Search

The influence of the channel hole remaining ratio (CHRR) on the hemi-cylindrical (HC) vertical NAND (VNAND) flash memory was investigated using both simulation and experimental data. Although HC VNAND flash memory is advantageous for increasing lateral memory density, it suffers from nonuniform carrier injection and low program/erase efficiency. In this study, the underlying physics of these disadvantages are discussed in terms of the proposed parameter, CHRR. Finally, based on the analysis, a recessed channel HC VNAND flash memory cell is proposed. [ABSTRACT FROM AUTHOR]

Objective: Two-dimensional (2D) photoacoustic (PA) imaging based on array transducers provide high spatial resolution in the lateral direction by adopting receive dynamic focusing. However, the quality of PA image is often deteriorated by poor elevational resolution which is achieved by an acoustic lens. To overcome this limitation, we present a three-dimensional (3D) image reconstruction method using a commercial one-dimensional (1D) array transducer. Methods: In the method, the elevational resolution is improved by applying synthetic aperture focusing (SAF) technique along the elevational direction. For this, a commercially available 1D array transducer with an acoustic lens is modeled and appropriate synthetic focusing delay that can minimize the effect of the acoustic lens is derived by mathematical analysis. Results: From the simulation and experiment results, it was demonstrated that the proposed method can enhance the image quality of PA imaging, i.e., elevational resolution and signal-to-noise ratio (SNR). Conclusion: 3D PA images with improved elevational resolution were achieved using a clinical 1D array transducer. Significance: The presented method may be useful for clinical application such as detecting microcalcification, imaging of tumor vasculature and guidance of biopsy in real time. [ABSTRACT FROM AUTHOR]

As a molecular imaging modality, photoacoustic (PA) imaging has been in the spotlight because it can provide an optical contrast image of physiological information and a relatively deep imaging depth. However, its sensitivity is limited despite the use of exogenous contrast agents due to the background PA signals generated from nontargeted absorbers, such as blood and boundaries between different biological tissues. In addition, clutter artifacts generated in both in-plane and out-of-plane imaging region degrade the sensitivity of PA imaging. We propose a method to eliminate the nontargeted PA signals. For this study, we used a dual-modal ultrasound (US)-PA contrast agent that is capable of generating both the backscattered US and PA signals in response to the transmitted US and irradiated light, respectively. The US images of the contrast agents are used to construct a masking image that contains the location information about the target site and is applied to the PA image acquired after contrast agent injection. In vitro and in vivo experimental results demonstrated that the masking image constructed using the US images makes it possible to completely remove nontargeted PA signals. The proposed method can be used to enhance the clear visualization of the target area in PA images. [ABSTRACT FROM AUTHOR]

We developed a forward-looking (FL) multimodal endoscopic system that offers color, spectral classified, high-frequency ultrasound (HFUS) B-mode, and integrated backscattering coefficient (IBC) images for tumor detection in situ. Examination of tumor distributions from the surface of the colon to deeper inside is essential for determining a treatment plan of cancer. For example, the submucosal invasion depth of tumors in addition to the tumor distributions on the colon surface is used as an indicator of whether the endoscopic dissection would be operated. Thus, we devised the FL multimodal endoscopic system to offer information on the tumor distribution from the surface to deep tissue with high accuracy. This system was evaluated with bilayer gelatin phantoms which have different properties at each layer of the phantom in a lateral direction. After evaluating the system with phantoms, it was employed to characterize forty human colon tissues excised from cancer patients. The proposed system could allow us to obtain highly resolved chemical, anatomical, and macro-molecular information on excised colon tissues including tumors, thus enhancing the detection of tumor distributions from the surface to deep tissue. These results suggest that the FL multimodal endoscopic system could be an innovative screening instrument for quantitative tumor characterization. [ABSTRACT FROM AUTHOR]

Objective: Interventional ultrasound imaging is a prerequisite for guiding implants and treatment within the hearts and blood vessels. Due to limitations on the catheter's diameter, interventional ultrasonic transducers have side-looking structures although forward-looking imaging may provide more intuitive and real time guidance in treating diseased sites ahead of catheters. To address the issue, a magnetically actuated forward-looking interventional ultrasound imaging device is implemented for the first time. Methods: A forward-looking catheter containing a 1 mm ring type focused 35 MHz ultrasound transducer and a micro magnet, was fabricated. For imaging, the transducer was placed at the center of four electromagnetic coils positioned on four sides of a squared acrylic housing. By modifying the magnetic field, the catheter tip could be remotely translated for sector scanning. Results: The scanning angle could reach up to 3° in 1 Hz with 15 mT, while wider angles of 5° could be achieved with a higher magnetic field of 25 mT for ex-vivo imaging. The position of the transducer could be detected by monitoring the motion with a CCD camera, mimicking clinical X-ray imaging. In the wire target and tissue mimicking phantom studies, the measured hole size, spatial resolution and distance between wires by the proposed system were comparable with the values from a linear scanner. Multi-frame real time data acquisition was demonstrated via ex-vivo imaging on a pig's coronary artery. Conclusion/Significance: The feasibility of magnetically actuated forward-looking interventional ultrasound imaging was demonstrated. The remote-controlled scanning method may allow to simplify the structures of forward-looking interventional ultrasound imaging catheters. [ABSTRACT FROM AUTHOR]

Bioresorbable vascular scaffold (BVS) has recently been spotlighted for its unique characteristics of absorbing into blood vessels and eventually disappearing. Although intravascular ultrasound (IVUS) is the most common guiding tool for stent deployment, the echogenicity of BVS struts has changed as the center of stent lumen and scanning rotation is not concentric, which may cause a critical erroneous measurement in practice. This study investigated the physical conditions for dimming the stent brightness in IVUS images using a finite-difference method (FDM) to numerically solve acoustic wave propagation through nonhomogeneous medium. The dimmed brightness is caused by an angled rectangular cross section of a strut and its similar acoustic impedance with water. Imaging frequency is not a major cause. However, the angle between the acoustic beam and the BVS surface is the major cause of the dimmed brightness. As a solution, an approach using a frequency compounding method with signal polarity comparator was proposed to recover the reduced brightness without sacrificing spatial resolutions. Based on the simulation study, the signal level from BVS can be attenuated down by 17 dB when the angle between the acoustic beamline and the surface of BVS is more than 45°. With the proposed frequency compounding approach, the reduced signal can be recovered by 6 dB. In the experimental BVS IVUS imaging, strut brightness was reduced by 18 dB with an angled strut position and recovered by 5 dB with the proposed frequency compounding method. A pig coronary was imaged to demonstrate the performance of the proposed method. [ABSTRACT FROM AUTHOR]

Objective: For accurate diagnosis of atherosclerosis, the high spatial and contrast resolutions of intravascular ultrasound (IVUS) images are a key requirement. Increasing the center frequency of IVUS is a simple solution to meet this requirement. However, this leads to a reduction in imaging depth due to the frequency-dependent attenuation of ultrasound. Here, we report a recently developed dual-element IVUS transducer for tissue harmonic imaging (THI) and frequency compounding to increase the spatial and contrast resolutions of IVUS images, while maintaining the imaging depth to assess the overall morphological change of blood vessels. Methods: One 35-MHz element is used for producing general IVUS images and the other 70-MHz element is for receiving the second harmonic signals induced by the 35-MHz ultrasound. The fundamental and second harmonic signals can also be used for frequency compound imaging to further improve contrast resolution. The spatial and contrast resolutions achieved by the developed transducer were evaluated through wire and tissue-mimicking phantom imaging tests. Additionally, the images of a stent deployed in a tissue-mimicking phantom and an excised pig artery were acquired to assess clinical usefulness of the transducer. Results: The results demonstrated that the developed IVUS transducer enables us to simultaneously examine the overall morphological change of blood vessels by the 35-MHz ultrasound images and the near vessel layers such as the intima, the media, and the adventitia by either THI or compound images with high spatial and contrast resolutions. In addition, the developed transducer facilitates the simultaneous acquisition of 35- and 70-MHz fundamental images when needed. Conclusion: The developed dual-element IVUS transducer makes it possible to fully realize the potential benefits of IVUS in the diagnosis of atherosclerosis. [ABSTRACT FROM AUTHOR]

A noncontact single-beam acoustic trapping technique has proven to be a promising tool for cell manipulation and characterization that provide essential knowledge for a variety of biomedical applications. Here, we investigated cell characteristics as to whether the calcium responses of suspended breast cancer cells to different acoustic trapping forces are related to their invasiveness. For this, we combined a single-beam acoustic trapping system with a 30-MHz press-focused lithium niobate ultrasound transducer and an epifluorescence microscope. Using the system, intracellular calcium changes of suspended MDA-MB-231 (highly invasive) and MCF-7 (weakly invasive) cells were monitored while trapping the cells at different acoustic pressures. The results showed that a single suspended breast cancer cell isolated by the acoustic microbeam behaved differently on the calcium elevation in response to changes in acoustic trapping force, depending on its invasiveness. In particular, the MDA-MB-231 cells exhibited higher calcium elevation than MCF-7 cells when each cell was trapped at low acoustic pressure. Based on these results, we believe that the single-beam acoustic trapping technique has high potential as an alternative tool for determining the degree of invasiveness of suspended breast cancer cells. [ABSTRACT FROM AUTHOR]

Although transrectal ultrasound (TRUS) imaging is widely used for screening and diagnosing prostate cancer, it is often not found on TRUS images, depending on its stage, size, and location. In addition, due to the weak echo signal and the low contrast of TRUS images, it is difficult to diagnose early-stage prostate cancers and distinguish malignant tumors from benign prostatic hyperplasia. For this reason, TRUS image-guided biopsy is mandatory to confirm the malignancy of the suspicious tumor, but the diagnostic accuracy of initial biopsy is only 20%–30%, so that the patients inevitably undergo repeated biopsies. TRUS-photoacoustic (TRUS-PA) imaging is one way to resolve those problems. However, the development of a TRUS-PA probe, in which an ultrasound array transducer and optical fibers are integrated, is demanding because the overall size of the probe should be as small as possible for the convenience of the patients, while providing the desired performances. Here, we report a recently developed TRUS-PA probe. The core element of the TRUS-PA is a miniaturized 128-element, 7-MHz convex array transducer of which size in the lateral and elevational directions is 11.4 and 5 mm, respectively. A new concept of a flexible printed circuit board was also developed to limit the size of the TRUS-PA probe to less than 15 mm. From the performance evaluation, it was found that the developed array with a field-of-view of 134° has a center frequency of 6.75 MHz, a −6-dB fractional bandwidth of 66%, and a crosstalk of less than −45 dB. In the tissue-mimicking phantom test andex vivoexperiments, the miniaturized convex array proved to be capable of providing combined US and PA images with acceptable imaging quality in spite of its small size. [ABSTRACT FROM AUTHOR]

Tissue harmonic imaging (THI), an essential mode of commercial ultrasound imaging scanners, can provide images with high spatial and contrast resolutions. For THI, the frequency spectrum of a transducer is generally divided for the transmission of fundamental signal and the reception of its second harmonic. Therefore, it is difficult to use the THI mode for intravascular ultrasound (IVUS) imaging because typical IVUS transducers have a narrow −6-dB fractional bandwidth of about 50%. Due to its small aperture (about 0.5 mm) and the strength of IVUS being too weak, it is difficult to construct a high-quality tissue harmonic image. In this paper, we report a recently developed dual-frequency oblong-shaped-focused IVUS transducer for high-quality intravascular THI; the transducer consists of three elements arranged side by side in the horizontal (i.e., elevation) direction. The two outer elements with a center frequency of 35 MHz are responsible for ultrasound transmission and the center element has a center frequency of 70 MHz for the reception of the second-harmonic signals. All three elements have a spherical shape with a radius of 3 mm to efficiently generate harmonics in the region of interest. This configuration of the developed IVUS transducer was determined to facilitate high-quality THI, which was based on the results of Field II simulation and finite-element analysis. The images of wires and a tissue-mimicking phantom indicated that the tissue harmonic images produced by the developed transducer have not only a high spatial resolution but also a deep imaging depth, compared to the 35- and 70-MHz fundamental images. [ABSTRACT FROM AUTHOR]

Photoacoustic (PA) imaging detects acoustic signals generated by thermal expansion of a light-excited tissue or contrast agents. PA signal amplitude and image quality directly depend on the light fluence at the target depth. With conventional PA imaging systems, approximately 30% energy of incident light at the near-infrared region would be lost due to reflection on the skin surface. Such light loss directly leads to a reduction of PA signal and image quality. A new light delivery scheme that collects and redistributes reflected light energy was recently suggested, which is called the light catcher. In our previous study, proof of concept using a finite-element simulation model was shown and a laboratory-built prototype of the light catcher was applied on tissue-mimicking phantoms. In this paper, we present an elaborate prototype of a high-frequency PA probe with the light catcher fabricated using 3-D printing technology, which is conformal to a subcutaneous tumor in mice. The in vivo usefulness of the developed prototype was evaluated in a mouse tumor model. Equipped with the light catcher, PA signal amplitude from the clinical photosensitizer injected into the mouse tumor was enhanced by 33.7%, which is approximately equivalent to the percent light loss due to reflection on the skin. [ABSTRACT FROM PUBLISHER]

In intravascular ultrasound (IVUS) imaging, a transducer is inserted into a blood vessel and rotated to obtain image data. For this purpose, the transducer aperture is typically less than 0.5 mm in diameter, which causes natural focusing to occur in the imaging depth ranging from 1 to 5 mm. Due to the small aperture, however, it is not viable to conduct geometric focusing in order to enhance the spatial resolution of IVUS images. Furthermore, this hampers narrowing the slice thickness of a cross-sectional scan plane in the imaging depth, which leads to lowering spatial and contrast resolutions of IVUS images. To solve this problem, we propose an oblong-shaped-focused transducer for IVUS imaging. Unlike the conventional IVUS transducers with either a circular or a square flat aperture, the proposed transducer has an oblong aperture of which long side is positioned along a blood vessel. This unique configuration makes it possible to conduct geometric focusing at a desired depth in the elevation direction. In this study, furthermore, it is demonstrated that a spherically shaped aperture in both lateral and elevation directions also improves lateral resolution, compared to the conventional flat aperture. To ascertain this, the conventional and the proposed IVUS transducers were designed and fabricated to evaluate and to compare their imaging performances through wire phantom and tissue-mimicking phantom experiments. For the proposed 50-MHz IVUS transducer, a PZT piece of 0.5 × 1.0 mm2 was spherically shaped for elevation focus at 3 mm by using the conventional press-focusing technique whereas the conventional one has a flat aperture of 0.5 × 0.5 mm2. The experimental results demonstrated that the proposed IVUS transducer is capable of improving spatial and contrast resolutions of IVUS images. [ABSTRACT FROM AUTHOR]

In this paper, we present a novel system-on-chip (SOC) solution for a portable ultrasound imaging system (PUS) for point-of-care applications. The PUS-SOC includes all of the signal processing modules (i.e., the transmit and dynamic receive beamformer modules, mid- and back-end processors, and color Doppler processors) as well as an efficient architecture for hardware-based imaging methods (e.g., dynamic delay calculation, multi-beamforming, and coded excitation and compression). The PUS-SOC was fabricated using a UMC 130-nm NAND process and has 16.8 GFLOPS of computing power with a total equivalent gate count of 12.1 million, which is comparable to a Pentium-4 CPU. The size and power consumption of the PUS-SOC are 27\times 27~mm^2 and 1.2 W, respectively. Based on the PUS-SOC, a prototype hand-held US imaging system was implemented. Phantom experiments demonstrated that the PUS-SOC can provide appropriate image quality for point-of-care applications with a compact PDA size (200\times 120\times 45~mm^3) and 3 hours of battery life. [ABSTRACT FROM PUBLISHER]