Search

A prototype of an Apple-II elliptically polarized undulator (EPU4.6), of length 0.46 m, has been constructed to test the performance of the newly designed magnet block, which was magnetized at a tilt angle 10°. The magnet design and various mechanism analysis are performed to clarify the error source of multipole field components. Good end pole design in the EPU4.6 revealed the variation of the first integral field strength as function of gap and phase is minimized. Shimming algorithm had been used to improve the field quality and phase error. We report here the scheme of the magnetized block arrangement, an analysis of the design mechanism, the end pole design, field shimming and the final test performance using the Hall-probe mapping system. [ABSTRACT FROM AUTHOR]

The wire windings and magnetic performance of the mini-pole superconducting undulator (SCU) at the National Synchrotron Radiation Research Center (NSRRC) are being improved. NbTi superconducting (SC) wire with a rectangular cross section 0.51 mm x 0.77 mm was wound on a racetrack iron pole. The designed field strength was 1.4 T at excitation current 510 A. The bath LHe-cryostat cools the SC wire directly and uniformly using LHe. A stainless-steel (SS) beam duct (thickness 0.3 mm) is designed to separate the ultra-high vacuum (UHV) from the storage ring and the LHe. The SS beam duct is glued to the dummy arrays with resin epoxy. The dummy arrays provide a strong support for the beam duct, providing against deformity from a pressure differential. A vacuum test was performed with a short version of a beam duct (length 400 mm) at low temperature. This paper describes the construction of the magnet, the measurement of the field and the testing of the SS beam duct. [ABSTRACT FROM AUTHOR]

A cryogen-free cryostat for a superconducting undulator with a period of 15 mm (SU15) was developed at the National Synchrotron Radiation Research Center (NSRRC). A 0.44 mm-thin superconducting NbTi wire was wound on iron pole with a racetrack profile. The design field strength of SU15 was 1.4 T and the coil had 148 turns/pole at 230 A; the magnet gap was 5.6 mm. The liquid helium (LHe) recondensation cryostat was designed for SU15. The cryostat provides the advantage of uniform cooling and reduces the amount of LHe consumed. A 0.3 mm-thick stainless steel (SS) beam duct was formed to separate the vacuum in the storage ring from the magnet. Therefore, all of dirty material is produced out of storage ring vacuum. Most of the heat leaked from the LHe vessel leaks from the LHe-fill port heat leak and the 300 K-4.2 K beam duct or was associated with image current power dissipation (ICPD) and bending magnet power dispersion (BMPD). The leaking of heat from the main coil was prevented by the high-temperature superconducting current leads (HTSC). The beam duct was coated with a copper layer with a high-RRR ratio to reduce image current heating. The heat loads on the magnet were cooled using two 1.5 W Gifford-MacMahon (GM) type cryocoolers via LHe medium. [ABSTRACT FROM AUTHOR]

A mini-pole planar vertically-wound racetrack coil undulator was studied to determine its potential for use as a hard X-ray source in a 3 GeV storage ring. A field strength of 1.4 T can be obtained for a superconducting undulator with a periodic length of 1.5 cm and a fixed magnetic gap of 5.6 mm. The magnetic circuit was optimized and a current density of 1090 A/mm², at 80% of the critical current, meets the field strength requirement. A prototype with 40 poles was constructed to verify the design of the magnet and the performance of NbTi superconductor. Additionally, the magnetic field shimming method was developed for spectrum shimming. This study discusses the design of the magnetic circuit and the structure of the magnetic array, the field shimming technique, and the test results of the prototype magnet. [ABSTRACT FROM AUTHOR]

Mini-pole (short period) in-vacuo superconducting undulators, a vert5ical-winding racetrack coil structure, a horizontal-winding racetrack coil structure and a staggered array structure, were studied for use in the X-ray source in a 1.5 GeV or a medium-energy 3 GeV storage ring. The magnetic arrays are all installed in the ultra-high vacuum environment, required for passing electron beams. In a periodic length of 15 mm and a gap of 5 mm, field strengths of 1.5 T, 1.5 T and 0.7 T can be generated in the three different structures, respectively. Additionally, the staggered undulator with variable-period length or a translator structure with different periodic length can yield various deflection parameters k, by driving a longitudinal solenoid field of 0.8 T. Accordingly, this study addresses the magnet structure of and mechanism of the magnet, and the advantages and disadvantages of the structures of these undulators. The spectral characteristics and the magnetic field features of these undulators are also studied. [ABSTRACT FROM AUTHOR]