Search

Superconducting (SC) tokamak JT-60SA plays an essential role in fusion research and development by supporting and complementing the ITER project, providing directions to the DEMO design activity and fostering next generation scientists and engineers. Since the short circuit incident at the terminal joints of equilibrium field coil #1 during the integrated commissioning (IC) in March 2021, both EU and JA implementing agencies (IAs) have examined how to ensure safe operation of JT-60SA by mitigating the risk of possible discharge occurrence inside the cryostat. Based on the experience of the global Paschen tests, the IAs have established a strategy of risk mitigation measures, which is a combination of (i) reinforcement of insulation, (ii) avoiding unnecessary voltage application to the coil systems and (iii) immediate de-energization of the coils when deteriorated vacuum conditions are detected. Thanks to the considerable efforts of the Integrated Project Team members, the IC restarted in May 2023. After confirmation of the SC state of the coil systems (TF, EF and CS), the coil energization test and the plasma operation phase 1 (OP-1) started. The first plasma was successfully achieved on 23 October 2023 with a limited value of voltage and current applied to the coils. The plasma configuration control was also confirmed with low plasma current and low auxiliary heating power conditions. Based on the IO–F4E–QST collaboration, activities of JT-60SA have been shared with the IO and provided an important lesson for ITER assembly and commissioning, and will provide an outstanding contribution to fusion research at large. After OP-1, maintenance & enhancement phase 1 (M/E-1) starts from January 2024, in which in-vessel components are installed, and heating and diagnostic systems are extensively upgraded to allow a high power heating experiment planned in OP-2. In order to make the best use of JT-60SA, a newly organized JT-60SA experiment team will refine the research plan for the future high heating power operation phase.

The elimination of the need for an Ohmic heating solenoid may be the most impactful design driver for the realization of economical compact fusion tokamak reactor systems. However, this would require fully non-inductive start-up and current ramp-up from zero plasma current and low electron temperature of sub-keV to the full plasma current of ∼10–15 MA at 20–30 keV electron temperature. To address this challenge, an efficient solenoid-free start-up and ramp-up scenario utilizing a low-field-side-launched extraordinary mode at the fundamental electron cyclotron harmonic frequency (X–I) is proposed, which has more than two orders of magnitude higher electron cyclotron current drive (ECCD) efficiency than the conventional ECCD for the sub-keV start-up regime. A time dependent model was developed to simulate the start-up scenarios. For the Spherical Tokamak Advanced Reactor (STAR) (Menard et al 2023 Next-Step Low-Aspect-Ratio Tokamak Design Studies (IAEA)), it was found that to fully non-inductively ramp-up to 15 MA, it would take about 25 MW of EC power at 170 GHz. Because of the relatively large plasma volume of STAR, radiation losses must be considered. It is important to make sure that high Z impurities are kept sufficiently low during the early current start-up phase where the temperature is sub-keV range. Since the initial current ramp up takes place at a factor of ten lower density compared to the sustained regimes, it is important to transition into a higher bootstrap fraction discharge at lower density to minimize the ECCD power requirement during the densification. For the sustainment phase an array of eight gyrotron launchers with a total of about 60 MW of fundamental O-mode was found to be sufficient to provide the required axis-peaked external current drive. High efficiencies between 19–57 kA MW ^−1 were found with optimal aiming, and these were resilient to small changes in aiming angles and density and temperature profiles.

The plasma current start-up experiment is conducted through electron cyclotron (EC) heating in the QUEST spherical tokamak. During the EC heating, the application of a toroidal electric field in the opposite direction to the plasma current effectively inhibits the growth of energetic electrons. Observations show rapid increases in plasma current and hard x-ray count immediately following the cancellation of the retarding electric field. When a compact tokamak configuration maintains equilibrium on the high field side, along with the retarding field, it leads to effective bulk electron heating. This heating achieved an electron temperature of T _e ≈ 1 keV at electron density n _e > 1.0 × 10 ^18 m ^−3 . Ray tracing of the EC wave verifies that more power absorption into plasma through a single-pass occurs around the second resonance layer with higher values of electron density and temperature.

Results from the successful solenoid-free plasma startup using the method of transient coaxial helicity injection (transient CHI) in the QUEST spherical tokamak (ST) are reported. Unlike previous applications of CHI on HIT-II and on NSTX which required two toroidal insulating breaks to the vacuum vessel, QUEST uses a first of its kind, floating single biased electrode configuration, which does not use such a vacuum break. Instead, the CHI electrode is simply insulated from the outer lower divertor plate support structure. This configuration is much more suitable for implementation in a fusion reactor than the previous configurations. Transient CHI generated toroidal currents of 135 kA were obtained. The toroidal current during the formation of a closed flux configuration was over 50 kA. These results bode well for the application of transient CHI in a new generation of compact high-field STs and tokamaks in which the space for the central solenoid is very restricted.

Spatially resolved rotational temperature of ground state hydrogen molecules desorbed from plasma-facing surface was measured in QUEST, LTX-β, and DIII-D tokamaks, and the increases of the rotational temperature with the surface temperature and due to collisional-radiative processes in the plasmas were evaluated. The increase due to collisional-radiative processes was calculated by solving rate equations considering electron and proton collisional excitation and deexcitation and spontaneous emission. The calculation results suggest a high sensitivity for the rotational temperature to electron and proton densities, but a negligible sensitivity to the electron, proton, and surface temperatures. In the three tokamaks with different plasma parameters and plasma-facing surface materials, the spatial profile of the rotational temperature was estimated using Fulcher-α emission lines (600–608 nm). In QUEST, the spatial profile of the rotational temperature was estimated from spatially resolved spectra. In the other tokamaks, the rotational temperature was evaluated assuming a single point emission with a location determined from the Fulcher-α emission profile as measured with a filtered camera. In metal-walled devices QUEST and LTX-β, the rotational temperature increased with the surface temperature, and the calculated collisional-radiative increase is consistent with measured increase assuming that the rotational temperature at the surface is approximately 500–600 K higher than the surface temperature. In DIII-D with carbon walls, a larger collisional-radiative increase than the other tokamaks was observed because of the higher density leading to a large difference from the calculated increase compared to the other smaller tokamaks. Measurement of the Fulcher-α emission profile with higher spatial resolution in DIII-D may reduce the difference and reveal the effect of the surface temperature on the rotational temperature. These results show the increases in the rotational temperature with the surface temperature and due to the collisional-radiative processes.

A 28 GHz system with a high-power gyrotron tube has been used for the QUEST spherical tokamak to form an over-dense plasma for electron Bernstein wave (EBW) heating and current drive with an 8.2 GHz-wave. Non-inductive high-density plasma ramp-up experiments with dual-frequency (dual-f ) electron cyclotron (EC) (8.2 GHz and 28 GHz) waves were conducted. A spontaneous density jump (SDJ) to an over-dense state was first observed as a bifurcation phenomenon in the dual-f  wave experiment. The over-dense plasma on the 8.2 GHz wave was non-inductively ramped up to 25 kA, and was maintained for 0.4 s under stable plasma equilibrium after two such jumps in one shot. Heating to mildly energetic electrons and bulk electrons was observed even in the over-dense region. The electrostatic EBW heating effect on the mildly energetic electrons in the over-dense region is assessed following a dispersion analysis of the 8.2 GHz wave. The bulk electron heating effect observed is explained as heat exchange from mildly energetic electrons heated by the electrostatic EBW. Remarkably, a high hard-x-ray-radiation temperature of  ∼500 keV was also observed in tangential viewing for current-carrying electrons in the over-dense core region. Synergetic heating from the overlap of different 28 GHz EC harmonic resonances as well as higher harmonic heating is discussed for maintaining the highly energetic electrons in the over-dense core region. In addition, the SDJ process and mechanism are considered based on the discussion of the electron heating effects with the 8.2 GHz wave. [ABSTRACT FROM AUTHOR]

The fuel particle balance during long duration discharges in the Q-shu University Experiment with steady state spherical tokamak (QUEST) was investigated. QUEST has all-metal plasma facing walls (PFWs) that were temperature controlled during the experiments. The presence of a transport barrier for hydrogen (H) at the interface between a plasma-induced deposition layer and metallic substrate was confirmed by nuclear reaction analysis with exposing deuterium plasma. An effective method to evaluate global hydrogen flux to PFWs is proposed, taking advantage of the nature of wall saturation. The outgoing flux of fuel particles from the PFWs just after the plasma termination was proportional to the square of wall-stored H, which indicates that enhanced recombination of solved hydrogen played an essential role in dynamic retention and was in agreement with predictions from the H-barrier model. A simple calculation based on the combination of wall modelling and rate equations of the H states denoted a significant impact of wall modelling on the time response of the plasma density. Hence, a proper wall model including the effects of the deposition layer creating the H barrier is required to be developed, even for all-metal PFW devices. [ABSTRACT FROM AUTHOR]

Megawatt (MW) gyrotrons, with a wide frequency range from 14 to 300 GHz, are being developed as part of a collaborative electron cyclotron heating (ECH) study for advanced fusion devices and a demonstration power plant (DEMO). (1) Detailed designs for a 14 GHz 1 MW gyrotron are being developed for fabrication. For a 14 GHz radio frequency (RF) beam with high divergence, a calculated transmission efficiency of 94% to the corrugated waveguide coupling position was obtained initially by introducing the design concept (direct RF beam coupling by built-in waveguide) to minimize the RF transmission path. Installing a double-disk sapphire window will make it possible to develop a 1 MW gyrotron with a continuous wave (CW) at 14 GHz. (2) In experimental tests of a new 28/35 GHz dual-frequency gyrotron, the cooling characteristics of an optimal-structure double-disk sapphire window were evaluated. We confirmed that operating at 0.4 MW with a CW at 28 GHz is feasible, reaching twice the output power reported in previous studies. In a 2 ms short-pulse experimental test, maximum powers of 1.65 MW at 28.04 GHz and 1.21 MW at 34.83 GHz were achieved. (3) A design study of a 77/51 GHz dual-frequency gyrotron was performed. Oscillations above 1.5 MW for 77 GHz and 1.3 MW for 51.88 GHz are expected for a beam voltage Vk  =  80 kV and beam current Ik  =  60 A. (4) In an experiment with a 300 GHz gyrotron, the influence of the wave reflected from the window was reduced by tilting the output window, and mode competition in the cavity was suppressed. An output power of 0.62 MW with a pulse width of 1 ms, which is the new record for this frequency, was obtained. (5) We also performed a trial design study of a 240 GHz gyrotron for DEMO. [ABSTRACT FROM AUTHOR]

Initial results from the recently implemented transient coaxial helicity injection (CHI) system on QUEST are reported. QUEST uses a new CHI electrode configuration in which the CHI insulator is not part of the vacuum boundary, making this configuration easier to implement in fusion reactors. Experimental results show that transient CHI startup in this alternate electrode configuration is indeed possible. Reliable gas breakdown was achieved, and toroidal currents up to 45 kA were generated. [ABSTRACT FROM AUTHOR]

Intensity fluctuations are investigated using the fast camera imaging technique in the slab annular plasma as a function of magnetic shear and connection length in the spherical tokamak QUEST. Note that here QUEST is operated as a simple magnetized torus with a tight aspect ratio. Slab annular plasmas feature open magnetic field lines and can mimic the tokamak edge-scrape off layer (SOL)-like plasma attributes reasonably well. Three magnetic shear regimes are realized using three poloidal magnetic field (PF) coil pairs. A whole range of connection lengths (∼∞ ≥ Lc ≥ 5.5 m) is scanned by varying the PF strength for a given toroidal field for each magnetic shear regime. For the first time a systematic study of the effect of magnetic shear and field line pitch together on edge-SOL-like plasma fluctuations is being reported. Slab plasmas with intermediate magnetic shear are observed to be more susceptible to generate distinct blobs when Lc is reduced by increasing the PF strength. A distinct coherent mode appears only at the lowest magnetic shear slab featuring a deep potential well. Such mode is not apparent at other magnetic shear cases even at the same Lc. Finally, with a combination of PF coil pairs, both the features of intermediate and low magnetic shear slabs are shown to be realizable simultaneously. Significantly stronger blobs are observed with such combination of PF mirror ratios in the presence of a coherent mode. This study may provide better insight into the effect of magnetic configuration in the tokamak edge and SOL turbulence and can help in searching for better tools to control cross-field convective intermittent transport in tokamaks. [ABSTRACT FROM AUTHOR]

Fully non-inductive second (2nd) harmonic electron cyclotron (EC) plasma current ramp-up was demonstrated with a newlly developed 28 GHz system in the QUEST spherical tokamak. A high plasma current of 54 kA was non-inductively ramped up and sustained stably for 0.9 s with a 270 kW 28 GHz wave. A higher plasma current of 66 kA was also non-inductively achieved with a slow ramp-up of the vertical field. We have achieved a significantly higher plasma current than those achieved previously with the 2nd harmonic EC waves. This fully non-inductive 2nd harmonic EC plasma ramp-up method might be useful for future burning plasma devices and fusion reactors, in particular for operations at half magnetic field with the same EC heating equipment. [ABSTRACT FROM AUTHOR]

Fully non-inductive plasma maintenance was achieved by a microwave of 8.2 GHz and 40 kW for more than 1 h 55 min with a well-controlled plasma-facing wall (PFW) temperature of 393 K, using a hot wall in the middle-sized spherical tokamak QUEST, until the discharge was finally terminated by the uncontrollability of the density. The PFW was composed of atmospheric plasma-sprayed tungsten and stainless steel. The hot wall plays an essential role in reducing the amount of wall-stored hydrogen and facilitates hydrogen recycling. The behaviour of fuel hydrogen in the PFW was investigated by monitoring the injection and evacuation of hydrogen into and from the plasma-producing vessel. A fuel particle balance equation based on the presence of a hydrogen transport barrier between the deposited layer and the substrate was applied to the long-duration discharges. It was found that the model could readily predict the observed behaviour in which a higher wall temperature likely gives rise to faster wall saturation. [ABSTRACT FROM AUTHOR]

Nationally coordinated research on spherical tokamak is being conducted in Japan. Recent achievements include: (i) plasma current start-up and ramp-up without the use of the central solenoid by RF waves (in electron cyclotron and lower hybrid frequency ranges), (ii) plasma current start-up by AC Ohmic operation and by coaxial helicity injection, (iii) development of an advanced fuelling technique by compact toroid injection, (iv) ultra-long-pulse operation and particle control using a high temperature metal wall, (v) access to the ultra-high-β regime by high-power reconnection heating, and (vi) improvement of spherical tokamak plasma stability by externally applied helical field. [ABSTRACT FROM AUTHOR]

Megawatt power gyrotrons are being developed for collaborative electron cyclotron heating (ECH) studies of advanced fusion devices and demonstration power plant (DEMO). (1) In the first experiment of a 300 GHz gyrotron, an output power above 0.5 MW in the TE32,18 single mode was achieved with a pulse width of 2 ms. This was the first observation of MW-scale oscillations in a DEMO-relevant gyrotron mode. It was also found that the reflection at the output window affected the determination of the oscillation mode. Furthermore, several single mode oscillations in the 226–254 GHz range were confirmed, which is important for the step-frequency tunable gyrotron in the sub-THz frequency range. (2) Based on the successful results of the 77 and 154 GHz large helical device (LHD) tubes, a new 154/116 GHz dual-frequency gyrotron with an output of over 1.5 MW is being designed. (3) A new record output of 1.38 MW was obtained using an existing 28 GHz gyrotron. A newly designed tube aimed at achieving a dual-frequency output power of 2 MW at 28 GHz (0.4 MW continuous wave) and 1 MW at 35 GHz was built. In the first experimental test, main mode oscillations were observed at the frequencies of 28.036 and 34.831 GHz with Gaussian-like output beams and output power of 1.27 and 0.48 MW, respectively. A total efficiency of 50% was achieved at 28 GHz operation. [ABSTRACT FROM AUTHOR]

The response of the far scrape-off layer (far-SOL) to strong gas puffing (SGP), and its role as the boundary condition for core plasma, are investigated using a two-point Langmuir probe measurement in the high poloidal beta configuration in the QUEST spherical tokamak. The temperature and heat flux behave in an opposite way in the far-SOL and end-plate region after SGP, although SGP increases the density globally. The apparent density decay time in the far-SOL area is much longer than that in the core. Significant co-current flow is driven solely by the electron cyclotron wave in the far-SOL flow. Sheared flow is also observed in the perpendicular velocity profile during the recovered current flat-top phase, and such flow profiles are flattened by SGP. These flow profiles are attributed not only to drift-driven flow but also to transport-driven flow, the sink effect on the end-plate, and the balance of the neutral particle source. [ABSTRACT FROM AUTHOR]

Megawatt-class gyrotrons covering a wide frequency range (14 GHz–300 GHz) are in increasing demand for nuclear fusion. Recent electron cyclotron heating and electron cyclotron current drive experiments highlight a requirement of megawatt-scale gyrotrons at a relatively lower frequency (14–35 GHz) range of some plasma devices, like GAMMA 10/PDX of the University of Tsukuba, QUEST of Kyushu University, NSTX-U of Princeton Plasma Physics Laboratory, and Heliotron J of Kyoto University. Collaborative studies for designing a new 28 GHz/35 GHz dual-frequency gyrotron and a 14 GHz gyrotron have commenced. Operation above 1 MW of 28 GHz/35 GHz dual oscillation was demonstrated experimentally. Further in the design of dual-frequency gyrotron, operations with 2 MW 3 s and 0.4 MW CW (continuous wave) at 28 GHz, and power exceeding 1 MW for 3 s at 34.8 GHz have been shown to be feasible. The 14 GHz gyrotron is expected to operate above 1 MW. We are also developing higher frequency gyrotrons (77–300 GHz). The joint program of National Institute for Fusion Science and the University of Tsukuba developed two new 154 GHz gyrotrons for the large helical device after the demonstration of three 77 GHz gyrotrons. The 154 GHz gyrotrons achieved a maximum output power of 1.25 MW and quasi-CW operation of 0.35 MW for 30 min. [ABSTRACT FROM AUTHOR]

Successful production of high βp plasmas (εβp ⩾ 1) fully non-inductively (NI) and their long pulse sustainment with the help of modest power (<100 kW) of electron cyclotron waves is demonstrated. High βp plasmas are found for the first time to be naturally self organized to form a stable natural inboard poloidal field null (IPN) equilibrium. A critical βp value is identified, which defines the transition boundary from inboard limiter (IL) to IPN equilibrium. A new feature of plasma self organization is evidenced, which enhances its negative triangular shape to sustain high βp. These results show a relatively simple method to produce and sustain high βp plasma close to the equilibrium limit in a stable configuration exploiting its self organization property. [ABSTRACT FROM AUTHOR]

Effectiveness of high harmonic electron cyclotron resonance heating (ECRH) was investigated by both experiments and ray-trace analyses. The conditions of both the EC wave injection and the magnetic field configuration were optimized in the large helical device. In the case of the second harmonic ordinary mode injection with a frequency of 77 GHz and with the optimized injection angle, about 30–40% absorption could be kept beyond the cut-off density of the second harmonic extraordinary (X2) mode, which is 3.7 × 1019 m−3. In the third harmonic X (X3) mode heating experiment, the dependence of the absorption rate on plasma density and temperature of the target plasma was precisely investigated and compared with the ray-trace (TRAVIS code) calculation. The calculation results of the absorption rate show fairly good agreement with the experimentally obtained ones on the plasma-parameter dependences. The maximum absorption rate in the X3 heating experiment attained approximately 40% around the electron density of 1.5 × 1019 m−3 and the electron temperature of 1.2 keV. Superposed stepwise injection from three gyrotrons with a total of 3 MW increased the central electron temperature to about 3.5 times of the initial target plasma temperature of 0.6 keV. This shows that the temperature increase improves the absorption rate of the subsequent injection. [ABSTRACT FROM AUTHOR]