Search

The improvements in signal-to-noise ratio (SNR) are indispensable to obtain the desired output signal of partial discharge (PD) under square wave pulsewidth modulation (PWM) voltage. In this article, the effect of complex PWM voltage parameters (rise time, fall time, frequency, duty cycle) on the SNR of PD tests is investigated. The results revealed that the sensor's high-frequency gain should be increased to improve the SNR under faster switching. PD impulses are more likely to be submerged in the residual interference under high-frequency voltage. The SNR can be improved by only detecting the PD at the rising front because the PD signal overlaps with commutation noise at the falling front of short duty cycle voltage, such as 0.03% duty cycle. The above results can reference the PWM parameters and improve the SNR in PD tests for rotating machines controlled by power electronics. [ABSTRACT FROM AUTHOR]

A novel single-phase pulsewidth modulation (PWM) direct ac–ac converter based on two-level nondifferential dual-buck ac chopper legs with inverting and noninverting operations is first proposed in this article. It has the ability to resolve both voltage sag and swell problems at the same time when used as distributed flexible voltage conditioner. Compared to the traditional ac–ac converter, it has much enhanced system reliability thanks to no shoot-through problems even when all switches of each ac chopper legs are turned on, and therefore, the PWM dead time is not needed leading to improve the utilization of the duty cycles. Only half of the switches in the proposed converter is switched at high frequency during a switching period at most, which significantly reduces the total switching loss. In particularly, the converter has two greatest advantages that it retains the common sharing ground of the input and output and has the same buck/boost operation process for noninverting and inverting modes. In order to fully testify the performance of the proposed converter, a 500-W experimental prototype is built and tested at different conditions. [ABSTRACT FROM AUTHOR]

Direct modulation principle is widely used in modular multilevel converters (MMCs) for its simplicity and natural stability. However, it results in strong active and reactive power coupling. This paper carefully analyzes and identifies four power coupling paths and two power influence factors with the direct modulation principle. Full power decoupling of the MMC can be realized by cutting off the derived coupling paths and compensating the influence factors. However, this will further deteriorate the already poor damping of the MMC and significantly increase dc-bus current fluctuations. To solve this problem, the sources resulting in poor damping are identified and then a new closed-loop dc-bus current controller is incorporated into the control system. Finally, the proposed power decoupling strategy with the newly designed current controller realizes completely decoupled power regulation, avoids overload operation, and obviously improves the dynamic performance of the MMC. Furthermore, it increases the stability of the MMC system under all possible operation conditions. The proposed control strategy is confirmed by experimental results. [ABSTRACT FROM AUTHOR]

The existing power decoupling control method of modular multilevel converter (MMC) was developed from that of conventional two-level voltage source converters. Therefore, it cannot fully realize power decoupling due to neglecting the coupling effects from submodule capacitor voltage, dc current, circulating current as well as control strategies of circulating current, which inevitably results in inaccurate regulation of active and reactive power, deteriorated system dynamic performance, possible overload operation and eventually threatens the safety and stability of MMC. This paper analyzes the intercoupling among all electrical quantities and corresponding control strategies in MMC. An accurate control model of active and reactive power/current with four coupling paths and influence factors in the rotating frame is also established. A full power decoupling control method has been proposed based on the developed model. The proposed control method can realize accurate and completely decoupled active and reactive power regulation, avoid overload operation, and significantly improve the dynamic performance of MMC. Moreover, it facilitates the parameters selection of MMC controller with no extra cost, which is of great significance for practical projects. The effectiveness and accuracy of the proposed analysis and control methods were verified by both simulation and experimental results. [ABSTRACT FROM AUTHOR]

The dc offset and scaling errors in the voltage and current measurements cause the injection of undesired dc and unbalanced currents into the three-phase input currents and subsequently lead to voltage ripple at the dc output voltage of the ac/dc converter. This paper proposes a compensation scheme for current measurement error where the dc offset and scaling errors in the current measurement are estimated from the voltage ripple characteristics of the dc output voltage ripple combining with simple band-pass and low-pass filters. Meanwhile, the dc offset and scaling errors in the voltage measurement can be rejected by using an advanced current controller developed with a proportional resonant plus a repetitive controller designed in the synchronous (d–q) reference frame. The proposed control algorithm is able to effectively reject the impact of both voltage and current measurement error so that the three-phase input currents are regulated to be balanced and sinusoidal with ultralow dc current component. Meanwhile, the dc output voltage is also well regulated to be pure dc with a negligibly small voltage ripple. The proposed compensation method is developed without the need of extra hardware circuit, sensor, or precise information of system parameters so that it can be considered as more cost effective and robust solution. The effectiveness of the proposed solution is verified by experimental results. [ABSTRACT FROM AUTHOR]

The dc offset and scaling errors in the voltage measurements cause the injection of undesired dc and harmonic currents into the three-phase output currents of the grid-connected inverter. This study proposes an enhanced current control scheme to eliminate the dc and harmonic currents caused by voltage distortion and voltage measurement error in three-phase grid-connected inverters. The proposed current controller is designed in the synchronous (d-q ) reference frame and composed of a proportional resonant (PR) controller and a repetitive controller (RC). The role of the RC is to regulate the grid current follow the reference value as well as compensate all 6\rmn\omega {\rm{s}} and (6\rmn\pm 2)\omega{\rm{s}}\,(n= 1,\,2,\,3,\ldots) harmonic components caused by distorted grid voltage and scaling errors. Meanwhile, the PR controller helps to compensate the dc current generated by dc offset measurement errors to guarantee that the three-phase grid currents are balanced and sinusoidal with extremely low dc component. Since the RC employed in the proposed current controller reduces to time delay by four times compared to the conventional RC, the proposed control system ensures good steady-state performance of the grid current without deteriorating its fast dynamic response. The effectiveness of the suggested solution is verified by various experimental tests. [ABSTRACT FROM AUTHOR]

Due to voltage mismatch between phase legs and the dc bus in modular multilevel converters (MMCs), the differential current in MMCs is inherently subjected to circulating even-order harmonics. Repetitive control based active harmonic suppression methods can be adopted to eliminate such harmonics. Nevertheless, conventional repetitive controllers have a relatively slow dynamic response, because all the sampled errors in the past one cycle have to be stored, which causes a response delay for one fundamental period. This paper proposes an improved repetitive control scheme that exclusively copes with even-order harmonics based on the circulating current characteristics of MMC systems. The design details of the even harmonic repetitive control scheme according to the harmonics characteristics are provided. The proposed even-harmonic repetitive control scheme requires halved data memory to store error samplings and the delay introduced by the repetitive controller is also reduced. According to the frequency domain analysis, the even-harmonic repetitive control features faster convergence rate, greater low-frequency gains, higher crossover frequency, and higher tolerance against system frequency deviation, while possessing the same even-order harmonics suppression capability and stability as conventional ones. Simulation and experimental results are presented to show the steady-state harmonics suppression capability, dynamic response, and disturbance tolerance of the proposed even-harmonic repetitive control scheme. [ABSTRACT FROM AUTHOR]

Modular multilevel converters (MMCs) are multi-input multi-output (MIMO) nonlinear systems. The control systems for MMCs are required to simultaneously achieve multiple control objectives, e.g., output current regulation, submodule capacitor voltage control, and circulating ripple currents suppression. Existing cascaded control strategies for MMCs achieve those control objectives with relatively complex controllers, and the controller parameter design is normally difficult for such nonlinear systems with highly coupled states. In view of this, a feedback linearization-based current control strategy is proposed for an MMC system in this paper. The nonlinear state function model of the MMC is presented and transformed to a linearized and decoupled form with the help of the input–output feedback linearization technique. Based on the linearized system, simple linear controllers are employed to regulate the output and inner differential currents of the MMC, which significantly reduces the difficulty in controller design. The stability of the proposed control strategy is analyzed. The experimental verification results show that, compared to the conventional cascaded control strategies for MMCs, the proposed feedback linearization control strategy is able to achieve improved steady-state and dynamic performances. The robustness of the proposed control strategy against parametric uncertainties is experimentally investigated. [ABSTRACT FROM PUBLISHER]

To ensure insulation system reliability of rotating machines driven by power electronics, accelerated tests under repetitive impulsive voltages should be performed on turn-to-turn insulation according to the standards provided by the International Electrotechnical Commission. The parameters of repetitive impulsive voltage can significantly influence insulation lifetime, and thus, voltage parameters should be carefully controlled during the accelerated tests. To increase endurance test efficiency when testing many insulation specimens in parallel, the rise time of impulsive voltage should be controlled at certain constant values after the breakdown of one or more specimens to obtain objective endurance test results. This study provides a description of a novel square wave voltage generator used for the insulation evaluation of rotating machines driven by power electronics. A single-channel generator with variable rise times used for one specimen and a multi-channel generator with a constant rise time used to test five specimens in parallel are presented based on a push-pull solid-state switch. In the multi-channel generator, the RC parameter of the high-voltage circuit can be adjusted automatically by resorting to controlling units and a circuit structure after the breakdown of one or more samples when performing endurance tests on parallel specimens to keep the rise time of impulsive voltage at constant values. The multi-channel generator can significantly increase the endurance evaluation efficiency of the insulation systems of rotating machines fed by power electronics. [ABSTRACT FROM AUTHOR]

Power allocation is a major concern in hybrid energy storage system. This paper proposes an extended droop control (EDC) strategy to achieve dynamic current sharing autonomously during sudden load change and resource variations. The proposed method consists of a virtual resistance droop controller and a virtual capacitance droop controller for energy storages with complementary characteristics, such as battery and supercapacitor (SC). By using this method, battery provides consistent power and SC only compensates high-frequency fluctuations without the involvement of conventionally used centralized controllers. To implement the proposed EDC method, a detailed design procedure is proposed to achieve the control objectives of stable operation, voltage regulation, and dynamic current sharing. System dynamic model and relevant impedances are derived and detailed frequency domain analysis is performed. Moreover, the system level stability analysis is investigated and system expansion with the proposed method is illustrated. Both simulations and experiments are conducted to validate the effectiveness of the proposed control strategy and analytical results. [ABSTRACT FROM PUBLISHER]

Repetitive control strategies have been commonly applied in pulse-width-modulated (PWM) voltage source inverters (VSIs) for many industrial applications. This paper presents a repetitive controller for voltage harmonic mitigation of VSI-based islanded microgrids. The phase delay in the overall control system, e.g., the delay caused by the digital duty cycle calculation, PWM generation, and repetitive controller, has to be compensated by elaborately designed phase lead filters in order to prevent control performance deterioration and system instability. Nevertheless, quantificational analysis and practical design of the time advance unit in such filters are hardly found in existing literature works. In view of this, this paper proposes an explicit analysis of the phase lead filters and a novel design method of the time advance unit in repetitive controllers to ensure system stability. Moreover, with the help of the proposed method, the overall system stability margin is predictable and improved controller performance is achieved as well. The proposed method is implemented experimentally to show the accurate stability margin calculation as well as the excellent steady state and dynamic performances of the repetitive control scheme. [ABSTRACT FROM PUBLISHER]

Multi-level energy management system (EMS) is proposed for dc microgrids operations to ensure system reliability, power quality, speed of response, and control accuracy in this paper. System distributed control is scheduled as the primary control. Battery energy storages (BESs) operate in voltage regulation mode with droop control for power sharing. However, bus voltage deviation and power tracking error due to line impedance are the main drawbacks of distributed control. To enhance the system power quality and control accuracy, bus voltage restoration and power sharing compensation are implemented in secondary control. Economic dispatch based on comparison of system units' marginal operation costs is carried out in tertiary control to minimize the system operation cost. Detailed elaboration has been derived to quantify BES utilization cost due to the cumulated lifetime degradation. In case of communication failure, system operation can still be retained with primary control without operating mode change so that to enhance system reliability. A lab scale dc microgrid is developed for the verification of the proposed multi-level EMS and relevant control techniques. [ABSTRACT FROM PUBLISHER]

DC microgrids are becoming popular in low-voltage distribution systems due to the better compatibility with photovoltaic panels, electric vehicles, and dc loads. This paper presents a practical dc microgrid developed in the Water and Energy Research Laboratory (WERL) in the Nanyang University of Technology, Singapore. The coordination control among multiple dc sources and energy storages is implemented using a novel hierarchical control technique. The bus voltage essentially acts as an indicator of supply–demand balance. A wireless control is implemented for the reliable operation of the grid. A reasonable compromise between the maximum power harvest and effective battery management is further enhanced using the coordination control based on a central energy management system. The feasibility and effectiveness of the proposed control strategies have been tested by a dc microgrid in WERL. [ABSTRACT FROM PUBLISHER]

Reactive power plays a significant role in power system operation. However, in reliability evaluation, attention has seldom been paid to reactive power. In conventional power system reliability evaluations, the fixed maximum and minimum values are applied as the reactive power limits of generators. Failures of reactive power sources are rarely considered. The detailed causes of network violations for a contingency are also seldom studied. Real power load shedding is usually used to alleviate network violations without considering the role of reactive power. There are no corresponding reliability indices defined to represent the reactive power shortage in the existing techniques. Reactive power shortage and the associated voltage violations due to the failures of reactive power sources are considered in this paper. New reliability indices are proposed to represent the effect of reactive power shortage on system reliability. The reliability indices due to reactive power shortages have been defined and are separated with those due to real power shortages. Reactive power limits determined by real power output of a generator using P-Q curve have been studied. A reactive power injection technique is proposed to determine possible reactive power shortage and location. The IEEE 30-bus system has been modified and analyzed to illustrate the proposed technique. The results provide system planners and operators very important information for real and reactive power management. [ABSTRACT FROM AUTHOR]

This paper presents a uniform control strategy for the bidirectional ac/dc interlinking converter (BIC) in hierarchical controlled hybrid microgrid. The uniform control strategy unifies different control structures for multifunctional BIC in terms of power management, ac and dc voltage support. With the unified control structure, various triggering mechanisms for BIC mode-switch are not compulsory in response to the relevant scenario changes in the power network. Therefore, the negative consequences, such as unsmooth transition and system collapse due to the inaccurate or slower mode switch, can be avoided. Moreover, the uniform control strategy is also applicable for the hierarchical controlled hybrid microgrid, whose control architecture is typically comprised of the centralized and decentralized levels. This enables the communication fault ride-through capability and the impact from the communication failures can thus be mitigated. To sum up the above two features, the proposed control strategy is able to provide a smooth operation for the BIC without control mode switch in the event of unintentional scenario changes in power or communication network. To verify the validity of the proposed uniform control strategy, the controller hardware-in-the-loop experimental results have been provided in this paper. [ABSTRACT FROM PUBLISHER]

Modularity and high reliability from redundancy are the two attractive advantages of modular multilevel converters (MMCs). This paper elaborates a switch open-circuit fault diagnosis and a fault-tolerant operation scheme for MMCs with distributed control. The proposed fault diagnosis and fault-tolerant control method can significantly improve the reliability of the MMC while maintaining the modularity of its software implementation. By distributing fault diagnosis into submodules, its local controller is capable of identifying the switching devices in open-circuit fault without extra hardware circuitry. Based on the real-time measurements of submodule terminal voltage and arm current, single, or multiple faulty switches can be identified within 3.5 ms without triggering faulty alarms. Furthermore, a new fault-tolerant operation is proposed to maintain the output current, internal dynamics, and switching harmonics unchanged after the faulty submodule is bypassed. This is achieved by resetting the period and phase registers in the local controller according to the information of bypassed submodules. The control loops of the MMC are not influenced by the proposed fault diagnosis and fault-tolerant operation, making the operation transition seamless and reliable. Experimental results show that fault identification and system reconfiguration can be completed within 5 ms, and the MMC can seamlessly and smooth ride through the switch open-circuit faults without severe malfunction and catastrophic damages. [ABSTRACT FROM AUTHOR]

Conventional centralized control strategies may reduce the flexibility and expandability of a modular multilevel converter (MMC) system. To tackle this issue, this paper proposes a distributed control architecture that is capable of assigning certain control tasks to distributed local controllers and improves the modularity of an MMC system. A central controller dealing with the output current regulation based on sensed arm currents is adopted. The control of MMC internal dynamics and the pulsewidth modulation (PWM) generation are distributed into local controllers. Unlike the conventional MMC control that needs all submodule capacitor voltages for capacitor voltage averaging, the proposed capacitor voltage control only relies on local submodule voltage measurement. Consequently, communication-intensive capacitor voltage transmission in each control cycle is not required and the communication burden of the control system can be significantly reduced. The control loops and possible control conflicts among submodules are presented and considered for system stability analysis. The effectiveness of the proposed distributed control architecture and capacitor voltage control for an MMC are confirmed by the start-up, steady state, and transient experimental results. [ABSTRACT FROM PUBLISHER]

The stability of dual active bridge converter (DAB) is threatened when feeding the constant power loads (CPLs). This article proposes a deep reinforcement learning-based backstepping control strategy to solve this problem. First, a nonlinear disturbance observer is adopted to estimate the large-signal nonlinear disturbance. Then, a backstepping controller is used to stabilize the voltage response of the DAB under the large-signal disturbance. Finally, a compensation method based on deep reinforcement learning is developed to intelligently minimize output voltage tracking error and improve the operating efficiency of the system. The proposed controller can guarantee system stability under the large-signal disturbance of the CPL and achieve a fast dynamic response with accurate voltage tracking; it is more adaptive by using the deep reinforcement learning technique through the learning of its neural networks. The effectiveness of the proposed controller is verified by experiments. [ABSTRACT FROM AUTHOR]

Economic operation is a major concern for microgrids (MGs). System operation cost is optimized when the incremental costs (ICs) of all distributed generators (DGs) reach equality. Conventionally, economic dispatch of DGs is solved by centralized control with optimization algorithms or distributed control with consensus algorithms. To improve the reliability, scalability, and economy of MGs, a fully decentralized economic power sharing strategy is proposed in this paper. As frequency is a global state in ac MG and dc bus voltage serves as a natural indicator in dc MG, a frequency-IC droop scheme is proposed for ac MG, a voltage-IC droop scheme is proposed for dc MG, and a normalization scheme is proposed for hybrid ac/dc MG. By using the proposed technique, ICs of DGs reach equality with the convergence of the system global indicator (frequency or dc bus voltage). Then power sharing of each DG is automatically achieved based on its relevant IC function and the total operating cost can be optimized without any communication or central controllers. The proposed approach is implemented in an ac MG, a dc MG, and a hybrid ac/dc MG in MATLAB/Simulink to verify its effectiveness. [ABSTRACT FROM AUTHOR]

This study proposes an advanced current control strategy for three-phase grid-connected inverters to reject the impact of the dc offsets and scaling errors in the grid voltage measurement on the grid current performance. The proposed current controller designed in the synchronous (d-q) reference frame is developed with a proportional integral (PI) plus three vector PI controllers. The PI controller regulates the fundamental current to follow its reference, meanwhile, three vector PI controllers tuned at the fundamental grid frequency ( \omega _s), 2\omega _s, 6\omega _s are employed to eliminate the dc, unbalance, harmonic components in the grid current. As a result, the three-phase grid currents are controlled to be balanced, sinusoidal, and extremely low dc component despite the presence of the dc offset and scaling errors in the grid voltage measurement and distorted grid voltage conditions. The main advantage of the proposed control scheme is that it is developed without the need of additional hardware circuit, dc extraction, and harmonic detection scheme so that it can be integrated into the existing grid-connected inverter system without extra cost. The effectiveness of the suggested solution is verified by experimental results under various grid voltage conditions and the grid voltage measurement errors. [ABSTRACT FROM PUBLISHER]

Although smart home has received wide attention in recent years, numerous scholars focus more on energy optimization strategy than energy dispatch hardware device (named energy router). Meanwhile, this energy router should have several features, i.e., high renewable energy utilization, energy multi-port and low volume. Thus, this paper designs a nine-port energy router regarding smart home and proposes a multimode hierarchical management strategy for this energy router. First, for the multi-port demand of wind, solar, storage and utilization, this paper presents a nine-port energy router to improve the renewable energy consumption and power supply flexibility. In addition, to reduce the volume of the energy router, a non-isolated AC/DC hybrid topology is constructed through embedding the integrated power electronic converters, which achieves the miniaturization of the energy router. In order to improve the renewable energy utilization rate, the decentralized module control is proposed for the components of energy router to provide the voltage and frequency support for system, and realizes the power sharing of distributed generations (DGs). Furthermore, the power exchange control with three-mode switching is proposed to guarantee the global energy flow balance under complex conditions. Eventually, the feasibility of the energy router is verified by the simulation and experiments. [ABSTRACT FROM AUTHOR]

Distributed renewable energy source is an advisable solution for dc microgrids to reduce fuel consumption and CO2 emission. In such microgrids, the installation of two or more battery energy storage (BES) units is utilized to compensate the power imbalance between the sources and loads. Nevertheless, energy management with numerous BES units does not simultaneously consider the impacts of distributed generators (DGs) and constant power loads (CPLs). Since the inaccurate current sharing will shorten the lifetime of the batteries and cause instability problem, this article proposes a distributed secondary $H_{\infty }$ consensus approach based on the dynamic event-triggered communication method to realize accurate current sharing and efficient operation in the presence of numerous DGs and CPLs. First, the whole state-space function model of the dc microgrid consisting of DGs, batteries, resistive loads, and CPLs, is first built in detail. This model is further transformed into standard linear heterogeneous multiagent systems, which provides an indispensable preprocessing for advanced control strategy application. Then, the distributed secondary $H_{\infty }$ consensus approach based on the foresaid systems is designed to achieve accurate current sharing. For reducing the communication among batteries and the controller updating frequency, the dynamic event-triggered communication method is proposed. Compared with existing event-triggered methods, the communication and controller updating frequency of the proposed dynamic event-triggered method have been reduced a lot. Additionally, the proposed method can not only avoid the Zeno behavior, but also obtain the lowest bound of the sampled time interval. Finally, the numerical simulation results and experimental results verify the effectiveness of the proposed control strategy. [ABSTRACT FROM AUTHOR]

State-of-charge (SoC) imbalance and bus voltage deviation are two of the main problems in autonomous dc microgrids. Based on this concern, this paper presents an improved dual-quadrant SoC weighted control strategy and a distributed optimization control method to achieve SoC balance, ensuring accurate power-sharing and bus voltage recovery. Firstly, this paper couples the injected/released power with the current SoC and observed average SoC value to weight the droop coefficient, which is based on the charge/discharge mode for the energy storage system. Then a secondary controller is designed based on distributed optimal control to eliminate the bus voltage deviation caused by the line impedance difference. The proposed optimal control method optimizes the average bus voltage to the nominal value and achieve accurate power-sharing by constructing the correlated variables and voltage independent intermediate variables exchanged among bulk energy storage units (ESUs). Since the voltage observer cannot accurately observe the true average bus voltage under the communication delay, the proposed distributed optimal control method without the voltage observer can ensure that the average bus voltage is optimized to the nominal value, thus improving the robustness of the control system. Finally, the correctness and effectiveness of the proposed method are verified in Simulink/MATLAB. [ABSTRACT FROM AUTHOR]

Renewable energy is an advisable choice to reduce fuel consumption and $\rm CO_{2}$ emission. Therein, wind energy and solar energy are the most promising contributors to reach this goal. Although the hybrid wind/solar system has been widely studied, the real-time current sharing based on their maximum capacities is rarely achieved in terms of seconds. Based on this, this paper proposes an accurate current sharing and voltage regulation approach in hybrid wind/solar systems, which is based on distributed adaptive dynamic programming approach. Firstly, the equivalent wind/solar model is built, which is an indispensable preprocessing to achieve the complementary between wind energy and solar energy. Therein, the wind energy and solar energy can output relative current according to their respective capacity ratio, which ensure the maximum utilization ratio of renewable energy source. Furthermore, current sharing and voltage regulation problem is switched into optimal control problem. Under this effect, each source agent aims to obtain the optimal control variable and achieve accurate current sharing/voltage regulation. Moreover, an adaptive dynamic programming approach based on Bellman principle is proposed. It can achieve accurate current sharing and voltage regulation. Finally, the simulation results are provided to illustrate the performance of the proposed adaptive dynamic programming approach. [ABSTRACT FROM AUTHOR]

Multiple-voltage-region control, in which the bus-voltage range is divided into several regions, is usually implemented for dc microgrid operation in distributed manner. Voltage/power droop relationships are imposed for active power sharing among slack terminals. Conventionally, threshold voltages for voltage region partition are determined with fixed percentage of variation around the nominal value, which may result in unevenness of droop coefficients in different regions. If system droop coefficient is too high, significant bus-voltage step change due to load variation will occur. On the other hand, significant power sharing error among slack terminals will be induced if the droop coefficient is too low. In this paper, a compromised solution with power-capacity-based bus-voltage region partition is proposed to equalize the droop coefficients in different regions. However, the droop coefficients are determined based on the rated power capacity of system units. Bus-voltage discontinuity appears when the power capacity reduces in actual implementation. To eliminate the voltage discontinuity, online droop coefficient tuning according to the real-time power capacity is implemented. Algorithms for local power capacity estimation of solar photovoltaic (PV) and battery energy storage have been proposed. A lab-scale dc microgrid has been developed for verification of the proposed methods. [ABSTRACT FROM AUTHOR]

Modular multilevel converters (MMCs) in high-voltage dc applications usually adopt a distributed control architecture to manage a large number of submodules (SMs) through a communication network. The communication congestion and network disconnection might lead to communication interruption (CI) and eventually cause the system to malfunction. In this article, a resilient operation strategy is proposed and studied to ride-through the CI fault, in order to prevent frequent fault SM bypassing, replacement, or even system shutdown. The analysis of the MMC distributed control system with the presence of CI indicates that the insertion index of the faulted SM might become constant, which distorts the output current and results in overvoltage of the communication interrupted SM (CI-SM). The CI-SM capacitor voltage prediction can be used to determine the MMC safe operation period after CI occurs. During the safe operation period, the CI-SM power balance is sustained by utilizing prestored phase signals to generate a sinusoidal insertion index according to its capacitor voltage tracking error. Two operation modes are proposed and analyzed to ensure the MMC stable operation under various conditions. The system protection is sensibly used only if the CI duration exceeds a safe operation period, which avoids frequent SM cut-off. Good agreement of the CI-SM capacitor voltage is achieved between the theoretical and simulation results. The effectiveness and robustness of the proposed MMC resilient operation are experimentally confirmed. [ABSTRACT FROM AUTHOR]

This article proposes a circulating current and second harmonic current (SHC) suppression method by introducing virtual impedance into the circulating current and output current feedback control loops of the dc solid-state transformer (DCSST). The virtual impedance is employed to adjust impedance in the circulating current feedback control loop to decrease the circulating current when the transmission efficiency of each dual active bridge is different. And a SHC suppression method, which introduces the virtual impedance containing a bandpass filter, is adopted to reduce the SHC and improve the dynamic performance of the DCSST. Moreover, a relatively independent modular control method, which is conducive to the modular expansion of the DCSST, is proposed. Compared with traditional DCSST control methods, the proposed method can simultaneously realize the output current sharing and effectively reduce the SHC with modular control. Finally, a DCSST prototype is built and the results of the experiment verify the validity and effectiveness of the proposed control strategy and solutions. [ABSTRACT FROM AUTHOR]

A decentralized improved I-V droop control strategy for battery-supercapacitor (SC) hybrid energy storage system (HESS) is proposed in this paper. The dynamic power sharing between battery and SC is realized by replacing the constant droop coefficient in I-V droop control with virtual impedance, i.e. virtual inductance for battery side converter and virtual resistance for SC side converter. Besides, by injecting the virtual inductance in the battery side converter, negligible DC bus voltage deviation can be achieved without extra voltage compensator. Moreover, the state-of-charge (SoC) recovery is also considered to extend the service life of the HESS. Furthermore, in the proposed regulated power system, since the power allocation, DC bus stability and SoC recovery are decoupled from each other, the design of control parameters is simple. The corresponding design guideline is demonstrated in this paper. Finally, to verify the accuracy and feasibility of the theoretical analyses, hardware in the loop simulations have been conducted. [ABSTRACT FROM AUTHOR]

Indirect matrix converter (IMC) is an alternative for ac/ac energy conversion, usually operated with a voltage stepped-down gain of only 0.866. For applications like distribution generation where voltage-boost functionality is required, the traditional style of operating the IMC is therefore not appropriate. Like most power converters, the operation of the IMC can surely be reversed to produce a boosted gain, but so far its relevant control principles have not been discussed. These challenges are now addressed in this paper with distributed generation suggested as a potential application. Simulation and experimental results for validating various performance aspects of the proposed control schemes can be found in a later section of this paper. [ABSTRACT FROM AUTHOR]

In dc microgrid, energy storage system (ESS) plays a crucial role to provide short-or-long term and high-quality electric energy. The different control strategies for bidirectional dc-dc converter (BDC) of ESS in grid-tied and islanded modes pose challenges to the coordination control of the dc microgrid. This paper proposes an autonomous control scheme for the BDC in dc microgrid. The proposed control scheme is based on $V^2-P$ droop control and unifies bus voltage regulation and power regulation in a single control structure. Thus, global smooth transition between various operation modes can be achieved without any control strategy changes, which avoids various mode switch detection mechanisms and improves system stability. Furthermore, the proposed control scheme is fully decentralized which reduces the reliance on communication, and enhances the reliability of the microgrid. On the other hand, $V^2-P$ droop approach eliminates the negative effect of widespread constant power loads (CPLs) in dc microgrid. The stability of the proposed control method is illustrated, and the design guideline of some critical control gains is addressed. Finally, the effectiveness of the proposed control scheme is validated by the real-time hardware-in-loop (HIL) platform. [ABSTRACT FROM AUTHOR]

In this paper, a modified one-cycle-control (OCC) scheme is proposed for regulating three-phase pulsewidth-modulated (PWM) rectifiers operating under unbalanced and distorted supply conditions. Mathematical analysis is first presented to show the dominant harmonic-voltage components appearing across the dc link of the PWM rectifier when it is controlled by an existing OCC scheme. Such dc-link harmonics when produced may aggravate harmonic currents flowing into the input terminals of the three-phase rectifier. To address these interrelated unbalance and harmonic concerns, the concept of reconstructing the appropriate reference signals in the OCC control core is introduced, before modifications are recommended for altering the key control equation. The improved OCC controller eventually developed is proven to exhibit minimal input-current distortion and a smoother dc-link voltage without using large capacitance. Other advantages exhibited by the traditional OCC scheme, such as no phase-locked loop, no frame transformation, and constant switching frequency, are also retained by the improved controller, whose theoretical findings are fully verified by experimental results obtained from a 1.2-kW three-phase PWM rectifier built in the laboratory. [ABSTRACT FROM PUBLISHER]

The hybrid fuel cell/supercapacitor (FC/SC) system is a promising onboard power supply system for more electric aircraft (MEA), where system stability is a critical issue due to the high penetration of constant power loads (CPLs) in MEA. This article proposes a composite finite-time controller for decentralized power sharing and stabilization of the hybrid FC/SC system with CPLs. It consists of an integral droop (ID) + finite-time controller for the SC converter and a proportional droop (PD) + finite-time controller for the FC converter. First, the coordination of PD and ID achieves decentralized power sharing between FC and SC such that SC only compensates fast fluctuations and FC provides smooth power at the steady state. Then, a finite-time observer is designed to provide feedforward compensation for the disturbances and enables accurate tracking with fast dynamics. Finally, a composite finite-time controller is constructed following a nonrecursive synthesis procedure with a rigorous large signal stability analysis. The proposed controller guarantees finite-time convergence even under large signal variations and can be easily implemented with a practical gain tuning procedure. Simulations and experiments are conducted to verify the proposed technique. [ABSTRACT FROM AUTHOR]

This article investigates the current sharing and voltage regulation problem of a DC microgrid by a distributed supervisory control method. In the existing secondary control methods, current sharing feedback control loop and voltage regulation feedback control loop are linearly integrated to shift the droop equation. However, the linear combination of two loops may easily offset the control effect of each other, as the control dimension is less than the objective dimension. This fact motivates us to design a distributed supervisory secondary control (DSSC) scheme to achieve a more flexible configuring of each converter. The DSSC consists of two candidate controllers and a supervisor. The two controllers refer to current sharing configuring and DC bus voltage regulation respectively, and the supervisor is to orchestrate the switching between candidate controllers based on the system environment of DC microgrid. Under the proposed DSSC, each converter selects to configure the current sharing or regulates the DC bus voltage according to its need. Theoretical stability analysis is rigorously conducted. Finally, both simulation and experiment results are presented to demonstrate the effectiveness of DSSC. [ABSTRACT FROM AUTHOR]

The penetration level of photovoltaic (PV) keeps increasing in modern distribution networks, which leads to various severe voltage limits violation problems. This article aims to aggregate and utilize the PV inverters for voltage regulation by a fully distributed two-level Volt/VAr control (VVC) scheme. In the lower-level VVC (real-time scale), the rooftop PV inverters are aggregated via consensus algorithms and then governed by droop controllers in medium-voltage networks. The droop controller adjusts the reactive power output of each PV aggregator in real-time from its dispatched value depending on the bus voltage variations. In the upper-level VVC (15-min timescale), the reactive power of PV aggregators is dispatched for power loss minimization, where control signals are set as base values for PV aggregators. This problem is formulated as second-order cone programming and solved by the alternating direction method of multipliers. The simulation results demonstrate the effectiveness of the proposed method in both short-term and long-term scenarios with different system scales. [ABSTRACT FROM AUTHOR]

In this article, a fixed and smooth-switch-sequence modulation strategy is proposed to equalize the dc-link voltages among the cascaded rectifier. The structure of a single-phase three-level neutral-point-clamped cascaded rectifier is studied. Three core steps of this strategy are analyzed respectively, including carrier wave disposition calculation, fixed pulse generator, and voltage rank function. In addition, a criterion of the degree of the load unbalance is established in order to measure the voltage balancing boundary of the presented approach. The superiorities of the proposed control strategy embody the smooth switch sequence, the strong voltage balance capability, as well as the fixed switch sequence. Owe to these advantages, the cascaded rectifier could effectively reduce the switching frequency, achieve the goals of voltage balancing, and reduce the calculation burden of the controller when the number of cascaded modules is large. The effectiveness of the proposed strategy is verified by simulation and experiment results. [ABSTRACT FROM AUTHOR]

Power loss and voltage regulation are two fundamental and challenging issues in DC distributed generation system. In this paper, a multi-objective optimization problem is established to achieve trade-offs between reducing power loss and decreasing voltage deterioration by adjusting the weighting coefficients. This problem is proven to be a convex optimization under constant impedance load and constant current load. A distributed algorithm based on random coordinate descent method is developed to solve this problem without acquiring the information of line impedance. Thus, the optimal operating point of the system can be found automatically in real-time, and the deviation of optimal solution caused by the fluctuation of network parameters is avoided. In addition, the complexity of this algorithm is low and its computational requirement is reduced in practice. Finally, case studies are implemented to verify the effectiveness of the proposed algorithm under the scenarios of line parameter fluctuation, load variation, communication line failure, and plug-play capabilities. [ABSTRACT FROM AUTHOR]

This paper introduces a novel H-bridge structured ac–ac pulsewidth modulation (PWM) converter topology based on two-level non-differential ac chopper legs, which can work at the non-inverting and inverting modes for the utility voltage compensation. Compared to the traditional bipolar-type H-bridge ac–ac converter, no bidirectional switches are switched in a complementary manner to overcome the commutation problem due to the delayed response of electronic circuits and semiconductor switching devices. The detailed PWM control signals and operational principles are presented to regulate the output voltage in a bipolar manner. Especially the main advantage is that the proposed ac–ac converter has the same buck/boost operation process for non-inverting and inverting modes, which ensures the continuously average current supply to the low-voltage output side without a high-value capacitor to support power. Additionally, due to the common sharing ground of the input and output, the feature that output can reverse or maintain phase angle with input is supported well. Then, the detailed analysis, design conditions, and experimental verification based on a 1 kW experimental prototype are presented. [ABSTRACT FROM AUTHOR]

This paper introduces a compensation strategy to deal with both current and voltage measurement errors in the three-phase pulsewidth modulated rectifier system. The dc offset and scaling errors in the voltage and current measurements cause the injection of undesired dc and unbalanced currents into the three-phase input current and subsequently lead to voltage ripple at the dc output voltage. This paper proposes a compensation scheme for current measurement error where the dc offset and scaling errors in the current measurement are estimated from the characteristic of the dc output voltage ripple combining with simple band-pass and low-pass filters. Meanwhile, an advanced current controller designed with a proportional integral plus two resonant controllers tuned at the fundamental grid frequency $({{\omega _s}})$ and $2{\omega _s}$ in the synchronous (d–q) reference frame is suggested to reject the impact of the dc offset and scaling errors in the voltage measurement. The proposed compensation method is developed without the need of extra hardware circuit, sensor, or precise information of system parameters so that it can be considered as more cost-effective and robust solution. The effectiveness of the proposed solution is verified by experimental results. [ABSTRACT FROM AUTHOR]

CLLC-type dc transformer (CLLC-DCT) is very popular in the hybrid ac–dc microgrid thanks to its high-power density advantage and good bidirectional power transfer capacity. In the hybrid ac/dc microgrid, the open-loop control is always utilized by the CLLC-DCT to cooperate with the bidirectional interlinking converter to realize the power and voltage conversion between the ac and dc bus. This paper first studies the circuit parameters design of the open-loop controlled CLLC-DCT with consideration of such a realistic problem: The real inductors/capacitors values are actually different with their theoretically designed values due to the operation power and temperature variation. To solve this problem, a robust circuit parameters design scheme is proposed for the CLLC-DCT in this paper. With the proposed scheme, the designed CLLC-DCT exhibits good power transmission and voltage regulation ability in the hybrid ac/dc microgrid even when its actual inductors/capacitors values vary with the practical power and temperature. The robust design method is experimentally verified in a hybrid ac/dc microgrid prototype. [ABSTRACT FROM AUTHOR]

A high-performance three-phase pulse width modulation (PWM) converter with reduced dc-link capacitor under unbalanced ac voltage conditions is proposed in this paper. The unique feature of the converter lies in that sinusoidal symmetrical ac currents and ripple free dc voltage can be achieved simultaneously without using a bulky capacitor, which was thought to be a dilemma in the past. The control scheme is implemented in an α–β frame, so the complex rotate transformations are avoided, and it does not require the extraction of positive and negative sequence currents, which simplifies the control algorithm. A two-quadrant operation active power compensator together with its controller is developed to suppress the voltage ripple in the dc-link. Compared with the passive compensation method, the compensator is equipped with a smaller capacitor to reduce the system size, weight, and cost. Moreover, the compensator could be integrated with the conventional three-phase three-leg PWM converter seamlessly. The effectiveness of the proposed control schemes is verified by the experiment results. [ABSTRACT FROM PUBLISHER]

The traditional finite-control-set model predictive control (FCS-MPC) method for a cascaded H-bridge (CHB) rectifier has two main issues: heavy computational burden and low steady-state current performance. In this paper, a novel FCS-MPC method has been proposed for a single-phase CHB rectifier. The proposed method solves the optimization problem of FCS-MPC for one cell by one cell, like a “pipeline.” In the proposed method, the sampling period is divided into equal intervals by the number of cells. At the beginning of the first interval, the first cell selects its switching state to be applied. Then, the following cell selects its switching state to be applied at the beginning of next interval. Finally, the selected switching state of last cell will be applied at the beginning of the last interval. A cost function presenting the control objectives of common source current error and itself dc-link voltage error is evaluated for each cell. A single-phase three-cell CHB rectifier controlled by a DSpace DS1104 is tested and the experimental results show that a significant reduction in computational time, an improved steady-state current performance, and a comparable dynamic response are achieved in the proposed method in comparison with the traditional FCS-MPC method. [ABSTRACT FROM AUTHOR]

This paper proposes a modified one cycle control (OCC) for active power filter (APF) to compensate only harmonic components of load currents. The conventional OCC-based APF cannot differentiate between the harmonic and reactive components of load currents, which leads to the increment in device current rating because of compensation of large reactive currents besides harmonics. The reference signals of the OCC control core have been reconstructed and the associated control equations have been developed, following the control philosophy of simplicity. The modified scheme is easy to implement and only three more sensors are required for measuring load currents compared with the conventional OCC. This modified OCC guarantees the excellent performance of harmonic compensation alone and retains the advantages of the conventional OCC, such as no phase locking loop and the constant switching frequency. The feasibility and performance of the proposed OCC has been validated by experimental studies on a 5 kVA APF hardware platform developed in laboratory. [ABSTRACT FROM PUBLISHER]

For hybrid energy storage system in dc microgrid, effective power split, bus voltage deviation, and state-of-charge (SoC) violation are significant issues. Conventionally, they are achieved by centralized control or hierarchical control methods with communications. This paper proposes a simple and effective strategy to solve the problem in a decentralized manner. A high-pass filter-based droop (HPFD) controller is proposed to regulate the battery converter, and a virtual capacitance droop (VCD) controller is implemented for a supercapacitor (SC) converter. The cooperation of HPFD and VCD first achieves autonomous power split that high-frequency fluctuation is buffered by SC and low-frequency power is supplied by battery. Meanwhile, the bus voltage deviation induced by the droop-based power sharing is eliminated automatically at steady state. The resulted bus voltage restoration simultaneously enforces SC SoC back to its nominal value, and, thus, ensures continuous operation of SC as a power buffer without the violation of its SoC boundary. A design guideline is developed to ensure expected system dynamics. The effectiveness of the proposed method and analytical results are validated by simulations and experiments. [ABSTRACT FROM PUBLISHER]