Search

Alleima 3R60 (TM) is an AISI 316/316 L type of stainless steel. This alloy shows extra-long creep lives. At 700 degrees C with an applied stress of 45 MPa, the specimen broke first after 240 131 hours, a 140% longer creep life than the predicted. The reasons have been studied using SEM/EDS, EBSD, ECCI and TEM. Two unexpected phenomena have been observed. One is the presence of homogeneously dispersed small Mo2Fe4CrSi(Ni-0.5)f063type of precipitates in the matrix. According to the thermodynamic calculation, this phase should not form in this alloy at 700 degrees C. The other is the fine grains formed in the matrix during the creep-testing at 700 degrees C for such an extra-long time. It is believed that both small precipitates and fine grain size contribute to this extra-long creep life of the steel. With the microstructural study and thermodynamic simulation, the mechanisms to form precipitates and fine grains have been discussed.

For heat resistant alloys, long-term structural stability at high temperatures is a critical issue for alloy design and applications. In this paper, the long-term creep behaviours and structural stabilities of six heat resistant high Ni alloys and austenitic stainless steels have been studied. The longest creep rupture life is up to 359 283 hours. High Ni and Cr alloys show a good combination of high creep and oxidation resistances. Precipitation of nano MX particles with a very low growth rate improves long-term creep resistance at high temperatures. Long-term stable multiple nanoprecipitates of MX, Cu-rich, Laves and M23C6 phases can greatly contribute to the creep strength. Low Ni austenitic stainless steels show comparatively low oxidation and creep resistances. It was first found that at 800 & DEG;C, Cr2N could form in the low Ni steel with a long-term crept by the absorption of nitrogen from the air into the matrix.

Fatigue damage and crack initiation behavior has been studied in an austenitic stainless steel using a novel progressive stepwise load increasing method with a cycle step greater than 108 cycles and investigated with a FIB-SEM. Subsurface crack origin with a fine granular area in the matrix was formed. Heterogeneous plastic deformation causes strain localization and grain fragmentation. Localized plasticity exhaustion induces crack initiation. A crack origin is completed once a short crack reaches the stress intensity factor threshold for stage II crack propagation. This study provides a fundamental discussion how damage and crack initiation in matrix occur during very high cycle fatigue.

Ni-based superalloys play a crucial role in various high-temperature applications, where their exceptional mechanical properties and resistance to corrosion are highly desirable. However, their response to low temperatures, especially concerning strain hardening, microstructural evolution, and deformation mechanisms, requires further scrutiny. In this study, we investigate the influence of temperature on the stacking fault energy (SFE) and its implications on deformation twinning in Alloy 625. Uniaxial tensile tests are performed at 298 K, 173 K and 77 K. The study reveals a notable increase in strain hardening at intermediate strain levels, suggesting the activation of a secondary deformation mechanism. To gain deeper insights, crystal plasticity-based simulations using the DAMASK framework are employed, complementing the experimental outcomes. Deformation twins are consistently observed at all temperatures, albeit with a small volume fraction and thickness. The critical strain for twinning decreased with decreasing temperature. Based on the numerous literature studies, experimental and computational observations, the SFE of the material is estimated to be constant over the studied temperature range.

Deformation behaviour in the Nickel-base superalloy 625 has been studied by tensile testing at four temperatures: 295, 223, 173 and 77 K. The microstructure has been investigated using TEM, FIB-SEM, EBSD and ECCI techniques. Deformation in the alloy turns out to be a competitive course of events between at least two deformation mechanisms, namely dislocation slip and deformation twinning. Slip is the predominant deformation mechanism at higher temperatures. While at 77 K, deformation induced twinning gives an extra degree of freedom as one of the main deformation mechanisms, i.e., the material shows a twin induced plasticity, TWIP, behaviour. Ab initio calculations indicate that the influence of cryogenic/sub-zero temperatures on the stacking fault energy of this alloy can be limited and that the formation of deformation twins cannot be determined solely by the stacking fault energy. The results implies that it is the critical strain and strain hardening rate that influences the deformation twinning onset and twinning rate.

This article predicts bending very high cycle fatigue (VHCF) life of three typical nickel-based alloys SM2550, BG2532, and G3 used for completion strings. Fatigue tests were conducted on the three alloys using an ultrasonic fatigue system at a frequency of 20 kHz. The results showed that the fatigue strength ranges of the three alloys were markedly different, reflecting their different sensitivities to fatigue loading. Scanning electron microscope observations revealed numerous fatigue crack origins with internal decohesion in the fatigue source region. To achieve unified prediction of the fatigue life for the three alloys, a prediction model based on deep learning was built with inputs including fatigue initiation quantity, cleavage facet size, and other fatigue fracture characteristics. It was found that single source feature was insufficient to obtain satisfactory prediction accuracy for all alloys, while multifeature coupling integration could significantly improve the prediction precision, enabling reliable prediction of alloy fatigue life. This study provides new insights into bending VHCF life prediction. This article predicts bending VHCF life for three completion strings. Bending VHCF life model utilizing deep wise separable convolution was established. Deep learning can effectively integrate with bending VHCF analyses., Funding Agencies|The 111 Center; Technology Development Project Foundation of PetroChina Southwest Oil and Gas Field CDB Operating Company; The 2023 Open Project of Failure Mechanics and Engineering Disaster Prevention, Key Lab of Sichuan Province [52205182]; National Natural Science Foundation of China [2023NSFSC0916]; Natural Science Foundation of Sichuan Province [20220303-16]; [FMEDP202303]

Fatigue crack initiation in metallic materials during very high cycle fatigue has been characterized by a subsurface crack origin with defect such as an inclusion. In this paper, fatigue damage behavior in an austenitic stainless steel has been studied using a novel progressive stepwise load increasing test method with each cycle step higher than 108 cycles. Subsurface crack origin with a fine granular area has formed in the matrix without defect. This is a new phenomenon. The mechanism has been investigated using Focused Ion Beam crosssectioning and electron channeling contrast imaging techniques. Strain localization, grain fragmentation and local plasticity exhaustion are the main factors that cause fatigue damage and crack initiation in the matrix. This study provides a fundamental understanding how material damage and crack initiation occur in material matrix during very high cycle fatigue.

The influence of nitrogen on the mechanical properties of two high Ni containing advanced austenitic stainless steels with low stacking fault energies is investigated. The results show that increase of nitrogen content greatly increases both strength and elongation of the steel at the same time. At the cryogenic temperature, the steels show a twin induced plasticity behavior. Ab initio calculations indicate that the increase of nitrogen slightly increases the stacking fault energy and consequently the critical shear stress for twin initiation in the steel. However, addition of nitrogen significantly increases the flow stress. This leads to a smaller critical strain for twin initiation and promotes deformation twinning in the high nitrogen steel. This is confirmed by the microstructure investigation. Deformation in steels is a competitive process between slip and twinning. Dislocation slip is dominant at low strain range, but formation of stacking fault and twinning become important in the later stages of deformation. At cryogenic temperature, it is mainly deformation twinning. The influence of nitrogen addition on magnetic property and its effect on deformation twinning are also discussed. The present study increases the understanding for the development of high-performance and low-cost advanced austenitic stainless steels.

The influence of nitrogen on the mechanical properties of two high Ni containing advanced austenitic stainless steels with low stacking fault energies is investigated. The results show that increase of nitrogen content greatly increases both strength and elongation of the steel at the same time. At the cryogenic temperature, the steels show a twin induced plasticity behavior. Ab initio calculations indicate that the increase of nitrogen slightly increases the stacking fault energy and consequently the critical shear stress for twin initiation in the steel. However, addition of nitrogen significantly increases the flow stress. This leads to a smaller critical strain for twin initiation and promotes deformation twinning in the high nitrogen steel. This is confirmed by the microstructure investigation. Deformation in steels is a competitive process between slip and twinning. Dislocation slip is dominant at low strain range, but formation of stacking fault and twinning become important in the later stages of deformation. At cryogenic temperature, it is mainly deformation twinning. The influence of nitrogen addition on magnetic property and its effect on deformation twinning are also discussed. The present study increases the understanding for the development of high-performance and low-cost advanced austenitic stainless steels.

A fine granular area, FGA, is a typical phenomenon observed at the very high cycle fatigue fracture crack origin with a subsurface defect in the material. The FGA has been widely investigated, and different mechanisms have been proposed. In this paper, the formation of FGA in a non-defect matrix of one austenitic steel during very high cycle fatigue was studied using a progressive stepwise load-increasing method and electron scanning microscopy/electron channeling contrast imaging (ECCI) technique. A nano rough surface area or FGA at the fatigue crack origin has been observed in the subsurface matrix without any defect. It is a new phenomenon. A mechanism was proposed using the dislocation plasticity theory. The formation of FGA in a non-defect matrix is a localized plasticity exhausting process by strain localization, grain fragmentation, stress concentration and nano crack initiation and propagation along low-angle grain boundaries.

A fine granular area, FGA, is a typical phenomenon observed at the very high cycle fatigue fracture crack origin with a subsurface defect in the material. The FGA has been widely investigated, and different mechanisms have been proposed. In this paper, the formation of FGA in a non-defect matrix of one austenitic steel during very high cycle fatigue was studied using a progressive stepwise load-increasing method and electron scanning microscopy/electron channeling contrast imaging (ECCI) technique. A nano rough surface area or FGA at the fatigue crack origin has been observed in the subsurface matrix without any defect. It is a new phenomenon. A mechanism was proposed using the dislocation plasticity theory. The formation of FGA in a non-defect matrix is a localized plasticity exhausting process by strain localization, grain fragmentation, stress concentration and nano crack initiation and propagation along low-angle grain boundaries.

A fine granular area, FGA, is a typical phenomenon observed at the very high cycle fatigue fracture crack origin with a subsurface defect in the material. The FGA has been widely investigated, and different mechanisms have been proposed. In this paper, the formation of FGA in a non-defect matrix of one austenitic steel during very high cycle fatigue was studied using a progressive stepwise load-increasing method and electron scanning microscopy/electron channeling contrast imaging (ECCI) technique. A nano rough surface area or FGA at the fatigue crack origin has been observed in the subsurface matrix without any defect. It is a new phenomenon. A mechanism was proposed using the dislocation plasticity theory. The formation of FGA in a non-defect matrix is a localized plasticity exhausting process by strain localization, grain fragmentation, stress concentration and nano crack initiation and propagation along low-angle grain boundaries.

The influence of nitrogen on the mechanical properties of two high Ni containing advanced austenitic stainless steels with low stacking fault energies is investigated. The results show that increase of nitrogen content greatly increases both strength and elongation of the steel at the same time. At the cryogenic temperature, the steels show a twin induced plasticity behavior. Ab initio calculations indicate that the increase of nitrogen slightly increases the stacking fault energy and consequently the critical shear stress for twin initiation in the steel. However, addition of nitrogen significantly increases the flow stress. This leads to a smaller critical strain for twin initiation and promotes deformation twinning in the high nitrogen steel. This is confirmed by the microstructure investigation. Deformation in steels is a competitive process between slip and twinning. Dislocation slip is dominant at low strain range, but formation of stacking fault and twinning become important in the later stages of deformation. At cryogenic temperature, it is mainly deformation twinning. The influence of nitrogen addition on magnetic property and its effect on deformation twinning are also discussed. The present study increases the understanding for the development of high-performance and low-cost advanced austenitic stainless steels.

Multi-component alloys have received increasing interest for functional applications in recent years. Here, we explore the magnetocaloric response for Al-Cr-Mn-Co medium-entropy alloys by integrated theoretical and experimental methods. Under the guidance of thermodynamic and ab initio calculations, a dual-phase system with large magnetic moment, i.e., Al50Cr19Mn19Co12, is synthesized, and the structural and magnetocaloric properties are confirmed via characterization. The obtained results indicate that the selected alloy exhibits a co-continuous mixture of a disordered body-centered cubic and an ordered B2 phase. The ab initio and Monte Carlo calculations indicate that the presence of the ordered B2 phase is responsible for the substantial magnetocaloric effect. The magnetization measurements demonstrated that this alloy undergoes a second-order magnetic transition with the Curie temperature of similar to 300 K. The magnetocaloric properties are examined using magnetic entropy change, refrigeration capacity, and adiabatic temperature change. The property-directed strategy explored here is intended to contribute to the study of potential multi-component alloys in magnetocaloric applications., Funding Agencies|Swedish Foundation for Strategic Research; Swedish Research Council [2018-05973]; Swedens Innovation Agency (VINNOVA) [2019-05111]; Swedish Energy Agency; Hungarian Scientific Research Fund (OTKA) [128229]; Carl Tryggers Foundation [19:325, 20:474]; Zhejiang Provincial Natural Science Foundation of China [LY23E010003]

In the very high cycle fatigue regime, fatigue crack initiation in high-strength steels is usually correlated to a subsurface inclusion with a fine granular area (FGA). Localized stress-strain concentration at the subsurface inclusion is a critical factor. Fatigue crack initiation with an FGA in the bulk matrix without any defect has rarely been reported. In this paper, a fundamental study on the formation of FGAs in the bulk matrix of an austenitic stainless steel has been carried out using a progressive stepwise load-increasing test with a cycle step of about 108 cycles. FGA formation in the subsurface bulk matrix has been observed. The micro structural damage in the fatigue-tested specimens has been studied using the electron channeling contrast imaging electron microscopy technique. Strain localization and grain fragmentation are the main processes for the formation of FGAs. Local plasticity exhaustion leads to crack initiation due to local stress concentrations. This method can also be used to predict the fatigue damage process, especially the damage rate in individual specimens.

A fine granular area, FGA, is a typical phenomenon observed at the very high cycle fatigue fracture crack origin with a subsurface defect in the material. The FGA has been widely investigated, and different mechanisms have been proposed. In this paper, the formation of FGA in a non-defect matrix of one austenitic steel during very high cycle fatigue was studied using a progressive stepwise load-increasing method and electron scanning microscopy/electron channeling contrast imaging (ECCI) technique. A nano rough surface area or FGA at the fatigue crack origin has been observed in the subsurface matrix without any defect. It is a new phenomenon. A mechanism was proposed using the dislocation plasticity theory. The formation of FGA in a non-defect matrix is a localized plasticity exhausting process by strain localization, grain fragmentation, stress concentration and nano crack initiation and propagation along low-angle grain boundaries.

A fine granular area, FGA, is a typical phenomenon observed at the very high cycle fatigue fracture crack origin with a subsurface defect in the material. The FGA has been widely investigated, and different mechanisms have been proposed. In this paper, the formation of FGA in a non-defect matrix of one austenitic steel during very high cycle fatigue was studied using a progressive stepwise load-increasing method and electron scanning microscopy/electron channeling contrast imaging (ECCI) technique. A nano rough surface area or FGA at the fatigue crack origin has been observed in the subsurface matrix without any defect. It is a new phenomenon. A mechanism was proposed using the dislocation plasticity theory. The formation of FGA in a non-defect matrix is a localized plasticity exhausting process by strain localization, grain fragmentation, stress concentration and nano crack initiation and propagation along low-angle grain boundaries.

The influence of nitrogen on the mechanical properties of two high Ni containing advanced austenitic stainless steels with low stacking fault energies is investigated. The results show that increase of nitrogen content greatly increases both strength and elongation of the steel at the same time. At the cryogenic temperature, the steels show a twin induced plasticity behavior. Ab initio calculations indicate that the increase of nitrogen slightly increases the stacking fault energy and consequently the critical shear stress for twin initiation in the steel. However, addition of nitrogen significantly increases the flow stress. This leads to a smaller critical strain for twin initiation and promotes deformation twinning in the high nitrogen steel. This is confirmed by the microstructure investigation. Deformation in steels is a competitive process between slip and twinning. Dislocation slip is dominant at low strain range, but formation of stacking fault and twinning become important in the later stages of deformation. At cryogenic temperature, it is mainly deformation twinning. The influence of nitrogen addition on magnetic property and its effect on deformation twinning are also discussed. The present study increases the understanding for the development of high-performance and low-cost advanced austenitic stainless steels.

The influence of nitrogen on the mechanical properties of two high Ni containing advanced austenitic stainless steels with low stacking fault energies is investigated. The results show that increase of nitrogen content greatly increases both strength and elongation of the steel at the same time. At the cryogenic temperature, the steels show a twin induced plasticity behavior. Ab initio calculations indicate that the increase of nitrogen slightly increases the stacking fault energy and consequently the critical shear stress for twin initiation in the steel. However, addition of nitrogen significantly increases the flow stress. This leads to a smaller critical strain for twin initiation and promotes deformation twinning in the high nitrogen steel. This is confirmed by the microstructure investigation. Deformation in steels is a competitive process between slip and twinning. Dislocation slip is dominant at low strain range, but formation of stacking fault and twinning become important in the later stages of deformation. At cryogenic temperature, it is mainly deformation twinning. The influence of nitrogen addition on magnetic property and its effect on deformation twinning are also discussed. The present study increases the understanding for the development of high-performance and low-cost advanced austenitic stainless steels.

Rising global energy consumption and the increase in emissions of greenhouse gases (e.g. CO2) causing global warming, make need for more sustainable power generation. This could be accomplished by increasing the efficiency of the biomass-fired power plants, which is achieved by increasing the temperature and pressure. In addition, flexible generation of power is critical if only renewable power generation is to be achieved and this will increase the number of start-and stop cycles. Cyclic condition in a long-term high temperature environment is an operation process that such materials must withstand, in order to satisfy the needs for future power generation. Commonly austenitic stainless steel are used for critical components of power plants. Because of future change in operating conditions, further investigations are needed to verify that the demands on safety for cyclic long-term usage is fulfilled. This work includes investigation of two commercial austenitic steels: Esshete 1250 and Sanicro 25. The materials were exposed to thermomechanical fatigue (TMF) in strain control under In-Phase and Out-of-Phase conditions and main testing temperature ranges of 100-650°C and 100-800°C respectively. Some of the specimens were pre-aged to simulate prolonged service condition. Mechanical test data were obtained and analysed in order to define the TMF performance of the investigated alloys. The differences in performance were discussed in relation to mechanical and microstructural characterization., Funding Agencies|Alleima AB; Swedish Energy Agency through the Research Consortium of Materials Technology for Thermal Energy Processes [39297-1, 39297-2, 39297-3]

This work investigates two austenitic stainless steels, Sanicro 25 which is a candidate for high temperature heavy section components of future power plants and Esshete 1250 which is used as a reference material. The alloys were subjected to out-of-phase (OP) thermomechanical fatigue (TMF) testing under strain-control in the temperature range of 100 ∘C to 650 ∘C. Both unaged and aged (650 ∘C, 3000 h) TMF specimens were tested to simulate service degradation resulting from long-term usage. The scanning electron microscopy methods electron backscatter diffraction (EBSD) and energy dispersive spectroscopy (EDS) were used to analyse and discuss active failure and deformation mechanisms. The Sanicro 25 results show that the aged specimens suffered increased plastic straining and shorter TMF-life compared to the unaged specimens. The difference in TMF-life of the two test conditions was attributed to an accelerated microstructural evolution that provided decreased the effectiveness for impeding dislocation motion. Ageing did not affect the OP-TMF life of the reference material, Esshete 1250. However, the structural stability and its resistance for cyclic deformation was greatly reduced due to coarsening and cracking of the strengthening niobium carbide precipitates. Sanicro 25 showed the higher structural stability during OP-TMF testing compare with the reference material., Funding: AB Sandvik Materials Technology in Sweden; Swedish Energy Agency through the Research Consortium of Materials Technology for Thermal Energy Processes [KME-801]

Microstructural evolution related to the mechanical response from isothermal dwell-fatigue testing at 700 °C of two austenitic steels, Esshete 1250 and Sanicro 25, is reported. Coherent Cu-precipitates and incoherent Nb-carbides were found to impede dislocation motion, increase hardening and improving the high temperature properties of Sanicro 25. Sparsely placed intergranular Cr- and Nb-carbides made Esshete 1250 susceptible to creep damage and intergranular crack propagation, mainly from interaction of the carbides and fatigue induced slip bands. Dynamic recrystallization of the plastic zone at the crack tip appeared to affect crack propagation of Sanicro 25 by providing an energetically privileged path., Funding agencies: AB Sandvik Materials Technology in Sweden; Swedish Energy Agency through the Research Consortium of Materials Technology for Thermal Energy Processes [KME-701]

Microstructural evolution related to the mechanical response from isothermal dwell-fatigue testing at 700 °C of two austenitic steels, Esshete 1250 and Sanicro 25, is reported. Coherent Cu-precipitates and incoherent Nb-carbides were found to impede dislocation motion, increase hardening and improving the high temperature properties of Sanicro 25. Sparsely placed intergranular Cr- and Nb-carbides made Esshete 1250 susceptible to creep damage and intergranular crack propagation, mainly from interaction of the carbides and fatigue induced slip bands. Dynamic recrystallization of the plastic zone at the crack tip appeared to affect crack propagation of Sanicro 25 by providing an energetically privileged path., Funding agencies: AB Sandvik Materials Technology in Sweden; Swedish Energy Agency through the Research Consortium of Materials Technology for Thermal Energy Processes [KME-701]

Microstructural evolution related to the mechanical response from isothermal dwell-fatigue testing at 700 °C of two austenitic steels, Esshete 1250 and Sanicro 25, is reported. Coherent Cu-precipitates and incoherent Nb-carbides were found to impede dislocation motion, increase hardening and improving the high temperature properties of Sanicro 25. Sparsely placed intergranular Cr- and Nb-carbides made Esshete 1250 susceptible to creep damage and intergranular crack propagation, mainly from interaction of the carbides and fatigue induced slip bands. Dynamic recrystallization of the plastic zone at the crack tip appeared to affect crack propagation of Sanicro 25 by providing an energetically privileged path., Funding agencies: AB Sandvik Materials Technology in Sweden; Swedish Energy Agency through the Research Consortium of Materials Technology for Thermal Energy Processes [KME-701]

Microstructural evolution related to the mechanical response from isothermal dwell-fatigue testing at 700 °C of two austenitic steels, Esshete 1250 and Sanicro 25, is reported. Coherent Cu-precipitates and incoherent Nb-carbides were found to impede dislocation motion, increase hardening and improving the high temperature properties of Sanicro 25. Sparsely placed intergranular Cr- and Nb-carbides made Esshete 1250 susceptible to creep damage and intergranular crack propagation, mainly from interaction of the carbides and fatigue induced slip bands. Dynamic recrystallization of the plastic zone at the crack tip appeared to affect crack propagation of Sanicro 25 by providing an energetically privileged path., Funding agencies: AB Sandvik Materials Technology in Sweden; Swedish Energy Agency through the Research Consortium of Materials Technology for Thermal Energy Processes [KME-701]

High-entropy functional materials are of great interest in materials science and engineering community. In this work, ab initio electronic structure calculations of the phase stability and magnetic transition temperature of AlxCr0.25MnFeCo0.25−yNiy (x = 0–0.5, y = 0–0.25) alloys were performed to screen for compositions showing promising magnetocaloric properties in the vicinity of room temperature. The selected Al0.44Cr0.25MnFeCo0.05Ni0.2 alloy was synthesized via a rapid solidification technique and systematically characterized with respect to its structural and magnetocaloric properties. The results indicate that this alloy possesses a homogeneous microstructure based on an underlying body-centered cubic lattice and has a Curie temperature of ∼340 K. The temperature dependence of the adiabatic temperature change was evaluated using both direct and indirect methods. The ab initio-assisted design of 3d-metal-based high-entropy alloys, explored here, is intended to contribute to the development of magnetic refrigerators for room-temperature applications., Funding: Swedish Foundation for Strategic ResearchSwedish Foundation for Strategic Research; Swedish Research CouncilSwedish Research CouncilEuropean Commission; Swedens Innovation Agency (VINNOVA)Vinnova [2019-05111]; Carl Tryggers Foundation; Swedish Energy Agency, ST and UPP; Hungarian Scientific Research Fund (OTKA)Orszagos Tudomanyos Kutatasi Alapprogramok (OTKA) [128229]

We investigate the AlxCr0.2MnFe0.5Co0.3Ni0.5 (0.3 <= x <= 0.7) high-entropy alloys by combining experimental and theoretical techniques. X-ray diffraction and magnetization measurements indicate that Al alters the crystal structure and the entropy change upon magnetization-demagnetization while keeping the Curie temperature almost unchanged. First-principles calculations of the vibrational, magnetic, electronic, and configurational entropies show that the leading entropy change is due to the magnetic and vibrational degrees of freedom. The presence of the body-centered-cubic phase, showing a sizable elastic softening upon magnetic transition, brings about the substantial magnetocaloric effect in this family of alloys., Funding: Swedish Foundation for Strategic ResearchSwedish Foundation for Strategic Research; Swedish Research CouncilSwedish Research CouncilEuropean Commission; Swedens Innovation Agency (VINNOVA)Vinnova [2019-05111]; Carl Tryggers Foundation; Swedish Energy Agency, STandUPPSwedish Energy Agency; Hungarian Scientific Research Fund (OTKA)Orszagos Tudomanyos Kutatasi Alapprogramok (OTKA) [128229]

High entropy alloys (HEAs) based on transition metals display rich magnetic characteristics, however attempts on their application in energy efficient technologies remain scarce. Here, we explore the magnetocaloric application for a series of MnxCr0.3Fe0.5Co0.2Ni0.5Al0.3 (0.8 < x < 1.1) HEAs by integrated theoretical and experimental methods. Both theory and experiment indicate the designed HEAs have the Curie temperature close to room temperature and is tunable with Mn concentration. A non-monotonic evolution is observed for both the entropy change and the relative cooling power with changing Mn concentration. The underlying atomic mechanism is found to primarily emerge from the complex impact of Mn on magnetism. Advanced magnetocaloric properties can be achieved by tuning Mn concentration in combination with controlling structural phase stability for the designed HEAs. (C) 2021 Published by Elsevier Ltd on behalf of The editorial office of Journal of Materials Science & Technology., Funding Agencies|Swedish Research CouncilSwedish Research CouncilEuropean Commission [2015-5335, 2017-06474]; Swedish Foundation for Strategic ResearchSwedish Foundation for Strategic Research [S14-0038, SM16-0036]; Swedish Foundation for International Cooperation in Research and Higher Education [CH2015-6292]; Swedish Energy AgencySwedish Energy Agency; Hungarian Scientific Research FundOrszagos Tudomanyos Kutatasi Alapprogramok (OTKA) [OTKA 128229]; Carl Tryggers Foundation; Swedish Energy Agency (Energimyndigheten)Swedish Energy Agency; ST; UPP; eSSENCE

Microstructural evolution related to the mechanical response from isothermal dwell-fatigue testing at 700 °C of two austenitic steels, Esshete 1250 and Sanicro 25, is reported. Coherent Cu-precipitates and incoherent Nb-carbides were found to impede dislocation motion, increase hardening and improving the high temperature properties of Sanicro 25. Sparsely placed intergranular Cr- and Nb-carbides made Esshete 1250 susceptible to creep damage and intergranular crack propagation, mainly from interaction of the carbides and fatigue induced slip bands. Dynamic recrystallization of the plastic zone at the crack tip appeared to affect crack propagation of Sanicro 25 by providing an energetically privileged path., Funding agencies: AB Sandvik Materials Technology in Sweden; Swedish Energy Agency through the Research Consortium of Materials Technology for Thermal Energy Processes [KME-701]

We report a chemically disordered solid solution, Al0.6Cr0.2MnFe0.5Co0.3Ni0.5, based on a body-centered cubic underlying lattice with the measured Curie temperature of ∼380 K. First-principles alloy theory is employed to investigate the temperature-dependent free energy, elastic constants, and coefficient of thermal expansion at the ferromagnetic and paramagnetic states. Theory and experiment are found to strengthen each other, and the results indicate that the magnetic state has a strong impact on the thermo-elastic properties of the considered alloy. The present advance in the thermo-magneto-elasticity enhances the understanding required for controlling the magnetic and mechanical response of multi-component systems., Funding agencies: Swedish Foundation for Strategic ResearchSwedish Foundation for Strategic Research; Swedish Research CouncilSwedish Research Council; Swedens Innovation Agency (VINNOVA)Vinnova [2019-05111]; Carl Tryggers Foundation; Swedish Energy AgencySwedish Energy Ag

Using ab initio alloy theory, we calculate the impact of Ni on the stacking fault energy in austenitic stainless steel as a function of temperature. We show that the influence of Ni strongly couples with temperature. While a positive effect on the stacking fault energy is obtained at ambient temperature, the opposite negative effect is disclosed at elevated temperatures. An important rationale behind is demonstrated to be the variation of magneto-volume coupling induced by Ni alloying. The alloy influence on the finite temperature evolution of Ni impact is evaluated for elements Cr, Mo and N. (C) 2019 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved., Funding Agencies|Swedish Research CouncilSwedish Research Council [2015-5335, 2017-06474]; Swedish Foundation for Strategic ResearchSwedish Foundation for Strategic Research [S14-0038, SM16-0036]; Swedish Foundation for International Cooperation in Research and Higher Education [CH2015-6292]; Hungarian Scientific Research FundOrszagos Tudomanyos Kutatasi Alapprogramok (OTKA) [OTKA 128229]; Carl Tryggers Foundation

The increasing demands for efficiency and flexibility result in more severe operating conditions for the materials used in critical components of biomass power plants. These operating conditions involve higher temperature ranges, more pronounced environmental effects and cyclic operations. Austenitic stainless steels have shown to possess promising high temperature properties which makes them suitable as candidates for critical components in biomass power plant. However, their behaviour under such conditions is not yet fully understood. This work investigates three commercial austenitic alloys: Esshete 1250, Sanicro 25 and Sanicro 31HT. The alloys were subjected to in-phase (IP) thermomechanical fatigue (TMF) testing under strain-control in the temperature range of 100–800 °C. Both virgin and pre-aged TMF specimens were tested in order to simulate service degradation resulting from long-term usage. The results show that the pre-aged specimens suffered shorter TMF-life compared to the virgin specimens. The scanning electron microscopy methods electron backscatter diffraction (EBSD) and energy dispersive spectroscopy (EDS) were used to analyse and discuss active failure and deformation mechanisms. The difference in TMF-life produced by the two testing conditions was attributed to an embrittling effect by precipitation, reduced creep properties and oxidation assisted cracking., Funding agencies: AB Sandvik Materials Technology in Sweden; Swedish Energy Agency through the Research Consortium of Materials Technology for Thermal Energy Processes [KME-701]

The increasing demands for efficiency and flexibility result in more severe operating conditions for the materials used in critical components of biomass power plants. These operating conditions involve higher temperature ranges, more pronounced environmental effects and cyclic operations. Austenitic stainless steels have shown to possess promising high temperature properties which makes them suitable as candidates for critical components in biomass power plant. However, their behaviour under such conditions is not yet fully understood. This work investigates three commercial austenitic alloys: Esshete 1250, Sanicro 25 and Sanicro 31HT. The alloys were subjected to in-phase (IP) thermomechanical fatigue (TMF) testing under strain-control in the temperature range of 100–800 °C. Both virgin and pre-aged TMF specimens were tested in order to simulate service degradation resulting from long-term usage. The results show that the pre-aged specimens suffered shorter TMF-life compared to the virgin specimens. The scanning electron microscopy methods electron backscatter diffraction (EBSD) and energy dispersive spectroscopy (EDS) were used to analyse and discuss active failure and deformation mechanisms. The difference in TMF-life produced by the two testing conditions was attributed to an embrittling effect by precipitation, reduced creep properties and oxidation assisted cracking., Funding agencies: AB Sandvik Materials Technology in Sweden; Swedish Energy Agency through the Research Consortium of Materials Technology for Thermal Energy Processes [KME-701]

The increasing demands for efficiency and flexibility result in more severe operating conditions for the materials used in critical components of biomass power plants. These operating conditions involve higher temperature ranges, more pronounced environmental effects and cyclic operations. Austenitic stainless steels have shown to possess promising high temperature properties which makes them suitable as candidates for critical components in biomass power plant. However, their behaviour under such conditions is not yet fully understood. This work investigates three commercial austenitic alloys: Esshete 1250, Sanicro 25 and Sanicro 31HT. The alloys were subjected to in-phase (IP) thermomechanical fatigue (TMF) testing under strain-control in the temperature range of 100–800 °C. Both virgin and pre-aged TMF specimens were tested in order to simulate service degradation resulting from long-term usage. The results show that the pre-aged specimens suffered shorter TMF-life compared to the virgin specimens. The scanning electron microscopy methods electron backscatter diffraction (EBSD) and energy dispersive spectroscopy (EDS) were used to analyse and discuss active failure and deformation mechanisms. The difference in TMF-life produced by the two testing conditions was attributed to an embrittling effect by precipitation, reduced creep properties and oxidation assisted cracking., Funding agencies: AB Sandvik Materials Technology in Sweden; Swedish Energy Agency through the Research Consortium of Materials Technology for Thermal Energy Processes [KME-701]

The increasing demands for efficiency and flexibility result in more severe operating conditions for the materials used in critical components of biomass power plants. These operating conditions involve higher temperature ranges, more pronounced environmental effects and cyclic operations. Austenitic stainless steels have shown to possess promising high temperature properties which makes them suitable as candidates for critical components in biomass power plant. However, their behaviour under such conditions is not yet fully understood. This work investigates three commercial austenitic alloys: Esshete 1250, Sanicro 25 and Sanicro 31HT. The alloys were subjected to in-phase (IP) thermomechanical fatigue (TMF) testing under strain-control in the temperature range of 100–800 °C. Both virgin and pre-aged TMF specimens were tested in order to simulate service degradation resulting from long-term usage. The results show that the pre-aged specimens suffered shorter TMF-life compared to the virgin specimens. The scanning electron microscopy methods electron backscatter diffraction (EBSD) and energy dispersive spectroscopy (EDS) were used to analyse and discuss active failure and deformation mechanisms. The difference in TMF-life produced by the two testing conditions was attributed to an embrittling effect by precipitation, reduced creep properties and oxidation assisted cracking., Funding agencies: AB Sandvik Materials Technology in Sweden; Swedish Energy Agency through the Research Consortium of Materials Technology for Thermal Energy Processes [KME-701]

The mechanisms for the formation of Laves phase located at grain boundaries and in grain interiors in Sanicro 25 steel after creep-rupture test at 700 degrees C and 150/180MPa for 9862/5665h were studied, respectively. Scanning electron microscopy, transmission electron microscopy, energy-dispersive X-ray spectrometer, and multi-phase separation technology analysis reveals that Laves phase particles nucleated adjacently either to Si-enriched spots present in the bulky M23C6 carbides or to the grain boundary areas rich in Si, which made the bulky M23C6 carbides gradually divide into small pieces and eventually resulted in the formation of a refined mixture of M23C6 and Laves phase at grain boundaries. Laves phase particles formed independently in austenitic matrix and also dependently at interfaces between austenitic matrix and Z phase in grain interiors. The size and morphology of Laves phase formed at grain boundaries (in M23C6 carbides) and in grain interiors (austenitic matrix) are different. It is hoped that the presented findings will be helpful to understand the Laves phase formation and the grain boundary precipitate refinement correlated with good mechanical properties of this class of austenitic steels/alloys.

The increasing demands for efficiency and flexibility result in more severe operating conditions for the materials used in critical components of biomass power plants. These operating conditions involve higher temperature ranges, more pronounced environmental effects and cyclic operations. Austenitic stainless steels have shown to possess promising high temperature properties which makes them suitable as candidates for critical components in biomass power plant. However, their behaviour under such conditions is not yet fully understood. This work investigates three commercial austenitic alloys: Esshete 1250, Sanicro 25 and Sanicro 31HT. The alloys were subjected to in-phase (IP) thermomechanical fatigue (TMF) testing under strain-control in the temperature range of 100–800 °C. Both virgin and pre-aged TMF specimens were tested in order to simulate service degradation resulting from long-term usage. The results show that the pre-aged specimens suffered shorter TMF-life compared to the virgin specimens. The scanning electron microscopy methods electron backscatter diffraction (EBSD) and energy dispersive spectroscopy (EDS) were used to analyse and discuss active failure and deformation mechanisms. The difference in TMF-life produced by the two testing conditions was attributed to an embrittling effect by precipitation, reduced creep properties and oxidation assisted cracking., Funding agencies: AB Sandvik Materials Technology in Sweden; Swedish Energy Agency through the Research Consortium of Materials Technology for Thermal Energy Processes [KME-701]

This work includes an investigation of two commercial austenitic steels: UNS S21500 (Esshete 1250) and UNS S31035 (Sandvik Sanicro (TM) 25). The materials were exposed to isothermal strain controlled fatigue with load controlled dwell time at maximum strain. The testing temperature used was 700 degrees C and the test cycles were performed in tension. Mechanical test data were obtained and analysed in order to define creep-fatigue damage diagrams at failure for the investigated austenitic alloys. During the given conditions, Sanicro 25 showed superior creep-fatigue life, suffered less amount of creep elongation for the same amount of strain amplitude and dwell times compared to Esshete 1250. Both alloys showed creep-fatigue interaction damage for specific test configurations., Funding Agencies|AB Sandvik Materials Technology in Sweden; Swedish Energy Agency through Research Consortium of Materials Technology for Thermal Energy Processes [KME-701]; AFM Strategic Faculty Grant SFO-MAT-LiU at Linkoping University [2009-00971]

Deformation twinning behaviors have been studied in high Ni alloys, Alloy 28 or Sanicro 28 and Alloy 625 at RT and at cryogenic temperature. The microstructures were evaluated using SEM-EBSD. Some constitutive approach has also been used in the discussion on the deformation twinning in high Ni-alloys. The results show that deformation twinning can occur in high Ni alloys depending on the chemical composition, strain range and stress conditions. TWIP can occur in the Ni based superalloy Alloy 625 at cryogenic temperature, which increases both strength and ductility. This is the first report of this phenomena for this alloy. Deformation twinning in high Ni alloys occurs heterogeneously in the material, depending on crystallographic parameters such as grain orientation and Schmid factor. Formation of deformation twins can lead to high texture in the material, which will contribute to the increase of strength. The mechanisms for the formation of deformation twins in high Ni alloys have been discussed.

Future advanced ultra-supercritical power plant will be run at higher temperature and pressure. New materials will be used to meet the requirements. However, the structure integrity of these materials needs to be evaluated. Sanicro 25 is a newly developed advanced austenitic heat resistant stainless steel with the aim to be used in future 700 degrees C or 650 degrees C power plants to replace part of Ni based alloys. This paper provides an overview on the fracture and damage behavior in this material during LCF, TMF and CF. The cyclic hardening and fatigue life during LCF, TMF and CF will be discussed. The influence of prolonged service degradation has been analyzed by the use of pre-aged material for TMF and CF loading conditions. (C) 2018 The Authors. Published by Elsevier B.V. Peer-review under responsibility of the ECF22 organizers., Funding Agencies|AB Sandvik Materials Technology in Sweden; Swedish Energy Agency through the Research Consortium of Materials Technology for Thermal Energy Processes [KME-701]; AFM Strategic Faculty Grant SFO-MAT-LiU at Linkoping University [2009-00971]; IPMinfra [LM2015069]; IPMinfra through project CEITEC 2020 of MEYS, Czech Rep [LQ1601]

This work includes an investigation of two commercial austenitic steels: UNS S21500 (Esshete 1250) and UNS S31035 (Sandvik Sanicro (TM) 25). The materials were exposed to isothermal strain controlled fatigue with load controlled dwell time at maximum strain. The testing temperature used was 700 degrees C and the test cycles were performed in tension. Mechanical test data were obtained and analysed in order to define creep-fatigue damage diagrams at failure for the investigated austenitic alloys. During the given conditions, Sanicro 25 showed superior creep-fatigue life, suffered less amount of creep elongation for the same amount of strain amplitude and dwell times compared to Esshete 1250. Both alloys showed creep-fatigue interaction damage for specific test configurations., Funding Agencies|AB Sandvik Materials Technology in Sweden; Swedish Energy Agency through Research Consortium of Materials Technology for Thermal Energy Processes [KME-701]; AFM Strategic Faculty Grant SFO-MAT-LiU at Linkoping University [2009-00971]

Sanicro 25 material is approved for use in pressure vessels and boilers according AMSE code case 2752, 2753 and VdTuN blatt 555. It shows good resistance to steam oxidation and flue gas corrosion, and has higher creep rupture strength than any other austenitic stainless steels available today. It is a candidate material for superheater and reheaters, enabling higher steam parameters of up to about 650 degrees C steam (ie about max 700 degrees C metal) without the need for expensive nickel based alloys. The effect of cold-forming on time and temperature-dependent deformation and strength behavior has been examined in a comprehensive study. The objective was to determine the maximum allowable degree of cold-forming to be used without additional heat treatment. The findings of these investigations indicate that the maximum allowed cold deformation could be possible to increase from todays maximum 20 % (VdTuV 555), 15 % (540-675 degrees C) and 10 % (higher than 675 degrees C) respectively (ASME 2011a Sect I PG19). A solution annealing after the cold bending will recover creep ductility but will also at the same time increase manufacturing costs. Higher allowed degree of cold-forming without the need for post bend heat treatments, would allow for more narrow bending radii and thereby a more compact construction that would result in a significant decrease in production costs. This paper presents the findings in the mentioned study and is to be a background for possible coming discussions with involved entities on a revision of the max allowed deformation of this material without the need for solution annealing.

Highly alloyed austenitic stainless steels are promising candidates to replace more expansive nickel-based alloys within the energy-producing industry. The present study investigates the deformation mechanisms by microstructural characterisation, mechanical properties and stress-strain response of three commercial austenitic stainless steels and two commercial nickel-based alloys using uniaxial tensile tests at elevated temperatures from 400 C up to 700 C. The materials showed different influence of temperature on ductility, where the ductility at elevated temperatures increased with increasing nickel and solid solution hardening element content. The investigated materials showed planar dislocation driven deformation at elevated temperature. Scanning electron microscopy showed that deformation twins were an active deformation mechanism in austenitic stainless steels during tensile deformation at elevated temperatures up to 700 C., Previous status of this publication was manuscriptFunding agencies: AB Sandvik Materials Technology in Sweden; Swedish National Energy Administration through the Research Consortium of Materials Technology for Thermal Energy Processes [KME-701]; AFM Strategic Faculty Grant SFO-MAT-LiU at Linkoping University [2009-00971]

Highly alloyed austenitic stainless steels are promising candidates to replace more expansive nickel-based alloys within the energy-producing industry. The present study investigates the deformation mechanisms by microstructural characterisation, mechanical properties and stress-strain response of three commercial austenitic stainless steels and two commercial nickel-based alloys using uniaxial tensile tests at elevated temperatures from 400 C up to 700 C. The materials showed different influence of temperature on ductility, where the ductility at elevated temperatures increased with increasing nickel and solid solution hardening element content. The investigated materials showed planar dislocation driven deformation at elevated temperature. Scanning electron microscopy showed that deformation twins were an active deformation mechanism in austenitic stainless steels during tensile deformation at elevated temperatures up to 700 C., Previous status of this publication was manuscriptFunding agencies: AB Sandvik Materials Technology in Sweden; Swedish National Energy Administration through the Research Consortium of Materials Technology for Thermal Energy Processes [KME-701]; AFM Strategic Faculty Grant SFO-MAT-LiU at Linkoping University [2009-00971]