57 results on '"Hasegawa, Satoshi"'
Search Results
2. J1030101 Rotordynamic Characteristics of Segmented Seal under Whirling Motion
3. ICONE23-1530 Effect of boiling phenomena on the corrosion of austenitic stainless steel (R-SUS304ULC) in nitric acid solution containing chromium ions
4. C40 Investigation of abrasion phenomenon of micro-drilling for Print Writing Boards containing high hardness fillers
5. 407 Multibody Analysis of Contact Force between Studs and Dimples of a Linear Roller Bearing
6. 1P1-P13 Angle Restriction Problem of Passive Sub-Crawler for Crawler Robot(Search and Rescue Robot and Mechatronics)
7. 1P1-P09 Mechanism for adjusting the tension of having passive variable geometry tracked vehicle(Search and Rescue Robot and Mechatronics)
8. 1P1-P08 Remote Control System of Disaster Response with Passive Sub-Crawler Corresponding Overturn Avoidance(Search and Rescue Robot and Mechatronics)
9. S054025 Effect of pre-shear on shear-hardening of wormlike micelles solutions
10. 2A1-N06 Dynamic Creation of Stricken Information On GIS Utilized GoogleMaps by Applying(Search and Rescue Robot and Mechatronics(1))
11. J051044 Thermodynamic Effect of Cavitation on a Hydrofoil in Liquid Nitrogen
12. 1213 Thermodynamic Effects on Tip Leakage Vortex Cavitation
13. 613 Crack Size Evaluation Procedure Using Potential Drop Method
14. 0802 Visual Observation of Cavitating Inducer in Cryogenic Flow
15. 201 Temperature Measurements in Cryogenic Cavitation Tunnel
16. 1113 Thermodynamic Effects on Cryogenic Cavitation in Nozzle
17. 1721 Introduction of Cryogenic Cavitation Tunnel in JAXA
18. 553 Evaluation of Leakage of Gasket for Flanged Joint under Room TemperatureTokyo Denki University and Elevated Temperature : J-EHOT Test of Non-asbestos fiber compressed Sheet Gaskets
19. 1724 Observation of Prewirl Flow into the Backflow at the Inducer
20. 124 Visualization of Backflow at a Turbopump Inducer under Some Inlet Pressure Conditions
21. 207 Observations of Various Cavitation Patterns in a Four Bladed Inducer
22. 1723 On Direct Visualization of Cavitating Inducer in Cryogenic Flow
23. Shear Effects on the Loop Bridge Ratio of Middle Block Chains in Sphere-Forming ABA Triblock Copolymers Examined by Simple Elongation Measurements
24. 557 Evaluation of Leakage of Gasket for Flanged Joint under Room Temperature and Elevated Temperature : J-EHOT Test of Expanded PTFE Gaskets
25. OS15-2-2 Flow effects on the loop bridge ratio in sphere-forming triblock copolymer
26. 1611 Behavior of Shaft Vibration at the Inception of Synchronous Rotating Cavitation
27. 112 Temperature Measurement Techniques in Cryogenic Inducer Test Facility
28. 113 Influence of Thermodynamic Effect on Shaft Vibration Caused by Rotating Cavitation
29. Influence of Thermodynamic Effect on Synchronous Rotating Cavitation
30. 2438 Investigation of Uneven Cavity Length under the Synchronous Rotating Cavitation
31. Unsteady Pressure Fluctuations in an Inducer
32. 2439 Observation of Shaft Vibration Caused by the Clouds of Cavitation in Backflow Vortices
33. 103 Influence of Thermodynamic Effect on Synchronous Rotating Cavitation
34. 2435 Casing Treatment for Suppression of Cavitation Surge : 2nd report : Observation of Inducer Internal Flow with PIV
35. 2440 Observations of Inlet Flow at Cryogenic Pump
36. 807 Evaluation of Leakage of Gasket for Flanged Joint under Room Temperature and Elevated Temperature : Proposal of J-EHOT Test Procedure
37. Theromdynamic Effect on a Cavitating Inducer in Liquid Nitrogen
38. 1513 Shaft Vibrations of Rocket Turbopump Inducer under Lower Cavitation Number
39. 115 Effects of cavitation on blade load near the tip in an inducer
40. 106 Simulation of Vortex Breakdown in a Swirling Flow
41. G602 Investigation of Vortex Breakdown in a Swirling Flow
42. 357 Effects of Temperature of Liquid Nitrogen on Blade Load near the Tip in an Inducer
43. Unsteady Pressure Fluctuations in an Inducer
44. 356 Effect of the Casing Configuration on Internal Flow in an Inducer
45. Observation of cavitation in cryogenic inducer based on unsteady pressure measurements
46. Disturbance Estimation via IMC Design with Limiting Procerties of LQR and Its Application
47. Sealing Characteristics of Solid-Metal Ftat Gaskets
48. Combining IMC Design with H_∞ Control and Its Application to A Two-Finger Robot Hand by Microcomputer Control
49. An Examination on Jobshop Scheduling Problem in consideration of diversity
50. A Study of the Flow from a Circular Plate Oscillating Vertically to the Surface
Catalog
Books, media, physical & digital resources
Discovery Service for Jio Institute Digital Library
For full access to our library's resources, please sign in.