Search

Our objective was to use shear wave elastography (SWE) to characterize the mechanical properties of an arterial wall with a simulated calcified plaque in an ex vivo setup. A small porcine aorta was used as a model for a human carotid artery and attached to a fixture while pressurized with a water column. The stiffness of the arterial wall and a simulated plaque were estimated using SWE. The mean arterial wall and plaque shear modulus varied from 42 +/- 0 kPa to 100 +/- 1 kPa and 81 +/- 2 kPa to 174 +/- 2 kPa respectively over a pressure range of 20-120 mmHg. The results show the ability of SWE to characterize the mechanical properties of an arterial wall with a simulated plaque and take steps toward an in vivo implementation for quantitative plaque assessment., QC 20160112

In recent years, computational fluid dynamics (CFD) simulations on in-silico models of the heart have provided a valuable insight into cardiac hemodynamic behaviour. However, so far most models have been either based on simplified geometries or on imaging acquisitions with relatively low temporal resolution. It has been suggested that models based entirely on subject-specific ultrasonic images should be used to capture transient flow changes. Therefore, the aim of this study is to present a pathway from routine 4D echocardiography to a patient-specific flow simulation of the left ventricle (LV), evaluating the model robustness and clinical feasibility. The created pathway consisted of initial LV segmentation and mitral/aortic valve positioning, being subsequently used as input for the CFD simulations (based on solving the Navier-Stokes equation using an Arbitrary Lagrangian-Eulerian approach). The output consisted of 4D blood flow velocities and relative pressures in the entire LV. On five subjects, the model robustness was evaluated with regards to variations in singular boundary conditions. The clinical feasibility of the output was compared to clinical PW Doppler measurements and, as a proof-of-concept, synthetic contrast enhanced ultrasound images were simulated on the flow field using the COLE-method. Results indicated a relatively robust model, with variations in regional flow of approximately 5.1/6.2% and 9.7/7.0% for healthy and pathological subject respectively (end diastole/end systole). Furthermore, showing similar behaviour to clinical Doppler measurements the technique serves as a promising tool for future clinical investigations. Additionally, the ability of simulating synthetic ultrasound images further underlines the applicability of the pathway, being potentially useful in studies on improved echocardiographic image analysis., QC 20160112

Treatment decision for coronary artery disease (CAD) is based on both morphological and functional information. Image fusion of coronary computed tomography angiography (CCTA) and three-dimensional echocardiography (3DE) could combine morphology and function into a single image to facilitate diagnosis. Three semi-automatic feature-based algorithms for CCTA/3DE registration were implemented and applied on CAD patients. Algorithms were verified and compared using landmarks manually identified by a cardiologist. All algorithms were found feasible for CCTA/3DE fusion., QC 20160112

Characterization of vulnerable plaques in the carotid artery is critical for the prevention of ischemic stroke. However, ultrasound-based methods for plaque characterization used in the clinics today are limited to visual assessment and evaluation of plaque echogenicity. Shear Wave Elastography (SWE) is a new tissue characterization technique based on radiation force-induced shear wave propagation with potential use in plaque vulnerability assessment. The purpose of this study was to develop an experimental setup to test the feasibility of SWE for carotid plaque characterization. A carotid artery phantom with a soft inclusion in the wall, mimicking a vulnerable plaque, was constructed (10% polyvinyl alcohol (PVA), 3% graphite) by exposing the vessel and plaque to three and one freeze-thaw cycles (6h freeze, 6h thaw) respectively. An Aixplorer SWE system (Supersonic Imagine) was used to measure the shear wave speed (cT) in the vessel wall and plaque. The Young's modulus (E) was then calculated via the Moens-Korteweg (M-K) equation. For comparison, eight cylinders (d = 4 cm, h = 4 cm) were constructed for mechanical testing from the same PVA batch, of which four were exposed to three freeze-thaw cycles (mimicking the vessel wall) and four to one freeze-thaw cycle (mimicking the plaque). The Young's moduli for the cylinders were obtained via a displacement controlled mechanical compression test (Instron 5567) by applying 5% strain. The mean shear wave speed was 2.6 (±0.7) m/s in the vessel wall, 1.8 (±0.7) m/s in the plaque, resulting in Evessel = 11.5 (±0.5) kPa, Eplaque = 4.3 (±0.5) kPa. The compression tests resulted in E = 64.2 (±11.1) kPa in the hard cylinder and E = 9.7 (±3.1) kPa in the soft cylinder. The results showed that it was possible to distinguish between the arterial wall and the plaque. The disagreement between mechanical testing and SWE can be explained by the fact that the shear wave does not propagate monochromatically in cylindrical geometry. To ac, QC 20130910

Carotid strain imaging using ultrasound-based speckle tracking has showed potential in risk stratification of cardiovascular diseases. However, assessing strain in the artery wall and in atherosclerotic plaques is challenging because of small dimensions and low deformations in relation to the applied ultrasound wavelength. High-resolution ultrasound has potential to improve the speckle tracking performance by increasing spatial resolution. The aim of this study was to compare carotid strain estimation by speckle tracking using standard clinical ultrasound and high-resolution ultrasound in an experimental setup. Ultrasound long-axis images were obtained using a standard clinical ultrasound system (Vivid7) and a high-resolution ultrasound system (Vevo2100) in dynamic phantoms mimicking the carotid artery. Speckle tracking was performed to estimate radial and longitudinal strain whereas sonomicrometry was used as reference. The results showed a significant better performance for speckle tracking applied on images from the high-resolution system compared to the standard clinical system., QC 20130910

There are advantages of using a polymeric shelled contrast agent (CA) during ultrasound imaging instead of lipid shelled CA, e.g. particles can be attached to the surface, which enables an introduction of antibodies to the surface making the CA target specific. For this application it is essential to have a sensitive imaging technique suitable for polymeric CA. However, previously presented results have indicated difficulties in visualizing polymeric CA with commercially available contrast algorithms. Therefore a new subtraction algorithm (SA), was developed that define the difference between contrast and reference images. The aim of this study was to evaluate the response from a polymeric CA, when using the SA and compare it with existing contrast algorithms. Moreover, the possibility to detect a thin layer of CA was tested using the SA. Ultrasound short-axis images of a tissue-mimicking vessel phantom with a pulsating flow were obtained using a GE Vivid7 system (M12L) and a Philips iE33 system (S5-1). Repeated (n=91) contrast to tissue ratios (CTR) calculated at various mechanical index (MI) using the contrast algorithms pulse inversion (PI), power modulation (PM) and SA at a concentration of 105microbubbles/ml. The developed SA showed improvements in CTR compared to existing contrast algorithms. The CTRs were -0.99 dB ± 0.67 (MI 0.2), 9.46 dB ± 0.77 (MI 0.4) and 2.98 dB ± 0.60 (MI 0.8) with PI, 8.17 dB ± 1.15 (MI 0.2), 15.60 dB ± 1.29 (MI0.4) and 11.60 dB ± 0.73 (MI 0.8) with PM and 14.97 dB ± 3.97 (MI 0.2), 20.89 dB ± 3.54 (MI 0.4) and 21.93 dB ± 4.37 (MI 0.8) with the SA. In addition to this, the layer detection, when using the SA was successful., © 2011 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works. QC 20111202

Ultrasound-based algorithms are commonly used to assess mechanical properties of arterial walls in studies of arterial stiffness and atherosclerosis. Speckle tracking based techniques used for estimation of myocardial strain can be applied on vessels to estimate strain of the arterial wall. Previous elastography studies in vessels have mainly focused on radial strain measurements, whereas the longitudinal strain has been more or less ignored. However, recently we showed the feasibility of speckle tracking to assess longitudinal strain of the carotid artery in-silico. The aim of this study was to test this methodology in-vivo. Ultrasound images were obtained in seven healthy subjects with no known cardiovascular disease (39 ± 14 years old) and in seven patients with coronary artery disease (CAD), (69 ± 4 years old). Speckle tracking was performed on the envelope detected data using our previous developed algorithm. Radial and longitudinal strains were estimated throughout two cardiac cycles in a region of interest (ROI) positioned in the posterior vessel wall. The mean peak systolic radial and longitudinal strain values from the two heart cycles were compared between the groups using a student's t-test. The mean peak radial strain was -39.1 ± 15.1% for the healthy group and -20.4 ± 7.5% for the diseased group (p = 0.01), whereas the mean peak longitudinal strain was 4.8 ± 1.1% and 3.2 ± 1.6% (p = 0.05) for the healthy and diseased group, respectively. Both peak radial and longitudinal strain values were thus significantly reduced in the CAD patient group. This study shows the feasibility to estimate radial and longitudinal strain in-vivo using speckle tracking and indicates that the method can detect differences between groups of healthy and diseased (CAD) subjects., QC 20111201

Ultrasound based estimation of arterial wall properties is commonly used to assess vessel wall stiffness in studies of vascular diseases. Recently, it was shown that the longitudinal motion of the vessel during systole can be measured using speckle tracking. However, the assessment of longitudinal strain in the vessel wall has to be further investigated. The aim of this study was to test the feasibility of simultaneous assessment of radial and longitudinal strain in the carotid artery using computer simulations. A kinematic cylindrical model of the carotid artery with realistic dimensions was constructed. The model was deformed radially according to temporal distention measured in-vivo while longitudinal deformation was the result of conservation of volume. Moreover, longitudinal motion was superimposed based on profiles obtained in-vivo. Ultrasound long axis images were simulated using a generalized convolution model (COLE) with realistic image properties. Four models with different scatterer distributions were built. For each of them, longitudinal and radial motion were estimated using normalized cross-correlation with spline interpolation to detect sub-sample motion. Radial and longitudinal strains, obtained by linear regression were compared with the ground truth from the model. The maximal systolic radial strain was estimated to be -12.77 ± 0.4% (ground truth -13.89%) while longitudinal strain was 5.21 ± 0.67% (ground truth 5.3%). This study shows the feasibility of simultaneously measuring radial and longitudinal strain in the carotid artery by making use of currently available hardware., QC 20100727