Search

The existing power decoupling control method of modular multilevel converter (MMC) was developed from that of conventional two-level voltage source converters. Therefore, it cannot fully realize power decoupling due to neglecting the coupling effects from submodule capacitor voltage, dc current, circulating current as well as control strategies of circulating current, which inevitably results in inaccurate regulation of active and reactive power, deteriorated system dynamic performance, possible overload operation and eventually threatens the safety and stability of MMC. This paper analyzes the intercoupling among all electrical quantities and corresponding control strategies in MMC. An accurate control model of active and reactive power/current with four coupling paths and influence factors in the rotating frame is also established. A full power decoupling control method has been proposed based on the developed model. The proposed control method can realize accurate and completely decoupled active and reactive power regulation, avoid overload operation, and significantly improve the dynamic performance of MMC. Moreover, it facilitates the parameters selection of MMC controller with no extra cost, which is of great significance for practical projects. The effectiveness and accuracy of the proposed analysis and control methods were verified by both simulation and experimental results. [ABSTRACT FROM AUTHOR]

The dc offset and scaling errors in the voltage and current measurements cause the injection of undesired dc and unbalanced currents into the three-phase input currents and subsequently lead to voltage ripple at the dc output voltage of the ac/dc converter. This paper proposes a compensation scheme for current measurement error where the dc offset and scaling errors in the current measurement are estimated from the voltage ripple characteristics of the dc output voltage ripple combining with simple band-pass and low-pass filters. Meanwhile, the dc offset and scaling errors in the voltage measurement can be rejected by using an advanced current controller developed with a proportional resonant plus a repetitive controller designed in the synchronous (d–q) reference frame. The proposed control algorithm is able to effectively reject the impact of both voltage and current measurement error so that the three-phase input currents are regulated to be balanced and sinusoidal with ultralow dc current component. Meanwhile, the dc output voltage is also well regulated to be pure dc with a negligibly small voltage ripple. The proposed compensation method is developed without the need of extra hardware circuit, sensor, or precise information of system parameters so that it can be considered as more cost effective and robust solution. The effectiveness of the proposed solution is verified by experimental results. [ABSTRACT FROM AUTHOR]

Due to voltage mismatch between phase legs and the dc bus in modular multilevel converters (MMCs), the differential current in MMCs is inherently subjected to circulating even-order harmonics. Repetitive control based active harmonic suppression methods can be adopted to eliminate such harmonics. Nevertheless, conventional repetitive controllers have a relatively slow dynamic response, because all the sampled errors in the past one cycle have to be stored, which causes a response delay for one fundamental period. This paper proposes an improved repetitive control scheme that exclusively copes with even-order harmonics based on the circulating current characteristics of MMC systems. The design details of the even harmonic repetitive control scheme according to the harmonics characteristics are provided. The proposed even-harmonic repetitive control scheme requires halved data memory to store error samplings and the delay introduced by the repetitive controller is also reduced. According to the frequency domain analysis, the even-harmonic repetitive control features faster convergence rate, greater low-frequency gains, higher crossover frequency, and higher tolerance against system frequency deviation, while possessing the same even-order harmonics suppression capability and stability as conventional ones. Simulation and experimental results are presented to show the steady-state harmonics suppression capability, dynamic response, and disturbance tolerance of the proposed even-harmonic repetitive control scheme. [ABSTRACT FROM AUTHOR]

This paper focuses on the influence of repetitive square wave voltage rise time on partial discharge pulse characteristics in the ultra-high frequency range. Paerial Discharge (PD) tests on single-point contact crossed pairs were carried out using repetitive square wave voltages with a wide range of rise times, from 200 ns to 400 μs, including also 50 Hz sinusoidal voltage waveforms. Experimental results show that rise time has a significant influence on magnitude and frequency spectrum of PD pulses. Voltages of shorter rise times generate larger PD pulses with a predominance of high frequency components in the energy spectrum. Interpretations are presented for this phenomenon. [ABSTRACT FROM AUTHOR]

This paper presents a uniform control strategy for the bidirectional ac/dc interlinking converter (BIC) in hierarchical controlled hybrid microgrid. The uniform control strategy unifies different control structures for multifunctional BIC in terms of power management, ac and dc voltage support. With the unified control structure, various triggering mechanisms for BIC mode-switch are not compulsory in response to the relevant scenario changes in the power network. Therefore, the negative consequences, such as unsmooth transition and system collapse due to the inaccurate or slower mode switch, can be avoided. Moreover, the uniform control strategy is also applicable for the hierarchical controlled hybrid microgrid, whose control architecture is typically comprised of the centralized and decentralized levels. This enables the communication fault ride-through capability and the impact from the communication failures can thus be mitigated. To sum up the above two features, the proposed control strategy is able to provide a smooth operation for the BIC without control mode switch in the event of unintentional scenario changes in power or communication network. To verify the validity of the proposed uniform control strategy, the controller hardware-in-the-loop experimental results have been provided in this paper. [ABSTRACT FROM PUBLISHER]

Conventional centralized control strategies may reduce the flexibility and expandability of a modular multilevel converter (MMC) system. To tackle this issue, this paper proposes a distributed control architecture that is capable of assigning certain control tasks to distributed local controllers and improves the modularity of an MMC system. A central controller dealing with the output current regulation based on sensed arm currents is adopted. The control of MMC internal dynamics and the pulsewidth modulation (PWM) generation are distributed into local controllers. Unlike the conventional MMC control that needs all submodule capacitor voltages for capacitor voltage averaging, the proposed capacitor voltage control only relies on local submodule voltage measurement. Consequently, communication-intensive capacitor voltage transmission in each control cycle is not required and the communication burden of the control system can be significantly reduced. The control loops and possible control conflicts among submodules are presented and considered for system stability analysis. The effectiveness of the proposed distributed control architecture and capacitor voltage control for an MMC are confirmed by the start-up, steady state, and transient experimental results. [ABSTRACT FROM PUBLISHER]

The increasing demand for high power density requires the power converter to operate in high switching frequency. Silicon carbide (SiC) power module is regarded as one of the most promising candidates for high-frequency applications due to the superior switching speed and low switching loss. With the increase of switching frequency, the switching loss will be the limiting factor of efficiency. Hence, it should be minimized during each switching transition. The optimization of switching loss is normally achieved by the repetitive double pulse test experiments. It is time-consuming to find an optimum gate resistance to achieve the tradeoff between switching loss and electromagnetic interface. In this paper, an accurate subcircuit model for SiC power module is proposed to assist optimization of switching loss in converter design. By considering the device physics and structure, an accurate Miller capacitance model is obtained. Moreover, a parameter extraction procedure is presented, which is based on the datasheet. Good agreements are achieved between the PSpice simulation and experiment. [ABSTRACT FROM AUTHOR]

This paper proposes a multiple-input versatile matrix converter (VMC) for integrating hybrid ac/dc energy resources and storages to the power grid. The VMC is developed from the traditional indirect matrix converter but operates in the reverse-boost mode rather than in the forward-buck mode. The reverse-boost mode is more relevant here since most renewable sources and energy storages have lower voltages than the grid. The eventual VMC developed uses an alternative nine-switch converter, rather than usual six-switch voltage-source converter, for providing six input terminals in total. One three-phase ac source and three dc sources, or other source combinations, can therefore be connected to the VMC. Powers from these sources are channeled to the three-phase utility grid through the VMC's current-source inverter. Their proper dispatches are guaranteed by the proposed control and modulation schemes, which also help maintain near-sinusoidal input and output current waveforms. Mathematical proofs, simulation, and experimental results have shown that the VMC can indeed operate as intended. [ABSTRACT FROM PUBLISHER]

In this article, a novel bidirectional dc–dc converter (BDC) consisting of an active switched-inductor (A-SL) cell, a zero current ripple cell and an auxiliary capacitor cell is proposed for the battery energy storage system. The proposed BDC integrates with the advantages of high voltage conversion ratio, low power switch voltage stresses, zero ripple current on the low voltage side (LVS), and constant potential difference between the grounds of LVS and high voltage side. Thanks to the use of synchronous rectification technology, the efficiency of the proposed BDC is increased. The operating principles, the characteristics analysis and the parameter design of the proposed BDC are given. In addition, to show the merits of the proposed BDC, a comparison study involves the proposed converter and other BDCs is demonstrated. Finally, some experimental results obtained using a 1000 W prototype are presented to valid the effectiveness of the proposed BDC. 96.43% and 96.67% maximum conversion efficiencies can be achieved in the step-up and step-down modes, respectively. [ABSTRACT FROM AUTHOR]