorded in the dogs. Thus, SAR handlers may not perceive the physical stress of their dog in real-time. Findings indicate that GPS/HR monitoring systems could be utilized in field conditions for monitoring SAR units' physical fitness. A "fitness index" could be developed by incorporating HR and velocity measurements in order to target training strategies and indicate risk factors for physical distress in working dogs. This study aimed to assess the heart rate (HR) responses of avalanche SAR dogs and handlers under working field conditions. Thirteen SAR units (dogs and handlers) performed an exercise (Endurance) consisting of approximately 5.5 km of rough tracks through deep snow, at an altitude of 1991–2250 m.a.s.l. The exercise was repeated twice for each of the two different tracks. Both handlers and dogs were equipped with a global positioning satellite/heart rate (GPS/HR) system (Polar®). Multivariable models were used to evaluate the effects of environmental (i.e., gradient, altitude, track, and time) and intrinsic (i.e., speed, repetition, and breed) factors on changes from baseline HR (Δ%HR). The dog's Δ%HR was greater in the flat and uphill compared with downhill, and increased progressively as the speed increased (p < 0.001). Moreover, it rose at altitudes above 2100 m.a.s.l. and peaked after 30 min of the Endurance activity (p < 0.01). These findings indicated that HR monitors could be a valuable tool to contribute to the evaluation of avalanche dogs' fitness in their real working environment. In contrast, the lack of correlation between the dogs' and handlers' HR changes suggests that handlers might not perceive the physical conditions of their dog in real-time. Thus, implementing protocols to monitor avalanche SAR dogs' fitness using a GPS/HR monitoring system could help handlers to tailor the training and workload and to detect the risk factors for physical distress of working dogs. [ABSTRACT FROM AUTHOR]

Due to the improvement of living standards, people's attention to health has gradually increased. More and more people are willing to spend money and time on health management. This article reviews work on the vital signs monitoring system based on fiber optic interferometers, including the design of sensor structures, signal demodulation methods and data analysis. After a large number of trials, the system can achieve long-term stable heart rate (HR), respiration rate (RR) and body temperature monitoring, and the collected data can be used for health analysis. Due to the high sensitivity, low cost, and light weight of the interferometric fiber optic sensor, it can be integrated under a mattress or a cushion, which is very suitable for daily use. The system has great application prospects in the field of healthcare. [ABSTRACT FROM AUTHOR]

Due to the recent COVID-19 pandemic, many people have faced in-home isolation, as every suspected patient must stay at home. The behavior of such isolated people needs to be monitored to ensure that they are staying at home. Using a camera is a very practical method. However, smart bracelets are more convenient when personal privacy is a concern or when the blood oxygen value or heart rate must be monitored. In this study, a low-cost indoor positioning system that uses a Bluetooth beacon, a smart bracelet, and an embedded system is proposed. In addition to monitoring whether a person living alone is active in a specific environment and tracking the heart rate or blood oxygen value under particular conditions, this system can also send early warning signals to specific observation units or relatives through instant messaging software. [ABSTRACT FROM AUTHOR]

Recently, wet-bulb globe temperature (WBGT) has attracted a lot of attention as a useful index for measuring heat strokes even when core body temperature cannot be available for the prevention. However, because the WBGT is only valid in the vicinity of the WBGT meter, the actual ambient heat could be different even in the same room owing to ventilation, clothes, and body size, especially in hot specific occupational environments. To realize reliable heat stroke prevention in hot working places, we proposed a new personalized vital sign index, which is combined with several types of vital data, including the personalized heat strain temperature (pHST) index based on the temperature/humidity measurement to adjust the WBGT at the individual level. In this study, a wearable device was equipped with the proposed pHST meter, a heart rate monitor, and an accelerometer. Additionally, supervised machine learning based on the proposed personalized vital index was introduced to improve the prevention accuracy. Our developed system with the proposed vital sign index achieved a prevention accuracy of 85.2% in a hot occupational experiment in the summer season, where the true positive rate and true negative rate were 96.3% and 83.7%, respectively. [ABSTRACT FROM AUTHOR]

This paper presents an algorithm for real-time detection of the heart rate measured on a person's wrist using a wearable device with a photoplethysmographic (PPG) sensor and accelerometer. The proposed algorithm consists of an appropriately trained LSTM network and the Time-Domain Heart Rate (TDHR) algorithm for peak detection in the PPG waveform. The Long Short-Term Memory (LSTM) network uses the signals from the accelerometer to improve the shape of the PPG input signal in a time domain that is distorted by body movements. Multiple variants of the LSTM network have been evaluated, including taking their complexity and computational cost into consideration. Adding the LSTM network caused additional computational effort, but the performance results of the whole algorithm are much better, outperforming the other algorithms from the literature. [ABSTRACT FROM AUTHOR]

The possibility of using a smartwatch as a rehabilitation tool to monitor patients' heart rates during exercise has gained the attention of many researchers. This study aimed to evaluate the accuracy and precision of the HR measurement performed by two wrist monitors: the Fitbit Charge 4 and the Xiaomi Mi Band 5. Thirty-one healthy volunteers were asked to perform a stress test on a treadmill. Their heart rates were recorded simultaneously by the wristbands and an electrocardiogram (ECG) at 1 min intervals. The mean absolute error percentage (MAPE), Lin's concordance correlation coefficient (LCCC), and Bland–Altman analysis were calculated to compare the precision and accuracy of heart rate measurements. The estimated validation criteria were MAPE < 10% and LCCC < 0.8. The overall MAPE and LCCC of the Fitbit were 10.19% (±11.79%) and 0.753 (95% CI: 0.717–0.785), respectively. The MAPE and LCCC of the Xiaomi were 6.89% (±9.75) and 0.903 (0.886–0.917), respectively. The precision and accuracy of both devices decreased with the increased exercise intensity. The accuracy of wearable wrist-worn heart rate monitors varies and depends on the intensity of training. Therefore, the decision to use such a device as a heart rate monitor during in-home rehabilitation should be made with caution. [ABSTRACT FROM AUTHOR]

The development of smart cars with e-health services allows monitoring of the health condition of the driver. Driver comfort is preserved by the use of capacitive electrodes, but the recorded signal is characterized by large artifacts. This paper proposes a method for reducing artifacts from the ECG signal recorded by capacitive electrodes (cECG) in moving subjects. Two dominant artifact types are coarse and slow-changing artifacts. Slow-changing artifacts removal by classical filtering is not feasible as the spectral bands of artifacts and cECG overlap, mostly in the band from 0.5 to 15 Hz. We developed a method for artifact removal, based on estimating the fluctuation around linear trend, for both artifact types, including a condition for determining the presence of coarse artifacts. The method was validated on cECG recorded while driving, with the artifacts predominantly due to the movements, as well as on cECG recorded while lying, where the movements were performed according to a predefined protocol. The proposed method eliminates 96% to 100% of the coarse artifacts, while the slow-changing artifacts are completely reduced for the recorded cECG signals larger than 0.3 V. The obtained results are in accordance with the opinion of medical experts. The method is intended for reliable extraction of cardiovascular parameters to monitor driver fatigue status. [ABSTRACT FROM AUTHOR]

Heart rate (HR) and heart rate variability (HRV) based physiological metrics such as Excess Post-exercise Oxygen Consumption (EPOC), Energy Expenditure (EE), and Training Impulse (TRIMP) are widely utilized in coaching to monitor and optimize an athlete's training load. Chest straps, and recently also dry electrodes integrated to special sports vests, are used to monitor HR during sports. Mechanical design, placement of electrodes, and ergonomics of the sensor affect the measured signal quality and artefacts. To evaluate the impact of the sensor mechanical design on the accuracy of the HR/HRV and further on to estimation of EPOC, EE, and TRIMP, we recorded HR and HRV from a chest strap and a vest with the same ECG sensor during supervised exercise protocol. A 3-lead clinical Holter ECG was used as a reference. Twenty-five healthy subjects (six females) participated. Mean absolute percentage error (MAPE) for HR was 0.76% with chest strap and 3.32% with vest. MAPE was 1.70% vs. 6.73% for EE, 0.38% vs. 8.99% for TRIMP and 3.90% vs. 54.15% for EPOC with chest strap and vest, respectively. Results suggest superior accuracy of chest strap over vest for HR and physiological metrics monitoring during sports. [ABSTRACT FROM AUTHOR]

Camera-based remote photoplethysmography (rPPG) is a low-cost and casual non-contact heart rate measurement method suitable for telemedicine. Several factors affect the accuracy of measuring the heart rate and heart rate variability (HRV) using rPPG despite HRV being an important indicator for healthcare monitoring. This study aimed to investigate the appropriate setup for precise HRV measurements using rPPG while considering the effects of possible factors including illumination, direction of the light, frame rate of the camera, and body motion. In the lighting conditions experiment, the smallest mean absolute R–R interval (RRI) error was obtained when light greater than 500 lux was cast from the front (among the following conditions—illuminance: 100, 300, 500, and 700 lux; directions: front, top, and front and top). In addition, the RRI and HRV were measured with sufficient accuracy at frame rates above 30 fps. The accuracy of the HRV measurement was greatly reduced when the body motion was not constrained; thus, it is necessary to limit the body motion, especially the head motion, in an actual telemedicine situation. The results of this study can act as guidelines for setting up the shooting environment and camera settings for rPPG use in telemedicine. [ABSTRACT FROM AUTHOR]

Today's wearable medical devices are becoming popular because of their price and ease of use. Most wearable medical devices allow users to continuously collect and check their health data, such as electrocardiograms (ECG). Therefore, many of these devices have been used to monitor patients with potential heart pathology as they perform their daily activities. However, one major challenge of collecting heart data using mobile ECG is baseline wander and motion artifacts created by the patient's daily activities, resulting in false diagnoses. This paper proposes a new algorithm that automatically removes the baseline wander and suppresses most motion artifacts in mobile ECG recordings. This algorithm clearly shows a significant improvement compared to the conventional noise removal method. Two signal quality metrics are used to compare a reference ECG with its noisy version: correlation coefficients and mean squared error. For both metrics, the experimental results demonstrate that the noisy signal filtered by our algorithm is improved by a factor of ten. [ABSTRACT FROM AUTHOR]

New and emerging non-invasive digital tools, such as eye-tracking, facial expression and physiological biometrics, have been implemented to extract more objective sensory responses by panelists from packaging and, specifically, labels. However, integrating these technologies from different company providers and software for data acquisition and analysis makes their practical application difficult for research and the industry. This study proposed a prototype integration between eye tracking and emotional biometrics using the BioSensory computer application for three sample labels: Stevia, Potato chips, and Spaghetti. Multivariate data analyses are presented, showing the integrative analysis approach of the proposed prototype system. Further studies can be conducted with this system and integrating other biometrics available, such as physiological response with heart rate, blood, pressure, and temperature changes analyzed while focusing on different label components or packaging features. By maximizing data extraction from various components of packaging and labels, smart predictive systems can also be implemented, such as machine learning to assess liking and other parameters of interest from the whole package and specific components. [ABSTRACT FROM AUTHOR]

eSports is a rapidly growing industry with increasing investment and large-scale international tournaments offering significant prizes. This has led to an increased focus on individual and team performance with factors such as communication, concentration, and team intelligence identified as important to success. Over a similar period of time, personal physiological monitoring technologies have become commonplace with clinical grade assessment available across a range of parameters that have evidenced utility. The use of physiological data to assess concentration is an area of growing interest in eSports. However, body-worn devices, typically used for physiological data collection, may constitute a distraction and/or discomfort for the subjects. To this end, in this work we devise a novel "invisible" sensing approach, exploring new materials, and proposing a proof-of-concept data collection system in the form of a keyboard armrest and mouse. These enable measurements as an extension of the interaction with the computer. In order to evaluate the proposed approach, measurements were performed using our system and a gold standard device, involving 7 healthy subjects. A particularly advantageous characteristic of our setup is the use of conductive nappa leather, as it preserves the standard look and feel of the keyboard and mouse. According to the results obtained, this approach shows 3–15% signal loss, with a mean difference in heart rate between the reference and experimental device of −1.778 ± 4.654 beats per minute (BPM); in terms of ECG waveform morphology, the best cases show a Pearson correlation coefficient above 0.99. [ABSTRACT FROM AUTHOR]

Heart rate (HR) is an essential indicator of health in the human body. It measures the number of times per minute that the heart contracts or beats. An irregular heartbeat can signify a severe health condition, so monitoring heart rate periodically can help prevent heart complications. This paper presents a novel wearable sensing approach for remote HR measurement by a compact resistance-to-microcontroller interface circuit. A heartbeat's signal can be detected by a Force Sensing Resistor (FSR) attached to the body near large arteries (such as the carotid or radial), which expand their area each time the heart expels blood to the body. Depending on how the sensor interfaces with the subject, the FSR changes its electrical resistance every time a pulse is detected. By placing the FSR in a direct interface circuit, those resistance variations can be measured directly by a microcontroller without using either analog processing stages or an analog-to-digital converter. In this kind of interface, the self-heating of the sensor is avoided, since the FSR does not require any voltage or bias current. The proposed system has a sampling rate of 50 Sa/s, and an effective resolution of 10 bits (200 mΩ), enough for obtaining well-shaped cardiac signals and heart rate estimations in real time by the microcontroller. With this approach, the implementation of wearable systems in health monitoring applications is more feasible. [ABSTRACT FROM AUTHOR]

Ephedrine, the main active ingredient of mahuang, may lead to weight loss; however, it can also induce cardiovascular side effects. As ephedrine use remains controversial, this study aimed to systematically review previous studies on ephedrine-containing products and perform meta-analysis of the existing evidence on weight, blood pressure (BP), heart rate, and lipid change effects of ephedrine-containing products. We searched for placebo-controlled randomized studies in PubMed, Web of Science, and EMBASE until July 2021 using the following search terms: (ephedr* OR mahuang) AND ("weight loss" OR obes* OR overweight). Mean differences (MDs) and 95% confidence intervals (CIs) were calculated to evaluate the effects of ephedrine-containing products on weight, BP, heart rate, and lipid profiles. A total of 10 articles were included. Compared with the placebo group, the ephedrine-containing product group was associated with greater weight loss, with an MD of −1.97 kg (95% CI: −2.38, −1.57). In the ephedrine-containing product group, the mean heart rate was 5.76 beats/min higher than in the placebo group (95% CI: 3.42, 8.10), whereas intergroup differences in systolic and diastolic BP were not statistically significant. The ephedrine-containing product group had a significantly higher mean high-density lipoprotein cholesterol level (MD: 2.74 mg/dL; 95% CI: 0.94, 4.55), lower mean low-density lipoprotein cholesterol level (MD: −5.98 mg/dL; 95% CI: −10.97, −0.99), and lower mean triglyceride level (MD: −11.25 mg/dL; 95% CI: −21.83, −0.68) than the placebo group. Compared with placebo, the ephedrine-containing products showed better effects on weight loss and lipid profiles, whereas they caused increased heart rate. The ephedrine-containing products may be beneficial to obese or overweight patients; however, close monitoring is needed, especially heart rate monitoring. [ABSTRACT FROM AUTHOR]

Vital signal detection using multiple radars is proposed to reduce the signal degradation from a subject's body movement. The phase variation in the transceiving signals of continuous-wave radar due to respiration and heartbeat is generated by the body surface movement of the organs monitored in the line-of-sight (LOS) of the radar. The body movement signals obtained by two adjacent radars can be assumed to be the same over a certain distance. However, the vital signals are different in each radar, and each radar has a different LOS because of the asymmetric movement of lungs and heart. The proposed method uses two adjacent radars with different LOS to obtain correlated signals that reinforce the difference in the asymmetrical movement of the organs. The correlated signals can improve the signal-to-noise ratio in vital signal detection because of a reduction in the body movement effect. Two radars at different frequencies in the 5.8 GHz band are implemented to reduce direct signal coupling. Measurement results using the radars arranged at angles of 30°, 45°, and 60° showed that the proposed method can detect the vital signals with a mean accuracy of 97.8% for the subject moving at a maximum velocity of 53.4 mm/s. [ABSTRACT FROM AUTHOR]

Heart rate is one of the most important diagnostic bases for cardiovascular disease. This paper introduces a deep autoencoding strategy into feature extraction of electrocardiogram (ECG) signals, and proposes a beat-to-beat heart rate estimation method based on convolution autoencoding and Gaussian mixture clustering. The high-level heartbeat features were first extracted in an unsupervised manner by training the convolutional autoencoder network, and then the adaptive Gaussian mixture clustering was applied to detect the heartbeat locations from the extracted features, and calculated the beat-to-beat heart rate. Compared with the existing heartbeat classification/detection methods, the proposed unsupervised feature learning and heartbeat clustering method does not rely on accurate labeling of each heartbeat location, which could save a lot of time and effort in human annotations. Experimental results demonstrate that the proposed method maintains better accuracy and generalization ability compared with the existing ECG heart rate estimation methods and could be a robust long-time heart rate monitoring solution for wearable ECG devices. [ABSTRACT FROM AUTHOR]

The development and use of wearable devices require high levels of security and have sparked interest in biometric authentication research. Among the available approaches, electrocardiogram (ECG) technology is attracting attention because of its strengths in spoofing. However, morphological changes of ECG, which are affected by physical and psychological factors, can make authentication difficult. In this paper, we propose authentication using non-linear normalization of ECG beats that is robust to changes in ECG waveforms according to heart rate fluctuations in various daily activities. We performed a non-linear normalization method through the analysis of ECG alongside heart rate, evaluating similarities and authenticating the performance of our new method compared to existing methods. Compared with beats before normalization, the average similarity of the proposed method increased 23.7% in the resting state and 43% in the non-resting state. After learning in the resting state, authentication performance reached 99.05% accuracy for the resting state and 88.14% for the non-resting state. The proposed method can be applicable to an ECG-based authentication system under various physiological conditions. [ABSTRACT FROM AUTHOR]

The current diagnostic procedures for assessing physiological response to exercise comprise blood lactates measurements, ergospirometry, and electrocardiography. The first is not continuous, the second requires specialized equipment distorting natural breathing, and the last is indirect. Therefore, we decided to perform the feasibility study with impedance pneumography as an alternative technique. We attempted to determine points in respiratory-related signals, acquired during stress test conditions, that suggest a transition similar to the gas exchange threshold. In addition, we analyzed whether or not respiratory activity reaches steady states during graded exercise. Forty-four students (35 females), practicing sports on different levels, performed a graded exercise test until exhaustion on cycloergometer. Eventually, the results from 34 of them were used. The data were acquired with Pneumonitor 2. The signals demonstrated that the steady state phenomenon is not as evident as for heart rate. The results indicated respiratory rate approaches show the transition point at the earliest (more than 6 min before the end of the exercise test on average), and the tidal volume ones at the latest (less than 5 min). A combination gave intermediate findings. The results showed the impedance pneumography appears reasonable for the transition point estimation, but this should be further studied with the reference. [ABSTRACT FROM AUTHOR]

The availability of standardized guidelines regarding the use of electronic fetal monitoring (EFM) in clinical practice has not effectively helped to solve the main drawbacks of fetal heart rate (FHR) surveillance methodology, which still presents inter- and intra-observer variability as well as uncertainty in the classification of unreassuring or risky FHR recordings. Given the clinical relevance of the interpretation of FHR traces as well as the role of FHR as a marker of fetal wellbeing autonomous nervous system development, many different approaches for computerized processing and analysis of FHR patterns have been proposed in the literature. The objective of this review is to describe the techniques, methodologies, and algorithms proposed in this field so far, reporting their main achievements and discussing the value they brought to the scientific and clinical community. The review explores the following two main approaches to the processing and analysis of FHR signals: traditional (or linear) methodologies, namely, time and frequency domain analysis, and less conventional (or nonlinear) techniques. In this scenario, the emerging role and the opportunities offered by Artificial Intelligence tools, representing the future direction of EFM, are also discussed with a specific focus on the use of Artificial Neural Networks, whose application to the analysis of accelerations in FHR signals is also examined in a case study conducted by the authors. [ABSTRACT FROM AUTHOR]

Electrocardiogram (ECG) synchronization is useful to avoid the effects of cardiac motion in medical measurements, and is widely used in standard medical imaging. A number of medical equipment include embedded commercial synchronizers. However, the use of independent synchronization modules is sometimes needed when several non-integrated instruments are used, or in the development of new medical instruments and procedures. We present a simple low-cost ECG synchronizer module based on an Arduino controller board that converts the ECG signal into a transistor-transistor-logic (TTL) one, allowing real-time medical measurements triggered at specific phases of the cardiac cycle. The device and conversion algorithm developed is optimized in vitro using synthetic and human ECG signals, and tested in vivo on three swine specimens. Error rates during the in vivo testing stage remain below the 2% of the cycles in all animals and critical false positives are less than 1%, which is sufficient for most applications. Possible algorithm updates are discussed if its performance needs to be improved. [ABSTRACT FROM AUTHOR]

The COVID-19 pandemic has wreaked havoc globally and still persists even after a year of its initial outbreak. Several reasons can be considered: people are in close contact with each other, i.e., at a short range (1 m), and the healthcare system is not sufficiently developed or does not have enough facilities to manage and fight the pandemic, even in developed countries such as the USA and the U.K. and countries in Europe. There is a great need in healthcare for remote monitoring of COVID-19 symptoms. In the past year, a number of IoT-based devices and wearables have been introduced by researchers, providing good results in terms of high accuracy in diagnosing patients in the prodromal phase and in monitoring the symptoms of patients, i.e., respiratory rate, heart rate, temperature, etc. In this systematic review, we analyzed these wearables and their need in the healthcare system. The research was conducted using three databases: IEEE Xplore®, Web of Science®, and PubMed Central®, between December 2019 and June 2021. This article was based on the PRISMA guidelines. Initially, 1100 articles were identified while searching the scientific literature regarding this topic. After screening, ultimately, 70 articles were fully evaluated and included in this review. These articles were divided into two categories. The first one belongs to the on-body sensors (wearables), their types and positions, and the use of AI technology with ehealth wearables in different scenarios from screening to contact tracing. In the second category, we discuss the problems and solutions with respect to utilizing these wearables globally. This systematic review provides an extensive overview of wearable systems for the remote management and automated assessment of COVID-19, taking into account the reliability and acceptability of the implemented technologies. [ABSTRACT FROM AUTHOR]

This paper focuses on developing an adaptive heart rate monitoring algorithm for wrist-based rehabilitation systems. Due to the characteristics of the wrist, the heartbeat measurements are unstable. To improve the preprocessing efficiency and perform measurement calibration, a novel joint algorithm incorporating automatic multiscale-based peak detection and fuzzy logic control (AMPD-Fuzzy) is proposed. The monitoring approach consists of two phases: (1) Preprocessing and (2) Detection and Calibration. Phase 1 explores the parameter settings, threshold, and decision rules. Phase 2 applies fuzzy logic control and the Laplacian model to provide signal reshaping. Experimental results show that the proposed algorithm can effectively achieve heart rate monitoring for wearable healthcare devices. [ABSTRACT FROM AUTHOR]

Recent advances in wearable technologies integrating multi-modal sensors have enabled the in-field monitoring of several physiological metrics. In sport applications, wearable devices have been widely used to improve performance while minimizing the risk of injuries and illness. The objective of this project is to estimate breathing rate (BR) from respiratory sinus arrhythmia (RSA) using heart rate (HR) recorded with a chest belt during physical activities, yielding additional physiological insight without the need of an additional sensor. Thirty-one healthy adults performed a run at increasing speed until exhaustion on an instrumented treadmill. RR intervals were measured using the Polar H10 HR monitoring system attached to a chest belt. A metabolic measurement system was used as a reference to evaluate the accuracy of the BR estimation. The evaluation of the algorithms consisted of exploring two pre-processing methods (band-pass filters and relative RR intervals transformation) with different instantaneous frequency tracking algorithms (short-term Fourier transform, single frequency tracking, harmonic frequency tracking and peak detection). The two most accurate BR estimations were achieved by combining band-pass filters with short-term Fourier transform, and relative RR intervals transformation with harmonic frequency tracking, showing 5.5% and 7.6% errors, respectively. These two methods were found to provide reasonably accurate BR estimation over a wide range of breathing frequency. Future challenges consist in applying/validating our approaches during in-field endurance running in the context of fatigue assessment. [ABSTRACT FROM AUTHOR]

The study examined whether the performance characteristics of male university field hockey players differed when the match format was 2 × 35 min halves compared to 2 × 2 × 17.5 min quarters. Thirty-five male university field hockey players (age 21.2 ± 3.0 years, height 1.81 ± 0.07 m, body mass 75.1 ± 8.9 kg), competing at national level in the UK, were monitored over 52 matches played across the 2018–2019 (2 × 35 min halves) and 2019–2020 (2 × 2 × 17.5 min quarters) seasons using 15 Hz Global Positioning System units and heart rate monitors. Total distance, high-speed running distance (≥15.5 km·h−1), accelerations (≥2 m·s−1), decelerations (≤−2 m·s−1), average heart rate and percentage of time spent at >85% of maximum heart rate were recorded during both match formats. Two-level random intercept hierarchal models (Match—level 1, Player—level 2) suggested that the change in format from 2 × 35 min halves (2018–2019 season) to 2 × 2 × 17.5 min quarters (2019–2020 season) resulted in a reduction in total distance and high-speed running distance completed during a match (by 221 m and 120 m, respectively, both p < 0.001). As no significant cross-level interactions were observed (between season and half), the change from 35 min halves to 17.5 min quarters did not attenuate the reduced physical performance evident during the second half of matches (total distance: −235 m less in second half; high-speed running distance: −70 m less in second half; both p < 0.001). Overall, the findings suggest that the change in match format did alter the performance characteristics of male university field hockey players, but the quarter format actually reduced the total distance and high-speed running distance completed during matches, and did not attenuate the reduction in performance seen during the second half of matches. [ABSTRACT FROM AUTHOR]

The aim of this review is to investigate the common wearable devices currently used in field hockey competitions, and to understand the hockey-specific parameters these devices measure. A systematic search was conducted by using three electronic databases and search terms that included field hockey, wearables, accelerometers, inertial sensors, global positioning system (GPS), heart rate monitors, load, performance analysis, player activity profiles, and competitions from the earliest record. The review included 39 studies that used wearable devices during competitions. GPS units were found to be the most common wearable in elite field hockey competitions, followed by heart rate monitors. Wearables in field hockey are mostly used to measure player activity profiles and physiological demands. Inconsistencies in sampling rates and performance bands make comparisons between studies challenging. Nonetheless, this review demonstrated that wearable devices are being used for various applications in field hockey. Researchers, engineers, coaches, and sport scientists can consider using GPS units of higher sampling rates, as well as including additional variables such as skin temperatures and injury associations, to provide a more thorough evaluation of players' physical and physiological performances. Future work should include goalkeepers and non-elite players who are less studied in the current literature. [ABSTRACT FROM AUTHOR]

Non-invasive photoplethysmography (PPG) technology was developed to track heart rate during physical activity under free-living conditions. Automated analysis of PPG has made it useful in both clinical and non-clinical applications. Because of their generalization capabilities, deep learning methods can be a major direction in the search for a heart rate estimation solution based on signals from wearable devices. A novel multi-headed convolutional neural network model enriched with long short-term memory cells (MH Conv-LSTM DeepPPG) was proposed for the estimation of heart rate based on signals measured by a wrist-worn wearable device, such as PPG and acceleration signals. For the PPG-DaLiA dataset, the proposed solution improves the performance of previously proposed methods. An experimental approach was used to develop the final network architecture. The average mean absolute error (MAE) of the final solution was 6.28 bpm and Pearson's correlation coefficient between the estimated and true heart rate values was 0.85. [ABSTRACT FROM AUTHOR]

The accuracy of target distance obtained by a frequency modulated continuous wave (FMCW) laser ranging system is often affected by factors such as white Gaussian noise (WGN), spectrum leakage, and the picket fence effect. There are some traditional spectrum correction algorithms to solve the problem above, but the results are unsatisfactory. In this article, a decomposition filtering-based dual-window correction (DFBDWC) algorithm is proposed to alleviate the problem caused by these factors. This algorithm reduces the influence of these factors by utilizing a decomposition filtering, dual-window in time domain and two phase values of spectral peak in the frequency domain, respectively. With the comparison of DFBDWC and these traditional algorithms in simulation and experiment on a built platform, the results show a superior performance of DFBDWC based on this platform. The maximum absolute error of target distance calculated by this algorithm is reduced from 0.7937 m of discrete Fourier transform (DFT) algorithm to 0.0407 m, which is the best among all mentioned spectrum correction algorithms. A high performance FMCW laser ranging system can be realized with the proposed algorithm, which has attractive potential in a wide scope of applications. [ABSTRACT FROM AUTHOR]

Physical exercise (PE) has become an essential tool for different rehabilitation programs. High-intensity exercises (HIEs) have been demonstrated to provide better results in general health conditions, compared with low and moderate-intensity exercises. In this context, monitoring of a patients' condition is essential to avoid extreme fatigue conditions, which may cause physical and physiological complications. Different methods have been proposed for fatigue estimation, such as: monitoring the subject's physiological parameters and subjective scales. However, there is still a need for practical procedures that provide an objective estimation, especially for HIEs. In this work, considering that the sit-to-stand (STS) exercise is one of the most implemented in physical rehabilitation, a computational model for estimating fatigue during this exercise is proposed. A study with 60 healthy volunteers was carried out to obtain a data set to develop and evaluate the proposed model. According to the literature, this model estimates three fatigue conditions (low, moderate, and high) by monitoring 32 STS kinematic features and the heart rate from a set of ambulatory sensors (Kinect and Zephyr sensors). Results show that a random forest model composed of 60 sub-classifiers presented an accuracy of 82.5% in the classification task. Moreover, results suggest that the movement of the upper body part is the most relevant feature for fatigue estimation. Movements of the lower body and the heart rate also contribute to essential information for identifying the fatigue condition. This work presents a promising tool for physical rehabilitation. [ABSTRACT FROM AUTHOR]

Electrocardiogram (ECG) signals have been used to monitor and diagnose signs of cardiovascular disease and abnormal signals about the human body. ECG signals are typically characterized by the PR, QRS, QT interval, ST-segment, and heart rate (HR) parameters. ECG devices are widely used for many applications, especially for the elderly. However, ECG signals are often affected by noises from the environment. There are mainly two types of noises that affect the ECG signals: low frequencies from muscle activity and 50/60 Hz from the electrical grid. Removing these noises is important for improving the quality of the ECG signal. A clear ECG signal makes it easy to diagnose cardiovascular problems. ECG signals with high sampling frequency are more accurate. However, the noises in the signal will be more obvious and it will be difficult to remove these noises with filters. We analyzed the symmetrical correlation between the sampling frequency of the signal and the parameters of the signal such as signal to noise ratio (SNR) and signal amplitude. This study will compare characterization of ECG signals performed at different sampling frequencies before and after applying infinite impulse response (IIR) and symmetric finite impulse response (FIR) filters. Therefore, it is critical that the sampling frequency is consistent at the same frequency of the ECG signal for accurate diagnosis. Furthermore, the approach can be also important for the device to help reduce the device's computing power and hardware resources. Our results were tested with the MIT/ BIH database at 360 Hz sampling frequency with 11-bit resolution. We also experimented with the device operating in real-time with a sampling frequency from 100 Hz to 2133 Hz and a 24-bit resolution. The test results show the advantages of the symmetric FIR filter over IIR when applied to the filtering of ECG signals. The study's conclusions can be applied to real-world devices to improve the quality of ECG signals. [ABSTRACT FROM AUTHOR]

Radar-based non-contact vital signs monitoring has great value in through-wall detection applications. This paper presents the theoretical and experimental study of through-wall respiration and heartbeat pattern extraction from multiple subjects. To detect the vital signs of multiple subjects, we employ a low-frequency ultra-wideband (UWB) multiple-input multiple-output (MIMO) imaging radar and derive the relationship between radar images and vibrations caused by human cardiopulmonary movements. The derivation indicates that MIMO radar imaging with the stepped-frequency continuous-wave (SFCW) improves the signal-to-noise ratio (SNR) critically by the factor of radar channel number times frequency number compared with continuous-wave (CW) Doppler radars. We also apply the three-dimensional (3-D) higher-order cumulant (HOC) to locate multiple subjects and extract the phase sequence of the radar images as the vital signs signal. To monitor the cardiopulmonary activities, we further exploit the VMD algorithm with a proposed grouping criterion to adaptively separate the respiration and heartbeat patterns. A series of experiments have validated the localization and detection of multiple subjects behind a wall. The VMD algorithm is suitable for separating the weaker heartbeat pattern from the stronger respiration pattern by the grouping criterion. Moreover, the continuous monitoring of heart rate (HR) by the MIMO radar in real scenarios shows a strong consistency with the reference electrocardiogram (ECG). [ABSTRACT FROM AUTHOR]

Accelerations (ACC) and decelerations (DEC) are important and frequent actions in soccer. We aimed to investigate whether ACC and DEC were good indicators of the variation of training loads in elite women soccer players. Changes in the training load were monitored during two different selected weeks (considered a "low week" and a "heavy week") during the in-season. Twelve elite soccer women playing in the French first division wore a 10-Hz Global Positioning System unit recording total distance, distance within speed ranges, sprint number, ACC, DEC, and a heart rate monitor during six soccer training sessions and rated their perceived exertion (RPE). They answered the Hooper questionnaire (sleep, stress, fatigue, DOMS) to get an insight of their subjective fitness level at the start (Hooper S) and at the end of each week (Hooper E). A countermovement jump (CMJ) was also performed once a week. During the heavy week, the training load was significantly greater than the low week when considering number of ACC >2 m·s−2 (28.2 ± 11.9 vs. 56.1 ± 10.1, p < 0.001) and number of DEC < −2 m·s−2 (31.5 ± 13.4 vs. 60.9 ± 14.4, p < 0.001). The mean heart rate percentage (HR%) (p < 0.05), RPE (p < 0.001), and Hooper E (p < 0.001) were significantly greater during the heavy week. ACC and DEC showed significant correlations with most outcomes: HR%, total distance, distance per min, sprint number, Hooper index of Hooper E, DOMS E, Fatigue E, RPE, and session RPE. We concluded that, for elite women soccer players, quantifying ACC and DEC alongside other indicators seemed to be essential for a more complete training load monitoring. Indeed, it could lead to a better understanding of the reasons why athletes get fatigued and give insight into neuromuscular, rather than only energetic, fatigue. [ABSTRACT FROM AUTHOR]

Smartwatches are being increasingly used in research to monitor heart rate (HR). However, it is debatable whether the data from smartwatches are of high enough quality to be applied in assessing the health impacts of air pollutants. The objective of this study was to assess whether smartwatches are useful complements to certified medical devices for assessing PM2.5 health impacts. Smartwatches and medical devices were used to measure HR for 7 and 2 days consecutively, respectively, for 49 subjects in 2020 in Taiwan. Their associations with PM2.5 from low-cost sensing devices were assessed. Good correlations in HR were found between smartwatches and certified medical devices (rs > 0.6, except for exercise, commuting, and worshipping). The health damage coefficients obtained from smartwatches (0.282% increase per 10 μg/m3 increase in PM2.5) showed the same direction, with a difference of only 8.74% in magnitude compared to those obtained from certified medical devices. Additionally, with large sample sizes, the health impacts during high-intensity activities were assessed. Our work demonstrates that smartwatches are useful complements to certified medical devices in PM2.5 health assessment, which can be replicated in developing countries. [ABSTRACT FROM AUTHOR]

Multi-channel measurements from the maternal abdomen acquired by means of dry electrodes can be employed to promote long-term monitoring of fetal heart rate (fHR). The signals acquired with this type of electrode have a lower signal-to-noise ratio and different artifacts compared to signals acquired with conventional wet electrodes. Therefore, starting from the benchmark algorithm with the best performance for fHR estimation proposed by Varanini et al., we propose a new method specifically designed to remove artifacts typical of dry-electrode recordings. To test the algorithm, experimental textile electrodes were employed that produce artifacts typical of dry and capacitive electrodes. The proposed solution is based on a hybrid (hardware and software) pre-processing step designed specifically to remove the disturbing component typical of signals acquired with these electrodes (triboelectricity artifacts and amplitude modulations). The following main processing steps consist of the removal of the maternal ECG by blind source separation, the enhancement of the fetal ECG and identification of the fetal QRS complexes. Main processing is designed to be robust to the high-amplitude motion artifacts that corrupt the acquisition. The obtained denoising system was compared with the benchmark algorithm both on semi-simulated and on real data. The performance, quantified by means of sensitivity, F1-score and root-mean-square error metrics, outperforms the performance obtained with the original method available in the literature. This result proves that the design of a dedicated processing system based on the signal characteristics is necessary for reliable and accurate estimation of the fHR using dry, textile electrodes. [ABSTRACT FROM AUTHOR]

Scientific research on heart rate variability (HRV) biofeedback is burdened by certain methodological issues, such as lack of consistent training quality and fidelity assessment or control conditions that would mimic the intervention. In the present study, a novel sham HRV-biofeedback training was proposed as a credible control condition, indistinguishable from the real training. The Yield Efficiency of Training Index (YETI), a quantitative measure based on the spectral distribution of heart rate during training, was suggested for training quality assessment. A training fidelity criterion derived from a two-step classification process based on the average YETI index and its standard deviation (YETISD) was suggested. We divided 57 young, healthy volunteers into two groups, each subjected to 20 sessions of either real or sham HRV-biofeedback. Five standard HRV measures (standard deviation of the NN (SDNN), root mean square of the standard deviation of the NN (RMSSD), total power, low-frequency (LF), and high-frequency (HF) power) collected at baseline, after 10 and 20 sessions were subjected to analysis of variance. Application of a training fidelity criterion improved sample homogeneity, resulting in a substantial gain in effect sizes of the group and training interactions for all considered HRV indices. Application of methodological amendments, including proper control conditions (such as sham training) and quantitative assessment of training quality and fidelity, substantially improves the analysis of training effects. Although presented on the example of HRV-biofeedback, this approach should similarly benefit other behavioral training procedures that interact with any of the many psychophysiological mechanisms in the human body. [ABSTRACT FROM AUTHOR]

Despite the popularity of commercially available wearable activity monitors (WAMs), there is a paucity of consistent methodology for analyzing large amounts of accelerometer data from these devices. This multimethod study aimed to inform appropriate Fitbit wear thresholds for physical activity (PA) outcomes assessment in a sample of 616 low-income, majority Latina patients with obesity enrolled in a behavioral weight-loss intervention. Secondly, this study aimed to understand intervention participants' barriers to Fitbit use. We applied a heart rate (HR) criterion (≥10 h/day) and a step count (SC) criterion (≥1000 steps/day) to 100 days of continuous activity monitor data. We examined the prevalence of valid wear and PA outcomes between analytic subgroups of participants who met the HR criterion, SC criterion, or both. We undertook qualitative analysis of research staff notes and participant interviews to explore barriers to valid Fitbit data collection. Overall, one in three participants did not meet the SC criterion for valid wear in Weeks 1 and 13; however, we found the SC criterion to be more inclusive of participants who did not use a smartphone than the HR criterion. Older age, higher body mass index (BMI), barriers to smartphone use, device storage issues, and negative emotional responses to WAM-based self-monitoring may predict higher proportions of invalid WAM data in weight-loss intervention research. [ABSTRACT FROM AUTHOR]

Heart rate variability (HRV) represents the activity and balance of the autonomic nervous system and its capability to react to internal and external stimuli. As a measure of general body homeostasis, HRV is linked to lifestyle factors and it is associated with morbidity and mortality. It is easily accessible by heart rate monitoring and gains interest in the era of smart watches and self-monitoring. In this review, we summarize effects of weight loss, training, and nutrition on HRV with a special focus on obesity. Besides weight reduction, effects of physical activity and dietary intervention can be monitored by parameters of HRV, including its time and frequency domain components. In the future, monitoring of HRV should be included in any weight reduction program as it provides an additional tool to analyze the effect of body weight on general health and homeostasis. HRV parameters could, for example, be monitored easily by implementation of an electrocardiogram (ECG) every two to four weeks during weight reduction period. Indices presumibly showing beneficial changes could be a reduction in heart rate and the number of premature ventricular complexes as well as an increase in standard deviation of normal-to-normal beat intervals (SDNN), just to name some. [ABSTRACT FROM AUTHOR]

Objective: In this pilot clinical study we investigated the effect on blood pressure (BP) of two community-based exercise training programs of high (HIT) vs. low-moderate intensity (LMIT) in hypertensive individuals receiving at least one antihypertensive drug. Methods: The study included two phases of physical exercises based on 1-h session, 3 days/week for 12 and 16 weeks, respectively, separately by a 7-week resting period. Each phase was preceded by a four-week conditioning training period. According to the average maximal heart rate at baseline, participants were randomized to HIT (80–90%), LMIT (50–70%) or no-exercise (control). Heart rate was monitored during workout and BP profiles were registered by ambulatory BP monitoring at the beginning and end of each phase. Results: Of 60 individuals randomized, 44 completed the study (HIT, n = 10; LMIT, n = 16; controls, n = 18). BP levels were significantly reduced after the second phase for both LMIT (SBP −3.1 mmHg, DBP −2.4 mmHg) and HIT (SBP −10.8 mmHg, DBP −8.3 mmHg). Similar levels of improvement were also found in daytime and night-time BP. Mean attendance of the prescribed training sessions was 87.4 ± 6.2% for HIT and 87.4 ± 5.3% for LMIT during the first phase and 84.1 ± 5.0% and 85.2 ± 5.9% during the second phase, respectively (p = 0.047). Conclusion: Both HIT and LMIT exercise training programs reduced BP but the HIT modality showed a lower rate of compliance with proposed training schedule. Intensity of training should be individually prescribed to improve tolerance to more high intensity exercises. [ABSTRACT FROM AUTHOR]