Search

This article proposes a new type of three-component optic fiber balance based on Fabry–Perot displacement measurement technology based on the structure of the pulse wind tunnel balance. This paper systematically introduces the force measurement principle and design process of a three-component optic fiber balance and conducts relevant simulation analysis and experimental verification. The simulation results show that the Fabry–Perot sensor can achieve significant sensitivity to cavity length changes, and when used in existing balance structures, sensitivity gains can be achieved by changing the probe height without the need to modify the original structure of the balance. Finally, the feasibility of the design method was verified through calibration experiments: the optic fiber balance has high sensitivity and good linearity compared to simulation sensitivity, the error is less than 6%, and the calibration accuracy of each component is better than 0.13%, which is better than the existing traditional strain balance (0.37%). The pulse wind tunnel force measurement test has a short test time and a large model mass, and the balance needs to have a large stiffness to meet the short-term force measurement requirements. The introduction of more sensitive optic fiber balance force measurement technology is expected to solve the contradiction between the stiffness and sensitivity of force measurement systems. [ABSTRACT FROM AUTHOR]

The structure used in this study is as follows: substrate/PMMA/ZnS/Ag/MoO3/NPB/Alq3/LiF/Al. Here, PMMA serves as the surface flattening layer, ZnS/Ag/MoO3 as the anode, NPB as the hole injection layer, Alq3 as the emitting layer, LiF as the electron injection layer, and aluminum as the cathode. The properties of the devices with different substrates were investigated using P4 and glass, developed in the laboratory, as well as commercially available PET. After film formation, P4 creates holes on the surface. The light field distribution of the device was calculated at wavelengths of 480 nm, 550 nm, and 620 nm using optical simulation. It was found that this microstructure contributes to light extraction. The maximum brightness, external quantum efficiency, and current efficiency of the device at a P4 thickness of 2.6 μm were 72,500 cd/m2, 1.69%, and 5.68 cd/A, respectively. However, the maximum brightness of the same structure with PET (130 μm) was 9500 cd/m2. The microstructure of the P4 substrate was found to contribute to the excellent device performance through analysis of the AFM surface morphology, film resistance, and optical simulation results. The holes formed by the P4 substrate were created solely by spin-coating the material and then placing it on a heating plate to dry, without any special processing. To confirm the reproducibility of the naturally formed holes, devices were fabricated again with three different emitting layer thicknesses. The maximum brightness, external quantum efficiency, and current efficiency of the device at an Alq3 thickness of 55 nm were 93,400 cd/m2, 1.7%, and 5.6 cd/A, respectively. [ABSTRACT FROM AUTHOR]

Coronary computed tomography angiography (CCTA) is a widely used imaging modality for diagnosing coronary artery disease (CAD) but is limited by a high false positive rate when evaluating coronary arteries with stents and heavy calcifications. Virtual intravascular endoscopy (VIE) images generated from CCTA can be used to qualitatively assess the vascular lumen and might be helpful for overcoming this challenge. In this study, one hundred subjects with coronary stents underwent both CCTA and invasive coronary angiography (ICA). A total of 902 vessel segments were analyzed using CCTA and VIE. The vessel segments were first analyzed on CCTA alone. Then, using VIE, the segments were classified qualitatively as either negative or positive for in-stent restenosis (ISR) or CAD. These results were compared, using ICA as the reference, to determine the added diagnostic value of VIE. Of the 902 analyzed vessel segments, CCTA/VIE had sensitivity, specificity, accuracy, positive predictive value, and negative predictive value (shown in %) of 93.9/90.2, 96.2/98.2, 96.0/97.7, 70.0/83.1, and 99.4/99.0, respectively, in diagnosing ISR or CAD, with significantly improved specificity (p = 0.025), accuracy (p = 0.046), and positive predictive value (p = 0.047). VIE can be a helpful addition to CCTA when evaluating coronary arteries. [ABSTRACT FROM AUTHOR]

In this study, we proposed using the high-K polyvinyl alcohol (PVA)/low-K poly-4-vinylphenol (PVP) bilayer structure as the gate insulator to improve the performance of a pentacene-based organic thin-film transistor. The dielectric constant of the optimal high-K PVA/low-K PVP bilayer was 5.6, which was higher than that of the single PVP layer. It resulted in an increase in the gate capacitance and an increased drain current. The surface morphology of the bilayer gate dielectric could be suitable for pentacene grain growth because the PVP layer was deposited above the organic PVA surface, thereby replacing the inorganic surface of the ITO gate electrode. The device performances were significantly improved by using the bilayer gate dielectric based upon the high-K characteristics of the PVA layer and the enlargement of the pentacene grain. Notably, the field-effect mobility was increased from 0.16 to 1.12 cm2/(Vs), 7 times higher than that of the control sample. [ABSTRACT FROM AUTHOR]

Inherited cardiac conduction disease (CCD) is rare; it is caused by a large number of mutations in genes encoding cardiac ion channels and cytoskeletal proteins. Recently, whole-exome sequencing has been successfully used to identify causal mutations for rare monogenic Mendelian diseases. We used trio-based whole-exome sequencing to study a Chinese family with multiple family members affected by CCD, and identified a heterozygous missense mutation (c.343C>T, p.Leu115Phe) in the desmin (DES) gene as the most likely candidate causal mutation for the development of CCD in this family. The mutation is novel and is predicted to affect the conformation of the coiled-coil rod domain of DES according to structural model prediction. Its pathogenicity in desmin protein aggregation was further confirmed by expressing the mutation, both in a cellular model and a CRISPR/CAS9 knock-in mouse model. In conclusion, our results suggest that whole-exome sequencing is a feasible approach to identify candidate genes underlying inherited conduction diseases. [ABSTRACT FROM AUTHOR]

Background: Nail changes, including onychomadesis (nail shedding) and Beau's line, following hand-foot-mouth disease (HFMD) are a common emergence at the stage of late complications of HFMD. However, the exact mechanism is still unknown. Therefore, we conducted this study to elucidate the mechanism of nail changes following HFMD. Methods: We collected 11 patients suffering from onychomadesis following HFMD. Nail samples from all of them were collected. Real time reverse transcription polymerase chain reaction (RT-PCR) and sequencing for human enteroviruses (HEV) were performed. Throat swabs for RT-PCR and sequencing for HEV were performed for three cases. Results: RT-PCR demonstrated the presence of Coxackievirus A6 (CVA6) in nail samples from three patients and one with Echovirus. Conclusion: In conclusion, we believe that the major cause of onychomadesis following HFMD is that certain novel viruses, mostly CVA6, are virulent and may damage nail matrix. Direct injury caused by cutaneous lesions of HFMD around nail matrix is a minor cause. There are still other virulent HEV which may result in onychomadesis. In addition, the novel strain of CVA6 also causes atypical clinical presentations, such as adult involvement and delayed-onset palmar and plantar desquamation. Physicians should be familiar with atypical presentations caused by novel viruses to avoid misdiagnosis and even inform patients of the possibility of onychomadesis that may take place weeks later to reassure patients. [ABSTRACT FROM AUTHOR]