Search

Construction of earth fill dams offers a cost-effective solution for various purposes. However, their susceptibility to internal soil erosion, known as piping, poses a significant risk of structural failure and resultant loss of life and property. Soil stabilization emerges as a practical technique to fortify these dams against such threats. This study investigated the impact of lime on the internal erosion properties of clay soils, focusing on CH and ML soil types. Specimens of different lime content were prepared and remolded at 95% relative compaction and optimum moisture content. Hole Erosion tests at varying lime concentrations and curing durations were adapted to conduct the investigation. This investigation aims to optimize lime content and curing time for cohesive soil stabilization against internal erosion. Findings revealed that 2% and 5% of quicklime, by dry weight of the soil, effectively stabilized CH and ML soils, respectively, against internal erosion, with a two-day curing period proving optimal. Furthermore, the addition of lime significantly enhanced erosion rate index and critical shear strength in clay soil, underscoring its efficacy in soil stabilization efforts. [ABSTRACT FROM AUTHOR]

The main thrust of this research was to establish any benefits of mellowing, and the optimal moisture content (OMC) for compacting mellowed sulphate-bearing clay soil undergoing the stabilization process. Two three-day mellowing regimes were carried out, prior to final compaction, at different initial moisture contents of 30% or 40% OMC. The unmellowed specimens were compacted immediately after mixing with the blended stabilizers. A blend of quicklime (L) with a sustainable by-product, silica fume (SF), at a 1:1 ratio (2%L–2%SF) was used. Linear expansion and unconfined compressive strength (UCS) tests were carried out to evaluate the benefits of mellowing. The test results suggested that the mellowed test specimens achieved better UCS and swelling properties compared to the unmellowed specimens. Mellowing at 1.2 OMC produced better strength performance than at 1.4 OMC, whereas mellowed specimens at 1.4 OMC showed better resistance to linear expansion compared to 1.2 OMC. The research findings suggested that optimal performance was achieved by mellowing at the higher initial moisture condition of 40% OMC and compacting the materials at the lower moisture condition of 1.2 OMC. [ABSTRACT FROM AUTHOR]

Cropland soils are key systems in global carbon budgets due to their high carbon-sequestration potential. It is widely accepted that clays are one of the soil components that have a significant effect on the stabilisation of soil organic carbon (SOC), owing to its surface interactions with organic molecules. However, the identification of the direct effects of clays on SOC stabilization is complicated, mainly due to the difficulty of accurately characterizing the mineralogy of clays, especially phyllosilicates. In this study, the relationships between soil phyllosilicates and functional SOC pools in woodlands and comparable olive groves, under two contrasting management systems (bare soils versus soil under cover crops) and parent materials (calcareous and siliceous), were explored. The total mineralogy of soil and clay fractions and the soil-clay assemblages were analysed through the decomposition of X-ray diffraction patterns, and were then related to four SOC pools. Total and unprotected SOC was higher in olive groves under cover crops, and this was true independent of the parent material, proving the importance of herbaceous covers in SOC sequestration in woody crops. Some significant correlations between clay minerals and SOC fractions were found. Interestingly, mixed-layer content was correlated with the biochemically protected SOC fraction (r = 0.810, p < 0.05), and this was so even when the partial correlation coefficient was calculated (r = 0.761, p < 0.05). According to the partial correlation networks (PCN), four separated clusters of variables were obtained, which joined into only one at fdr < 0.25. The PCNs supported the direct correlation between mixed-layer content, especially those rich in smectite, and the biochemically protected SOC fraction, suggesting that smectite layers may stabilize organic molecules. Since potassium enrichment is higher in the rooted layers of woodland and soils under cover crops, and this increase is related to the collapse of swelling layers, these soils were poorer in smectite phases than the bare soils. This also would explain why the biochemically protected SOC was more abundant in the latter. [ABSTRACT FROM AUTHOR]

Considering that, in the context of the ecological restoration of a large number of exposed rock slopes, it is difficult for existing artificial soil to meet the requirements of mechanical properties and ecological construction at the same time, this paper investigates the stabilization benefits of polyvinyl acetate and attapulgite-treated clayey soil through a series of laboratory experiments. To study the effectiveness of polyvinyl acetate (PVA) and attapulgite as soil stabilizer, a triaxial strength test, an evaporation test and a vegetation growth test were carried out on improved soil with different amounts of PVA content (0, 1%, 2%, 3%, and 4%) and attapulgite replacement (0, 2%, 4%, 6%, and 8%). The results show that the single and composite materials of polyvinyl acetate and attapulgite can increase the peak deviator stress of the sample. The addition of polyvinyl acetate can improve the soil strength by increasing the cohesion of the sample; the addition of attapulgite improves the soil strength mainly by increasing the internal friction angle of the sample. The strength of the composite is greatly improved by increasing the cohesion and internal friction angle of the sample at the same time. The effect of adding materials increased significantly with increasing curing age. Moreover, polyvinyl acetate and attapulgite improve the soil water retention of the soil by improving the water-holding capacity, so that the soil can still ensure the good growth of vegetation under long-term drought conditions. The scanning electron microscopy (SEM) images indicated that the PVA and attapulgite of soil affect the strength characteristics of soil specimens by the reaction of PVA and water, which changes the structure of the soil and, by the interweaving of attapulgite soil particles, acts as the skeleton of the aggregate. Overall, PVA and attapulgite can effectively increase clayey soil stability by improving the cohesive force and internal friction angle of clayey soil. [ABSTRACT FROM AUTHOR]

Weak subgrade is the main problem facing most highway projects. Therefore, this study focuses on trying to improve the properties and increase the strength of weak, clayey, swelling soil for use as a subgrade for pavement structural sections. This trial was developed using a mix of granular and chemical stabilization for the soil. Granular stabilization was applied firstly by mixing natural sand at different percentages of 20%, 35%, and 50% of the total weight of clayey, swelling soil samples to find the minimum percentage that could be added to improve it to sandy, clayey soil, which is acceptable as a subgrade according to the Egyptian highway specification code. Secondly, chemical stabilization was applied to enhanced sandy, clayey soil to increase its strength properties. This was performed by adding chemical additives (lime, cement kiln dust (CKD), fiberglass, Addicrete 11, and gypsum) at different ratios of 2%, 4%, and 6% of the total weight of the samples of enhanced sandy, clayey soil. An experimental program was conducted consisting of characteristics and consistency tests, the California bearing ratio (CBR) test, a proctor test, and a consolidated-drained (C-D) tri-axial shear test. The results showed that 50% sand was the minimum percentage that could be mixed with swelling, clayey soil for granular stabilization to be enhanced and become sandy, clayey soil, which is accepted as a subgrade layer according to the Egyptian highway specification code. In addition, using a mix of granular and chemical stabilization increased the compressive strength of this enhanced subgrade by adding 6% lime or cement kiln dust (CKD) of the total sample weight. They enhanced the strength of the soil and reduced its plasticity. Adding 6% fiberglass and polymers could slightly enhance the desired properties; however, it is not recommended to use them due to their slight effect and economic cost. In addition, it is not recommended to use gypsum at more than 4% due to its negative effect on CBR. [ABSTRACT FROM AUTHOR]

A large amount of coal fly ash produced in thermal power plants is disposed of in landfills which causes many environmental problems. The utilization of fly ash can be encouraged in geotechnical engineering projects. In this paper, the effects of class C and class F fly ash on the mechanical and microstructural behavior and stabilization of clay soil were evaluated through a program of laboratory experiments. The experiments included compaction, unconfined compressive strength, consolidated-undrained triaxial, one-dimensional consolidation tests, and scanning electron microscopy analysis on samples of fly ash-stabilized clay soil after 1, 7, and 28 days of curing. The tests were conducted on mixtures of clay with class C or class F fly ash, ranging from 0% to 30% of the soil. Experimental results showed that the strength parameters and permeability of the stabilized soil improved while the compression and swelling indices decreased by the addition of fly ash and by the increase of curing days. The results obtained from the mechanical tests agreed with the results from the SEM analysis. Based on the results, the soil could be successfully stabilized by using class C fly ash. The improvements in strength, swelling, and permeability parameters of the stabilized soil were higher with the class C fly ash compared with class F fly ash. [ABSTRACT FROM AUTHOR]

Geopolymers, or also known as alkali-activated binders, have recently emerged as a viable alternative to conventional binders (cement) for soil stabilization. Geopolymers employ alkaline activation of industrial waste to create cementitious products inside treated soils, increasing the clayey soils' mechanical and physical qualities. This paper aims to review the utilization of fly ash and ground granulated blast furnace slag (GGBFS)-based geopolymers for soil stabilization by enhancing strength. Previous research only used one type of precursor: fly ash or GGBFS, but the strength value obtained did not meet the ASTM D 4609 (<0.8 Mpa) standard required for soil-stabilizing criteria of road construction applications. This current research focused on the combination of two types of precursors, which are fly ash and GGBFS. The findings of an unconfined compressive strength (UCS) test on stabilized soil samples were discussed. Finally, the paper concludes that GGBFS and fly-ash-based geo-polymers for soil stabilization techniques can be successfully used as a binder for soil stabilization. However, additional research is required to meet the requirement of ASTM D 4609 standard in road construction applications, particularly in subgrade layers. [ABSTRACT FROM AUTHOR]

This study examines the potential use of sodium alginate (SA) biopolymer as an environmentally sustainable agent for the stabilization of rubberized soil blends prepared using a high plasticity clay soil and tire-derived ground rubber (GR). The experimental program consisted of uniaxial compression and scanning electron microscopy (SEM) tests; the former was performed on three soil-GR blends (with GR-to-soil mass ratios of 0%, 5% and 10%) compacted (and cured for 1, 4, 7 and 14 d) employing distilled water and three SA solutions—prepared at SA-to-water (mass-to-volume) dosage ratios of 5, 10 and 15 g/L—as the compaction liquid. For any given GR content, the greater the SA dosage and/or the longer the curing duration, the higher the uniaxial compressive strength (UCS), with only minor added benefits beyond seven days of curing. This behavior was attributed to the formation and propagation of so-called "cationic bridges" (developed as a result of a "Ca2+/Mg2+ ⟷ Na+ cation exchange/substitution" process among the clay and SA components) between adjacent clay surfaces over time, inducing flocculation of the clay particles. This clay amending mechanism was further verified by means of representative SEM images. Finally, the addition of (and content increase in) GR—which translates to partially replacing the soil clay content with GR particles and hence reducing the number of available attraction sites for the SA molecules to form additional cationic bridges—was found to moderately offset the efficiency of SA treatment. [ABSTRACT FROM AUTHOR]

The research study described in this paper investigated the potential to use steel furnace slag (SFS) as a stabilizing additive for clayey soils. Even though SFS has limited applications in civil engineering infrastructure due to the formation of deleterious expansion in the presence of water, the free CaO and free MgO contents allow for the SFS to be a potentially suitable candidate for clayey soil stabilization and improvement. In this investigation, a kaolinite clay was stabilized with 10% and 15% ladle metallurgy furnace (LMF) slag fines by weight. This experimental study also included testing of the SFS mixtures with the activator calcium chloride (CaCl2), which was hypothesized to accelerate the hydration of the dicalcium silicate phase in the SFS, but the results show that the addition of CaCl2 was not found to be effective. Relative to the unmodified clay, the unconfined compressive strength increased by 67% and 91% when 10% and 15% LMF slag were utilized, respectively. Likewise, the dynamic modulus increased by 212% and 221% by adding 10% and 15% LMF slag, respectively. Specifically, the LMF slag fines are posited to primarily contribute to a mechanical rather than chemical stabilization mechanism. Overall, these findings suggest the effective utilization of SFS as a soil stabilization admixture to overcome problems associated with dispersive soils, but further research is required. [ABSTRACT FROM AUTHOR]

Expansive soil shows dual swell–shrink which is not suitable for construction. Several mitigating techniques exist to counteract the problem promulgated by expansive clayey soils. This paper explored the potential mecho-chemical reinforcement of expansive clayey soil to mitigate the effect of upward swelling pressure and heave. The polypropylene fiber is randomly distributed in the soil for mechanical stabilization, and the industrial residual silica fume is used as a chemical stabilizer. The experimental analysis was made in three phases which involved tests on mechanically-reinforced expansive soil, using randomly distributed polypropylene fibers with different percentages (0.25%, 0.50%, and 1.00%), and which were 12 mm length. The second phase of experiments was carried out on chemical stabilized expansive soil with different percentages (2%, 4%, and 8%) of silica, and the next phase of the experiment focused on the combination of mecho-chemical stabilization of the expansive soil with different combinations of silica (i.e., 2%, 4%, and 8%) and polypropylene fibers (i.e., 0.25%, 0.50%, and 1.00%). Maximum dry density (MDD), optimum moisture content (OMC), liquid limit (LL), plastic limit (PL), plastic index (PI), grain size, and constant volume swelling pressure tests were performed on unreinforced and reinforced expansive soil, to investigate the effects of polypropylene fiber and silica fume on the engineering properties of expansive clayey soil. The experimental results illustrate that the inclusion of polypropylene fiber has a significant effect on the upward swelling pressure and expansion property of expansive soil. The reduction in the upward swelling pressure and expansion is a function of fiber content. These results also indicated that the use of silica fume caused a reduction in upward swelling potential, and its effect was considerably more than the influence of fiber. [ABSTRACT FROM AUTHOR]