Search

Honeycomb structures made of carbon-fiber-reinforced plastic (CFRP) are increasingly used in the aerospace field due to their excellent energy absorption capability. Attention has been paid to CFRP structures in order to accurately simulate their progressive failure behavior and discuss their ply designability. In this study, the preparation process of a CFRP corrugated sheet (half of the honeycomb structure) and a CFRP honeycomb structure was illustrated. The developed finite element method was verified by a quasi-static test, which was then used to predict the low-velocity impact (LVI) behavior of the CFRP honeycomb, and ultimately, the influence of the ply angle and number on energy absorption was discussed. The results show that the developed finite element method (including the user-defined material subroutine VUMAT) can reproduce the progressive failure behavior of the CFRP corrugated sheet under quasi-static compression and also estimate the LVI behavior. The angle and number of plies of the honeycomb structure have an obvious influence on their energy absorption under LVI. Among them, energy absorption increases with the ply number, but the specific energy absorption is basically constant. The velocity drop ratios for the five different ply angles are 79.12%, 68.49%, 66.88%, 66.86%, and 60.02%, respectively. Therefore, the honeycomb structure with [0/90]s ply angle had the best energy absorption effect. The model proposed in this paper has the potential to significantly reduce experimental expenses, while the research findings can provide valuable technical support for design optimization in aerospace vehicle structures. [ABSTRACT FROM AUTHOR]

The inserts supporting run-flat tire (ISRFT) is mainly used in military off-road vehicles, which need to maintain high mobility after a blowout. Regulations show that the ISRFT can be driven safely for at least 100 km at a speed of 30 km/h to 40 km/h under zero-pressure conditions. However, the ISRFT generates serious heat during zero-pressure driving, which accelerates the aging of the tire rubber and degrades its performance. In order to study the thermo-mechanical coupling characteristics of the ISRFT, a three-dimensional finite element model verified by bench tests was established. Then, the stress–strain, energy loss and heat generation of the ISRFT were analyzed by the sequential thermo-mechanical coupling method to obtain the steady-state temperature field (SSTF). Finally, four kinds of honeycomb inserts bodies were designed based on the tangent method, and the SSTF of the honeycomb and the original ISRFT were compared. The results indicated that the high-temperature region of the ISRFT is concentrated in the shoulder area. For every 1 km/h increase in velocity, the temperature at the shoulder of the tire increases by approximately 1.6 °C. The SSTF of the honeycomb ISRFT is more uniformly distributed, and the maximum temperature of the shoulder decreases by about 30 °C, but the maximum temperature of the tread increases by about 40 °C. This study provides methodological guidance for investigating the temperature and mechanical characteristics of the ISRFT under zero-pressure conditions. [ABSTRACT FROM AUTHOR]

Due to their superior structural and mechanical properties, materials with negative Poisson's ratio are of increasing interest to research scholars, especially in fuel-efficient vehicles. In this work, a new concave I-shaped honeycomb structure is established by integrating the re-entrant hexagon and the I-shaped beam structure, and its negative Poisson's ratio characteristics and energy absorption properties are investigated. The effect of structural parameters on the energy absorption characteristics is analyzed using the finite element model. The results show that both the specific energy absorption and peak impact force decrease with the increase in cellular length and vertical short cellular height, and increase with the increase in horizontal short cellular length and cellular thickness. To obtain a smaller peak impact force and larger specific energy absorption with smaller mass, the four cell sizes were optimized by using Latin hypercube sampling, Gaussian radial basis function, and non-dominated sorting genetic algorithm II (NSGA-II). Compared with the original design, the SEA increased by 44.175%, and the PCF increased by 25.857%. Meanwhile, the mass decreased by 31.140%. Hence, the optimal structure has better crashworthiness. [ABSTRACT FROM AUTHOR]

In order to avoid the stress shielding phenomenon in orthopedic bionic bone implantation, it is necessary to consider the design of mechanical compatible implants imitating the host bone. In this study, we developed a novel cancellous bone structure design method aimed at ensuring the mechanical compatibility between the bionic bone and human bone by means of computer-aided design (CAD) and finite element analysis technology (specifically, finite element modeling (FEM)). An orthogonal lattice model with volume porosity between 59% and 96% was developed by means of CAD. The effective equivalent elastic modulus of a honeycomb structure with square holes was studied by FEM simulation. With the purpose of verifying the validity of the cancellous bone structure design method, the honeycomb structure was fabricated by selective laser sintering (SLS) and the actual equivalent elastic modulus of the honeycomb structure was measured with a uniaxial compression test. The experimental results were compared with the FEM values and the predicted values. The results showed that the stiffness values of the designed structures were within the acceptable range of human cancellous bone of 50–500 MPa, which was similar to the stiffness values of human vertebrae L1 and L5. From the point of view of mechanical strength, the established cellular model can effectively match the elastic modulus of human vertebrae cancellous bone. The functional relationship between the volume porosity of the nylon square-pore honeycomb structure ranging from 59% to 96% and the effective elastic modulus was established. The effect of structural changes related to the manufacture of honeycomb structures on the equivalent elastic modulus of honeycomb structures was studied quantitatively by finite element modeling. [ABSTRACT FROM AUTHOR]