Search

This study focuses on using activated fly ash to preparate silica aerogel by the acid solution–alkali leaching method and ambient pressure drying. Additionally, to improve the performance of silica aerogel, C6H16O3Si (KH-570) and CH3Si(CH3O)3 (MTMS) modifiers were used. Finally, this paper investigated the factors affecting the desilication rate of fly ash and analyzed the structure and performance of silica aerogel. The experimental results show that: (1) The factors affecting the desilication rate are ranked as follows: hydrochloric acid concentration > solid–liquid ratio > reaction temperature > reaction time. (2) KH-570 showed the best performance, and when the volume ratio of the silica solution to it was 10:1, the density of silica aerogel reached a minimum of 183 mg/cm3. (3) The optimal process conditions are a hydrochloric acid concentration of 20 wt%, a solid–liquid ratio of 1:4, a reaction time of two hours, and a reaction temperature of 100 °C. (4) The optimal performance parameters of silica aerogel were the thermal conductivity, specific surface area, pore volume, average pore size, and contact angle values, with 0.0421 W·(m·K)−1, 487.9 m2·g−1, 1.107 cm3·g−1, 9.075 nm, and 123°, respectively. This study not only achieves the high-value utilization of fly ash, but also facilitates the effective recovery and utilization of industrial waste. [ABSTRACT FROM AUTHOR]

The huge demand for sand and gravel resources in road engineering construction leads to excessive consumption of resources and environmental damage. Recycling waste concrete and industrial solid waste as a road material is a promising alternative. In order to explore the application of these solid wastes in the road base, this paper studies the effect of adding lithium slag activated by an alkaline activator, fly ash (FA) and a combination of the two on the compressive strength, splitting strength and shrinkage performance of recycled cement-stabilized macadam mixture (RCSM). The optimum content of recycled aggregate (RA), alkali-activated lithium slag (AALS) and FA in composite-improved RCSM was optimized using a response surface method (Box–Behnken), and the microscopic characteristics of the mixture were analyzed using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results show that the optimum dosage of AALS, FA and RA determined by the response surface method is 15%, 10% and 40%, respectively. Compared with the cement-stabilized macadam mixture (CSM) with 40% RA, the 28 d compressive strength and 28 d splitting strength of the composite-improved RCSM are increased by 26.8% and 22.9%, respectively, and the dry shrinkage coefficient and average temperature shrinkage coefficient are decreased by 25.8% and 14.8%, respectively. Microscopic tests show that AALS and FA participate in the hydration reaction, generate more hydrated silicate (C-S-H) and ettringite (AFt), refine pores, effectively improve the performance of the internal interface transition zone of the mixture, make the microstructure of the mixture denser, and improve the strength and shrinkage performance of RCSM. This study provides technical support for the reuse of resources and the sustainable development of road construction. [ABSTRACT FROM AUTHOR]

Integrating waste and industrial by-products into concrete is an alternative way to reduce global cement consumption, enhancing its eco-friendliness. In this context, residues with fly ash have been increasingly utilised. Considering the vulnerability of concrete with fly ash to carbonation and, at the same time, its high resistance to chlorides, it is important to investigate the behaviour of these concretes under their combined actions. For this purpose, an experimental investigation was conducted, studying mortar and concrete specimens with 40% replacement of cement with fly ash. These specimens were subjected to a combination of actions (Cl− and CO2) in two phases: initially through immersion and drying tests, and subsequently through a combination of accelerated tests. Concerning the chloride impact study, free and total chloride profiles were studied. Concerning the impact of carbonation, colourimetric and chemical tests were used. The results demonstrate a significant influence of combined action not only on chloride penetration in cement-based materials with fly ash but also on the development of a carbonation front. Exposure of cement-based materials with fly ash to environments with high Cl− and CO2 content sequentially may lead, on the one hand, to an increase in carbonation resistance. However, on the other hand, it may result in a substantial reduction in chloride penetration resistance. [ABSTRACT FROM AUTHOR]

In light of the urgent need to develop environmentally friendly materials that, at some point, will allow the reduction of concrete and, consequently, cement consumption—while at the same time allowing the reuse of waste and industrial by-products—alkali-activated fly ash (AAFA) geopolymer composite emerges as a material of great interest. The aim of this study was to investigate the physico-mechanical performance of composites based on AAFA binders and the effect of different types of aggregates on these properties. The experimental results indicate variations in flexural and compressive strength, which are influenced both by the nature and particle size distribution of aggregates and the binder-to-aggregate ratio. The analysis of the samples highlighted changes in porosity, both in distribution and pore size, depending on the nature of the aggregates. This supports the evolution of physico-mechanical performance indicators. [ABSTRACT FROM AUTHOR]

The purpose of this study is to synthesize geopolymer binders as an environmentally friendly alternative to conventional cement using available local raw materials. Waste materials such as chalcedonite (Ch), amphibolite (A), fly ash from lignite combustion (PB), and diatomite dust (D) calcined at 900 °C were used to produce geopolymer binders. Metakaolin (M) was used as an additional modifier for binders based on waste materials. The base materials were subjected to fluorescence X-ray fluorescence (XRF) analysis and X-ray diffractometry (XRD) to determine chemical and phase composition. A laser particle size analysis was also performed. The various mixtures of raw materials were activated with a 10 M solution of NaOH and sodium water glass and then annealed for 24 h at 60 °C. The produced geopolymer binders were conditioned for 28 days under laboratory conditions and then subjected to microstructural analysis (SEM) and flexural and compressive strength tests. The best compressive strength results were obtained by the Ch + PB samples—more than 57 MPa, while the lowest results were obtained by the Ch + D+A + M samples—more than 20 MPa. On the other hand, as a result of the flexural strength tests, the highest flexural results were obtained by D + A + M + PB binders—more than 12 MPa, and the lowest values were obtained by binders based on Ch + D+A + M—about 4.8 MPa. [ABSTRACT FROM AUTHOR]

Sustainable zero cement-based one-part ambient cured alkali-activated engineered composites (AAECs) are developed. The durability and microstructural characteristics of developed AAECs using 2% v/v polyvinyl alcohol (PVA) fibers, silica sand, binary or ternary combinations of precursors (fly ash class C 'FA-C', fly ash class F 'FA-F' and ground granulated blast furnace slag 'GGBFS') and two types of powder form alkaline reagents (Type 1 and Type 2) are evaluated compared to conventional engineered cementitious composites (ECCs) and alkali-activated mortars (AAMs) without fiber. AAECs developed satisfactory compressive strength ranging from 34 MPa to 46 MPa. Expansion/shrinkage and mass change (loss/gain) behaviors are affected by binary/ternary combination of source materials, reagent types and curing regimes (water or ambient) for both AAMs and AAECs. The binary (FA-C + GGBFS) and reagent 2 (calcium hydroxide + sodium sulfate) composites demonstrated lower shrinkage due to formation of crystalline C-A-S-H/C-S-H binding phases than their ternary (FA-C + FA-F + GGBFS) and reagent 1 (calcium hydroxide + sodium metasilicate) counterparts which formed amorphous N-C-A-S-H/N-A-S-H phases. The matrix densification due to the formation of reaction products and fiber-induced micro-confinement leads to lower shrinkage and mass change of AAECs compared to their AAM counterparts. Composites exhibited lower or comparable secondary sorptivity indices compared to control ECC, indicating their superior permeation performance. All AAECs had a relative dynamic modulus of elasticity (RDME) greater than 90% at 300 cycles (comparable to control ECC), exhibiting satisfactory freeze–thaw resistance with reagent 2 mixes showing better performance compared to those with reagent 1. The production feasibility of strain hardening AAECs with powder form reagents having satisfactory mechanical and durability properties is confirmed. [ABSTRACT FROM AUTHOR]

This research investigates the feasibility of developing clay composites using natural materials and incorporating waste by-products suitable for plastering diverse support structures. The study identified a versatile composition suitable for a wide range of support materials and explored the potential of revaluing industrial waste and by-products by reintegrating them into the Circular Economy. The experimental investigation outlines the process of evaluating the influence of different raw materials on the performance of the clay composite. The findings confirm that using limestone sludge and fly ash as additives to clay contributes to reducing axial shrinkage and increasing mechanical strengths, respectively. The optimal percentage of additives for the clay used are identified and provided. Using hydraulic lime as a partial substitute for clay reduces the apparent density of dried clay composites, axial shrinkage, and fissures formation while improving adhesion to the substrate. Introducing dextrin into this mix increases the apparent density of the hardened plaster while keeping axial shrinkage below the maximum threshold indicated by the literature. Mechanical strengths improved, and better compatibility in terms of adhesion to the support was achieved, with composition S3 presenting the best results and a smooth, fissure-free plastered surface after drying. [ABSTRACT FROM AUTHOR]

The utilization of carbon dioxide and combustion products in cost- and energy-efficient technologies is an important element of creating sustainable energy systems, particularly in the transition period towards carbon neutrality and in light of the latest political developments, when solid fuels are still competing for a dominant role in securing energy supplies. Within the study presented, bituminous coal-derived fluidized bed fly ash samples of high calcium content, treated using a dry carbonation method under ambient conditions, were tested in terms of their specific properties to determine their usability in the preparation of injection mixtures for the filling of voids after shallow mining activities and other selected geo-engineering techniques. The study goes beyond the existing literature in terms of the carbonation method used, alkaline earth metal source, scale of the experiment, process conditions employed and product application studied. The results showed that the bituminous coal-derived fluidized bed fly ash, carbonated using the direct method adopted, may be successfully employed as the main solid component (over 82% w/w) of the injection mixtures for filling voids after shallow mining activities. The achievable compressive strength of a few MPa makes these materials applicable also in terms of ground strengthening in case it is required in light of the expected land development options to be employed. All principal materials used in the injection mixtures developed (carbonated fluidized bed fly ash, carbon dioxide, bottom ash) are industrial waste, and the carbonation method employed is simple and performed under ambient conditions, which reduces the required energy and cost input of filling mixture production, avoids the surface waste storage requirements, and contributes to the development of low energy-intensive carbon dioxide utilization and solid waste valorization methods. [ABSTRACT FROM AUTHOR]

In recent years, the reuse of industrial waste has become increasingly important for sustainable development. Therefore, this study investigated the application of granulated blast furnace slag (GBFS) as a cementitious replacement material in fly-ash-based geopolymer mortar containing silica fume (GMS). The performance changes in the GMS samples manufactured with different GBFS ratios (0–50 wt%) and alkaline activators were evaluated. The results indicated that GBFS replacement from 0 wt% to 50 wt% significantly affects GMS performance, including improving the bulk density from 2235 kg/m3 to 2324 kg/m3, flexural-compressive strength from 5.83 MPa to 7.29 MPa and 63.5 MPa to 80.2 MPa, respectively; a decrease in water absorption and chloride penetration, and an improvement in the corrosion resistance of GMS samples. The GMS mixture containing 50 wt% GBFS demonstrated the best performances with notable results regarding strength and durability. Owing to the increased production of C-S-H gel, the microstructure of the GMS sample containing more GBFS was denser, as obtained via the scanning electron micrograph analysis results. Incorporating the three industrial by-products into geopolymer mortars was verified when all samples were determined to be in accordance with the relevant Vietnamese standards. The results demonstrate a promising method to manufacture geopolymer mortars that aid sustainable development. [ABSTRACT FROM AUTHOR]

There is an ever-growing interest in recovering and recycling waste materials due to their hazardous nature to the environment and human health. Recently, especially since the beginning of the COVID-19 pandemic, disposable medical face masks have been a major source of pollution, hence the rise in studies being conducted on how to recover and recycle this waste. At the same time, fly ash, an aluminosilicate waste, is being repurposed in various studies. The general approach to recycling these materials is to process and transform them into novel composites with potential applications in various industries. This work aims to investigate the properties of composites based on silico-aluminous industrial waste (ashes) and recycled polypropylene from disposable medical face masks and to create usefulness for these materials. Polypropylene/ash composites were prepared through melt processing methods, and samples were analyzed to get a general overview of the properties of these composites. Results showed that the polypropylene recycled from face masks used together with silico-aluminous ash can be processed through industrial melt processing methods and that the addition of only 5 wt% ash with a particle size of less than 90 µm, increases the thermal stability and the stiffness of the polypropylene matrix while maintaining its mechanical strength. Further investigations are needed to find specific applications in some industrial fields. [ABSTRACT FROM AUTHOR]

The carbonation of alkaline industrial wastes is a pressing issue that is aimed at reducing CO2 emissions while promoting a circular economy. In this study, we explored the direct aqueous carbonation of steel slag and cement kiln dust in a newly developed pressurized reactor that operated at 15 bar. The goal was to identify the optimal reaction conditions and the most promising by-products that can be reused in their carbonated form, particularly in the construction industry. We proposed a novel, synergistic strategy for managing industrial waste and reducing the use of virgin raw materials among industries located in Lombardy, Italy, specifically Bergamo–Brescia. Our initial findings are highly promising, with argon oxygen decarburization (AOD) slag and black slag (sample 3) producing the best results (70 g CO2/kg slag and 76 g CO2/kg slag, respectively) compared with the other samples. Cement kiln dust (CKD) yielded 48 g CO2/kg CKD. We showed that the high concentration of CaO in the waste facilitated carbonation, while the presence of Fe compounds in large amounts caused the material to be less soluble in water, affecting the homogeneity of the slurry. [ABSTRACT FROM AUTHOR]

Traditional silicate cement materials produce a large amount of CO2 during production, making it urgent to seek alternatives. Alkali-activated slag cement is a good substitute, as its production process has low carbon emissions and energy consumption, and it can comprehensively utilize various types of industrial waste residue while possessing superior physical and chemical properties. However, the shrinkage of alkali-activated concrete can be larger than that of traditional silicate concrete. To address this issue, the present study utilized slag powder as the raw material, sodium silicate (water glass) as the alkaline activator, and incorporated fly ash and fine sand to study the dry shrinkage and autogenous shrinkage values of alkali cementitious material under different content. Furthermore, combined with the change trend of pore structure, the impact of their content on the drying shrinkage and autogenous shrinkage of alkali-activated slag cement was discussed. Based on the author's previous research, it was found that by sacrificing a certain mechanical strength, adding fly ash and fine sand can effectively reduce the drying shrinkage and autogenous shrinkage values of alkali-activated slag cement. The higher the content, the greater the strength loss of the material and the lower the shrinkage value. When the fly ash content was 60%, the drying shrinkage and autogenous shrinkage of the alkali-activated slag cement mortar specimens decreased by about 30% and 24%, respectively. When the fine sand content was 40%, the drying shrinkage and autogenous shrinkage of the alkali-activated slag cement mortar specimens decreased by about 14% and 4%, respectively. [ABSTRACT FROM AUTHOR]

Waste incineration is a widely used treatment method, and sustainable approaches are required to properly recycle large volumes of incineration ash to reduce environmental impacts and landfill space consumption. Studies have focused on the potential of recycling incineration ash as a replacement for natural aggregates in civil engineering applications, such as road construction. However, industrial waste incineration ash, such as waste tire incineration ash, contains hazardous heavy metals, such as lead and zinc that pose potential environmental threats. Moreover, few studies have investigated the leachability of these hazardous metals after long-term natural aging. This study investigates the long-term evolution of leachate chemistry, mineralogical transformation, and heavy metal fixation performance of a recycled roadbed material using ash from industrial waste incineration of waste tires and biomass (SFA). Additionally, field samples from a five-year pilot test site utilizing SFA were also examined. Regulatory leaching tests showed that the concentrations of Cd, Pb, As, T-Cr, and Ni were all below permissible limits even after five years of utilization. Long-term column leaching experiment results indicated that, compared to the total content of the SFA material, the leaching ratios of Pb, T-Cr, Cu, and Zn were 27%, 12%, 5%, and 0.1%, respectively. The SFA pH-stat leaching test results demonstrated that the mass release of the total content of heavy metals was relatively minimal, even under acidic pH conditions (pH < 4). Finally, profiles of pH and major ions in leachate from the column leaching experiment were simulated using HYDRUS HP1, implementing a dual-porosity modeling approach. In conclusion, despite containing hazardous heavy metals, SFA exhibits significantly low leaching rates over a long-term period. [ABSTRACT FROM AUTHOR]

Poland is a country where the commercial power industry mainly uses coal to produce energy. As a result of energy production processes, by-products of combustion are generated, primarily fly ashes. In Poland, these are mostly obtained from conventional coal combustion boilers. Fly ashes from coal combustion account for 1.2% of all industrial waste generated in Poland. In addition, fly ashes are produced by fluidized-bed boilers. These are classified as a mixture of fly ashes and solid calcium-based reaction waste from flue-gas desulphurization, and constitute almost 2% of Polish industrial waste. This paper describes the amounts of fly ashes generated in Poland and considers activities related to their recovery and disposal. The high recovery levels of fly ashes (about 90%) and fluidized ashes (about 98%) mean that these waste products can also be considered anthropogenic raw materials. The use of these materials in the cement industry is an example of industrial symbiosis. Such usage benefits not only the economy but also the environment and, therefore, society as a whole. To describe the use of recovered fly ashes in cement plants, the authors use the anthropogenicity index, which characterizes the level of technological advancement and the substitutability of primary raw materials for secondary raw materials. [ABSTRACT FROM AUTHOR]

Water is a resource that is essential to almost all phases of industrial and manufacturing operations globally. It is important to handle the wastewater generated professionally. The textile industry is one of the major global polluters, with textile producers responsible for one-fifth of all industrial water pollution worldwide. In contrast, heavy metal contamination has developed into a critical, expanding global environmental problem. Geopolymer is a cementitious constituent of amorphous aluminosilicates derived from natural or industrial wastes. It is produced using the polymerization of aluminosilicate raw ingredients in an alkaline atmosphere. The aim of this study is to evaluate the application of eco-friendly geopolymer cement in the immobilization technique for the treatment of wastewater including heavy metals and dyes. Geopolymer cement pastes were organized using slag and fly ash as an aluminosilicate source, (1:1) sodium silicate and sodium hydroxide 15 wt.% as an alkali activator in the presence of organic dye pollutant reactive red 195, and Cu2+ ions (700 ppm) at different hydration times for up to 28 days. The physicochemical and mechanical properties of the prepared geopolymer cement mixes were further examined in relation to reactive dye pollutant and Cu2+ ions. The hydration characteristic was examined using the compressive strength and % of total porosity tests, as well as FTIR and XRD studies. Our findings support the 100% immobilization of both Cu2+ ions and organic dye pollutants in prepared geopolymer pastes for up to 28 days of hydration. Additionally, adding both Cu2+ ions and dye pollutants to the prepared geopolymer paste improves its mechanical properties, which is also supported by FTIR data. XRD and FTIR studies showed that the Cu2+ ions and dying bath effluent addition have no influence on the kind of hydration products that are produced. On the other hand, the geopolymerization process is negatively impacted by the presence of Cu2+ ions alone in the geopolymer paste. [ABSTRACT FROM AUTHOR]

Cementitious material based on synergistic industrial wastes can be used as a new product for low-carbon transformation. It can aid in resource recycling and suitable consumption and utilisation of various industrial wastes. The proposed material can reduce a large amount of CO2 emitted during calcination in cement production and the decomposition of raw limestone. In addition, the material exhibits high durability and high resistance to corrosion in the marine environment that can further reduce CO2 emissions over the lifecycle of the carbon footprint of the building. Currently, many similar chemical kinetic processes and mineralogical reaction processes of particle migration and rebinding exist in the hydration and hardening reactions, service processes and durability evolution of different industrial waste cementitious systems for low-carbon production. The theoretical basis of preparing various low-carbon cementitious materials (LCCMs) with industrial waste systems is discussed herein, including the two theories of 'complex salt effect' and 'isomorphic effect from tetrahedral coordination of silicon-oxygen'. Further research on LCCM is based on the theoretical foundation of 'passive hydration kinetics'. Furthermore, this study presents the CO2 reduction potential of LCCM prepared using industrial wastes and provides future research directions in this regard. [ABSTRACT FROM AUTHOR]

Currently, there is an increasing industrial demand for rare earth elements (REE) as these elements are now integral to the manufacture of many carbon-neutral technologies. The depleting REE ores and increasing mining costs are prompting us to consider alternative sources for these valuable metals, particularly from waste streams. Although REE concentrations in most of the alternative resources are lower than current REE ores, some sources including marine sediments, coal ash, and industrial wastes, such as red mud, are emerging as promising with significant concentrations of REE. This review focuses on the alternative resources for REE, such as ocean bottom sediments, continental shelf sediments, river sediments, stream sediments, lake sediments, phosphorite deposits, industrial waste products, such as red mud and phosphogypsum, coal, coal fly ash and related materials, waste rock sources from old and closed mines, acid mine drainage, and recycling of e-waste. Possible future Moon exploration and mining for REE and other valuable minerals are also discussed. It is evident that REE extractions from both primary and secondary ores alone are not adequate to meet the current demand, and sustainable REE recovery from the alternative resources described here is also necessary to meet the growing REE demand. An attempt is made to identify the potential of these alternative resources and sustainability challenges, benefits, and possible environmental hazards to meet the growing challenges of reaching the future REE requirements. [ABSTRACT FROM AUTHOR]

In order to alleviate the shortage of sand resources for construction, make full use of industrial waste and promote the development of green lightweight aggregate concrete in the desert and surrounding areas, this paper proposes a new lightweight ceramsite concrete, fly ash cenospheres and desert sand ceramsite concrete (FDCC). An orthogonal test was conducted to analyze the effects of the desert sand (DS) replacing ratio, fly ash cenosphere (FAC) replacing ratio and polymer emulsion (PLE) addition on the damage patterns, slump, apparent density and compressive strength of the FDCC. The results showed that the most influential factors for the slump, apparent density and compressive strength of the FDCC were the FAC replacing ratio, FAC replacing ratio and DS replacing ratio, respectively. Meanwhile, the PLE addition had little effect on the workability or mechanical performance of the FDCC. With the increase in the DS replacing ratio, the slump decreased rapidly and the compressive strength reached its peak value, increasing by 20.6% when the DS replacing ratio was 20%. With the increase in the FAC replacing ratio, the slump increased by 106%, the apparent density decreased gradually and the compressive decreased and then increased, reaching its lowest value when the FAC replacing ratio was 20%. According to the synthetic evaluation analysis, the optimum DS replacing ratio, FAC replacing ratio and PLE addition of the FDCC were 20%, 30% and 1%, respectively. [ABSTRACT FROM AUTHOR]

In recent years, due to the reduction in available natural resources, the attention of many researchers has been focused on the reuse of recycled materials and industrial waste in common engineering applications. This paper discusses the feasibility of using seven different materials as alternative fillers instead of ordinary Portland cement (OPC) in road pavement base layers: namely rice husk ash (RHA), brick dust (BD), marble dust (MD), stone dust (SD), fly ash (FA), limestone dust (LD), and silica fume (SF). To exclusively evaluate the effect that selected fillers had on the mechanical performance of asphalt mixtures, we carried out Marshall, indirect tensile strength, moisture susceptibility, and Cantabro abrasion loss tests on specimens in which only the filler type and its percentage varied while keeping constant all the remaining design parameters. Experimental findings showed that all mixtures, except those prepared with 4% RHA or MD, met the requirements of Indian standards with respect to air voids, Marshall stability and quotient. LD and SF mixtures provided slightly better mechanical strength and durability than OPC ones, proving they can be successfully recycled as filler in asphalt mixtures. Furthermore, a Machine Learning methodology based on laboratory results was developed. A decision tree Categorical Boosting approach allowed the main mechanical properties of the investigated mixtures to be predicted on the basis of the main compositional variables, with a mean Pearson correlation and a mean coefficient of determination equal to 0.9724 and 0.9374, respectively. [ABSTRACT FROM AUTHOR]

Incessant generation and mismanagement of industrial waste, resource scarcity, and environmental degradation have created non-sustainability in human life. Though industrial wastes are hazardous or non-hazardous in nature based on their source, open dumping disposal is commonly done for both types of waste. The adversity associated with waste enhances the environmental and health impacts. However, this waste has the potential to recycle and minimize resource scarcity. The circular economy works on the concept of reuse, recycling, and recovery to convert waste into a resource. Thus, industrial waste can benefit the environment and economic growth to build industrial ecology. However, the opportunities and challenges associated with industrial ecology for the reuse and recycling of waste have to be identified and preserved. Therefore, this study has identified challenges associated with waste, analyzed their impact, and industrial regulations, prioritized their criticality, and developed solution strategies to alleviate them. Two case studies on industrial byproducts, i.e., fly ash and red mud, based on different income groups are discussed in this study. It highlights the circular economy has minimized waste generation and enhanced the recovery of secondary resource materials. In addition, this study supports achieving the sustainable development goals (SDGs) 11 and 12 to build a sustainable industrial ecosystem. [ABSTRACT FROM AUTHOR]

Introduction: the article discusses the effect of the complex of active mineral additives consisting of silica and fly ash, and a fine aggregate, including finely ground natural-white quartz sand for partial replacement of river sand, on the mechanical properties of high-strength concrete containing steel fiber. Materials and methods: high-strength concrete containing Dramix®3D 65/35 steel fiber in the amount of 100 kg per 1 m3 of concrete mixture was suggested where 22% to 100% of river sand was replaced by finely ground white natural sand of the particle size of 5 to 1800 μm and containing the complex of active mineral additives for partial replacement of cement as part of a multicomponent binder, consisting of low-calcium fly ash of thermal power plants and silica and containing, respectively, 20, 30, 40% fly ash and from 5 to 15% silica by weight of the binder. Results: research results have shown that 100% replacement of river sand with finely ground natural white sand, in concrete containing 20% of the mass as part of a multicomponent binder, fly ash and from 5 to 15% by weight of silica, contributes to the increase of its strength properties: the values of concrete compressive strength after 28 days were in the range from 118.5 to 128 MPa, tensile strength during bending and splitting, respectively, from 18.8 to 25.4 MPa and from 10.2 to 11.9 MPa, which is higher than the strength of concrete samples containing river sand. Conclusions: the achieved results have demonstrated the efficiency of using finely ground natural white sand as an alternative to river sand for producing high-strength concrete, thus helping to save the river sand resources in Vietnam. The use of fly ash and micro silicon, which are power and metallurgy wastes, as part of a multicomponent binder in order to partially replace cement reduces the carbon footprint in the production of binders and will also have a beneficial effect on environmental protection against industrial waste pollution. [ABSTRACT FROM AUTHOR]

The paper presents the results of research on a composite mixture intended for use in road construction. The purpose of developing the mixture is to be able to use large amounts of industrial waste to produce building material. The waste used are coal slate from the mining industry, shredded rubber waste from used passenger car tires and fly ash from power plants. The mixture (SRFC) consists of unburnt coal-mining slate (S), shredded rubber waste (R), fly ash (F) and cement(C). A test under cyclic loading conditions was carried out on samples prepared from the SRFC mixture, in which the global deformations and local strains caused on the samples were measured. A measurement system using digital image correlation was used for the research. On the basis of the conducted research, it was found that the content of shredded rubber waste significantly influences the deformability of the tested mixtures and allows for the extension of the scope of elastic deformation in which the tested samples work. [ABSTRACT FROM AUTHOR]

The following article introduces, in a thorough manner, how the chemical pozzolanic reaction takes place in cement composites containing the fly ash (FA) additive. In the research part, however, the development of phases in the structure of the cement paste in the initial period of its curing and after 28 days from its preparation was traced. For this purpose, a Scanning Electron Microscope (SEM) was used. In order to accurately highlight all the characteristic stages of the formation of the structure of the composite containing FA, an analysis of the cement matrix was carried out between 0.5 and 28 days of their curing. Microstructural studies were complemented by tests of pozzolanic activity of FAs used. In order to conduct a full analysis of this feature, experiments were carried out using two types of research methods, i.e., chemical and physical. On the basis on the conducted studies it was found that: in cement composites with the addition of FA, in the period until the third day of curing, the development of the material structure is mainly the result of the hydration reaction, and between the seventh and fourteenth day after sample preparation, the first signs of the pozzolanic reaction on FA grains are visible; however, in the period between 14 and 28 days, there is a clear homogenization of the structure of the cement composite with the addition of FA, resulting from the change of disordered phases into compact and homogeneous forms and filling in the composite of porous places with pozzolanic reaction products. The use of cement composites based on materials whose application makes it possible to reduce GHG emissions to the atmosphere, reduce energy consumption, and reduce industrial waste landfills leads towards the development of ecological and sustainable building engineering. [ABSTRACT FROM AUTHOR]

Geopolymers are high-performance, cost-effective materials made from industrial waste that ideally fit the needs of 3D printing technology used in construction. The novelty of the present work lies in the investigation of methods to mix geopolymer concrete from fly ash (FA) class F, ground granulated blast furnace slag (GGBS), and raw calcined kaolin clay (RCKC) to determine the mixing procedure which provides the best mechanical strength and structural integrity. The experimental results show that aluminosilicates with different reaction parameters when mixed one after another provide the optimal results while the geopolymer concrete possesses the highest compressive strength and the denser structure. The results demonstrated that the reactivity of GGBS, FA, and RCKC increased for different depolymerization speeds of the selected aluminosilicates. This research will provide results on how to improve the mixing order for geopolymer synthesis for 3D printing demands. The highest compressive strength and denser structure of geopolymer concrete is achieved when each type of aluminosilicate is mixed with an alkaline medium separately. [ABSTRACT FROM AUTHOR]

Geopolymer (GP) concrete is a novel construction material that can be used in place of traditional Portland cement (PC) concrete to reduce greenhouse gas emissions and effectively manage industrial waste. Fly ash (FA) has long been utilized as a key constituent in GPs, and GP technology provides an environmentally benign alternative to FA utilization. As a result, a thorough examination of GP concrete manufactured using FA as a precursor (FA-GP concrete) and employed as a replacement for conventional concrete has become crucial. According to the findings of current investigations, FA-GP concrete has equal or superior mechanical and physical characteristics compared to PC concrete. This article reviews the clean production, mix design, compressive strength (CS), and microstructure (Ms) analyses of the FA-GP concrete to collect and publish the most recent information and data on FA-GP concrete. In addition, this paper shall attempt to develop a comprehensive database based on the previous research study that expounds on the impact of substantial aspects such as physio-chemical characteristics of precursors, mixes, curing, additives, and chemical activation on the CS of FA-GP concrete. The purpose of this work is to give viewers a greater knowledge of the consequences and uses of using FA as a precursor to making effective GP concrete. [ABSTRACT FROM AUTHOR]

Adsorption chillers produce cold energy, using heat instead of electricity, thus reducing electrical energy consumption. A major industrial waste, fly ash, can be converted to zeolite and used in adsorption chillers as an adsorbent. In this research, three different types of zeolites were synthesised from fly ash via a hydrothermal reaction in an alkaline solution (NaOH). The obtained samples (Na-A zeolites) were modified with K2CO3 to increase the water adsorption capacity of these samples. Phase and morphology analyses shows that desired zeolites formed properly but other crystalline phases also exist along with nonporous amorphous phases. The determined specific surface areas for Na-A zeolite (12 h) and Na-A zeolite (24 h) are 45 m2/g and 185 m2/g respectively, while the specific surface area for synthesized 13X zeolite is almost negligible. Water-isotherm for each of these samples was measured. Considering the application of adsorption chillers, average adsorption capacity was very low, 1.73% and 1.27%, respectively, for the two most probable operating conditions for synthesized 13X zeolite, whereas no water was available for the evaporation from Na-A zeolite (12 h) and Na-A zeolite (24 h). This analysis implies that among the synthesized materials only 13X zeolite has a potential as an adsorber in sorption chillers. [ABSTRACT FROM AUTHOR]

Magnesium oxychloride cement (MOC), a type of special construction material, has drawn much research attention in solid waste utilization and environmental protection due to its eco-friendly production. Ammonia soda residue (ASR), a by-product generated from sodium carbonate manufacturing, is one of the industrial wastes that can be recycled in MOC systems. However, ASR exhibits adverse effects on the fresh performance and volume stability of MOC pastes. This paper aims at improving the properties of ASR-MOC by introducing fly ash (FA), solid waste from the power industry. Firstly, the roles of FA in MOC pastes are evaluated and analyzed. Then, three substitution ratios of FA (33.3%, 50% and 66.7% in weight) for ASR are designed for MOC pastes with 10% to 40% industrial wastes. Flowability, setting, strength and expansion of all mixtures were experimentally studied. Furthermore, X-ray diffraction (XRD) and scanning electron microscope (SEM) approaches were adopted to illustrate the microstructure changes. Results show that by adding different amounts of FA, the inferior flowability of MOC caused by ASR can be improved by 6–23%, the setting process can be prolonged by 30–55% and the expansion ratio can be reduced by 14–66%. The intensity of characteristic peaks of 5-phase and Mg(OH)2, together with the degrees of crystallization in XRD curves, well explain the strength variation and volume stability of ASR-MOC pastes. According to the regulation of relative specification, up to 20% of solid wastes in weight (10% FA + 10% ASR) can be consumed, contributing greatly to the greener sustainable development of construction materials. [ABSTRACT FROM AUTHOR]

Phosphorus slag (PS), an industrial waste slag, has been used in geopolymers because it is rich in silicon and calcium. The poor performance of phosphorus slag-based geopolymer is due to its aluminum deficiency. In this work, low-calcium fly ash, treated by a wet-grinding process, named wet-grinding ultrafine fly ash (WUFA) was used as an Al supplement to replace some of the phosphorus slag, and the wet-grinding, ultrafine fly ash-phosphorus slag (WUFA-PS)-based geopolymer was prepared. The effects of the substitution amount of WUFA and the activator dosage on the hydration properties, mechanical properties, pore structure and SEM of the WUFA-PS geopolymer were discussed in detail. The results indicate that WUFA and more activators contribute to the Al and high alkalinity environment, which positively induces the production of more geopolymer gels, thus releasing more heat and optimizing the pore structure of the matrix. The compressive strength increased by up to 28.1%. The enhanced performance of the WUFA-PS-based geopolymer may also arise from the filling effect and activity improvement of WUFA. This study has proved the feasibility of preparing a geopolymer by blending wet-grinding ultrafine fly ash and phosphorus slag and has provided references for the ratio and performance evaluation of WUFA-PS-based geopolymer concrete. [ABSTRACT FROM AUTHOR]

A main global challenge is finding an alternative material for cement, which is a major source of pollution to the environment because it emits greenhouse gases. Investigators play a significant role in global waste disposal by developing appropriate methods for its effective utilization. Geopolymers are one of the best options for reusing all industrial wastes containing aluminosilicate and the best alternative materials for concrete applications. Waste wood ash (WWA) is used with other waste materials in geopolymer production and is found in pulp and paper, wood-burning industrial facilities, and wood-fired plants. On the other hand, the WWA manufacturing industry necessitates the acquisition of large tracts of land in rural areas, while some industries use incinerators to burn wood waste, which contributes to air pollution, a significant environmental problem. This review paper offers a comprehensive review of the current utilization of WWA with the partial replacement with other mineral materials, such as fly ash, as a base for geopolymer concrete and mortar production. A review of the usage of waste wood ash in the construction sector is offered, and development tendencies are assessed about mechanical, durability, and microstructural characteristics. The impacts of waste wood ash as a pozzolanic base for eco-concreting usages are summarized. According to the findings, incorporating WWA into concrete is useful to sustainable progress and waste reduction as the WWA mostly behaves as a filler in filling action and moderate amounts of WWA offer a fairly higher compressive strength to concrete. A detail study on the source of WWA on concrete mineralogy and properties must be performed to fill the potential research gap. [ABSTRACT FROM AUTHOR]

For the purpose of designing the adsorption systems, adsorption isotherm models provide information on the adsorption process. 10.3390/polym14050914 8 Buema G., Harja M., Lupu N., Chiriac H., Forminte L., Ciobanu G., Bucur D., Bucur R.D. Adsorption performance of modified fly ash for copper ions removal from aqueous solution. 10.3390/w13131725 13 Wang R., Deng L., Fan X., Li K., Lu H., Li W. Removal of heavy metal ion cobalt (II) from wastewater via adsorption method using microcrystalline cellulose-magnesium hydroxide. "Advanced Materials for Water Remediation" is a Special Issue of I Materials i , which will take into consideration all the papers discussing the synthesis, characterization and application of advanced materials for water remediation. [Extracted from the article]

Beneficiation of industrial wastes, such as mine tailings (MTs), through development of alternative eco-friendly geopolymer binders for construction composites offers a twofold environmental benefit, as it reduces the demand for cement and it increases the sustainability of industrial processes by creating a value-added product from an industrial byproduct. While MTs have the requisite composition for use as a geopolymer precursor, they are often low-reactive. This study explored the effect of Class C Fly Ash (FAc) on the geopolymerization of low-reactive gold MTs. A 10 M sodium hydroxide (NaOH) solution was used as the alkaline activator with four different concentrations of FAc (5, 10, 15 and 20 wt.%). The results indicated that the combination of FAc with the low-reactive gold MTs improved the physicochemical stability of the final geopolymerized samples, with a 95–120% increase in compressive strength, compared to the geopolymer samples of only low-reactive gold MTs. Although some of the strength improvement could be attributed to geopolymerization of the FAc itself, the presence of the FAc also improved the reactivity of the MTs, increasing the geopolymer production of the MTs. This study documents the positive effects of the FAc on gold MTs with low-calcium content and their conversion into sustainable inorganic composite geopolymers for the construction field. [ABSTRACT FROM AUTHOR]

The construction industry is the world's largest emitter of greenhouse gases. The CO2 emission levels in the atmosphere are already reaching a tipping point and could cause severe climate change. An important element is the introduction of a technology that allows for the capture and sequencing of carbon dioxide levels, reducing both emissions and the carbon footprint from the production of Portland cement and cement-based building materials. The European Union has started work on the European Climate Law, establishing the European Green Deal program, which introduces the achievement of climate neutrality in the European Union countries. This includes a new policy of sustainable construction, the aim of which is to develop products with a closed life cycle through proper waste management. All efforts are being made to create generated waste and thus to support their production and/or use as substitutes for raw materials to produce biocomposites. This article reviews environmental issues and characterizes selected waste materials from the agri-food, mineral, and industrial sectors with specific properties that can be used as valuable secondary raw materials to produce traditional cements and biocomposite materials, while maintaining or improving their mechanical properties and applications. [ABSTRACT FROM AUTHOR]

This study aimed to investigate the recycling opportunities for industrial byproducts and their contribution to innovative concrete manufacturing processes. The attention was mainly focused on municipal solid waste incineration fly ash (MSWI-FA) and its employment, after a washing pre-treatment, as the main component in artificially manufactured aggregates containing cement and ground granulated blast furnace slag (GGBFS) in different percentages. The produced aggregates were used to produce lightweight concrete (LWC) containing both artificial aggregates only and artificial aggregates mixed with a relatively small percentage of recycled polyethylene terephthalate (PET) in the sand form. Thereby, the possibility of producing concrete with good mechanical properties and enhanced thermal properties was investigated through effective PET reuse with beneficial impacts on the thermal insulation of structures. Based on the obtained results, the samples containing artificial aggregates had lower compressive strength (up to 30%) but better thermal performance (up to 25%) with respect to the reference sample made from natural aggregates. Moreover, substituting 10% of recycled aggregates with PET led to a greater reduction in resistance while improving the thermal conductivity. This type of concrete could improve the economic and environmental aspects by incorporating industrial wastes—mainly fly ash—thereby lowering the use of cement, which would lead to a reduction in CO2 emissions. [ABSTRACT FROM AUTHOR]

The development of geopolymers is in line with the requirements of sustainable development. Creating a new type of material from various industrial and bio-based wastes and by-products can lead to reduced energy consumption, reduced waste generation, reduced global CO2 emissions, as well as reduced resource extraction of natural resources. In this study, geopolymer composites based on class F fly ash with the addition of fine quartz sand and ground walnut shells used as a substitute for sand were examined. The study focused on investigating the effects of different weight percentages of ground walnut shells and quartz sand on the density and strength properties, including compressive and flexural strength, thermal conductivity, efflorescence formation, and water absorption of the fly ash-based geopolymer composites. The microstructure of the studied geopolymers was also analyzed using a scanning electron microscope (SEM). It was observed that the addition of ground walnut shells contributes to the decrease in density and mechanical properties, increase in absorption properties, and decrease in porosity of fly ash-based geopolymers. Furthermore, the addition of ground walnut shells allows for a significant reduction in efflorescence on the surface of the tested geopolymer composites. Moreover, partial or complete replacement of sand by ground walnut shells in geopolymer composites based on fly ash allows for a significant reduction in their thermal conductivity, which makes it possible to use these composites as insulation materials. [ABSTRACT FROM AUTHOR]

Four industrial wastes, i.e., blast furnace slag, steel slag, desulfurization ash, and phosphoric acid sludge, were used to prepare a low-carbon binder, metallurgical slag-based cementitious material (MSCM). The feasibility of solidification/stabilization of municipal solid waste incineration (MSWI) fly ashes by MSCM were evaluated, and the immobilization mechanisms of heavy metals were proposed. The MSCM paste achieved 28-day strength of 35.2 MPa, showing its high-hydration reactivity. While the fly ash content was as high as 80 wt.%, the 28-day strength of MSCM-fly ash blocks reached 2.2 MPa, and the leaching concentrations of Pb, Zn, Cr, and Hg were much lower than the limit values of the Chinese landfill standard (GB 16889-2008). The immobilization rates of each heavy metal reached 98.75–99.99%, while four kinds of MSWI fly ashes were solidified by MSWI at fly ash content of 60 wt.%. The 28-day strength of binder-fly ash blocks had an increase of 104.92–127.96% by using MSCM to replace ordinary Portland cement (OPC). Correspondingly, the lower leachability of heavy metals was achieved by using MSCM compared to OPC. The mechanisms of solidification/stabilization treatment of MSWI fly ash by MSCM were investigated by XRD, SEM, and TG-DSC. Numerous hydrates, such as calcium silicate hydrate (C-S-H), ettringite (AFt), and Friedel's salt, were observed in hardened MSCM-fly ash pastes. Heavy metals from both MSWI fly ash and MSCM could be effectively immobilized via adsorption, cation exchange, precipitation, and physical encapsulation. [ABSTRACT FROM AUTHOR]

White mud is residue discharged during the acid method in the aluminum extraction process from coal fly ash, and this material is harmful to the environment. The implementation of an environmentally friendly and valuable way to use white mud is a key factor restricting the commercial application of the acid method in the fly ash alumina extraction technology. An analysis of white mud revealed the following: (1) it was highly enriched in SiO2 (70–80%) while concentrations of acid-soluble elements, such as Na, Al, and Fe, and some hazardous heavy metals, including Pb and Cr, were significantly lower than raw fly ash; (2) approximately 80% of SiO2 had relatively high reaction activity because of the foregoing Al-extraction treatment. Through an ingenious green chemical process, the complete conversion of white mud into silicon–calcium fertilizer (SCF) was achieved under very mild reaction conditions (approximately 100 °C and atmospheric pressure). Waste liquor was totally recycled, and no secondary solid waste was generated. The SCF had an available silicon content (ASC) of 35%, significantly higher than the commercial standard (20%). Converting them into soil conditioners or ecological remediation materials with the lowest possible energy consumption and secondary pollution may be the most promising approach for the future disposal of aluminosilicate industrial solid wastes. [ABSTRACT FROM AUTHOR]

35207993 10 Cheng Z., Cheng X., Xie Y., Ma Z., Liu Y. Strength Tests and Numerical Simulations of Loess Modified by Desulfurization Ash and Fly Ash. This Special Issue, titled "Research and Development of Building Materials Based on Industrial Waste", is focused on the preparation and description of the properties of new building materials based on industrial waste that are to be used in practice in civil engineering and engineering construction. 35009234 12 Liu H., Tian Z., Fan H. A Study on the Relationships between Water Film Thickness, Fresh Properties, and Mechanical Properties of Cement Paste Containing Superfine Basalt Powder (SB). [Extracted from the article]

The fabrication of bricks commonly consumes relatively high natural resources. To reduce the carbon footprint in the brick production industry, repurposing industrial wastes in the making of sustainable bricks is a recent trend in research and application. Local wastes, such as oil palm shell (OPS), palm oil fuel ash (POFA), and quarry dust (QD), are massively produced annually in the palm oil-exporting countries. Moreover, QD from mining industries is hazardous to both water and air quality. For better waste management in marching towards sustainability, these wastes should be given their second life as construction materials. Therefore, this paper investigates the possibility of incorporating agro-industrial wastes into the brick mixture by examining their properties by means of several standardized tests. For the mix design, a 100% replacement of coarse aggregate with OPS, 20% replacement of cement with POFA, 20% cement weight of limestone as admixture, and 0 to 50% replacements of fine aggregate with QD are experimentally considered. The optimum mix of these wastes is preliminarily determined by focusing on high compressive strength as an indicator. Other examinations include splitting tensile, flexural strength, water absorption, and efflorescence tests. Although the agro-industrial waste cement brick is 18% lower in the strength to weight ratio compared to that of conventional, it is observed that it has better late strength development due to its POFA pozzolanic properties. Moreover, the proposed green cement brick is further checked for compliance with several standards for feasible use in the construction industry. Financially, the cost for the brick with the new mix design is almost equivalent to that of conventional. Hence, this green cement brick is reasonable to be employed in the construction industry to promote material sustainability for better waste management. [ABSTRACT FROM AUTHOR]

The use of more eco-efficient cements in concretes is one of the keys to ensuring construction industry sustainability. Such eco-efficient binders often contain large but variable proportions of industrial waste or by-products in their composition, many of which may be naturally occurring radioactive materials (NORMs). This study explored the application of a new gamma spectrometric method for measuring radionuclide activity in hybrid alkali-activated cements from solid 5 cm cubic specimens rather than powder samples. The research involved assessing the effect of significant variables such as the nature of the alkaline activator, reaction time and curing conditions to relate the microstructures identified to the radiological behavior observed. The findings showed that varying the inputs generated pastes with similar reaction products (C-S-H, C-A-S-H and (N,C)-A-S-H) but different microstructures. The new gamma spectrometric method for measuring radioactivity in solid 5 cm cubic specimens in alkaline pastes was found to be valid. The variables involved in hybrid cement activation were shown to have no impact on specimen radioactive content. The powder samples, however, emanated 222Rn (a descendent of 226Ra), possibly due to the deformation taking place in fly ash structure during alkaline activation. Further research would be required to explain that finding. [ABSTRACT FROM AUTHOR]

Geopolymers, or also known as alkali-activated binders, have recently emerged as a viable alternative to conventional binders (cement) for soil stabilization. Geopolymers employ alkaline activation of industrial waste to create cementitious products inside treated soils, increasing the clayey soils' mechanical and physical qualities. This paper aims to review the utilization of fly ash and ground granulated blast furnace slag (GGBFS)-based geopolymers for soil stabilization by enhancing strength. Previous research only used one type of precursor: fly ash or GGBFS, but the strength value obtained did not meet the ASTM D 4609 (<0.8 Mpa) standard required for soil-stabilizing criteria of road construction applications. This current research focused on the combination of two types of precursors, which are fly ash and GGBFS. The findings of an unconfined compressive strength (UCS) test on stabilized soil samples were discussed. Finally, the paper concludes that GGBFS and fly-ash-based geo-polymers for soil stabilization techniques can be successfully used as a binder for soil stabilization. However, additional research is required to meet the requirement of ASTM D 4609 standard in road construction applications, particularly in subgrade layers. [ABSTRACT FROM AUTHOR]

Downsizing fossil fuel dependence and greenhouse gas emissions is at the forefront of a sustainable future. The expansion of renewable energy while striving to minimize dependence on fossil fuels has led to biomass taking the lead among renewable energy sources, with wood having the broadest application. Along with the growing trend of using biomass as a renewable energy source, the combustion of wood biomass results in wood biomass ash (WBA), leading to compelling amounts of waste. In this study, the technical feasibility of fly WBA from different Croatian power plants was analyzed to evaluate its potential use in precast concrete drainage elements and curb units. By implementing a performance-based design, the influence of various factors in thermal processing of wood biomass was investigated, together with a detailed characterization of WBA in order to assess the feasibility of using WBA as a secondary raw material in a large-scale industrial batching plant. The compressive strength and durability properties (water absorption, permeability, and freeze–thaw resistance) of concrete mixtures with WBA as a replacement for 15 wt% cement were evaluated and compared with the precast concrete manufacturer's technical requirements. The main concerns identified were compositional inconsistency of WBA, workability downturn, delay in initial reactivity rate, and increased water absorption. Concrete with WBA based on a circular design has been found to be a viable solution to cement depletion, stepping up from recycling to reuse of industrial waste. [ABSTRACT FROM AUTHOR]

Environmental pollution is one of the major concerns throughout the world. The rise of industrialization has increased the generation of waste materials, causing environmental degradation and threat to the health of living beings. To overcome this problem and effectively handle waste materials, proper management skills are required. Waste as a whole is not only waste, but it also holds various valuable materials that can be used again. Such useful materials or elements need to be segregated and recovered using sustainable recovery methods. Agricultural waste, industrial waste, and household waste have the potential to generate different value-added products. More specifically, the industrial waste like fly ash, gypsum waste, and red mud can be used for the recovery of alumina, silica, and zeolites. While agricultural waste like rice husks, sugarcane bagasse, and coconut shells can be used for recovery of silica, calcium, and carbon materials. In addition, domestic waste like incense stick ash and eggshell waste that is rich in calcium can be used for the recovery of calcium-related products. In agricultural, industrial, and domestic sectors, several raw materials are used; therefore, it is of high economic interest to recover valuable minerals and to process them and convert them into merchandisable products. This will not only decrease environmental pollution, it will also provide an environmentally friendly and cost-effective approach for materials synthesis. These value-added materials can be used for medicine, cosmetics, electronics, catalysis, and environmental cleanup. [ABSTRACT FROM AUTHOR]

The effects of the fly ash and of the sunflower stalks and corn cobs within a cement-matrix composite were studied under the aspects of density, compressive strength, splitting tensile strength, elasticity modulus, and resistance to repeated freeze-thaw cycles. In the research were developed 20 recipes of cement-based composite, including the reference composite. Fly ash was used as partial cement replacement (10, 20 and 30% by volume), and the vegetal aggregates made by corn cobs and sunflower stalks as partial replacement of the mineral aggregates (25 and 50% by volume). The study results revealed that a lightweight composite can be obtained with 50% of vegetal aggregates, and the fly ash, no matter its percentage, enhanced the compressive strength and splitting tensile strength of the compositions with 50% of sunflower aggregates and the freeze-thaw resistance of all compositions with sunflower stalks. [ABSTRACT FROM AUTHOR]

The stringent demand to develop lightweight materials with enhanced properties suitable for various engineering applications is the focus of this research work. Industrial wastes such as fly ash (FA) and S-glass-fibres (GF) were used as reinforcement materials for high-strength alloy, i.e., Al 7005. Stir casting routes were employed for fabricating the four samples, Al 7005, Al 7005 + 5% GF, Al 7005 + 6% FA and Al 7005 + 5% GF + 6% FA. The extrusion process with different extrusion ratios (ER: 5.32:1, and 2.66:1) was used to examine the properties of all four samples. Extruded samples with ER: 5.32: 1 resulted in equiaxed grains with refined structure compared to stir casting parts. The effect of the extrusion process and the addition of reinforcements (GF and FA) on the gravimetric, electrochemical, and electrochemical impedance corrosion behaviour of Al 7005 composites in 1M HCl (Hydrochloric acid) solution were investigated. The results of all three corrosion methods showed that Al 7005 + 6% FA exhibited higher corrosion resistance. Corrosion rate of Al 7005, Al 7005 + 5% GF, Al 7005 + 6% FA and Al 7005 + 5% GF + 6% FA is found equal to 3.25, 2.41, 0.34, and 0.76 mpy, respectively. The FA particles remain inert and act as a physical barrier with corrosive media during the corrosion test. GF undergoes fibre degradation or disrupts the continuity of the glass network as a result of fibre leaching, which increases the corrosion rate in the sample. The gravimetric study showed that the corrosion rates decreased with an increase in extrusion ratio, which might be due to corrosion passivation increases and improved properties. The scanning electron microscopy reveals that corrosion fits, flakes and micro-cracks were observed more in the as-cast composites than that of extrusion composites, promoting the corrosion rate. [ABSTRACT FROM AUTHOR]

The partial replacement of cement in concrete with the addition of granite powder and fly ash can help to reduce the carbon dioxide (CO2) emissions into the atmosphere associated with cement production. The aim of the article is to compare the performance of granite powder and fly ash for the sustainable production of air-cured cementitious mortars. The morphological, chemical, and granulometric properties of these additives were first compared with the properties of cement. Afterward, a series of mortars modified with the addition of granite powder and fly ash was made. The properties of the fresh mixes and the mechanical properties of the hardened composites were then tested. Finally, based on the obtained results, a cost analysis of the profitability of modifying cementitious composites with granite powder or fly ash was investigated. The obtained results allow similarities and differences between granite powder and fly ash in relation to cement to be shown. To conclude, it should be stated that both of these materials can successfully be used for the sustainable production of air-cured cementitious composites. This conclusion has a significant impact on the possibility of improving the natural environment by reducing the amount of cement production. More sustainable production of cement-based materials could enable CO2 emissions to be decreased. The use of granite powder for the production of cementitious mortars can significantly reduce the amount of this material deposited in landfills. [ABSTRACT FROM AUTHOR]

CO2 mineralization (aka mineral carbonation) is a promising method for the chemical sequestration of CO2 via reaction with oxides of alkaline or alkaline-earth metals to form carbonates. It has documented advantages over similar technological solutions to climate change. The huge amount of industrial solid waste, as a serious environmental issue confronted by China, can provide additional alkalinity sources for CO2 mineralization. In this study, we present an overview of the latest advances in the emerging technologies of CO2-mineralization via industrial solid waste in China, from the perspective of both theoretical and practical considerations. We summarize the types of industrial solid waste that are used (mainly coal fly ash, steel slag, phosphogypsum, and blast furnace slag) and the technological options available in the literature, with an emphasis on the discussion of the involved process-intensification methods and valuable chemicals produced. Furthermore, we illustrate the current status of pertinent policies, and research and development activities in China. Finally, we identify the current knowledge gaps, particularly in understanding the overall sustainability performance of these CO2-mineralization technologies, and indicate that the technical, economic, and environmental challenges of promoting and commercializing these technologies for the co-utilization of industrial solid waste and carbon resources call for, amongst other things, more joint efforts by chemists, chemical engineers, and environmental scientists, and more feedback from the energy and industrial sectors. [ABSTRACT FROM AUTHOR]

Buried pipe design requires knowledge about the fill to design the backfill structure. The interaction between the backfill envelope and the pipe impacts the structural performance of the buried pipe. The backfill material and compaction level respond to the backfill's overall strength and, therefore, for pipe-soil interaction. The strength of backfill material is described in terms of modulus of soil reaction E' and constrained modulus Eode. As the E' is an empirical parameter, the Eode can be measured in the laboratory by performing the oedometer tests. In this study, we have performed extensive oedometric tests on five types of anthropogenic materials (AM). Three of them are construction and demolition materials (C–D materials) namely, recycled concrete aggregate (RCA), crushed brick (CB), and recycled asphalt pavement (RAP). Two of them are industrial solid wastes (ISW) namely, fly ash and bottom slag mix (FA + BS) and blast furnace slag (BFS). The results of the tests revealed that AM behaves differently from natural aggregates (NA). In general, the Eode value for AM is lower than for NA with the same gradation. Despite that, some of AM may be used as NA substitute directly (RCA or BFS), some with special treatment like CB and some with extra compaction efforts like RAP or FA + BS. [ABSTRACT FROM AUTHOR]

Supplementary cementitious materials (SCMs) in industrial waste and by-products are routinely used to mitigate the adverse environmental effects of, and lower the energy consumption associated with, ordinary Portland cement (OPC) manufacture. Many such SCMs, such as type F coal fly ash (FA), are naturally occurring radioactive materials (NORMs). 226Ra, 232Th and 40K radionuclide activity concentration, information needed to determine what is known as the gamma-ray activity concentration index (ACI), is normally collected from ground cement samples. The present study aims to validate a new method for calculating the ACI from measurements made on unground 5 cm cubic specimens. Mechanical, mineralogical and radiological characterisation of 28-day OPC + FA pastes (bearing up to 30 wt % FA) were characterised to determine their mechanical, mineralogical and radiological properties. The activity concentrations found for 226Ra, 212Pb, 232Th and 40K in hardened, intact 5 cm cubic specimens were also statistically equal to the theoretically calculated values and to the same materials when ground to a powder. These findings consequently validated the new method. The possibility of determining the activity concentrations needed to establish the ACI for cement-based materials on unground samples introduces a new field of radiological research on actual cement, mortar and concrete materials. [ABSTRACT FROM AUTHOR]

Modification of a cement matrix using additives and admixtures has been a common practice for many years. The use of some mineral additives as substitutes for the cement, e.g., the siliceous fly ashes (FAs), has a positive effect on reducing the energy used in cement production. On the other hand, such activities may have negative effects due to the lowering of strength parameters of composites in early stages of curing. In order to solve this problem, over the last few years, thanks to the patented "seedings" technology, a branch of industry connected with the production of admixtures that accelerate the binding process has developed significantly. Therefore, the paper presents the results of research aimed at analyzing the parameters of FA cement matrix with the nanoadmixture containing the nanometric C-S-H seeds (nanoadmixture (NA)). By using the modern NA, an attempt was made to neutralize the negative influence of the used industrial waste on the structure of the cement matrix in the early stages of its curing. The paper presents the results of strength tests for the FA cement pastes modified by NA in seven test periods, i.e., after 8, 12, 24 and 72 h, and 7, 14 and 28 days. Additionally, hydration heat tests were carried out on the analyzed material in the first 24 hours of curing. [ABSTRACT FROM AUTHOR]

Geopolymers are ecologically-friendly inorganic materials which can be produced at low temperatures from industrial wastes such as fly ash, blast furnace slags or mining residues. Although to date their principal applications have been seen as alternatives to Portland cement building materials, their properties make them suitable for a number of more advanced applications, including as photocatalytic nanocomposites for removal of hazardous pollutants from waste water or the atmosphere. For this purpose, they can be combined with photocatalytic moieties such as metal oxides with suitable bandgaps to couple with UV or visible radiation, or with carbon nanotubes or graphene. In these composites the geopolymers act as supports for the photoactive components, but geopolymers formed from wastes containing oxides such as Fe2O3 show intrinsic photoactive behaviour. This review discusses the structure and formation chemistry of geopolymers and the principles required for their utilisation as photocatalysts. The literature on existing photocatalytic geopolymers is reviewed, suggesting that these materials have a promising potential as inexpensive, efficient and ecologically-friendly candidates for the remediation of toxic environmental pollutants and would repay further development. [ABSTRACT FROM AUTHOR]