Search

In this article, a new dual-permanent magnet spoke-type flux-reversal machine (dual-PM SFRM) for direct-drive applications is proposed. Tangentially magnetized permanent magnets (PMs) sandwiched with iron poles are set in stator slots. To increase the torque density within the geometric restrictions, PMs are introduced in the rotor as well and magnetized radially to form a consequent-pole rotor. Global optimizations are conducted and comparisons are made on torque, torque ripple, and torque/PM volume with the existing single-PM SFRM. It is found that the proposed dual-PM SFRM can produce 22.6% larger torque with an optimal PM volume and a 17.5% larger torque with the same PM volume compared with the single-PM counterpart. Moreover, major magnetic field space harmonics are derived analytically and verified by finite-element analysis (FEA) and the torque components produced by the working harmonics are calculated and compared in terms of different stator/rotor pole number combinations. Comparisons are made on back electromotive force, cogging torque, torque performance, and efficiency between dual-PM SFRM and conventional flux-reversal machine. The influence of different stator configurations, i.e., the slot opening, the iron bridge, and the unequal tooth, on torque performance in the proposed dual-PM SFRM has been studied and highlighted. A prototype has been built and tested to validate the FEA calculations. [ABSTRACT FROM AUTHOR]

Consequent-pole (CP) permanent magnet (PM) configuration suffers asymmetric electromagnetic characteristics although it saves PM usage. The CP-based stator-PM synchronous machines are investigated in this paper, with particular reference to symmetrical issues. The electromagnetic performances of the CP-based stator-PM synchronous machines are firstly evaluated. Afterwards, the rule of even order harmonics cancellation is presented for different slot/pole number combinations and winding layouts, based on which symmetrical phase flux-linkages can be obtained although the unbalanced magnetic flux naturally occurs. Moreover, based on the three-dimensional finite element analysis, the unipolar end leakage-flux caused by the asymmetric magnetic field is identified, and the risk of the shaft magnetization is revealed. Finally, a pair of prototype machines are fabricated and measured to validate the analyses. [ABSTRACT FROM AUTHOR]

The control performance of Hall sensor-based high-speed brushless dc (BLdc) motor drives depends heavily on the accuracy of Hall sensor signals. Due to the existence of Hall signal errors, the system may operate under unbalanced conditions that will lead to asymmetric currents and high-torque ripple. For high-speed BLdc drive, using voltage source inverter (VSI) with the pulsewidth modulation (PWM) technique will also lead to PWM update delay that causes inaccurate commutation. In this article, two Hall signal errors, i.e., misaligned and uneven Hall signal errors, are investigated and a Hall signal balancing strategy is developed to detect Hall signal errors and regenerate balanced Hall signals. A novel PWM generation scheme is then proposed to eliminate the PWM update delay when using traditional VSI. Both simulation and experiment results have verified the effectiveness of the proposed strategy. [ABSTRACT FROM AUTHOR]

Voltage induced in the dc winding by the armature field in wound field switched flux (WFSF) machines will induce voltage perturbation in the voltage supply and cause dc winding current ripple and field excitation fluctuation. This will challenge the dc voltage controller and deteriorate the control performance, especially when the load and/or the rotor speed are high. In this article, the dual three-phase armature winding design with a phase-shift of 30 electrical degrees is employed in the partitioned stator WFSF machines to reduce the on-load dc winding-induced voltage. Analytical deductions and finite element (FE) results demonstrate that the dominant sixth-order-induced voltage harmonic can be suppressed to zero. Hence, the peak-to-peak induced voltage in the 12/11- and 12/13-pole partitioned stator WFSF machines can be reduced by 83.35% and 82.53%, respectively. Due to the improvement of winding factors, the torque densities are 4.85% and 5.60% higher, respectively. Prototypes are built and tested to verify the analytical and FE results. [ABSTRACT FROM AUTHOR]

Asymmetric interior permanent magnet (AIPM) rotor topologies can achieve torque enhancement in IPM synchronous machines without the increase of PM usage due to utilizing magnetic-field-shifting (MFS) effect by reducing the current angle difference between maximum PM and reluctance torque components. This paper investigates the influence of armature reaction on MFS effect in AIPM machines. A general model of IPM machines considering MFS effect is analytically developed and the AIPM and IPM machines using the same stator, rotor diameter and total PM amount are comparatively studied. It shows that the armature reaction affects the MFS effect in both AIPM and IPM machines and the influence is more significant in AIPM machine. The relationships between MFS effects in PM flux-linkage and inductance characteristics and current angles for maximum PM and reluctance torque components are revealed. It confirms that the change of current angles of torque components is due to the MFS effect in PM flux-linkage and inductance characteristics in both AIPM and IPM machines. Besides, the developed machine model considering MFS effect is verified by finite element analysis. Finally, a small-scale AIPM machine prototype is fabricated and measured to validate the finite element analysis. [ABSTRACT FROM AUTHOR]

In this paper, a high-speed permanent magnet (HSPM) motor having 6-slot/2-pole (6s/2p) number combination and 2 coil-pitch windings are developed for domestic appliance application. Two HSPM motors with different layouts of 2 coil-pitch windings are optimized and their electromagnetic performances are evaluated. The best winding configuration is then identified for shorter motor axial length and larger torque density. Since 3-slot/2-pole (3s/2p) HSPM motors with non-overlapping windings have the same winding factor, a comparison between 3-slot and 6-slot motors is also conducted, particularly for torque density, losses, and unbalanced magnetic force (UMF). It shows that 6s/2p PM motors with 2 coil-pitch windings are suitable for high-speed application without UMF and less rotor PM loss. Finite element predicted electromagnetic performances are validated by experiments made on two prototype motors. [ABSTRACT FROM AUTHOR]

Consequent-pole (CP) permanent magnet (PM) machines have attracted considerable interest as a means of reducing machine cost through a marked reduction in the volume of PM required to meet a particular torque specification. However, the presence of a large torque ripple that can result from the CPPM structure can hinder their adoption in some applications, especially for the dominant third-order torque ripple. Although several design-specific modifications have been proposed to ameliorate torque ripple, the generalized principles underpinning this behavior have not been fully established. In this article, it will be illustrated that an aggregation of the fluctuations in inductance, back electromotive force, and cogging torque contributes to increased torque ripple. Meanwhile, an asymmetric pole shaping method is proposed to reduce the torque ripple, taking the dominant third-order torque ripple as an example. Both simulated and experimental results of the 12-slot/8-pole prototypes show that compared to the symmetrical pole shaping model and the plain pole model, the proposed asymmetric shaping method is effective in reducing torque ripple. [ABSTRACT FROM AUTHOR]

Consequent pole (CP) permanent magnet (PM) machines offer scope for reducing the quantity of PM material and hence cost compared to more conventional PM machine topologies of the same rating. In this type of machine, the rotor pole arc is usually optimized to realize the largest output torque with pole shaping methods used to reduce torque ripple. However, such approaches tend to be limited by constraints imposed on the pole shapes. It is a common practice to adopt similar PM and iron pole shapes, an approach that does not fully account for the different characteristics of PM and iron poles in CPPM machines, often leading to large even order harmonics in the airgap flux density. This article proposes a shaping method with a variable rotor profile and pole arc span being established by means of optimization by Genetic Algorithm. It is demonstrated that for a fixed quantity of PM material, different PM and iron pole shapes in combination with optimal PM and iron pole arc spans are essential for ensuring both maximum output torque and lower torque ripple when the due account is taken of flux leakage. It also demonstrates that since the flux density in the region under a PM pole is governed by the magnetic potential produced by magnets while it is governed by magnetic reluctance under iron pole, different PM pole and iron pole shapes are necessary to reduce the even-order harmonics in a CPPM machine and consequently to reduce torque ripple. The performances of optimized and more conventional CP machines are compared by finite-element method on 12-slot/8-pole prototype motors. [ABSTRACT FROM AUTHOR]

In this article, an online rotor position error correction method is proposed to eliminate the impact of parameter mismatch in sensorless control for dual three-phase (DTP) permanent magnet synchronous machines drives. The rotor position error production mechanism is first derived and shows that the error changes with the trend of current variation when there is a parameter mismatch. Based on this mechanism, by injecting sinusoidal current signals with low frequency and small amplitude into both sets of three-phase windings, the presence of parameter mismatch and its level can be revealed from the corresponding sinusoidal responses of the estimated speed of sensorless observers, which do not depend on the inertia of the machine. Since the amplitudes of these responses decrease as the parameter mismatch level reduces, with the help of the least mean square algorithm, the parameters can be adaptively adjusted to the actual values, and the position error can be thus corrected. Moreover, with the extra freedom of DTP machines, the detrimental effects on torque production due to current signal injections can be eliminated through adjusting the phase between the two injected signals. The effectiveness of the proposed method has been validated through simulation and experimental results. [ABSTRACT FROM AUTHOR]

This article proposes and investigates two asymmetric consequent-pole hybrid excited flux reversal machine (AS-CP-HEFRM) topologies, which have same numbers of iron poles and permanent magnets (PMs) with concentrated ac and dc windings on each stator pole and a salient pole rotor. If PM number on one stator pole is larger than 1, PMs are magnetized radially in the same direction on one stator pole, while opposite on adjacent stator poles. The phenomenon of the phase shift between the flux linkages of dc and PM excitations in the AS-CP-HEFRMs is revealed for the first time, which will weaken the regulation of dc excitation field to PM produced field. The elimination condition of the phase shift is derived and verified by finite-element analysis in this article, which can be considered as design guidelines in AS-CP-HEFRMs. Airgap magnetic field space harmonics of AS-CP-HEFRM are also investigated and verified by finite-element analyses. Meanwhile, the relationship between the rotor pole number and the stator pole arc (PM ratio) is derived and verified by global optimization based on genetic algorithm for maximum average torque. The influence of stator/rotor pole number combinations is also studied and compared in terms of torque, torque ripple, and flux regulation capability. The torque components produced by airgap magnetic field space harmonics are calculated and compared. A prototype has been built and tested to validate the finite element calculations. [ABSTRACT FROM AUTHOR]

This article proposes a novel asymmetric interior permanent magnet (AIPM) rotor topology that has a mixed V-shape and spoke-type PM configuration, designated as a 1.5-layer PM structure, and asymmetric arrangement of V-shape PMs and asymmetric flux barriers. The AIPM rotor topology is employed for IPM synchronous machines to utilize the magnetic-field-shifting (MFS) effect for increasing average torque by reducing the current angle difference between peak PM and reluctance torque components. Three machines, i.e., the proposed 1.5-layer AIPM, a symmetrical 1.5-layer IPM-I, and a conventional V-shape benchmark IPM-II are designed and optimized using the same stator, rotor diameter, and total PM usage by global parametric optimization considering the mechanical stress. The effect of asymmetric features of the 1.5-layer AIPM rotor design, i.e., asymmetry of V-shape cavity as well as position and dimensions of flux barrier, on maximum torque and open-circuit air-gap field are investigated. The electromagnetic performances of three machines are compared. It confirms that the proposed AIPM machine has the highest maximum torque and the smallest cogging torque simultaneously. It is also revealed that the torque enhancement is achieved by both the 1.5-layer structure and MFS effect. Finally, a prototype of an AIPM machine is manufactured and tested to validate the analyses. [ABSTRACT FROM AUTHOR]

This article proposes a novel asymmetric interior permanent magnet (AIPM) rotor topology for torque enhancement and torque ripple reduction in IPM synchronous machines. The AIPM rotor structure is featured by a hybrid-layer permanent magnet configuration, i.e., for each pole, a part of PM configuration has one-layer while the other part has two layers. It allows the magnetic-field-shifting (MFS) effect to be utilized by reducing the current angle difference between maximum PM and reluctance torque components, thereby effectively increasing the maximum resultant torque. The proposed AIPM machine and a conventional V-shape IPM machine are designed and globally parametric optimized with the same 24-slot/4-pole stator, rotor diameter, and PM usage. The influence of key rotor geometric parameters of the AIPM machine on torque and open-circuit air-gap magnetic field characteristics are investigated. The comparison of electromagnetic performance confirms that significant torque enhancement and torque ripple reduction in the AIPM machine compared with the conventional V-shape IPM machine and reveals the MFS effect is essential for torque increase. Finally, an AIPM machine is manufactured and tested for validation. [ABSTRACT FROM AUTHOR]

In this article, three 6-slot/2-pole high-speed permanent magnet motors with 1, 2, and 3 coil-pitch windings are optimized by the finite element method taking into account stator copper loss and iron loss. Their electromagnetic performances are analyzed and compared, including air-gap flux density, back electromagnetic force, electromagnetic torque, winding inductances, and various loss components. For high-speed application, compared with 1 and 3 coil-pitch windings, the proposed 2 coil-pitch windings have a good tradeoff between winding factor and end-winding axial length which are attractive for improved torque density. Finally, the experimental results are given to validate some of the finite element predicted results. [ABSTRACT FROM AUTHOR]

In this article, we propose a novel switching-table-based direct torque control (ST-DTC) method to eliminate the current harmonics in dual-three-phase permanent-magnet synchronous machines due to the back electromotive force (back EMF) harmonics and voltage vector selection. By employing a novel space voltage vector selection strategy and the optimal action time for different groups of vectors, a novel ST-DTC method is developed. Furthermore, in order to implement standard pulsewidth modulation (PWM) switching sequence, a centralization PWM method for 36 voltage vectors is introduced. The proposed method can effectively reduce the phase current harmonics caused by both back EMF distortion and voltage vector selection, and still reserve the advantages of the conventional ST-DTC, such as fast torque response and simple structure. Its effectiveness is verified by simulations and experiments. [ABSTRACT FROM AUTHOR]

High-speed brushless dc (BLDC) drives usually operate with low carrier–fundamental frequency ratio, which causes abundant sideband harmonic current components. Some sideband harmonics will be induced in low-frequency range, leading to low-frequency current oscillations and low-frequency torque ripples. To minimize these undesired sideband harmonics, a novel pulsewidth modulation commutation pattern, i.e., carrier-synchronized commutation (CSC), is proposed in this article. For comparison, two conventional commutation patterns, including regular-sampled commutation (RSC), and natural-sampled commutation (NSC), are analyzed. To reveal the characteristics of sideband harmonics caused by RSC and NSC patterns, an extended geometric wall model is introduced, which can be used for the Fourier decomposition of complex vectors. Theoretical, simulation, and experimental results demonstrate the conventional RSC and NSC patterns will produce additional sideband harmonic currents and torque ripples, while the proposed CSC pattern can considerably suppress these adverse influences and meanwhile presents high performance and robustness. [ABSTRACT FROM AUTHOR]

A novel asymmetric interior permanent magnet (AIPM) machine is proposed in this paper for electric vehicle application. It has a skewed V-shape permanent magnet (PM) cavity, two PMs with different dimensions and an additional flux barrier outside the V-shape cavity in each pole. This asymmetric rotor topology can inherently utilize the magnetic-field-shifting (MFS) effect to reduce the current angle difference between the maximum PM and reluctance torque components, thereby enhancing the maximum synthetic torque with the same PM usage. The influences of cavity positions in the proposed AIPM and an existing AIPM with extra flux barrier inside the V-shape cavity are investigated and compared using finite element analysis. It is found that the proposed structure with outside flux barrier has higher average torque than the one with inside flux barrier. Both AIPM topologies are designed with the same stator, rotor diameter, and PM usage as the conventional V-shape IPM benchmark for Prius 2010. Electromagnetic, mechanical and steady-state thermal performance of three machines are compared. The results confirm that the proposed AIPM machine can achieve significant torque enhancement due to utilizing MFS effect, compared with the existing AIPM and the IPM benchmark. Finally, a small prototype of the proposed AIPM machine is designed, manufactured and tested to validate the FE analysis. [ABSTRACT FROM AUTHOR]

The induced voltage ripple in DC field windings can cause many problems in hybrid excitation machines (HEMs). It can generate ripple current in field winding, thus causing unsteady magnetic field excitation and hence additional torque ripple and losses. Besides, the torque and power density of hybrid excitation machines may be deteriorated as a result of the influence of the induced voltage ripple on field winding's excitation circuit, particularly under high-speed conditions. Based on a hybrid excitation switched flux machine (HESFM), the influence of stator slot and rotor pole number combination on no-load and on-load field winding induced voltage ripples are studied and compared by the finite element method (FEM). It reveals that the harmonic content and thus the peak-to-peak value of the field winding induced voltage ripple are closely related to the stator slot and rotor pole number combination at both no-load and on-load operating conditions. The FEM calculations are verified by experiments on a prototype HESFM. [ABSTRACT FROM AUTHOR]

Spoke array permanent magnet (PM) flux reversal machines (SAFRPMMs), which are suitable for low speed and high torque applications, are able to enhance torque density due to the flux focusing effect. In this paper, what influence both the number of PM per slot and the PM shape have on their electromagnetic performance are investigated. The results show that both the PM number and the PM shape have significant effects on the performance of SAFRPMMs, and proper selections are critical in designing high performance machines. When the PM number per slot is 2, the SAFRPMM exhibits the best electromagnetic performances, i.e., the highest torque, power, efficiency, and power factor. Meanwhile, by properly designing the PM shape, the torque can be further improved by around 11%. A prototype is made and tested to validate the analyses. [ABSTRACT FROM AUTHOR]

Current harmonics are ubiquitous in dual three phase (DTP) permanent magnet synchronous machine (PMSM) drives. Due to back electromotive force (EMF) distortion, significant current harmonics are generated in the DTP-PMSM system. The influence of back EMF harmonics is investigated in this paper and a novel switching-table-based direct torque control method to compensate the selected current harmonics caused by the back EMF harmonics is proposed. It shows that by employing different optimal action time durations for voltage vectors in the z1z2 subspace and setting the synthetic voltage vectors to non-zero, the stator flux harmonics caused by the back EMF harmonics can be selectively compensated, as verified by experiments. [ABSTRACT FROM AUTHOR]

Automotive starter-generator applications require a high peak torque for cranking and a wide speed flux weakening region for generation. In such applications, the pole-changing winding induction machine offers a wide speed flux weakening region with a low pole number and a high peak torque capability when operated with a higher number of poles. In this article, a 6-phase, electronic pole-changing winding induction machine with improved performance over the existing 3-phase pole-changing is discussed. Compared to the 3-phase 120o phase belt winding, the proposed 6-phase pole-changing winding induction machine shows a 15 % increase in peak torque due to improved winding factor. Finite element analysis is used to predict the torque capability, losses and efficiency of the 6-phase and 3-phase pole-changing winding induction machines. A 1kW induction machine is prototyped and the improved torque capability of the 6-phase pole-changing machines over 3-phase counterparts is experimentally validated under various operating conditions. [ABSTRACT FROM AUTHOR]

In this article, a new type of consequent pole flux reversal permanent magnet (CFRPM) machine, which features more iron poles than PM poles under one stator tooth, is proposed to improve the torque density. The proposed CFRPM machine with 6 slots and 16 poles (6S16P) is compared with a 12S16P FRPM machine and its consequent pole type, as well as a conventional 6S4P surface-mounted PM (SPM) machine. The proposed 6S16P CFRPM shows the highest torque among the four machines, together with the highest torque per PM volume. For a fair comparison with the 12S16P FRPM machine and its consequent pole type, the torque ripple of the proposed 6S16P CFRPM is suppressed by using two-step skewed rotor. After employing 4° two-step skewed rotor, while exhibits comparable torque ripple, the proposed 6S16P CFRPM still has 43% and 22% higher torque compared with the 12S16P FRPM machine and its consequent pole type. [ABSTRACT FROM AUTHOR]

An electronic pole-changing winding induction machine with eight and four poles for a 48-V starter-generator application is studied in this article. Starter-generators require high torque capability for short durations at low speed for cranking, a wide flux weakening region for regeneration, as well as high torque density, so that the machine may be integrated into a drive train with minimum change to the existing system. In this article, it is shown that when pole-changing windings are used, the axial length of the machine can be reduced compared to the baseline induction machine design, resulting in a more compact machine. The effects of shorter stack length and pole-changing windings on the performance of the induction machine are studied. Efficiency, loss, and power factor maps are calculated with analytical and finite-element methods and experimentally validated to compare the performance of the pole-changing winding induction machine with a baseline design under various operating conditions. [ABSTRACT FROM AUTHOR]

In the high-speed brushless dc drives, long commutation freewheeling duration will increase the difficulty of sensorless operation that is based on the back electromotive force (EMF) zero-crossing detection. In extreme cases when the freewheeling angle exceeds 30°, the zero crossing of back EMF will be undetectable, resulting in the failure of sensorless drives. As a result, the sensorless safety operation area (SOA) is limited by the long freewheeling angle issue. In this article, it is found that the pulsewidth modulation (PWM) patterns have a big influence on the freewheeling angle. Hence, in the first place, through analytical methods, the mechanism that how different PWM techniques affect the freewheeling angle is investigated. The PWM pattern resulting in a minimum freewheeling angle is identified. Furthermore, a method to predict the SOA is developed, which provides a theoretical way to verify whether the predesigned torque and speed area can be achieved with the given motor parameters. Finally, the theoretical analysis is verified by the simulation and experimental results. [ABSTRACT FROM AUTHOR]

In this article, a current profiling technique is proposed for the torque density enhancement in switched reluctance machines (SRMs). The novel current profile is initially developed from the harmonic current injection method and is then modified into a unipolar waveform to allow the application of an asymmetric bridge inverter. It is found that, neglecting the magnetic saturation, the optimal current profile for the maximum torque per ampere operation in an SRM is close to a pulse with high-order harmonics. However, an optimized current with relatively low-order harmonics can provide better performance in the practical situation. Based on the analytical and the finite element results, the proposed method is proved to be able to enhance the torque density by 20% at the light load condition and by 15% at the rated condition compared with the conventional SRM excitation. Also, the large torque ripple and core loss in SRMs are suppressed and the efficiency is improved. More importantly, unlike many other current profiling techniques, the proposed current profile has fixed parameters and is easily adaptable to different machine specifications. The effectiveness of the proposed method is verified by both the finite-element analyses and the experiments. [ABSTRACT FROM AUTHOR]

The second harmonic current injection method is recently developed to enhance the torque density of variable flux reluctance machines (VFRMs). This article investigates the feasibility and effectiveness of the second harmonic current injection method in VFRMs with different stator/rotor pole combinations. By using magnetic gearing effect, it is found that the second harmonic injection method can only be applied to the 6j/(6i ± 2)j (i, j = 0, 1, 2…) stator/rotor pole VFRMs for the torque density enhancement. For the other stator/rotor pole combinations, the second harmonic current has no contribution in average torque production but only leads to excessive torque ripple. Further, by using global optimization method and finite element analysis, 6/8 stator/rotor pole combination is proved to be the optimal stator/rotor pole combination for 6-stator-slots VFRMs with the second harmonic current injection method, being able to exceed the maximal torque density of conventional VFRMs by 12% at a fixed copper loss. [ABSTRACT FROM AUTHOR]

In the past, various fundamental model based sensorless control methods have been proposed. However, most of them are developed under a healthy condition. Hence, in this article, fundamental model based sensorless control of permanent magnet synchronous machines (PMSM) under rotor eccentricity (RE) is investigated which is a common issue in many drive systems. It is known that under RE, three-phase back-EMFs, flux-linkages, inductances, and torque will be influenced. Mathematical derivation reveals that these effects will cause undesired harmonics in the position estimation. Since the frequencies of these low-order harmonics are much smaller than the bandwidth of position observer such as phase-locked loop, it is difficult to effectively eliminate them. Hence, the conventional back-EMF method is modified by adding an adaptive notch filter to suppress these undesired harmonics. Furthermore, the RE effects on PMSM characteristics are examined by measurements. The modified position estimator is implemented on a dSPACE platform and is verified by experiment results. [ABSTRACT FROM AUTHOR]

Hybrid excited (HE) machines have the synergies of high torque density and high efficiency of permanent magnet (PM) machines and excellent flux controllability of wound-field machines. The PMs and field coils (FCs) coexist in HE machines to provide excitations simultaneously, and can be coupled either in series or parallel. The topologies of HE machines are very diverse, which bring challenges in the selection and design of HE machines. Based on the partitioned stator (PS) platform, a pair of series and parallel HE machines having similar structures and PM usage are evaluated and compared to identify their merits and demerits. With the help of finite element analysis, the flux regulation, energy conversion capability, parasitic effects and irreversible demagnetization of the two kinds of the HE machines are comprehensively investigated and the guidance to the machine design is provided. A pair of prototypes are fabricated and tested to validate the analyses. [ABSTRACT FROM AUTHOR]

In order to provide the general guidance in constructing the novel modular machines with redundant teeth, the available slot and pole number combinations based on the balanced conditions are summarized in this article. After the brief review of the machine structure, the general slot and pole number combinations are listed: Firstly, the conventional modular machines used to construct the proposed modular machines need to possess integer times of 3 repetitive machine units. Each machine unit should construct as a 3-phase type. Then, a redundant machine unit providing the redundant teeth for modularity is necessary. This redundant machine only has one pole pair to make sure the space waste is minimal. The slot number of this redundant machine is determined by the greatest common divisor of the slot and pole pair numbers of the conventional modular machine. Finally, the combination of the conventional modular machine and the redundant one generates the proposed modular machine. In order to clearly illustrate the influence of slot and pole number combinations on machine performance, four combinations are chosen as examples to be compared. A 42-slot/32-pole machine is prototyped and tested to validate the analyses. [ABSTRACT FROM AUTHOR]

In this article, spoke array permanent magnet (PM) flux reversal machines (SAPM FRM), which feature spoke array PMs distributed along the stator inner surface, are proposed to improve the torque density. Compared with the conventional surface mounted PM flux reversal machine (SPM FRM), the proposed SAPM FRM can produce about 100% larger torque with negligible torque ripple, as well as higher efficiency and higher power factor. Two prototypes have been built and tested to validate the theoretical analyses. [ABSTRACT FROM AUTHOR]

This article investigates the nonlinear behavior of the conventional voltage feedback flux-weakening control, i.e., the voltage magnitude feedback control on the nonsalient permanent magnet synchronous machine, and proposes an adaptive control parameter tuning method for the voltage feedback controller. Due to less voltage margin in the flux-weakening region, the current dynamic performance is degraded. This issue is more serious when the system operates in the overmodulation region and could affect the system's stability. Based on the designed voltage feedback controller, the system performance in the flux-weakening and overmodulation regions is further improved by utilizing the current and voltage reference modifiers. Consequently, the system can operate well in both linear and overmodulation regions with the specified scaling factor, which is beneficial to general-purpose applications. The viability of the proposed method is demonstrated by the experimental results. [ABSTRACT FROM AUTHOR]

This paper proposes a consequent-pole flux reversal machine (CP-FRM) with biased flux modulation theory, which employs homopolar permanent magnets (PMs) placed between the adjacent stator poles. The machine topology is introduced from the perspective of FRM with a shifted magnet position and CP arrangement, and the performance comparison between the proposed CP-FRM and its original surface-mounted PM (SPM) counterpart is presented to highlight the torque improvement of the CP structure. Then, a simplified permeance model is applied to the CP-FRM to identify the principal effective air-gap field harmonics engaging in the torque productions. It shows that the CP-FRM works based on a biased flux modulation effect due to its asymmetric air-gap field distribution caused by the CP configuration, which unveils its underlying torque improvement mechanism over its SPM-FRM counterpart. In order to obtain the highest torque capability, the key design parameters are analytically optimized by analyzing the winding configuration, which aids the establishment of a general design guideline for the CP-FRM. The analytical and FE results are validated by experiments. [ABSTRACT FROM AUTHOR]

This article investigates the duty-ratio-based direct torque control strategies for dual three-phase permanent magnet synchronous machine (PMSM) drives. The classical switching-table-based direct torque control (ST-DTC) for the dual three-phase drives usually suffers from significant harmonic currents and a large torque ripple. To reduce the harmonic currents, 12 combined voltage vectors are generated and employed as active vectors. Then, the duty-ratio-based ST-DTC is introduced to reduce the torque ripple. Considering that the typical duty-ratio-based ST-DTC exhibits the drawbacks of machine parameter dependent and a certain degree of failure rate in the duty ratio regulation, a simple and effective method taking into account the effect of the machine speed is employed to obtain the duty ratio. Afterward, to prevent the issue of the inverter thermal imbalance caused by using only one type of zero vectors, two types of zero vectors are employed in the switching sequences. With the proposed method, not only the harmonic currents have been suppressed, but also the torque ripple can be considerably reduced, while the merits of the classical ST-DTC such as simple structure and excellent dynamic performance are preserved. The experimental results validate the effectiveness of the proposed strategy. [ABSTRACT FROM AUTHOR]

This paper aims to identify the optimal number of flux modulation pole (FMP) in Vernier permanent magnet synchronous machines (VPMSMs) with concentrated tooth-coil windings. First, the influence of number of FMP on machine performance is revealed based on the unified permanent magnet magnetomotive force permeance analytical model. It is found that for a fixed stator slot number, there always exists an optimal number of FMP to maximize the torque, thanks to the enhanced contribution by the fundamental permeance harmonic. Then, the influence of critical dimensional parameters, including the machine diameter, the permanent magnet thickness, and the width of FMP, on the electromagnetic performance of VPMSMs with different numbers of FMP are parametrically analyzed by both analytical and finite element analyses. Results show that the VPMSMs with the optimal number of FMP always have advantages of a higher torque density together with a reduced PM volume, particularly for those with a relatively large diameter. Finally, two VPMSM prototypes with different numbers of FMP are manufactured and tested to validate the analyses. [ABSTRACT FROM AUTHOR]

Fractional slot concentrated winding (FSCW) permanent magnet synchronous machines (PMSMs) have been a research hotspot over the past few decades. Recently, the magnetic gearing effect in FSCW PMSMs is revealed along with its gear ratio, which is a function of slot/pole number combination. At the design stage of FSCW PMSMs, one of the key issues is the selection of the slot/pole number combination. This paper shows that the gear ratio can contribute to a proper slot/pole number selection in any multiphase FSCW PMSMs by acting as a unified index for a quick overall performance comparison. In this paper, first, the magnetic gearing effect in FSCW PMSMs is explained and the gear ratio is further discussed. The advantages of adopting gear ratio as the overall performance index over other indices are revealed. The influence of the gear ratio on the winding factor, torque output, cogging torque, inductance, and rotor losses of three- and six-phase FSCW PMSMs is analyzed and validated by experiments, thus proving the analyses. [ABSTRACT FROM AUTHOR]

For hybrid-excited doubly salient synchronous machine, both the field excitation current and the d-axis current can be utilized to adjust the flux-linkage, which provides more flexible control parameters for flux-weakening operation. In this paper, three flux-weakening control methods, i.e., utilizing field excitation current alone (Method I), utilizing armature current alone (Method II), and optimal method (Method III), are proposed and compared. All three methods can achieve similar torque performance in the constant-torque region. In the flux-weakening region, Method I exhibits low torque and limited operating speed range. The operating speed range can be further extended by Methods II and III. In addition, Method III can provide a higher efficiency in flux-weakening region than Method II since the copper loss of field winding can be decreased in proportion to the reduction of field excitation current. Those flux-weakening control methods are verified by experimental results. [ABSTRACT FROM AUTHOR]

This paper presents a novel modular stator hybrid-excited synchronous machine with stator slot permanent magnets (PMs). By regulating the field current, the magnetic field, and consequently the back electromotive force, as well as the average torque can be controlled. The existence of stator slot PMs alleviates the magnetic saturation and improves the flux regulation ratio. The frozen permeability method is employed to investigate the torque contributions by different magnetic sources. Possible stator and rotor pole combinations are illustrated, and the corresponding electromagnetic performances are evaluated with the finite-element method. It is revealed that 12-stator pole machines with 11- and 13-rotor poles exhibit superior average torque and lower torque ripple due to even-order harmonics elimination. Finally, a prototype with modular stator segments is manufactured to validate the analyses and simulations. [ABSTRACT FROM AUTHOR]

This paper aims to comprehensively analyze the influence of number of permanent magnet (PM) pieces on electromagnetic performance of flux reversal permanent magnet (FRPM) machines. First, the unified analytical model of FRPM machines having different numbers of PM pieces is established, from which the optimal number of PM pieces and the corresponding rotor pole number can be identified. It shows that by employing the optimal number of PM pieces instead of the conventional two on each stator tooth, additional back-EMF component can be generated which is beneficial to boost the machine performance. Then, the influence of critical design parameters including stator slot opening ratio, split ratio, and stator slot number is investigated, providing a guidance to the design of FRPM machines aiming at maximum output torque. In addition, both finite element analyses and experimental tests are conducted to verify the analytical analyses. For 6-slot-stator FRPM machines, experimental results show that more than 40% higher output torque can be achieved in the machine with optimal number of PM pieces when compared to the conventional one. [ABSTRACT FROM AUTHOR]

This paper investigates the torque production and the torque ripple reduction of a six-stator/seven-rotor-pole (6/7) variable flux reluctance machine (VFRM). As a main advantage, the 6/7 VFRM produces higher torque density, but less torque ripple compared with the 6/4 VFRM. The instantaneous torque equation of the 6/7 VFRM is derived by considering the spectra of the winding inductance and current. Based on the derived equation, the average torque is found to be mainly produced by the mutual inductance between the field and armature windings. The even-order harmonics of self-inductance and odd-order harmonics in mutual inductance between the field and armature windings are eliminated due to the opposite polarity connection of the armature coils in each phase. This results in the elimination of the third harmonic torque ripple, while a multiple of the sixth harmonic torque ripple exists. In order to mitigate the sixth harmonic torque ripple, the harmonic current injection method is implemented into the field winding. The field harmonic current is calculated from the analytical torque ripple equation. The performance of the proposed methods is verified by both finite element analysis (FEA) and experiment. [ABSTRACT FROM AUTHOR]

In this paper, the open-circuit dc-winding-induced voltage in a wound field switched flux (WFSFs) machines is analyzed. The phenomenon of open-circuit dc-winding-induced voltage is illustrated and the mechanism is explained. Rotor skewing is proposed to reduce the open-circuit dc-winding-induced voltage, and the optimal skewing angle is analytically derived based on the analytically deduced harmonic orders of the open-circuit dc-winding-induced voltage. Finite-element (FE) analyses show that the open-circuit dc-winding-induced voltages in the analyzed 12-stator-pole partitioned stator WFSF machines having 10-, 11-, 13-, and 14-rotor-pole rotors can be effectively reduced by >94%, while the ac-winding phase-fundamental back-EMFs can be maintained by >95%. Twelve/ten-stator/rotor-pole prototypes with skewed and nonskewed rotors are built and tested to verify the analytical and FE results. [ABSTRACT FROM AUTHOR]

This paper provides a comprehensive analysis of performance difference among various kinds of flux reversal permanent magnet (FRPM) machines having different permanent magnet (PM) arrangements. Four PM arrangement types are, first, identified by the number and relative polarities of PMs on the stator teeth, and their influence on the equivalent pole-pair number of the armature winding and working harmonics of the air-gap field is revealed. Then, the torque variation against the rotor pole number of each PM arrangement is analyzed. The electromagnetic performance of four PM arrangements with a 14-pole rotor is compared in detail. It shows that the FRPM machine, in which four PM pieces are mounted on each stator tooth and two adjacent magnets on different stator teeth are of opposite polarities, offers the highest torque density and the highest efficiency, which make it promising in low-speed high-torque applications. In addition, four prototype machines are manufactured and tested to validate the findings. [ABSTRACT FROM AUTHOR]

DC winding induced voltage pulsation in the wound field synchronous machines (WFSMs) will cause dc winding current ripple, challenge the dc power supply, and deteriorate the control performance, especially at high speed. In this paper, the influence of dc winding configuration including the dc coil number and the parallel branch number on its induced voltage pulsation is investigated for WFSMs. Based on the modeling of both open-circuit and on-load dc winding induced voltages, the preferred dc winding configurations for WFSMs having various stator/rotor pole number combinations with double layer or single layer ac windings are obtained and validated by finite element (FE) analysis on four typical partitioned stator WFSMs (PS-WFSMs). A PS-WFSM prototype is built and tested to validate both analytical and FE analyses. [ABSTRACT FROM AUTHOR]

This paper proposes an axial flux magnetically geared (AFMG) permanent magnet (PM) machine for power split application in hybrid electric vehicles. The proposed AFMG machine has the merits of simple structure and improved torque density by combining a magnetic gear with a PM machine. The machine can realize power split with the help of dual mechanical ports and one electrical port, i.e., the input mechanical power and/or electrical power produced by the machine can be split or integrated. The operation principle and two feasible stator slot/rotor pole combinations are analyzed. Moreover, the influence of the machine parameters on the output torque as well as the performance of both combinations are investigated and compared by using JMAG three-dimensional finite element analysis (FEA). In addition, the method of boosting the machine torque is described and experiment results of the proposed machine prototype are provided and compared with FEA results. [ABSTRACT FROM AUTHOR]

This paper introduces a novel hybrid-excited stator slot opening permanent magnet (PM) machine (HSSPMM). The operation principle of the machine is described and the effects of rotor eccentricity and magnetic saturation due to PMs on electromagnetic performance, with particular emphasis on back electromotive force (EMF), are analyzed by finite element method (FEM). It shows that different from the conventional PM machines, the open-circuit back EMF in this novel HSSPMM should be zero but may become non-zero if significant magnetic saturation exists, and furthermore, the rotor eccentricity has a detrimental effect on the waveforms, amplitudes, and symmetries of three-phase back EMFs, as confirmed by FEM and tests. [ABSTRACT FROM AUTHOR]

This paper comprehensively studies the electromagnetic performance of flux-reversal permanent-magnet (FRPM) machines with different consequent-pole PM (CPM) topologies. Four CPM topologies are first introduced and classified by different numbers of PM pieces and PM locations on stator teeth. Then, the distribution and working harmonics of air-gap flux density of each CPM topology are analyzed and compared, from which the CPM topology with the highest torque density is identified. The influence of critical design parameters on machine performance is also parametrically investigated. By comparing the torque performance of CPM topologies with their surface-mounted PM counterparts, the advantages of CPM topologies, i.e., torque improvement and magnet volume reduction, are clearly revealed. Four FRPM prototypes are manufactured and tested to verify the analyses. [ABSTRACT FROM AUTHOR]

Permanent magnet (PM) machine has received much attention recently. However, unbalanced magnetic force (UMF) may occur in PM machines with some slot/pole number combinations even when there is no rotor eccentricity, which can cause high vibration and noise. In order to reduce the rated on-load UMF, three 3-slot/2-pole PM machines with different auxiliary slots are investigated and compared in this paper. In the first two machines, namely, machines 1 and 2, the auxiliary slots are inserted in the middle of the stator teeth, while their sizes are optimized under different working conditions, i.e., no-load and rated on-load conditions. In contrast, both position and size of auxiliary slots are optimized under the rated on-load condition in the third machine viz., machine 3. Compared with the conventional prototype machine, the maximum rated on-load UMFs are reduced by 6.3%, 50.7%, and 96.6%, and the rated output torques are decreased by 0.7%, 11.5%, and 4% in these three machines, respectively. In addition, the other electromagnetic performances, such as flux linkage, back electromagnetic force, cogging torque, rated output torque, and torque ripple, are compared. The influence of working conditions is investigated, and the experiments are also carried out to validate the numerically predicted results. [ABSTRACT FROM AUTHOR]

In this paper, the torque production of fractional-slot concentrated-winding (FSCW) permanent-magnet synchronous machines (PMSMs) is analyzed from the perspective of the air-gap field harmonics modulation accounting for slotting effect. It is found that the average torque of FSCW PMSM is produced by both the principle of conventional PMSM and the magnetic gearing effect. A finite-element analysis (FEA) based equivalent current sheet model and harmonic restoration method is first used in FSCW PM machines with different slot–pole number combinations to quantify the respective contribution of the conventional PMSM and the magnetic gearing effect to the average torque. The influence of slot opening on the magnetic gearing effect, cogging torque, and torque ripple is analyzed. The results show that the magnetic gearing effect makes a nonignorable contribution to the average torque when a large slot opening stator is used. The expression of the gear ratio in FSCW PMSMs is derived. The influence of gear ratio on the contribution of the magnetic gearing effect to the total torque is investigated by FEA. The FEA-predicted torques are validated by experiments on the prototypes. [ABSTRACT FROM PUBLISHER]

This paper proposes two novel partitioned stator (PS) memory machines based on flux-reversal and switched-flux topologies, respectively. The proposed machines geometrically feature two separate stators with armature winding and hybrid PM excitations, i.e., NdFeB and low coercive force PMs. The proposed PS machines can offer increased available inner stator space for hybrid PM, which is beneficial to the torque improvement. The machine topologies are introduced first in terms of possible PM types with parallel magnetic circuits. The design considerations for hybrid PM are analytically analyzed. Then, the electromagnetic characteristics of the two proposed machines are comprehensively compared by using finite element (FE) method. The commercially available Toyota Prius 2010 machine is referenced as a benchmark for comparison with the optimal PS machine having identical overall dimension in potential context of traction applications. Finally, The FE analyses are validated by experiments on a small-scaled demonstration machine. [ABSTRACT FROM PUBLISHER]

A series hybrid variable flux memory (VFM) machine employing two kinds of permanent magnets (PMs) on alternate rotor poles is investigated. This VFM machine features controllable PM flux and thus good flux-weakening capability, as well as improved torque density. However, it is found that the unipolar end leakage flux occurs if the two kinds of PMs are not balanced. According to the analyses of series connection between two PMs based on the fundamental magnetic circuit, the mechanism of the unbalanced rotor poles and the unipolar end leakage flux is revealed. Further, the rule of obtaining balanced poles is identified and the effects of operating conditions are presented. A series hybrid VFM machine prototype is fabricated and tested. [ABSTRACT FROM AUTHOR]

This paper proposes a double superposition method to quickly and accurately predict the cogging torque and unbalanced magnetic force (UMF) of permanent magnet machines with axial-varying rotor eccentricities. The original axial-varying eccentric machine is cut into several uniform slices along the axial direction and each slice is considered to be axially uniform, i.e., axial even. For each axial-even eccentric machine slice, the circumferential superposition method can be used to predict the cogging torque and UMF of this slice. Finally, the cogging torque and UMF of the original axial-varying eccentric machine can be obtained by using an axial superposition technique which combines the cogging torque and UMF of each slice with different eccentricity magnitudes together. The 3-D finite-element analysis is adopted to validate the efficacy of the proposed method and the merit of high accuracy and computational efficiency is also identified by comparing the results predicted from these two methods. [ABSTRACT FROM AUTHOR]

This paper compares the electromagnetic performance of 10-MW superconducting (SC) generators with three different topologies, i.e., iron-cored stator and rotor topology (ISIRT), iron-cored stator and air-cored rotor topology (ISART), and air-cored stator and rotor topology (ASART). The objective is to provide a powerful insight into the advantages and disadvantages of different topologies, and to establish some design guidelines for selecting an appropriate direct-drive SC generator for offshore wind turbine applications. First, the structures of the three SC generator topologies are introduced. Then, the influence of the SC coil cross-sectional area on torque capability is compared. After that three SC generators with different topologies are optimized, respectively, for further comparison, including the active material cost, weight, harmonics in the electromotive force, torque ripple, field harmonics in the SC coil, and forces on the rotor and stator components, etc. It is found that, with the same SC quantity, the torque capability of the ISIRT is much better than that of the other two topologies. However, the advantage becomes less significant when a larger area of the SC coil is employed. The air-gap flux density waveform of the ASART is much smoother than those of the ISIRT and ISART. The torque ripples of the ISIRT and the ISART are much higher than that of the ASART. The field harmonics (both amplitude and frequency) in the SC coil of the ASART are the lowest. For the ISIRT, most of the force on the rotor is acting on the rotor iron, and thus, the SC coil is more likely to be safe from a mechanical performance point of view and the design of the corresponding supporting structure is simple. However, for the air-cored rotor topologies, nearly all the force is acting on the SC coil. For the air-cored stator, the force mainly acts on the armature winding, whereas for the iron-cored stator, it is mainly on the stator teeth. Due to the excellent mechanical performance of iron, the iron-cored stator is therefore more robust. [ABSTRACT FROM PUBLISHER]