Search

Cellulosic fibers obtained from Barley straw were utilized to reinforce PHB. Four different processed fibers were employed as reinforcing material: sawdust (SW), defibered (DFBF), delignified (DBF), and bleached (BBF) fibers. The composite was processed from two different perspectives: a discontinuous (bach) and an intensification process (extrusion). Once processed and transformed into final shape specimens, the materials were characterized by mechanical testing (tensile mode), scanning electron microscopy, and theoretical simulations by finite elements analysis (FEA). In terms of mechanical properties, only the elastic moduli (Et) exhibited results ranging from 37% to 170%, depending on the reinforcement composition. Conversely, strengths at break, under both tensile and bending tests, tended to decrease, indicating poor affinity between the components. Due to the mechanical treatment applied on the fiber, DFBF emerged as the most promising filler, with mechanical properties closest to those of neat PHB. DFBF-based composites were subsequently produced through process intensification using a twin-screw extruder, and molded into flowerpots. Mechanical results showed almost identical properties between the discontinuous and intensification processes. The suitability of the material for agriculture flowerpots was demonstrated through finite analysis simulation (FEA), which revealed that the maximum von Mises stresses (5.38 × 105 N/m2) and deformations (0.048 mm) were well below the limits of the composite materials. [ABSTRACT FROM AUTHOR]

The present investigation seeks to assess the impact of fillers on the mechanical characteristics of entirely biodegradable composites, introducing an advanced solution to fulfil long-term durability demands within point-of-purchase (POP) industries. The inclusion of calcium carbonate (CaCO3) fillers on the various properties of the flax fibre-reinforced composites, after accelerated irradiation in an ultraviolet (UV) radiation exposure has been investigated in the present study. Different types of flax fibre-reinforced poly lactic acid (PLA) biocomposites (with and without filler) were fabricated. The mechanical (tensile and flexural), and physical properties of the specimens were assessed after 500 h of exposure to accelerated UV irradiation of 0.48 W/m2 at 50 °C and were compared with those of the unexposed specimens. The results indicate that the presence of the inorganic filler significantly improved the performance of the biocomposites compared to the unfilled biocomposites after UV exposure. After adding 20% of fillers, the tensile strength was increased by 2% after UV degradation, whereas the biocomposite without filler lost 18% of its strength after UV exposure. This can be attributed to the change in the photo-degradation of the PLA due to the presence of the CaCO3 filler, which acts as a safeguard against UV light penetration by creating a protective barrier. The scanning electron microscopy (SEM) images of the degraded specimen surface show substantial difference in the surface topography of the composites with and without fillers. [ABSTRACT FROM AUTHOR]

This research work investigates the effects of the concentration and treatment of chopped false banana (Ensete ventricosum) fibres on the mechanical properties of a polypropylene matrix. The chopped false banana fibres (FBFs) were modified using Aloe Vera gel following treatment with 5% NaOH for 12 h at room temperature, with 1% acetic acid used to neutralise the remaining NaOH. FBF-reinforced polypropylene composite plates were then manufactured with 10, 20, 30, and 40 wt.% of chopped FBF. The mechanical properties were investigated using the compressive, impact, and three-point bending tests. Regarding the mechanical properties of the FBF-reinforced polypropylene composites, it was found that they have a maximum average compressive strength of 17.2 MPa. A maximum bending strength of 12.109 MPa was found for the Aloe Vera gel-treated composite with 30 wt.% of FBF. The maximum average compressive strength for this composite was 17.19 MPa. A maximum bending strength of 9.97 MPa for untreated composites was recorded for the composite with 10 wt.% of FBF. Finally, Aloe Vera-treated FBF-reinforced composites have better mechanical properties than untreated ones. The mechanical properties of Aloe Vera-treated FBF-reinforced polypropylene composites, as determined via impact, compressive and flexural tests, were superior for composites with 30 wt.% of FBF. [ABSTRACT FROM AUTHOR]

Paunch is a fibrous solid residue consisting of partially digested feed from the stomachs of processed cattle. It is the largest untapped solid waste stream from animals at meat processing plants, and potentially a valuable source of fibres for the production of sustainable and potentially higher-value natural biocomposite materials. Paunch was obtained from the waste effluent of a red meat processing plant, and the fibre characteristics of the as-obtained material were studied and benchmarked against wood flour and ground buffel grass, with a view to evaluating the potential of paunch as a fibre for polymer composites. The ground paunch possessed a rough fibrous surface and fibre-like characteristics that were comparable to both wood flour and ground buffel grass, demonstrating their potential for use in composites. Without any pre-treatment or compatibilisation, composites of a representative biopolymer, poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) and ground paunch were successfully produced for the first time via extrusion, with up to 50 wt% paunch content. Mechanical property analysis showed that, at 30 wt% content, PHBV/ground paunch composites yielded mechanical properties that were comparable to those of composites with ground buffel grass. [ABSTRACT FROM AUTHOR]

Natural fibers such as jute, cotton, and bamboo composites are becoming alternative materials to synthetic fiber composites, as their use raises awareness of environmental protection. Among natural fibers, jute and cotton fibers were used in this research to fabricate six-layered composites reinforced by spent tea leaves. Varying amounts (0, 5, 10, and 15 g) of spent tea leaf powder were incorporated as reinforcement with resin to improve and observe properties and determine usability. The prepared composites were investigated comparatively in terms of mechanical, microstructural, morphological, and thermal properties. As regards mechanical characterization, tensile, compression, and bending properties were tested in this research to compare the obtained data with the data available in the literature to show its practical application. The results indicated that significant improvements in mechanical properties were obtained from the composites up to a certain proportion of reinforcement. The addition of 10 g reinforcement of spent tea leaves improved tensile strength by 33.46% and compressive strength by 38.86%. In terms of microstructural, morphological, and thermal characterization, in-depth SEM, EDS, XRD, UV, FTIR, TGA, and DSC analyses were performed. The results revealed that advanced microstructural, morphological, and thermal properties were improved with a certain proportion of spent tea leaf reinforcement. [ABSTRACT FROM AUTHOR]

Low-porosity materials based on hot-pressed wood fibers or nanocellulose fibrils (no polymer matrix) represent a new concept for eco-friendly materials with interesting mechanical properties. For the replacement of fossil-based materials, physical properties of wood fiber materials need to be improved. In addition, the carbon footprint and cumulative energy required to produce the material also needs to be reduced compared with fossil-based composites, e.g., glass fiber composites. Lignin-containing fibers and nanofibers are of high yield and special interest for development of more sustainable materials technologies. The present mini-review provides a short analysis of the potential. Different extraction routes of lignin-containing wood fibers are discussed, different processing methods, and the properties of resulting fiber materials. Comparisons are made with analogous lignin-containing nanofiber materials, where mechanical properties and eco-indicators are emphasized. Higher lignin content may promote eco-friendly attributes and improve interfiber or interfibril bonding in fiber materials, for improved mechanical performance. [ABSTRACT FROM AUTHOR]

In recent years the interest in the realization of green wood plastic composites (GWPC) materials has increased due to the necessity of reducing the proliferation of synthetic plastics. In this work, we study a specific class of GWPCs from its synthesis to the characterization of its mechanical properties. These properties are related to the underlying microstructure using both experimental and modeling approaches. Different contents of Miscanthus giganteus fibers, at 5, 10, 20, 30 weight percent's, were thus combined to a microbial matrix, namely poly (3-hydroxybutyrate)-co-poly(3-hydroxyvalerate) (PHBHV). The samples were manufactured by extrusion and injection molding processing. The obtained samples were then characterized by cyclic-tensile tests, pycnometer testing, differential scanning calorimetry, Fourier transform infrared spectroscopy, X-ray diffraction, and microscopy. The possible effect of the fabrication process on the fibers size is also checked. In parallel, the measured properties of the biocomposite were also estimated using a Mori–Tanaka approach to derive the effective behavior of the composite. As expected, the addition of reinforcement to the polymer matrix results in composites with higher Young moduli on the one hand, and lower failure strains and tensile strengths on the other hand (tensile modulus was increased by 100% and tensile strength decreased by 23% when reinforced with 30 wt % of Miscanthus fibers). [ABSTRACT FROM AUTHOR]

Over recent years, enthusiasm towards the manufacturing of biopolymers has attracted considerable attention due to the rising concern about depleting resources and worsening pollution. Among the biopolymers available in the world, polylactic acid (PLA) is one of the highest biopolymers produced globally and thus, making it suitable for product commercialisation. Therefore, the effectiveness of natural fibre reinforced PLA composite as an alternative material to substitute the non-renewable petroleum-based materials has been examined by researchers. The type of fibre used in fibre/matrix adhesion is very important because it influences the biocomposites' mechanical properties. Besides that, an outline of the present circumstance of natural fibre-reinforced PLA 3D printing, as well as its functions in 4D printing for applications of stimuli-responsive polymers were also discussed. This research paper aims to present the development and conducted studies on PLA-based natural fibre bio-composites over the last decade. This work reviews recent PLA-derived bio-composite research related to PLA synthesis and biodegradation, its properties, processes, challenges and prospects. [ABSTRACT FROM AUTHOR]

Chromium-tanned leathers used in the manufacture of footwear and leather goods pose an environmental problem because they contain harmful chemicals and are very difficult to recycle. A solution to this problem can be composite materials from tree leaves, fruit residues and other fibrous agricultural products, which can replace chromium-tanned leather. The present study describes the preparation of biocomposite leather-like materials from microbial cellulose and maple leave fibers as bio-fillers. The formulation was optimized by design of experiment and the prepared biocomposites characterized by tensile test, FTIR, DMA, SEM, adhesion test, volume porosity, water absorptivity, surface wettability and shape stability. From the viewpoint of future use in the footwear industry, results obtained showed that the optimized material was considerably flexible with tensile strength of 2.13 ± 0.29 MPa, elastic modulus of 76.93 ± 1.63 MPa and porosity of 1570 ± 146 mL/min. In addition, the material depicted good shape stability and surface adhesive properties. The results indicate that a suitable treatment of biomass offers a way to prepare exploitable nonwoven fibrous composites for the footwear industry without further burdening the environment. [ABSTRACT FROM AUTHOR]

In this work, the effects of chemical pretreatment and different fiber loadings on mechanical properties of the composites at the sub-micron scale were studied through nanoindentation. The composites were prepared by incorporating choline chloride (ChCl) pretreated rice husk waste (RHW) in low-density polyethylene (LDPE) using melt processing, followed by a thermal press technique. Nanoindentation experiments with quasi continuous stiffness mode (QCSM) were performed on the surface of produced composites with varying content of pretreated RHW (i.e., 10, 15, and 20 wt.%). Elastic modulus, hardness, and creep properties of fabricated composites were measured as a function of contact depth. The results confirmed the appreciable changes in hardness, elastic modulus, and creep rate of the composites. Compliance curves indicated that the composite having 20 wt.% of pretreated RHW loading was harder compared to that of the pure LDPE and other composite samples. The values of elastic modulus and hardness of the composite containing 20 wt.% pretreated RHW were increased by 4.1% and 24% as compared to that of the pure LDPE, respectively. The creep rate of 42.65 nm/s and change in depth of 650.42 nm were also noted for the composite with RHW loading of 20 wt.%, which showed the substantial effect of holding time at an applied peak load of 100 mN. We believe that the developed composite could be a promising biodegradable packaging material due to its good tribo-mechanical performance. [ABSTRACT FROM AUTHOR]

Biocomposites can be both environmentally and economically beneficial: during their life cycle they generally use and generate less petroleum-based carbon, and when produced from the byproduct of another industry or recycled back to the manufacturing process, they will bring additional economic benefits through contributing to a circular economy. Here we investigate and compare the environmental performance of a biocomposite composed of a soybean oil-based resin (epoxidized sucrose soyate) and flax-based reinforcement using life cycle assessment (LCA) methodology. We evaluate the main environmental impacts that are generated during the production of the bio-based resin used in the biocomposite, as well as the biocomposite itself. We compare the life cycle impacts of the proposed biocomposite to a functionally similar petroleum-based resin and flax fiber reinforced composite, to identify tradeoffs between the environmental performance of the two products. We demonstrate that the bio-based resin (epoxidized sucrose soyate) compared to a conventional (bisphenol A-based) resin shows lower negative environmental impacts in most studied categories. When comparing the biocomposite to the fossil fuel derived composite, it is demonstrated that using epoxidized sucrose soyate versus a bisphenol A (BPA)-based epoxy resin can improve the environmental performance of the composite in most categories except eutrophication and ozone layer depletion. For future designs, considering an alternative cross-linker to facilitate the bond between the bio-based resin and the flax fiber, may help improve the overall environmental performance of the biocomposite. An uncertainty analysis was also performed to evaluate the effect of variation in LCA model inputs on the environmental results for both the biocomposite and composite. The findings show a better overall carbon footprint for the biocomposite compared to the BPA-based composite at almost all times, demonstrating a good potential for marketability especially in the presence of incentives or regulations that address reducing the carbon intensity of products. This analysis allowed us to pinpoint hotspots in the biocomposite's supply chain and recommend future modifications to improve the product's sustainability. [ABSTRACT FROM AUTHOR]

Today, plant fibers are considered as an important new renewable resource that can compete with some synthetic fibers, such as glass, in fiber-reinforced composites. In previous works, it was noted that the pectin-enriched middle lamella (ML) is a weak point in the fiber bundles for plant fiber-reinforced composites. ML is strongly bonded to the primary walls of the cells to form a complex layer called the compound middle lamella (CML). In a composite, cracks preferentially propagate along and through this layer when a mechanical loading is applied. In this work, middle lamellae of several plant fibers of different origin (flax, hemp, jute, kenaf, nettle, and date palm leaf sheath), among the most used for composite reinforcement, are investigated by atomic force microscopy (AFM). The peak-force quantitative nanomechanical property mapping (PF-QNM) mode is used in order to estimate the indentation modulus of this layer. AFM PF-QNM confirmed its potential and suitability to mechanically characterize and compare the stiffness of small areas at the micro and nanoscale level, such as plant cell walls and middle lamellae. Our results suggest that the mean indentation modulus of ML is in the range from 6 GPa (date palm leaf sheath) to 16 GPa (hemp), depending on the plant considered. Moreover, local cell-wall layer architectures were finely evidenced and described. [ABSTRACT FROM AUTHOR]

Natural fiber reinforced polymer-based composites have been growing into a type of green composites. The properties of natural fiber reinforced polymer-based composites are closely related to the structure of natural fibers. Bagasse fiber (BF) is one of the most used natural fibers for preparing natural fiber reinforced polymer-based composites. However, few examples of previous research touch on the quantitatively characterization of structure of BF and its effect on the properties of BF reinforced polymer-based composites. In this work, four kinds of BF including untreated BF (UBF), alkali treated BF (ABF), BF modified by silane coupling agent (SBF), and BF modified combining alkali treatment with silane coupling agent (ASBF) were prepared and melting blended with polylactic acid (PLA) to prepare PLA/BF composites. Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), thermogravimetry (TGA) and mechanical properties testing were used to characterize and analyze the structure and properties of modified BF and its reinforced PLA-based composites. Results showed that the used methods changed the structure of BF and their bonding modes. The surface energies of UBF, ABF, SBF, and ASBF were 19.8 mJ/m2, 34.7 mJ/m2, 12.3 mJ/m2, and 21.6 mJ/m2, respectively. The O/C ratios of UBF, ABF, SBF and, ASBF are 0.48, 0.53, 0.47, and 0.51. Due to the synergistic effect of alkali treatment and silane coupling agent modification on the surface chemical properties, the content of silicon elements on the surface of ASBF (4.15%) was higher than that of ASBF (2.38%). However, due to the destroying of alkali treatment on the microstructure of BF, the alkali treatment had no prominently synergetic effect with coupling agent modification on the mechanical properties of PLA/BF composites. Alkali treatment removed the small molecular compounds from BF, decreased its thermal stability, and increased the crystalline region and crystallinity of cellulose. Meanwhile, alkali treatment made BF fibrillated and increased its contactable active area with the coupling agents, but destructed the nature structure of BF. The silane coupling agent played a more important role than alkali treatment did in improving the interfacial compatibility of PLA/BF composites. [ABSTRACT FROM AUTHOR]

Fused deposition modeling (FDM) is a rapidly growing three-dimensional (3D) printing technology and has great potential in medicine. Polyether-ether-ketone (PEEK) is a biocompatible high-performance polymer, which is suitable to be used as an orthopedic/dental implant material. However, the mechanical properties and biocompatibility of FDM-printed PEEK and its composites are still not clear. In this study, FDM-printed pure PEEK and carbon fiber reinforced PEEK (CFR-PEEK) composite were successfully fabricated by FDM and characterized by mechanical tests. Moreover, the sample surfaces were modified with polishing and sandblasting methods to analyze the influence of surface roughness and topography on general biocompatibility (cytotoxicity) and cell adhesion. The results indicated that the printed CFR-PEEK samples had significantly higher general mechanical strengths than the printed pure PEEK (even though there was no statistical difference in compressive strength). Both PEEK and CFR-PEEK materials showed good biocompatibility with and without surface modification. Cell densities on the "as-printed" PEEK and the CFR-PEEK sample surfaces were significantly higher than on the corresponding polished and sandblasted samples. Therefore, the FDM-printed CFR-PEEK composite with proper mechanical strengths has potential as a biomaterial for bone grafting and tissue engineering applications. [ABSTRACT FROM AUTHOR]