Search

To calibrate non-contact sensors with fast response and high scale factor, it is critical to develop step pulse generators capable of generating standard high voltage step pulses and accurately measuring the generated waveform. In this paper, two types of step pulse generators are designed with output voltages of 2 kV and 100 kV. The 2 kV step pulse generator can generate a step pulse with a rise time of ∼300 ps and an adjustable pulse width. A step pulse with a rise time less than 5 ns and a pulse width over 1 μs can be generated with the 100 kV step pulse generator. The uncertainty of 2 kV step pulse generator is then analyzed by simulations and experiments. Finally, a performance comparison with step pulse generators in previous studies is carried out. Bandwidth, linearity and repeatability of the sensors can be verified with the designed two step pulse generators. [ABSTRACT FROM AUTHOR]

As a means to thwart thermal covert channel attack in a multi-/many-core system, a strong heat noise whose frequency band coincides with that occupied by the thermal covert channel is injected to jam the channel. However, this undiscriminating channel jamming-based countermeasure will fail if a thermal covert channel is allowed to change its transmission frequency dynamically in response to the jamming. To combat this enhanced thermal covert channel, a more advanced countermeasure is needed and thus proposed that checks the frequency spectrum and tracks any possible covert channel. Only after a channel is detected to be susceptible, a thermal noise with this channel frequency is then emitted to jam the covert channel. The communication protocols and frequency changing scheme pertaining to this enhanced thermal covert channel are described in this article. The experimental results confirm that, when the proposed countermeasure is applied, the enhanced thermal covert channel, much more resilient to jamming, suffers from an extremely high packet error rate (PER), which makes any meaningful data leakage practically impossible. As the proposed countermeasure method is poised to contain dangerous thermal covert channel attacks with an anti-jamming capability, it lends itself well to secure multi-/many-core systems. [ABSTRACT FROM AUTHOR]

Owing to the strong penetration ability of X-rays and the imaging visibility, X-ray inspection has been gradually applied to power grids. However, various problems occur in the promotion and application of X-ray inspection in ultra high voltage gas-insulated switchgear (UHV GIS) owing to its large size. These problems relate to parameter selection, photography, protection area, random defect recognition, and risk assessment based on the X-ray image. In this paper, an X-ray digital imaging system is set up for UHV GIS inspection. Parameter selection for UHV GIS is discussed, and we demonstrate that UHV GIS can be photographed under a source-to-detector distance (SDD) of 2.8 m, a tube voltage of 300 kV, and an exposure of >240 mA·s. A photographic method for UHV GIS, entailing adjustment of the position of the imaging plate with a fixed position of the X-ray generator, is proposed to reduce the difficulty in image stitching. The influence of the parameters on imaging quality is discussed, and we show that the brightness and contrast increase with increasing exposure or decreasing SDD. The interactions between parameters are qualitatively introduced. Moreover, the sensitivity of X-ray inspection in UHV GIS is studied under selected parameters, and the sensitivity of X-ray inspection to copper particles and aluminum particles in UHV GIS are shown to be <0.7 mm and <1.1 mm, respectively. Radiation protection for operators is also discussed. In addition, a pseudo-color scheme for identifying random tiny defects is proposed to reduce human error. Finally, the risk level of defects with X-ray inspection is defined by size feature. [ABSTRACT FROM AUTHOR]

The direction of arrival (DoA) estimation performance of three different coarray structures, namely, the nested array, the coprime sampling array, and the sparse ruler array are presented and compared. The coarray concept makes it possible to detect the DoAs of much more sources than the number of physical antennas. Crucial is that for the first time, these coarrays are investigated based on real measurements conducted on a demonstrator platform. Based on the results obtained, the conclusion is clear. The MUSIC algorithm-based coarray concept with spatial smoothing is not suitable for DoA estimation in practical circumstances due to the unavoidable multipath phenomenon. [ABSTRACT FROM AUTHOR]

Overheating is one of the severe defects in gas-insulated switchgear (GIS). However, researches on decomposition characteristics of SF6 under overheating conditions are relatively limited. In this paper, SF6 decomposition products are studied under three overheating conditions which are overheating of solid insulation, overheating of metal, and overheating of metal adjacent to insulating material. Influence of overheating temperature, gas pressure, initial moisture content and adsorbent on the decomposition characteristics of SF6 is discussed. The results show that typical decomposition products of SF6 under overheating of solid insulation are H2, CO, CO2, CH4, SOF2, SO2, H2S, COS and CF4, and typical decomposition products of SF6 under overheating of metal are SOF2, SO2, CO and CO2. Besides, typical decomposition products of SF6 under overheating of metal adjacent to insulating material are CO, CO2, SOF2, SO2, CF4, CS2 and COS. Types of overheating can be recognized by characteristic ratio of (SOF2+SO2)/(CO+CO2): for overheating of solid insulation, the ratio is 0 to 0.25, and for overheating involving metal, it is greater than 1. Two types of overheating involving metal can be distinguished by their characteristic products such as CS2, COS and CF4. [ABSTRACT FROM AUTHOR]

The capillary-based pulsed plasma thruster (PPT) has high-energy transfer efficiency, which provides potential to improve traditional PPT performance. In this paper, the discharge characteristics of a capillary-based PPT have been investigated. First, the typical process of voltage and current waveform is recognized. It is featured with a fast voltage drop (~25 ns) and a consequent damped sine wave oscillation discharge. Then based on the circuit analysis, the equivalent plasma resistance has been calculated. The current waveform is well fit with a linearly increasing resistance model. The influence of charging voltage has also been studied. The deposited energy increases while the transfer efficiency decreases with the increasing applied voltage. The cavity dimension has effects on the equivalent circuit parameters. The results show that longer cavity and smaller diameter lead to more deposited energy and higher transfer efficiency. The influence of voltage and capillary dimension on the mass shot characteristic has been discussed. Finally, the estimated impulse bit has been calculated and the impulse bit characteristics have been discussed. These results can contribute to the further optimization of PPT. [ABSTRACT FROM PUBLISHER]

The lifetime tests for High Voltage Ceramic Capacitors (HVCC) were investigated under repetitive frequency operation at 25 Hz and three kinds of failure modes were summarized. The significant innovation of this paper is testing HVCC, made in the laboratory, under repetitive pulses and proposing several effective improvement methods. The results show that the lifetime of HVCC meets inverse power-law with the applied voltage and the voltage acceleration factor is about 5.8. Failure modes of HVCC are inner breakdown of ceramic dielectric, interface breakdown of ceramic-epoxy and abscission of brass terminals. The inner breakdown is in connection with abrupt destructive discharge under much higher stress while the interface breakdown is related to interface delamination and development of electrical trees in relatively low strength. The third failure mode is always caused by high current density. Based on the failure modes, several methods were taken to improve the performance of HVCC, which included coating semiconductor at the edge of silver layers, adding coupling agent to ceramic-epoxy interface and improving the structure of brass terminals. The lifetime of HVCC under repetitive frequency operation has been extended greatly from 103 shots to more than 105 shots after the investigation and improvement. [ABSTRACT FROM AUTHOR]