Search

This study investigates the mechanism and effects of incorporating different ZrO2 nano-particles into SAC0307 solder alloys. ZrO2 nano-powder and nano-fibers in 0.25–0.5 wt% were added to the SAC0307 alloy to prepare composite solder joints by surface mount technology. The solder joints were shear tested before and after a 4000 h long 85 °C/85% RH corrosive reliability test. The incorporation of ZrO2 nano-particles enhanced the initial shear force of the solder joint, but they decreased the corrosion resistance in the case of 0.5 wt%. SEM, EDS, and FIB analysis revealed intensive growth of SnO2 on the solder joint surfaces, leading to the formation of Sn whiskers. Density functional theory (DFT) simulations showed that, despite Sn being able to bond to the surface of ZrO2, the binding energy was weak, and the whole system was therefore unstable. It was also found that ZrO2 nano-particles refined the microstructure of the solder joints. Decreased β-Sn grain size and more dispersed intermetallic compounds were observed. The microstructural refinement caused mechanical improvement of the ZrO2 composite solder joints by dispersion strengthening but could also decrease their corrosion resistance. While ZrO2 nano-particles improved the solder joint mechanical properties, their use is recommended only in non-corrosive environments, such as microelectronics for space applications. [ABSTRACT FROM AUTHOR]

Novel Au nano-particle catalysts immobilized on both titanium(IV)- and alkylthiol-functionalized SBA-15 type ordered mesoporous silicate supports were developed. The bi-functionalized SBA-15 type support could be synthesized by a one-pot method. To the synthesized supports, Au was immobilized by the reaction of the alkylthiol groups on the supports with AuCl4−, following reduction with NaBH4. The immobilized amount and the formed structures and the electronic property of the Au species depended on the loading of alkylthiol. The moderate size (2–3 nm) nano particulate Au sites formed on Ti(0.5)-SBASH(0.5) were negatively charged. The aerobic alcohol oxidation activity of the catalysts depended on the loading of alkylthiol and the structure of the Au nano-particles. The non-thiol-functionalized catalyst (Au/Ti(0.5)-SBASH(0)) composed of the large (5–30 nm) and the higher thiol-loaded catalyst (Au/Ti(0.5)-SBASH(8)) composed of the small cationic Au species were almost inactive. The most active catalyst was Au/Ti(0.5)-SBASH(0.5) composed of the electron-rich Au nano-particles formed by the electron donation from the highly dispersed thiol groups. Styrene oxidation activity in the presence of 1-phenylethanol with O2 depended on the loadings of titanium(IV) on the Au/Ti(x)-SBASH(0.5). The titanium(IV) sites trapped the H2O2 generated through the alcohol oxidation reaction, and also contributed to the alkene oxidation by activating the trapped H2O2. [ABSTRACT FROM AUTHOR]

Implants and other medical devices are prone to bacterial infections on their surface due to bacterial attachment and biofilm formation. In this study, silver nanoparticles were generated in situ onto regulated synthesized polydopamine particles, and the optimal amount of silver nitrate was determined. Composite micro–nano particles were then deposited on a titanium alloy surface. X-ray photoelectron spectroscopy and energy-dispersive X-ray spectroscopy were used to confirm that the titanium alloy surface was successfully coated with PDA-Ag. Scanning electron microscopy, transmission electron microscopy, and three-dimensional optical profilometry were utilized to analysis the morphology of the micro–nano particles and the surface morphology after deposition. The diameters of the polydopamine particles and silver nanoparticles were 150 nm and 25 nm, respectively. The surface roughness values decreased from 0.357 μm to 25.253 μm because of the coated PDA-Ag. Morphology and chemical composition analyses of the modified surface indicated that the PDA-Ag particles were uniformly bonded to the substrate surface. Antimicrobial assays illustrated that the PDA-Ag-modified surface possessed resistance against Escherichia coli and Staphylococcus aureus attachment, with an effectiveness of 96.14 and 85.78%, respectively. This work provides a new strategy and theoretical basis for tackling medical-related surface infections caused by bacterial adhesion. [ABSTRACT FROM AUTHOR]

Tailor-made and designed micro- and nanocarriers can bring significant benefits over their traditional macroscopic counterparts in drug delivery applications. For the successful loading and subsequent release of bioactive compounds, carriers should present a high loading capacity, trigger release mechanisms, biodegradability and biocompatibility. Hydrophobic drug molecules can accumulate in fat tissues, resulting in drawbacks for the patient's recovery. To address these issues, we propose to combine the advantageous features of both host molecules (cyclodextrin) and calcium carbonate (CaCO3) particles in order to load hydrophobic chemicals. Herein, hybrid cyclodextrin-CaCO3 micro- to nano-particles have been fabricated by combining Na2CO3 solution and CaCl2 solution in the presence of an additive, namely poly (vinylsulfonic acid) (PVSA) or glycerol (gly). By investigating experimental parameters and keeping the Na2CO3 and CaCl2 concentrations constant (0.33 M), we have evidenced that the PVSA or gly concentration and mixing time have a direct impact on the final cyclodextrine-CaCO3 particle size. Indeed, by increasing the concentration of PVSA (5 mM to 30 mM) or gly (0.7 mM to 4 mM) or the reaction time (from 10 min to 4 h), particles with a size of 200 nm could be reached. Interestingly, the vaterite or calcite form could also be selected, according to the experimental conditions. We hypothesised that the incorporation of PVSA or gly into the precipitation reaction might reduce the nucleation rate by sequestering Ca2+. The obtained particles have been found to keep their crystal structure and surface charge after storage in aqueous media for at least 6 months. In the context of improving the therapeutic benefit of hydrophobic drugs, the developed particles were used to load the hydrophobic drug tocopherol acetate. The resulting particles are biocompatible and highly stable in a physiological environment (pH 7.4, 0.15 M NaCl). A selective release of the cargo is observed in acidic media (pH lower than 5). [ABSTRACT FROM AUTHOR]

Additive manufacturing (AM) or industrial 3D printing uses cutting-edge technologies and materials to produce a variety of complex products. However, the effects of the unintentionally emitted AM (nano)particles (AMPs) on human cells following inhalation, require further investigations. The physicochemical characterization of the AMPs, extracted from the filter of a Laser Powder Bed Fusion (L-PBF) 3D printer of iron-based materials, disclosed their complexity, in terms of size, shape, and chemistry. Cell Painting, a high-content screening (HCS) assay, was used to detect the subtle morphological changes elicited by the AMPs at the single cell resolution. The profiling of the cell morphological phenotypes, disclosed prominent concentration-dependent effects on the cytoskeleton, mitochondria, and the membranous structures of the cell. Furthermore, lipidomics confirmed that the AMPs induced the extensive membrane remodeling in the lung epithelial and macrophage co-culture cell model. To further elucidate the biological mechanisms of action, the targeted metabolomics unveiled several inflammation-related metabolites regulating the cell response to the AMP exposure. Overall, the AMP exposure led to the internalization, oxidative stress, cytoskeleton disruption, mitochondrial activation, membrane remodeling, and metabolic reprogramming of the lung epithelial cells and macrophages. We propose the approach of integrating Cell Painting with metabolomics and lipidomics, as an advanced nanosafety methodology, increasing the ability to capture the cellular and molecular phenotypes and the relevant biological mechanisms to the (nano)particle exposure. [ABSTRACT FROM AUTHOR]

This article is an attempt to explore the heat transfer features of the steady three-dimensional rotating flow of magneto-hydrodynamic hybrid nanofluids under the effect of nonlinear radiation over the bi-directional stretching surface. For this purpose, two different nano-particles, namely silver (Ag) and molybdenum di-sulfide (MoS2), were selected. Three different conventional base fluids were utilized to form desired hybrid nanofluids such as water (H2O), engine oil (EO), and ethylene glycol (EG). We obtained steady three-dimensional highly nonlinear partial differential equations. These highly nonlinear partial differential equations cannot be solved analytically, so these equations were handled in MATLAB with the BVP-4C technique with convergence tolerance at 10−6. The graph depicts the effect of the magnetization effect, thermal radiation, and stretching ratio on rotating hybrid nanofluids. Additionally, the impact of thermal radiation on the heat coefficient of three different hybrid nanofluids is being investigated. The augmentation in magnetization decreases the primary velocity, whereas the increment in radiation enhances the primary velocity. The stretching ratio and the presence of higher magnetic forces increase the temperature profile. The concentration profile was enhanced with an increment in the magnetic field, stretching, and rotation ratio. The maximum Nusselt number was achieved for the Ag-MoS2/EO hybrid nanofluid. It was concluded that augmentation in nonlinear radiation enhances the heat transfer coefficient for the examined cases (I) and (II) of the hybrid nanofluids. The Nusselt number doubled for both the examined cases under nonlinear radiation. Moreover, it was discovered that Ag-MoS2/water produced the best heat transfer results under nonlinear radiation. Therefore, the study recommends more frequent exploration of hybrid nanofluids (Ag-MoS2/water) when employing nonlinear radiation to analyze the heat transfer coefficient. [ABSTRACT FROM AUTHOR]

Experimental and numerical experiments were carried out to study the coffee rings or coffee splats formed by droplet evaporation with micro or nano polystyrene sphere particles (Dp = 10 μm or 100 nm). Particle image velocimetry (PIV) and a high-resolution camera were used in this experiment, along with a temperature-controlled heater and a data-acquisition computer. The results showed that a nano particle could form a homogeneous coffee splat, instead of the common coffee ring formed when using micro particles. In order to account for this phenomenon, this paper developed a complex multiphase model, one which included the smooth particle hydrodynamics (SPH) fluid model coupled with the van der Waals equation of state for droplet evaporation, the rigid particle model of finite-size micro particles, and the point–particle model of the nanometer particles. The numerical simulation was operated on a GPU-based algorithm and tested by four validation cases. A GPU could calculate 533 times the speed of a single-core CPU for about 300,000 particles. The results showed that, for rigid solid particles, the forms emerged spontaneously on the wall, and their structure was mainly affected by the boundary wettability, and less affected by the fluid flow and thermal condition. When the wall temperature was low, it was easier for the particles to be deposited on the contact line. At high wall temperature, the coffee ring effect would be weakened, and the particles were more likely to be deposited in the droplet center. The hydrophilic surface produced a larger coffee ring compared to the hydrophobic surface. The experimental and numerical results proved that particle size could play a significant role during the particle deposition, which may be a possible route for producing uniform-distributed and nano-structure coatings. [ABSTRACT FROM AUTHOR]

There are significant societal repercussions from our excessive use of plastic products derived from petroleum. In response to the increasing environmental implications of plastic wastes, biodegradable materials have been proven to be an effective means of mitigating environmental issues. Therefore, protein- and polysaccharide-based polymers have gained widespread attention recently. In our study, for increasing the strength of a biopolymer (Starch), we used ZnO dispersed nanoparticles (NPs), which resulted in the enhancement of other functional properties of the polymer. The synthesized NPs were characterized using SEM, XRD, and Zeta potential values. The preparation techniques are completely green, with no hazardous chemicals employed. The floral extract employed in this study is Torenia fournieri (TFE), which is prepared using a mixture of ethanol and water and possesses diverse bioactive features and pH-sensitive characteristics. The prepared films were characterized using SEM, XRD, FTIR, contact angle and TGA. The incorporation of TFE and ZnO (SEZ) NPs was found to increase the overall nature of the control film. The results obtained from this study confirmed that the developed material is suitable for wound healing and can also be used as a smart packaging material. [ABSTRACT FROM AUTHOR]

The most successful medical intervention for preventing infectious diseases is still vaccination. This effective strategy has resulted in decreased mortality and extended life expectancy. However, there is still a critical need for novel vaccination strategies and vaccines. Antigen cargo delivery by nanoparticle-based carriers could promote superior protection against constantly emerging viruses and subsequent diseases. This should be sustained by the induction of vigorous cellular and humoral immunity, capable of acting both at the systemic and mucosal levels. Induction of antigen-specific responses at the portal of entry of pathogens is considered an important scientific challenge. Chitosan, which is widely regarded as a biodegradable, biocompatible and non-toxic material for functionalized nanocarriers, as well as having adjuvant activity, enables antigen administration via less-invasive mucosal routes such as sublingual or pulmonic application route. In this proof of principle study, we evaluate the efficacy of chitosan nanocarriers loaded with the model antigen Ovalbumin (OVA) co-administrated with the STING agonist bis-(3′,5′)-cyclic dimeric adenosine monophosphate (c-di-AMP) given by pulmonary route. Here, BALB/c mice were immunized with four doses of the formulation that stimulates enhanced antigen-specific IgG titers in sera. In addition, this vaccine formulation also promotes a strong Th1/Th17 response characterized by high secretion of IFN-γ, IL-2 and IL-17, as well as induction of CD8+ T cells. Furthermore, the novel formulation exhibited strong dose-sparing capacity, enabling a 90% reduction of the antigen concentration. Altogether, our results suggest that chitosan nanocarriers, in combination with the mucosal adjuvant c-di-AMP, are a promising technology platform for the development of innovative mucosal vaccines against respiratory pathogens (e.g., Influenza or RSV) or for therapeutic vaccines. [ABSTRACT FROM AUTHOR]

Nano-particles and fibers-modified cementitious composite (NFCC) can greatly overcome the shortcomings of traditional cementitious materials, such as high brittleness and low toughness, and improve the durability of the composite, which in turn increases the service life of the structures. Additionally, the polymer coatings covering the surface of the composite can exert a good physical shielding effect on the external water, ions, and gases, so as to improve the permeability and chloride ion penetration resistance of the composite. In this study, the effect of three types of polymer coatings on the water contact angle, permeability resistance, and chloride ion penetration resistance of the NFCC with varied water–binder ratios were investigated. Three kinds of polymers (chlorinated rubber coating, polyurethane coating, and silane coating) were applied in two types of coatings, including single-layer and double-layer coatings. Three water–binder ratios of 35 wt.%, 40 wt.%, and 45 wt.% were used for the NFCC. The research results revealed that the surface of the NFCC treated with polymer coatings exhibited excellent hydrophobicity. The permeability height and chloride diffusion coefficient of the NFCC coated with different types of polymer coatings were 31–48% and 36–47% lower, respectively, than those of the NFCC without polymer coatings. The durability of the NFCC was further improved when the polymer coatings were applied to the surface in two-layer. Furthermore, it was discovered that increasing the water–binder ratio of the NFCC would lessen the positive impact of polymer coatings on the durability of NFCC. [ABSTRACT FROM AUTHOR]

With the rapid development of metal-organic frameworks (MOF), the toxicity and environmental safety of MOF materials should be thoroughly investigated. The behaviors and bio-effects of MOF materials after oral exposure are largely unknown. In this study, we performed a pilot toxicity evaluation of MOF-74(Co) nanoparticles (NPs) both in vitro and in vivo. The cell viability and cell cycle were monitored after LO2 cells were incubated with MOF-74(Co). The Co contents, bodyweight, serum biochemistry, histopathological changes, and oxidative stress parameters were measured after oral exposure to MOF-74(Co) NPs in mice. LO2 cells showed viability loss at 100 mg/L. The cell cycle arrest was more sensitive, which was observed even at 12.5 mg/L. MOF-74(Co) NPs led to a significant accumulation of Co in the liver and kidneys. No bodyweight loss was observed and the serum biochemical index was mainly unchanged. Except for slight inflammation, the histopathological images of the liver and kidneys after oral exposure to MOF-74(Co) NPs were normal compared to the control. Meaningful oxidative stress was found in the liver and kidneys. The results collectively indicated the low toxicity of MOF-74(Co) NPs after oral exposure in mice. [ABSTRACT FROM AUTHOR]

The creation of novel anticancer treatments for a variety of human illnesses, including different malignancies and dangerous microbes, also potentially depends on nanoparticles including silver. Recently, it has been successful to biologically synthesize metal nanoparticles using plant extracts. The natural flavonoid 3,3′, 4′, 5,5′, and 7 hexahydroxyflavon (myricetin) has anticancer properties. There is not much known about the regulatory effects of myricetin on the possible cell fate-determination mechanisms (such as apoptosis/proliferation) in colorectal cancer. Because the majority of investigations related to the anticancer activity of myricetin have dominantly focused on the enhancement of tumor cell uncontrolled growth (i.e., apoptosis). Thus, we have decided to explore the potential myricetin interactors and the associated biological functions by using an in-silico approach. Then, we focused on the main goal of the work which involved the synthesis of silver nanoparticles and the labeling of myricetin with it. The synthesized silver nanoparticles were examined using UV-visible spectroscopy, dynamic light scattering spectroscopy, Fourier transform infrared spectroscopy, and scanning electron microscopy. In this study, we have investigated the effects of myricetin on colorectal cancer where numerous techniques were used to show myricetin's effect on colon cancer cells. Transmission Electron Microscopy was employed to monitor morphological changes. Furthermore, we have combined the results of the colorectal cancer gene expression dataset with those of the myricetin interactors and pathways. Based on the results, we conclude that myricetin is able to efficiently kill human colorectal cancer cell lines. Since, it shares important biological roles and possible route components and this myricetin may be a promising herbal treatment for colorectal cancer as per an in-silico analysis of the TCGA dataset. [ABSTRACT FROM AUTHOR]

Superhydrophobic nanocomposite coatings, prepared using adhesive and fillers, offer advantages including ease of fabrication and suitability for large-scale applications, but compared with other types of artificial superhydrophobic surfaces, poor durability still limits these surfaces from practical applications. The utilization of micro/nanoscale particles with both intrinsic hydrophobicity and robust mechanical properties to prepare coatings should significantly contribute to enhanced durability. Herein, rough and hydrophobic particles with micro/nano hierarchical structures were prepared at first, and robust superhydrophobic surfaces were fabricated using the prepared particles and additional nanoparticles. The initially prepared particles formed a rough framework of the coating, while additional nanoparticles provided inevitable nanoscale structures. A series of mechanical tests were carried out to validate the durability, and the surface with 20 wt.% NPs exhibited the best performance, withstanding 30 tape peeling tests, a 2.47 m sandpaper rubbing test (at a pressure of 5 kPa), the impact of 200 g of grit dropped from a height of 20 cm, and a 2 h acidic immersion. These appealing materials may attract attention for self-cleaning, high-speed water impact resistance, anti-icing, and anti-fouling applications in the coatings industry. [ABSTRACT FROM AUTHOR]

Novel hydrogels were prepared by blending chitosan and poly(vinyl alcohol), PVA, then crosslinking the resulting blends using trimellitic anhydride isothiocyanate at a concentration based on chitosan content in the blends. The weight ratios of chitosan: PVA in the blends were 1:3, 1:1, and 3:1 to produce three hydrogels symbolized as H13, H11, and H31, respectively. For a comparison, H10 was also prepared by crosslinking pure chitosan with trimellitic anhydride isothiocyanate. For further modification, three H31/silver nanocomposites (AgNPs) were synthesized using three different concentrations of silver nitrate to obtain H31/AgNPs1%, H31/AgNPs3% and H31/AgNPs5%. The structures of the prepared samples were emphasized using various analytical techniques. PVA has no inhibition activity against the tested microbes and biofilms. The antimicrobial and anti-biofilm formation activities of the investigated samples was arranged as: H31/AgNPs5% ≥ H31/AgNPs3% > H31/AgNPs1% > H10 > H31 > H11 > H13 > chitosan. H31/AgNPs5% and H31/AgNPs3% were more potent than Vancomycin and Amphotericin B against most of the tested microbes. Interestingly, H31 and H31/AgNPs3% were safe on the normal human cells. Consequently, hydrogels resulting from crosslinked blends of chitosan and PVA loaded with AgNPs in the same structure have significantly reinforced the antimicrobial and inhibition activity against the biofilms of PVA. [ABSTRACT FROM AUTHOR]

The amount of by-products/waste in the fish industry is roughly 50%. Fish bones could be used to produce nanoparticles, which may have potential use in the food industry as a novel calcium source and at the same time, contribute to reduce waste production. The objective of this study was to evaluate the bioavailability of nano-size salmon fish bone particles compared to micro-size salmon fish bone particles, and calcium carbonate. The study was carried out in 21–28-day-old C57BL/6 male mice fed for 21 days with the experimental diets. The groups were as follows: CaCO3 0.5% Ca (CN 0.5); CaCO3 1.0% Ca (CN 1.0); salmon fish bone (SFB) microparticles 0.5% Ca (MP 0.5); SFB microparticles 1.0% Ca (MP 1.0); SFB nanoparticles 0.5% Ca (NP 0.5); and SFB nanoparticles 1.0% Ca (NP 1.0). Calcium bioavailability, defined as the percent calcium in femur showed an increasing trend from CN 0.5 to NP 1.0 group. According to ANCOVA, the greatest Ca content was observed in the NP 1.0 group compared with all groups but NP 0.5. In conclusion, in a murine model, salmon fish bone nanoparticles present higher calcium bioavailability than salmon fish bone microparticles, and both, in turn, have better bioavailability than calcium carbonate. [ABSTRACT FROM AUTHOR]

Silver nanoparticles (AgNPs) are extensively used in many industries due to their superior antimicrobial properties. However, it is evident from many studies that AgNPs has cytotoxic potential through its effect on excessive formation of reactive oxygen species (ROS). The aim of this study was to examine the toxic effect of AgNPs on the submandibular salivary glands and the attenuating effect of vitamin E, as a natural antioxidant, against this toxicity. Thirty Albino rats were divided into 3 groups (n = 10): control group, AgNPs group receiving 2 mg/kg daily for 28 days, and AgNPs and vitamin E group receiving AgNPs the same as the previous group in addition to vitamin E at a dose of 100 mg/kg. Microscopic, ultrastructural, and cytokeratin immune-reactivity examination of the glands were performed. The AgNPs group showed noticeable degeneration in all structures of the gland as evident in the histological and ultrastructural examination. The AgNPs and vitamin E group revealed an improvement of the glandular elements. A significant increase in cytokeratin immune expression was found after comparison of both groups (p = 0.01). This current study shows that vitamin E has powerful antioxidant properties, which can combat the cytotoxic effect caused by AgNPs. Further studies are deemed necessary to confirm this finding using other immunohistochemical markers, such as myosin and E-cadherin. [ABSTRACT FROM AUTHOR]

This study explores the impact of silica nanoparticles on jute fiber-reinforced composites with epoxy resin matrices. Silica nanoparticles were synthesized at three concentrations (3%, 6%, and 9%) and incorporated into composites at varying fiber–resin weight ratios. The composites were subjected to tests for tensile strength, flexural strength, impact strength, and hardness. The Taguchi signal-to-noise ratio method was employed for optimization. Results indicate that a 9% addition of silica nanoparticles significantly enhances the mechanical properties of jute fiber-reinforced composites. Tensile and flexural strength increased with higher silica nanoparticle content, while impact strength and hardness also improved. Notably, a 9% silica addition achieved a maximum tensile strength of 72 MPa, resulting in a 10% increase over that yielded by the 3% addition. Flexural and impact strengths improved by 23% and 20%, respectively, when compared to the 3% silica addition. Furthermore, a neural network model accurately predicted the composite's mechanical characteristics with 100% accuracy. These findings hold promise for the automobile and aircraft industries, as they require high-performance materials. The integration of jute fibers and silica nanoparticles into composites offers a sustainable and eco-friendly alternative to conventional materials. The enhancement strategy employed in this analysis can be applied to enhance the mechanical properties of other composite materials. [ABSTRACT FROM AUTHOR]

The exposure of human lung and skin to carbon black (CB) is continuous due to its widespread applications. Current toxicological testing uses 'healthy' cellular systems; however, questions remain whether this mimics the everyday stresses that human cells are exposed to, including infection. Staphylococcus aureus lung and skin infections remain prevalent in society, and include pneumonia and atopic dermatitis, respectively, but current in vitro toxicological testing does not consider infection stress. Therefore, investigating the effects of CB co-exposure in 'stressed' infected epithelial cells in vitro may better approximate true toxicity. This work aims to study the impact of CB exposure during Staphylococcus aureus infection stress in A549 (lung) and HaCaT (skin) epithelial cells. Physicochemical characterisation of CB confirmed its dramatic polydispersity and potential to aggregate. CB significantly inhibited S. aureus growth in cell culture media. CB did not induce cytokines or antimicrobial peptides from lung and skin epithelial cells, when given alone, but did reduce HaCaT and A549 cell viability to 55% and 77%, respectively. In contrast, S. aureus induced a robust interleukin (IL)-8 response in both lung and skin epithelial cells. IL-6 and human beta defensin (hβD)-2 could only be detected when cells were stimulated with S. aureus with no decreases in cell viability. However, co-exposure to CB (100 µg/mL) and S. aureus resulted in significant inhibition of IL-8 (compared to S. aureus alone) without further reduction in cell viability. Furthermore, the same co-exposure induced significantly more hβD-2 (compared to S. aureus alone). This work confirms that toxicological testing in healthy versus stressed cells gives significantly different responses. This has significant implications for toxicological testing and suggests that cell stresses (including infection) should be included in current models to better represent the diversity of cell viabilities found in lung and skin within a general population. This model will have significant application when estimating CB exposure in at-risk groups, such as factory workers, the elderly, and the immunocompromised. [ABSTRACT FROM AUTHOR]

Solution electrospinning process (SEP) is a versatile technique for generating non-woven fibrous materials intended to a wide range of applications. One of them is the production of fibrous and porous scaffolds aiming to mimic bone tissue, as artificial extracellular matrices (ECM). In the present work, pure and nano-modified electrospun polyetherimide (PEI) scafolds have been successfully fabricated. The nano-modified ones include (a) graphene nano-platelets (GNPs), (b) hydroxyapatite (HAP), and (c) mixture of both. After fabrication, the morphological characteristics of these scaffolds were revealed by using scanning electron (SEM) and transmission electron (TEM) microscopies, while porosity and mean fiber diameter were also calculated. In parallel, contact angle experiments were conducted so that the hydrophilicity level of these materials to be determined. Finally, the mechanical performance of the fabricated scaffolds was investigated by conducting uniaxial tensile tests. In future work, the fabricated scaffolds will be further utilized for investigation as potential candidate materials for cell culture with perspective in orthopedic applications. [ABSTRACT FROM AUTHOR]

Antibiotic resistance has posed a major public health challenge because of antibiotics misuse, overdose, underdose, ignorance of antibiotics usage and substandard production from producers, thus entailing the need for an alternative antibiotic agent production. Here, a commonly used antibiotic plant, Chrysophyllum albidum leaf, was used to produce silver nanoparticles (AgNPs) and was characterized using XRD, FTIR, DSC and DLS. The characterization data showed the production of six (6)-week stable AgNPs, with high antioxidant properties and amylase, glucosidase and cholinesterases inhibition properties. Similarly, the product exhibited stable antibiotics properties on Escherichia coli, Klebsiella pneumoniae and Staphylococcus aureus after six (6) weeks of storage at 4 °C. [ABSTRACT FROM AUTHOR]

To prevent soiling of marble exposed outdoors, the use of TiO2 nano-particles has been proposed in the literature by two main routes, both raising durability issues: (i) direct application to marble surface, with the risk of particle leaching by rainfall; (ii) particle incorporation into inorganic or organic coatings, with the risk of organic coating degradation catalyzed by TiO2 photoactivity. Here, we investigated the combination of nano-TiO2 and hydroxyapatite (HAP), previously developed for marble protection against dissolution in rain and mechanical consolidation. HAP-TiO2 combination was investigated by two routes: (i) sequential application of HAP followed by nano-TiO2 (“H+T”); (ii) simultaneous application by introducing nano-TiO2 into the phosphate solution used to form HAP (“HT”). The self-cleaning ability was evaluated before and after prolonged exposure to simulated rain. “H+T” and “HT” coatings exhibited much better resistance to nano-TiO2 leaching by rain, compared to TiO2 alone. In “H+T” samples, TiO2 nano-particles adhere better to HAP (having flower-like morphology and high specific surface area) than to marble. In “HT” samples, thanks to chemical bonds between nano-TiO2 and HAP, the particles are firmly incorporated in the HAP coating, which protects them from leaching by rain, without diminishing their photoactivity and without being degraded by them. [ABSTRACT FROM AUTHOR]

We demonstrate in situ recorded motion of nano-objects adsorbed on a photosensitive polymer film. The motion is induced by a mass transport of the underlying photoresponsive polymer material occurring during irradiation with interference pattern. The polymer film contains azobenzene molecules that undergo reversible photoisomerization reaction from trans- to cis-conformation. Through a multi-scale chain of physico-chemical processes, this finally results in the macro-deformations of the film due to the changing elastic properties of polymer. The topographical deformation of the polymer surface is sensitive to a local distribution of the electrical field vector that allows for the generation of dynamic changes in the surface topography during irradiation with different light interference patterns. Polymer film deformation together with the motion of the adsorbed nano-particles are recorded using a homemade set-up combining an optical part for the generation of interference patterns and an atomic force microscope for acquiring the surface deformation. The particles undergo either translational or rotational motion. The direction of particle motion is towards the topography minima and opposite to the mass transport within the polymer film. The ability to relocate particles by photo-induced dynamic topography fluctuation offers a way for a non-contact simultaneous manipulation of a large number of adsorbed particles just in air at ambient conditions. [ABSTRACT FROM AUTHOR]

We investigate the optomechanical effect on a single nano-particle inside an optical cavity, by deriving the optical forces acting on the nano-particle by the cavity from quantum theory. We obtain the steady state of the system and found that the force contains three terms associated with the gradient force, the back-action force resulting from the intra-cavity photon energy change, as well as the reactive force associated with the coupling between the external field and the cavity. Moreover, we solve the dynamical system for a dielectric particle in a small mode volume cavity, which is characterized by a quasi-periodic pattern. These results are important for understanding the control of various types of levitated nano-particles through optomechanical coupling. [ABSTRACT FROM AUTHOR]

Magnetic hybrid hydrogels have exhibited remarkable efficacy in various areas, particularly in the biomedical sciences, where these inventive substances exhibit intriguing prospects for controlled drug delivery, tissue engineering, magnetic separation, MRI contrast agents, hyperthermia, and thermal ablation. Additionally, droplet-based microfluidic technology enables the fabrication of microgels possessing monodisperse characteristics and controlled morphological shapes. Here, alginate microgels containing citrated magnetic nanoparticles (MNPs) were produced by a microfluidic flow-focusing system. Superparamagnetic magnetite nanoparticles with an average size of 29.1 ± 2.5 nm and saturation magnetization of 66.92 emu/g were synthesized via the co-precipitation method. The hydrodynamic size of MNPs was changed from 142 nm to 826.7 nm after the citrate group's attachment led to an increase in dispersion and the stability of the aqueous phase. A microfluidic flow-focusing chip was designed, and the mold was 3D printed by stereo lithographic technology. Depending on inlet fluid rates, monodisperse and polydisperse microgels in the range of 20–120 μm were produced. Different conditions of droplet generation in the microfluidic device (break-up) were discussed considering the model of rate-of-flow-controlled-breakup (squeezing). Practically, this study indicates guidelines for generating droplets with a predetermined size and polydispersity from liquids with well-defined macroscopic properties, utilizing a microfluidic flow-focusing device (MFFD). Fourier transform infrared spectrometer (FT-IR) results indicated a chemical attachment of citrate groups on MNPs and the existence of MNPs in the hydrogels. Magnetic hydrogel proliferation assay after 72 h showed a better rate of cell growth in comparison to the control group (p = 0.042). [ABSTRACT FROM AUTHOR]

The aim of this study was to investigate the magnetic properties of mixed nanocrystalline Zn/manganese oxide compounds synthesized by a hydrothermal method. These compounds are designed as (ZnO)1−n(MnO)n, where index n ranges from 0.05 to 0.60. The results of magnetic measurements, including AC magnetic susceptibility as a function of temperature (up to 160 K) and frequency (from 7 Hz up to 9970 Hz), as well as DC magnetization in magnetic fields up to 9 T and temperature up to 50 K, are reported. We observed various types of magnetic behavior depending on the nominal weight content of MnO. Samples with a low nominal content (up to n = 0.10) of MnO exhibited Curie–Weiss behavior at higher temperatures. For samples with high nominal weight contribution (from n = 0.30 to 0.60), spin-glass-like or/and weak ferromagnetic behavior is observed. [ABSTRACT FROM AUTHOR]

The scattering phase function is crucial to analyze the light transport in the micron/nano particle suspensions. A new method including a liquid–particle system and reference system is proposed to measure the scattering phase function of the liquid–particle suspensions. In this method, a reference system of a standard particle is used to obtain the correction factor to compensate for the influence of the cuvette. Experimental validation was conducted for monodisperse silicon dioxide microspheres and monodisperse polystyrene microspheres. By considering the influence of the cuvette, both theoretical and experimental analyses prove that the proposed method can achieve a good result in the measurement of the scattering phase function of liquid–particle suspensions for particles with unknown size parameters and optical constants, especially when the size parameter of the particle is larger than 10. The correction factors of scattering light distribution of silicon dioxide microsphere suspensions with various mean particle sizes were obtained and analyzed. This method provides an alternative and simple way of measuring the scattering phase function of micron/nano particle suspensions. [ABSTRACT FROM AUTHOR]

Electromagnetic properties of cylindrical active coated nano-particles comprised of a silica nano-cylinder core layered with a plasmonic concentric nano-shell are investigated for potential nano-sensor applications. Particular attention is devoted to the near-field properties of these particles, as well as to their far-field radiation characteristics, in the presence of an electric or a magnetic line source. A constant frequency canonical gain model is used to account for the gain introduced in the dielectric part of the nano-particle, whereas three different plasmonic materials (silver, gold, and copper) are employed and compared for the nano-shell layers. [ABSTRACT FROM AUTHOR]

The synthesis of polymer brush decorated silica nano-particles is demonstrated by activator regeneration by electron transfer atom transfer radical polymerization (ARGET ATRP) grafting of poly(tert-butyl methacrylate). ATRP initiator decorated silica nano-particles were obtained using a novel trimethylsiloxane derivatised ATRP initiator obtained by click chemistry. Comparison of de-grafted polymers with polymer obtained from a sacrificial initiator demonstrated good agreement up to 55% monomer conversion. Subsequent mild deprotection of the tert-butyl ester groups using phosphoric acid yielded highly colloidal and pH stable hydrophilic nano-particles comprising approximately 50% methacrylic acid groups. The successful bio-conjugation was achieved by immobilization of Horseradish Peroxidase to the polymer brush decorated nano-particles and the enzyme activity demonstrated in a conversion of o-phenylene diamine dihydrochloride assay. [ABSTRACT FROM AUTHOR]

The effect produced by the application of methyl jasmonate (MeJA) in vineyards is clear, but this is a product that, despite its efficiency, is expensive, volatile and difficult to dissolve. Regarding increasing the MeJA use efficiency, new forms of application are proposed in this article, such as the use of calcium phosphate nanoparticles with two different morphologies: amorphous (ACP) and crystalline (Ap). In addition, few of the studies addressed so far have assessed MeJA's effect during the ripening period of the grapes. As a result of this, in this article, we evaluated/studied for first time the effect of the different MeJA formats on the phenolic composition of the grape during the ripening period. The results showed small differences between the two morphologies of the nanoparticles, which promoted a significant a delay in the sugar accumulation and an increase in the different phenolic compounds compared to the control. Such improvements were not as significant as those induced by the conventional MeJA treatment. However, it is remarkable that when the nanoparticles were applied, we used a concentration 10 times lower than when it is used conventionally. Therefore, these findings revealed that both types of calcium phosphate nanoparticles are potential MeJA nanocarriers allowing for the increase in the quality of the grapes at the time of harvest in a more sustainable way, although future studies must be carried out in order to optimise the concentration with which these nanoparticles are doped. [ABSTRACT FROM AUTHOR]

The use of biodegradable films to replace the synthetic polymers prepared from natural polymers has been strongly limited owing to their poor barrier and mechanical properties. The modification was carried out with a partial replacement of natural polymers with synthetic polymer, such as PVA (poly vinyl alcohol), to increase the barrier properties of the film. The addition of an active ingredient in the form of nanoparticles such as Zinc Oxide (ZnO), enhanced the properties of the packaging materials compared to the conventional composite film, to which sonication imparted an excellent dispersion of nanoparticles in the slurry. The film thickness, water vapor permeability, film solubility, and mechanical properties of the composite, the composite with PVA, and the composite with PVA and ZnO nanoparticle film (active film) values differed significantly (p < 0.05) between the samples. The Z-average diameters of the composite slurry, the composite with PVA slurry, and the composite with PVA and ZnO nanoparticle slurry ranged from 242.20 to 1021.03 in nanometers (d-nm). The PDI and zeta potential of the samples were also analyzed. The antibacterial activity of the nanoparticles showed a distinct inhibition against Gram-positive Bacillus cereus and Gram-negative Escherichia coli in the treated films counterpart to the control films. The active film conferred excellent mechanical and barrier properties, including antibacterial properties. [ABSTRACT FROM AUTHOR]

The formation of purely metallic meso-porous metal thin films by partial interface coalescence of self-assembled metal nano-particles across aqueous solutions of Pluronics triblock lyotropic liquid crystals is demonstrated for the first time. Small angle X-ray scattering was used to study the influence of the thin film composition and processing conditions on the ordered structures. The structural characteristics of the meso-structures formed demonstrated to primarily rely on the lyotropic liquid crystal properties while the nature of the metal nano-particles used as well as the their diameters were found to affect the ordered structure formation. The impact of the annealing temperature on the nano-particle coalescence and efficiency at removing the templating lyotropic liquid crystals was also analysed. It is demonstrated that the lyotropic liquid crystal is rendered slightly less thermally stable, upon mixing with metal nano-particles and that low annealing temperatures are sufficient to form purely metallic frameworks with average pore size distributions smaller than 500 nm and porosity around 45% with potential application in sensing, catalysis, nanoscale heat exchange, and molecular separation. [ABSTRACT FROM AUTHOR]

As the knowledge about the interferences of nanomaterials on human staminal cells are scarce and contradictory, we undertook a comparative multidisciplinary study based on the size effect of zero-valent iron, cobalt and nickel microparticles (MPs) and nanoparticles (NPs) using human adipose stem cells (hASCs) as a model and evaluating cytotoxicity, morphology, cellular uptake and gene expression. Our results suggested that the medium did not influence the cell sensitivity but, surprisingly, the iron microparticles (FeMPs) resulted in being toxic. These data were supported by modifications in mRNA expression of some genes implicated in the inflammatory response. Microscopic analysis confirmed that NPs, mainly internalized by endocytosis, persist in the vesicles without any apparent cell damage. Conversely, MPs are not internalized and the effects on hASCs have to be ascribed to the release of ions in the culture medium, or to the reduced oxygen and nutrient exchange efficiency due to the presence of MP agglomerating around the cells. Notwithstanding the results depicting a heterogeneous scene that does not allow drawing a general conclusion, this work reiterates the importance of comparative investigations on MPs, NPs and corresponding ions and the need to continue the thorough verification of NP and MP innocuousness to ensure unaffected stem cell physiology and differentiation. [ABSTRACT FROM AUTHOR]

The properties and photocatalytic performance of anatase nanoparticles of pure TiO2 and a core-shell structure of TiO2 on calcined vetiver grass leaves have been compared. Samples were fabricated by sol-gel and heating at 450 - °C for 5 h. The comparison was based on data for X-ray diffraction (XRD), UV-Vis spectrophotometry, photoluminescence, transmission electron microscopy, specific surface area measurement, pore volume assessment, and methylene blue degradation testing. The results showed that the pure TiO2 consisted of agglomerated equiaxed nanoparticles of individual grain sizes in the range 10-20 nm. In contrast, the TiO2-vetiver composite exhibited a core-shell structure consisting of a carbonaceous core and TiO2 shell of thickness 10-15 nm. These features influenced the photocatalytic performance in such a way that the lower cross-sectional area, greater surface area, and higher pore volume of the TiO2 shell increased the number of active sites, reduced the charge carrier diffusion distance, and reduced the recombination rate, thereby improving the photocatalytic activity. This improvement derived from morphological characteristics rather than crystallographic, semiconducting, or optical properties. The improved performance of the TiO2-vetiver core-shell was unexpected since the X-ray diffraction data showed that the crystallinity of the TiO2 was lower than that of the pure TiO2. These outcomes are attributed to the reducing effect of the carbon on the TiO2 during heating, thereby facilitating the formation of oxygen vacancies, which enhance charge separation and hence photocatalysis by TiO2. [ABSTRACT FROM AUTHOR]

It has been difficult to detach abrasive particles smaller than 50 nm from polished surfaces in post-CMP cleaning. During the cleaning process, the residual nano-particles exert shear force in the inevitable shear flow. In order to understand the cleaning mechanism, it is indispensable to investigate not only the force but also the energy acting on different-sized nano-particles. In this article, we proposed the evaluation of detachment energy (the energy required to detach nano-particles) by using Lateral Force Microscopy. As an example, the dominant detachment energy of the silica nano-particle between the oxide film is the potential energy of the hydrogen bond. It suggested that the silica nano-particle detachment involves the breaking of hydrogen bonds. [ABSTRACT FROM AUTHOR]

In Fe-Mn-Al-Ni shape memory alloys, the stabilization of superelasticity would be affected by the undesired precipitation of B2 nano-particles during natural aging. In order to solve this problem, the effect of Mo alloying on the precipitation behavior of B2 nano-particles during the cooling and natural aging processes was performed by scanning electron microscope, transmission electron microscope and Vickers microhardness test in two Fe-Mn-Al-Ni-Mo shape memory alloys. The results showed that the formation of γ phase was completely suppressed after 15 °C and 80 °C water quenching as well as air cooling. However, B2 nano-particles were still precipitated after the three cooling processes, and their sizes and misfits increased with decreasing the cooling rates. In addition, the Vickers hardness increased after natural aging for 338 days, which indicated that it is not viable to inhibit the precipitation of B2 nano-particles during natural aging by Mo alloying in the Fe-Mn-Al-Ni shape memory alloys. [ABSTRACT FROM AUTHOR]

A worldwide growing trend is dedicated towards reducing carbon dioxide emissions from mechanical systems in different industries. One key factor under focus of research is to decrease energy losses in rotating machinery during operation by improving lubrication performance. This paper presents a novel grease nano-additive using activated carbon (AC) as a byproduct from recycled polymer waste. Five different concentrations of AC nanoparticles (ACNPs) are added to lithium grease to obtain blends containing 0.025 wt.%, 0.05 wt.%, 0.1 wt.%, 0.5 wt.%, and 1 wt.%. The tribological assessment of blends has been performed using a four-ball wear test and load carrying capacity test. The obtained results for blends are compared to samples of base grease and to blends with 2 wt.% reduced graphene oxide (rGO). Test results showed a remarkable enhancement of load carrying capacity of AC samples by 20–30% as compared to base grease. By observing wear scar in rolling elements, the ACNPs lowered the average wear scar diameter (WSD) for all samples by 30–36%. Base grease samples showed the highest coefficient of friction (COF) values between 0.15 and 0.17. These values are reduced to 0.03 and 0.06 for grease with ACNPs reaching their minimum in the case of 1 wt.% AC. These outcomes are found consistent with the enhancements in driving power saving values. The results proved the competitiveness and suitability of the AC as a recycled waste and nano-additive for improving the tribological performance of grease lubrication. [ABSTRACT FROM AUTHOR]

In this work, a series of novel flower-like Ag@AgCl/Bi2O2CO3 were prepared by simple and feasible oil-in-water self-assembly processes. The phase structures of as-prepared samples were examined by X-ray diffraction (XRD), Scanning electron microscopy (SEM), Transmission electron microscopy (TEM), UV-vis diffuse reflectance spectroscopy (DRS), X-ray fluorescence spectrometer (XRF), etc. The characterization results indicated that the presence of Ag@AgCl did not affect the crystal structure, but exerted a great influence on the photocatalytic activity of Bi2O2CO3 and enhanced the absorption band of pure Bi2O2CO3. The photocatalytic activities of the Ag@AgCl/Bi2O2CO3 samples were determined by photocatalytic degradation of methylene blue (MB) under visible light irradiation. The Ag@AgCl (10 wt %)/Bi2O2CO3 composite showed the highest photocatalytic activity, degrading 97.9% MB after irradiation for 20 min, which is over 1.64 and 3.66 times faster than that of pure Ag@AgCl (calculated based on the equivalent Ag@AgCl content in Ag@AgCl (10 wt %)/Bi2O2CO3) and pure Bi2O2CO3, respectively. Bisphenol A (BPA) was also degraded to further prove the degradation ability of Ag@AgCl/Bi2O2CO3. Photocurrent studies indicated that the recombination of photo-generated electron-hole pairs was decreased effectively due to the formation of heterojunctions between flower-like Bi2O2CO3 and Ag@AgCl nanoparticles. Trapping experiments indicated that O2-, h+ and Cl° acted as the main reactive species for MB degradation in the present photocatalytic system. Furthermore, the cycling experiments revealed the good stability of Ag@AgCl/Bi2O2CO3 composites. Based on the above, a photocatalytic mechanism for the degradation of organic compounds over Ag@AgCl/Bi2O2CO3 was proposed. [ABSTRACT FROM AUTHOR]

Nano-technology has played a vital role in upgrading the durability and sustainability of asphalt pavements during the last decade. Conventional bitumen does not provide adequate performance against permanent deformation in severe weather conditions. Quartz nano-size particles (QNPs) (1, 3, and 5% by weight of the bitumen) were employed in this research to modify the conventional base bitumen PG 58–16. Conventional physical (penetration, softening, ductility, and flash and fire point), rheological, frequency sweep, high-performance grading, and moisture susceptibility tests were performed to investigate the enhancement of the base bitumen performance. Marshall mix design was conducted on each asphalt mixture to determine the optimum bitumen content (OBC) percentage for the preparation of wheel tracker samples to evaluate the effect of QNPs on asphalt mixtures. Laboratory test findings showed that the optimum concentration of QNPs is 5% by weight of base bitumen. The homogeneity and proper stable dispersion of QNPs in the bitumen were validated via scanning electron microscope (SEM), Fourier transform infrared spectroscopy (FTIR), and storage stability tests. At higher temperatures, the QNP-modified asphalt mixtures exhibited higher stiffness, stripping resistance, and rutting potential. It was concluded that QNPs effectively upgrade durability and permanent deformation resistance at high temperatures and, therefore, the sustainability of asphalt roads. [ABSTRACT FROM AUTHOR]

In recent decades, considerable efforts have been made in the production of steel and the modification of its microstructure on the nano-scale in order to improve its mechanical properties. One possibility is through nano-particles incorporation and reinforcement. While typical production methods for Metal Matrix nano-Composites (MMnCs) are difficult and expensive, the main drawback of the casting method is the agglomeration of the nano-particles and a poor interface between the nano-particles and the metal matrix. Therefore, the aim of this study was to investigate the potential of adding nano-particles as reinforcement elements through the conventional liquid-metal casting process. The investigation was focused on the various approaches to the modification and addition of nano-particles in the melt, as well as the influence of particle concentration and size on their homogeneity and distribution within the steel matrix. The results show that also in the case of the conventional casting process, it is possible to produce a reinforced steel-matrix nano-composite with a homogeneous distribution of the Al2O3 nano-particles in the matrix. However, in order to obtain a homogeneous distribution of nano-particles in the steel matrix, a dispersion agent is required. [ABSTRACT FROM AUTHOR]

Nano-hydroxyapatite (n-HA) is the main inorganic component of natural bone, which has been widely used as a reinforcing filler for polymers in bone materials, and it can promote cell adhesion, proliferation, and differentiation. It can also produce interactions between cells and material surfaces through selective protein adsorption and has therefore always been a research hotspot in orthopedic materials. However, n-HA nano-particles are inherently easy to agglomerate and difficult to disperse evenly in the polymer. In addition, there are differences in trace elements between n-HA nano-particles and biological apatite, so the biological activity needs to be improved, and the slow degradation in vivo, which has seriously hindered the application of n-HA in bone fields, is unacceptable. Therefore, the modification of n-HA has been extensively reported in the literature. This article reviewed the physical modification and various chemical modification methods of n-HA in recent years, as well as their modification effects. In particular, various chemical modification methods and their modification effects were reviewed in detail. Finally, a summary and suggestions for the modification of n-HA were proposed, which would provide significant reference for achieving high-performance n-HA in biomedical applications. [ABSTRACT FROM AUTHOR]

Intra-cellular active transport by native cargos is ubiquitous. We investigate the motion of spherical nano-particles (NPs) grafted with flexible polymers that end with a nuclear localization signal peptide. This peptide allows the recruitment of several mammalian dynein motors from cytoplasmic extracts. To determine how motor–motor interactions influenced motility on the single microtubule level, we conducted bead-motility assays incorporating surface adsorbed microtubules and combined them with model simulations that were based on the properties of a single dynein. The experimental and simulation results revealed long time trajectories: when the number of NP-ligated motors Nm increased, run-times and run-lengths were enhanced and mean velocities were somewhat decreased. Moreover, the dependence of the velocity on run-time followed a universal curve, regardless of the system composition. Model simulations also demonstrated left- and right-handed helical motion and revealed self-regulation of the number of microtubule-bound, actively transporting dynein motors. This number was stochastic along trajectories and was distributed mainly between one, two, and three motors, regardless of Nm. We propose that this self-regulation allows our synthetic NPs to achieve persistent motion that is associated with major helicity. Such a helical motion might affect obstacle bypassing, which can influence active transport efficiency when facing the crowded environment of the cell. [ABSTRACT FROM AUTHOR]

The main reason for the limited usage of biodiesel is it tends to oxidize when exposed to air. It is anticipated that the addition of an antioxidant along with graphene nano particle improves combustion of diesel-biodiesel blend. In the present research biodiesel made from the transesterification of waste cooking oil is used. Three synthetic antioxidants butylated hydroxytoluene (BHT), 2(3)-t-butyl-4-hydroxyanisole (BHA) and tert butylhydroquinone (TBHQ) along with 30 ppm of graphene nano particle were added at a volume fraction of 1000 ppm to diesel–biodiesel blends (B20). The performance and emission tests were performed at constant engine speed of 1500 rpm. Because of the inclusion of graphene nano particles, surface area to the volume ratio of the fuel is augmented enhancing the mixing ability and chemical responsiveness of the fuel during burning causing superior performance, combustion and emission aspects of compression ignition engine. The results revealed that there was a slight increase in brake power and brake thermal efficiency of about 0.29%, 0.585%, 0.58% and 6.22%, 3.11%, 3.31% for B20GrBHT1000, B20GrBHA1000 and B20GrTBHQ1000, respectively, compared to B20. Additionally, BSFC, HC and NOx emissions were reduced to considerable levels for the reformed fuel. [ABSTRACT FROM AUTHOR]

A simple and economical biorefinery method, organosolv methyl isobutyl ketone (MIBK) pretreatment assisted by Lewis acid ferric trichloride hydrolysis, was proposed for fractionating the lignin from extractive-free Eucalyptus powder at the nanoscale, accompanied by another product furfural, derived from hemicellulose. Under the conditions (180 °C, 1 h) optimized based on the best yield of furfural, 40.13% of the acid-insoluble lignin (AIL) could be obtained with a high purity of 100%, a low molecular weight of 767 (Mn) and improved thermostability. The extracted lignin was characterized by its chemical structure, thermostability, homogeneity, molecular weight, and morphology as compared with milled wood lignin (MWL). The results showed significant variations in chemical structures of the extracted lignin during the pretreatment. Specifically, the aryl ether linkage and phenylcoumarans were broken severely while the resinols were more resistant. The G-type lignin was more sensitive to degradation than the S-type, and after the pretreatment, H-type lignin was formed, indicating the occurrence of a demethoxylation reaction at high temperature. Moreover, the lignin nano-particles were identified visually by AFM and TEM images. The dynamic light scattering (DLS) showed that the average diameter of the measured samples was 131.8 nm, with the polydispersity index (PDI) of 0.149. The MIBK-lignin nano-particles prepared in our laboratory exhibit high potentials in producing high functional and valuable materials for the application in wide fields. [ABSTRACT FROM AUTHOR]

We investigate the effect of intra-molecular cross-links on the properties of polymer bulks. To do this, we apply a combination of thermal, rheological, diffraction, and neutron spin echo experiments covering the inter-molecular as well as the intermediate length scales to melts of single-chain nano-particles (SCNPs) obtained through 'click' chemistry. The comparison with the results obtained in a bulk of the corresponding linear precursor chains (prior to intra-molecular reaction) and in a bulk of SCNPs obtained through azide photodecomposition process shows that internal cross-links do not influence the average inter-molecular distances in the melt, but have a profound impact at intermediate length scales. This manifests in the structure, through the emergence of heterogeneities at nanometric scale, and also in the dynamics, leading to a more complex relaxation behavior including processes that allow relaxation of the internal domains. The influence of the nature of the internal bonds is reflected in the structural relaxation that is slowed down if bulky cross-linking agents are used. We also found that any residual amount of cross-links is critical for the rheological behavior, which can vary from an almost entanglement-free polymer bulk to a gel. The presence of such inter-molecular cross-links additionally hinders the decay of density fluctuations at intermediate length scales. [ABSTRACT FROM AUTHOR]

A disposable organophosphorus pesticides (OPs) enzyme biosensor based on magnetic composite nanoparticle-modified screen printed carbon electrodes (SPCE) has been developed. Firstly, an acetylcholinesterase (AChE)-coated Fe3O4/Au (GMP) magnetic nanoparticulate (GMP-AChE) was synthesized. Then, GMP-AChE was absorbed on the surface of a SPCE modified by carbon nanotubes (CNTs)/nano-ZrO2/prussian blue (PB)/Nafion (Nf) composite membrane by an external magnetic field. Thus, the biosensor (SPCE∣CNTs/ZrO2/PB/Nf∣GMP-AChE) for OPs was fabricated. The surface of the biosensor was characterized by scanning electron micrography (SEM) and X-ray fluorescence spectrometery (XRFS) and its electrochemical properties were studied by cyclic voltammetry (CV) and differential pulse voltammetry (DPV). The degree of inhibition (A%) of the AChE by OPs was determined by measuring the reduction current of the PB generated by the AChE-catalyzed hydrolysis of acetylthiocholine (ATCh). In pH = 7.5 KNO3 solution, the A was related linearly to the concentration of dimethoate in the range from 1.0 × 10-3-10 ng·mL-1 with a detection limit of 5.6 × 10-4 ng·mL-1. The recovery rates in Chinese cabbage exhibited a range of 88%-105%. The results were consistent with the standard gas chromatography (GC) method. Compared with other enzyme biosensors the proposed biosensor exhibited high sensitivity, good selectivity with disposable, low consumption of sample. In particular its surface can be easily renewed by removal of the magnet. The convenient, fast and sensitive voltammetric measurement opens new opportunities for OPs analysis. [ABSTRACT FROM AUTHOR]

Bioactive glasses (BGs) are being increasingly considered for numerous biomedical applications. The loading of natural compounds onto BGs to increase the BG biological activity is receiving increasing attention. However, achieving efficient loading of phytotherapeutic compounds onto the surface of bioactive glass is challenging. The present work aimed to prepare novel amino-functionalized mesoporous bioactive glass nanoparticles (MBGNs) loaded with the phytotherapeutic agent Boswellia sacra extract. The prepared amino-functionalized MBGNs showed suitable loading capacity and releasing time. MBGNs (nominal composition: 58 wt% SiO2, 37 wt% CaO, 5 wt% P2O5) were prepared by sol-gel-modified co-precipitation method and were successfully surface-modified by using 3-aminopropyltriethoxysilane (APTES). In order to evaluate MBGNs loaded with Boswellia sacra, morphological analysis, biological studies, physico-chemical and release studies were performed. The successful functionalization and loading of the natural compound were confirmed with FTIR, zeta-potential measurements and UV-Vis spectroscopy, respectively. Structural and morphological evaluation of MBGNs was done by XRD, SEM and BET analyses, whereas the chemical analysis of the plant extract was done using GC/MS technique. The functionalized MBGNs showed high loading capacity as compared to non-functionalized MBGNs. The release studies revealed that Boswellia sacra molecules were released via controlled diffusion and led to antibacterial effects against S. aureus (Gram-positive) bacteria. Results of cell culture studies using human osteoblastic-like cells (MG-63) indicated better cell viability of the Boswellia sacra-loaded MBGNs as compared to the unloaded MBGNs. Therefore, the strategy of combining the properties of MBGNs with the therapeutic effects of Boswellia sacra represents a novel, convenient step towards the development of phytotherapeutic-loaded antibacterial, inorganic materials to improve tissue healing and regeneration. [ABSTRACT FROM AUTHOR]

We demonstrate high-performance InGaN/GaN blue light emitting diodes (LEDs) embedded with an air-void layer produced by a dry-etch of nano-pillars in an n-GaN layer grown on patterned sapphire substrate (PSS), filling the space between nano-pillars with SiO2 nano-particles (NPs) and subsequent epitaxial overgrowth. The structure exhibits enhanced output power compared to similarly grown reference conventional LED without the air-void layer. This change in growth procedure contributes to the increase of internal quantum efficiency (IQE) and light extraction efficiency (LEE) resulting in a 13.5% increase of light output. LEE is 2 times more affected than IQE in the modified structure. Simulation demonstrates that the main effect causing the LEE changes is due to the emitted light being confined within the upper space above the air-void layer and thus enhancing the light scattering by the SiO2 NPs and preferential light via front surface. [ABSTRACT FROM AUTHOR]

Lubricant additive plays an important role in reducing the friction and wear for base oil. MAX phase ceramics may have superior advantages for additive application due to their unique nanolayered structure. In this paper, Ti2SnC ceramic is prepared by sintering the elemental mixtures at 1250 °C. In addition, Cu-coated Ti2SnC ceramic is successfully prepared using a chemical plating method for the first time. It is confirmed that the Ti2SnC ceramic has good self-catalytic activity, and a layer of stacking Cu nano-particles can be deposited on the Ti2SnC surface without pretreatment. When the Cu-coated Ti2SnC ceramic powder is doped into PAO10 base oil, the oil can exhibit excellent lubrication properties, where the friction coefficient is as low as 0.095. A layer of tribo-film can be formed during the sliding process when the Cu-coated Ti2SnC ceramic is incorporated into PAO10 base oil, which can reduce the friction coefficient. The superior lubrication properties can be attributed to the synergistic lubrication effect of Ti2SnC ceramic and Cu nano-particles. [ABSTRACT FROM AUTHOR]

The influence of as-cast grain size on recrystallization and the related mechanical properties of Al–Zn–Mg–Cu-based alloys was investigated. Grain sizes ranging from 163 to 26 μm were achieved by adding Ti, Cr and Mn, and ZnO nano-particles, which acted as heterogeneous nucleation sites. A decrease in the as-cast grain size led to a corresponding reduction in the recrystallized grain size from 54 to 13 μm. Notably, as-cast grain sizes below 100 μm provided additional nucleation sites at grain boundaries, allowing for a reasonable prediction of recrystallized grain size. Finer grains also contributed to enhanced mechanical properties, with yield strength increasing as recrystallized grain size decreased without significant loss of elongation. Additional strengthening was observed due to η-precipitates at grain boundaries, further improving the properties of fine-grained sheets. [ABSTRACT FROM AUTHOR]

We studied the variation in electrical conductivity of exfoliated RuO2 nanosheets and the modulation in the contact resistance of individual nanosheet devices using charge transfer doping effects based on surface metal nanoparticle decorations. The electrical conductivity in the monolayer and bilayer RuO2 nanosheets gradually increased due to the surface decoration of Cu, and subsequently Ag, nanoparticles. We obtained contact resistances between the nanosheet and electrodes using the four-point and two-point probe techniques. Moreover, the contact resistances decreased during the surface decoration processes. We established that the surface decoration of metal nanoparticles is a suitable method for external contact engineering and the modulation of the internal properties of nanomaterials. [ABSTRACT FROM AUTHOR]