Search

In order to study the behavior of molten blast furnace slag ligament breakup into droplets by centrifugal granulation with a spinning cup, three-dimensional transient CFD model simulations were performed in the present work to study the process of the slag deformation into ligaments upon leaving the spinning cup, which eventually disintegrate into droplets. The formation of molten slag ligaments at the edge of the spinning cup and their disintegration into droplets were numerically revealed so that the behavior and mechanism of the slag ligament breakup into droplets could be investigated. This work specifically examined the influence of cup spinning speed on the diameter and length of the molten slag ligaments around the cup periphery and the diameter of the droplets produced. The simulation results show that, for the same slag flowrate, with the increase in cup spinning speed, the slag film thickness at the cup edge decreases, the number of molten slag ligaments increases, and the diameter of the ligaments decreases, thus reducing the diameter of slag droplets. Moreover, as the number of molten slag ligaments increases as a result of the increased cup spinning speed, the flowrate of a single ligament decreases, so that the ligament disintegrates in a shorter radial distance, that is, the length of the ligament is shortened. In addition, this work also investigated the behavior and mechanism of a single molten slag ligament breakup into droplets. It was found that the process of molten slag ligament breakup into droplets under the action of centrifugal force and surface tension can also be approximately explained by the theory of the Rayleigh disintegration mechanism. [ABSTRACT FROM AUTHOR]

Aiming at the mode of liquid ligament disintegration into droplets in the process of the centrifugal granulation of molten blast furnace slag using a spinning cup, in order to gain an in-depth understanding of the behavior and mechanism of droplet formation by liquid ligament disintegration and to obtain appropriate conditions to control the size of the produced slag granules, a three-dimensional CFD model describing water–air two-phase flow with a free surface was established in this work for simulating the process of a single water ligament breakup into droplets under the action of gravity, surface tension and inertial forces, so as to compare with the process of a molten slag ligament disintegration into droplets due to centrifugal force exerted by the spinning cup. By studying the disintegration behavior and mechanism of a single water ligament, the similar phenomenon of a molten slag ligament disintegration is examined. The numerical simulation results on the breakup of a single water ligament show that the length of the ligament before its disintegration and the diameter of the droplets formed both increase with the increase of the velocity of the ligament initially exiting a capillary nozzle. In addition, an experimental set-up was established in the laboratory to conduct cold physical model simulation experiments on single water or liquid paraffin ligament disintegration. The experimental results are compared with the numerical simulation results so that the reliability of the CFD model is verified. The results of the present study show that, in the centrifugal granulation process of blast furnace slag using a spinning cup operated in the ligament disintegration mode, the breakup of a single molten slag ligament is very similar to that of a single water or liquid paraffin ligament, and both approximately follow the Rayleigh Disintegration Mechanism, which provides a theoretical basis for analyzing the breakup process of the ligaments of different liquids as references for guiding the operation of centrifugal granulation of molten slag. [ABSTRACT FROM AUTHOR]

Bath smelting technologies based on top submerged lance (TSL) injection have been widely used for pyrometallurgical metal production and solid waste treatment. In this work, a two-dimensional CFD simulation model of a pilot-scale 300 kg TSL furnace was established and applied to investigate the slag splashing phenomenon caused by submerged gas injection and combustion, with a special focus on the effect of submerged combustion on bubble formation, splash generation, splash distribution and heat transfer in the top space of the TSL furnace. The slag splash amount and distribution, and the temperature distribution characteristics inside the TSL furnace, especially under the influence of submerged combustion, were predicted, and influences of lance immersion depth and total injection gas flowrate on the splash behavior and heat transfer were investigated. As the lance immersion depth increases, more splashes are generated that distribute more evenly in the furnace top space and consequently heat transfer is enhanced. A larger injection gas flowrate generally increases the splash amount but the effect becomes weak when the injection gas flowrate exceeds a certain level, and there exists an appropriate range in injection gas flowrate for achieving the best heat transfer efficiency in TSL furnace. [ABSTRACT FROM AUTHOR]