Search

Based on the three-dimensional (3D) steady-state CFD numerical simulations conducted previously on an industrial Kalugin top combustion hot blast stove, a two-dimensional (2D) transient CFD numerical model for a single channel (hole) of a column of checker bricks in the regenerator of the same hot stove was established in the present work. The average mass flowrate and temperature of the flue gas flowing into the checker brick holes during the combustion period predicted by the 3D model were used as the inlet boundary conditions of the 2D model. Inside the hole of the checker bricks, processes of fluid flow and heat transfer of the flue gas during the combustion period and those of cold air during the hot-air-supply period were simulated using the 2D model for multiple operation cycles (combustion and hot-air-supply periods) of the hot stove, enabling rapid predictions of hot-air temperature under different operating conditions. The simulation results show that when the fuel gas flowrate and air consumption coefficient during the combustion period are controlled within the range of 80,000–100,000 Nm3/h and 1.02–1.28, respectively, a hot-air temperature in the range from 1273 °C to 1295 °C can be obtained during the hot-air-supply period. Applying this optimized operating condition to the industrial hot stove investigated in this study can achieve significant effects of reducing fuel gas flowrate by 8.6% and increasing hot-air temperature by 32 °C. In addition, a regression analysis on the numerical simulation results and the data measured from the industrial hot stove yields a roughly linear relationship between the dome temperature during the combustion period and the hot-air temperature during the hot-air-supply period, that is, the hot-air temperature would be increased by about 16 °C for every increment of 10 °C in the dome temperature, for instance. Therefore, the influences of the operating parameters on heat transfer characteristics in the regenerator and on hot-air temperature obtained in the present work provide a useful reference for guiding the hot stove operation optimization to achieve significant energy saving and emission reduction through facilitating more efficient combustion to minimize fuel gas consumption in steel plants. [ABSTRACT FROM AUTHOR]

In order to study the behavior of molten blast furnace slag ligament breakup into droplets by centrifugal granulation with a spinning cup, three-dimensional transient CFD model simulations were performed in the present work to study the process of the slag deformation into ligaments upon leaving the spinning cup, which eventually disintegrate into droplets. The formation of molten slag ligaments at the edge of the spinning cup and their disintegration into droplets were numerically revealed so that the behavior and mechanism of the slag ligament breakup into droplets could be investigated. This work specifically examined the influence of cup spinning speed on the diameter and length of the molten slag ligaments around the cup periphery and the diameter of the droplets produced. The simulation results show that, for the same slag flowrate, with the increase in cup spinning speed, the slag film thickness at the cup edge decreases, the number of molten slag ligaments increases, and the diameter of the ligaments decreases, thus reducing the diameter of slag droplets. Moreover, as the number of molten slag ligaments increases as a result of the increased cup spinning speed, the flowrate of a single ligament decreases, so that the ligament disintegrates in a shorter radial distance, that is, the length of the ligament is shortened. In addition, this work also investigated the behavior and mechanism of a single molten slag ligament breakup into droplets. It was found that the process of molten slag ligament breakup into droplets under the action of centrifugal force and surface tension can also be approximately explained by the theory of the Rayleigh disintegration mechanism. [ABSTRACT FROM AUTHOR]

Aiming at the mode of liquid ligament disintegration into droplets in the process of the centrifugal granulation of molten blast furnace slag using a spinning cup, in order to gain an in-depth understanding of the behavior and mechanism of droplet formation by liquid ligament disintegration and to obtain appropriate conditions to control the size of the produced slag granules, a three-dimensional CFD model describing water–air two-phase flow with a free surface was established in this work for simulating the process of a single water ligament breakup into droplets under the action of gravity, surface tension and inertial forces, so as to compare with the process of a molten slag ligament disintegration into droplets due to centrifugal force exerted by the spinning cup. By studying the disintegration behavior and mechanism of a single water ligament, the similar phenomenon of a molten slag ligament disintegration is examined. The numerical simulation results on the breakup of a single water ligament show that the length of the ligament before its disintegration and the diameter of the droplets formed both increase with the increase of the velocity of the ligament initially exiting a capillary nozzle. In addition, an experimental set-up was established in the laboratory to conduct cold physical model simulation experiments on single water or liquid paraffin ligament disintegration. The experimental results are compared with the numerical simulation results so that the reliability of the CFD model is verified. The results of the present study show that, in the centrifugal granulation process of blast furnace slag using a spinning cup operated in the ligament disintegration mode, the breakup of a single molten slag ligament is very similar to that of a single water or liquid paraffin ligament, and both approximately follow the Rayleigh Disintegration Mechanism, which provides a theoretical basis for analyzing the breakup process of the ligaments of different liquids as references for guiding the operation of centrifugal granulation of molten slag. [ABSTRACT FROM AUTHOR]