Search

This article proposes an adaptive scheme for image tampered region localization and content recovery. To generate the watermark information comprised of the authentication data and recovery data, we firstly propose the Adaptive Authentication Feature Calculation algorithm to obtain the authentication data, which includes the information of block location and block feature. The DWT-based Block Feature Calculation method is then proposed to calculate the block feature, and the quantization method is employed to calculate the block location. The recovery data is composed of self-recovery bits and mapped-recovery bits. The self-recovery bits are obtained by the Set Partitioning in Hierarchical Trees encoding algorithm. For retrieving the damaged codes caused by tampering, we propose the Diagonal Mapping algorithm and apply it to the self-recovery bits, thus generating the mapped-recovery bits, to provide a guarantee of recovery data. Experimental results show the superior performance of the proposed scheme in terms of tamper detection and image recovery, by comparing with the state-of-the-art works. The results demonstrate that the proposed method shows efficiency in the adaptiveness, well localization, strong capability for image recovery, and the effectiveness of attack resistance. [ABSTRACT FROM AUTHOR]

Free metal particle can affect surface charge accumulation on epoxy insulator installed in gas-insulated transmission line (GIL) or gas-insulated switchgear (GIS), which results in reduction of surface flashover voltage thus threatening the safe operation of the power equipment. This article reports on the charge accumulation behavior on a real size epoxy insulator with bouncing metal particle under DC voltage. A coaxial electrode system was designed for the test under −30 kV, a metal particle-launching system was employed to inject the bouncing linear particle to the insulator surface. The charge distribution was measured by a Kelvin-type probe, and the influence of the particle on the charge accumulation was analyzed with the help of electric field simulation. The results showed that there were mainly two moving patterns of the bouncing particle: the charges were accumulated with speckle shape and the charged particle that hit the edge of electrode had more remarkable influence on the charge accumulation than other particles. It is suggested that the charge distribution feature is dependent upon the collision point and the trajectory of the bouncing particle. [ABSTRACT FROM AUTHOR]

Surface charge accumulation on epoxy insulator installed in gas-insulated transmission line (GIL) and gas-insulated switchgear (GIS) has been recognized as a crucial factor for electric field distortion that results in the reduction of surface flashover voltage. This article reports on the gaseous ionization dependence of the charge accumulation pattern on a real-size epoxy insulator with multiarc surface profile by using various gas atmospheres. A coaxial electrode system was designed to investigate the charging behavior under dc voltages of −10, −20, and −30 kV. The insulator and electrodes were placed in a metal-enclosed test chamber, which was filled with 0.1 MPa air or 0.4 MPa SF6/N2 mixture to estimate the influence of the gas atmosphere on the charge accumulation behavior by a Kelvin-type probe. The accumulation mechanism and the electric field distortion induced by the charges were demonstrated based on numerical simulation. The results indicated that positive charges were accumulated in the shape of speckle on insulator surface in air, whereas both positive and negative charges were accumulated in SF6/N2 mixture and positive charge speckles appeared in SF6/N2 mixture only when the voltage raised up to −30 kV. It is considered that the charge accumulation behavior is determined by the competition result among the bulk, the gas and the surface conductions. As compared with the case in air, gaseous ionization in SF6/N2 mixture is more difficult to occur, which leads to the obvious difference in the charge accumulation pattern. [ABSTRACT FROM AUTHOR]

Surface charge accumulation on epoxy insulator installed in gas insulated switchgear (GIS) or gas insulated transmission line (GIL) has been recognized as an important factor for electric field distortion that results in reduction of surface flashover voltage. This paper reports on surface charge accumulation behavior on a actual epoxy insulator for 100 kV GIL prototype with multi-arc surface profile. A coaxial electrode system is used to investigate the charging behavior under DC voltages with metal particles positioned at various positions of the surface so as to estimate its influence on the charge accumulation behavior using a Kelvin type probe. The results show that positive charges are accumulated mainly on the nonplanar region around the high voltage electrode in the shape of speckles, and the average charge distribution along the radial direction presented a double-peak feature. Moreover, the charge accumulation is enhanced by metal particles contacting to the grounded electrode. Using a numerical simulation method, it is suggested that the charge accumulation is mainly determined by gaseous ionization which is enhanced by the metal particle induced electric field distortion. [ABSTRACT FROM AUTHOR]