Search

In this article, a novel bidirectional dc–dc converter (BDC) consisting of an active switched-inductor (A-SL) cell, a zero current ripple cell and an auxiliary capacitor cell is proposed for the battery energy storage system. The proposed BDC integrates with the advantages of high voltage conversion ratio, low power switch voltage stresses, zero ripple current on the low voltage side (LVS), and constant potential difference between the grounds of LVS and high voltage side. Thanks to the use of synchronous rectification technology, the efficiency of the proposed BDC is increased. The operating principles, the characteristics analysis and the parameter design of the proposed BDC are given. In addition, to show the merits of the proposed BDC, a comparison study involves the proposed converter and other BDCs is demonstrated. Finally, some experimental results obtained using a 1000 W prototype are presented to valid the effectiveness of the proposed BDC. 96.43% and 96.67% maximum conversion efficiencies can be achieved in the step-up and step-down modes, respectively. [ABSTRACT FROM AUTHOR]

A correlation-based digital background calibration technique to correct the capacitor mismatch error in successive approximation register (SAR) analogue-to-digital converters (ADCs) is proposed. To facilitate the calibration technique, an energy-efficient detect-and-skip (DAS) algorithm is exploited to perform the pseudorandom noise (PN) injection without adding extra hardware overhead. By randomly injecting the error weights and correlating the ADC output with the PN sequence in the digital backend, the real bit weights are identified. In addition, only the error weights are injected into the residue. Therefore, the residue increment caused by the injection is negligible, and the redundancy overhead is minimized. The proposed calibration technique is verified in a 12-bit SAR ADC. Behavioral simulations show that, with calibration, the signal-to-noise and distortion ratio (SNDR) and the spurious-free dynamic range (SFDR) are increased from 55.6 to 71.2 dB and 64.2 to 90.3 dB, respectively. [ABSTRACT FROM AUTHOR]

In this article, a fixed and smooth-switch-sequence modulation strategy is proposed to equalize the dc-link voltages among the cascaded rectifier. The structure of a single-phase three-level neutral-point-clamped cascaded rectifier is studied. Three core steps of this strategy are analyzed respectively, including carrier wave disposition calculation, fixed pulse generator, and voltage rank function. In addition, a criterion of the degree of the load unbalance is established in order to measure the voltage balancing boundary of the presented approach. The superiorities of the proposed control strategy embody the smooth switch sequence, the strong voltage balance capability, as well as the fixed switch sequence. Owe to these advantages, the cascaded rectifier could effectively reduce the switching frequency, achieve the goals of voltage balancing, and reduce the calculation burden of the controller when the number of cascaded modules is large. The effectiveness of the proposed strategy is verified by simulation and experiment results. [ABSTRACT FROM AUTHOR]

Modularity and high reliability from redundancy are the two attractive advantages of modular multilevel converters (MMCs). This paper elaborates a switch open-circuit fault diagnosis and a fault-tolerant operation scheme for MMCs with distributed control. The proposed fault diagnosis and fault-tolerant control method can significantly improve the reliability of the MMC while maintaining the modularity of its software implementation. By distributing fault diagnosis into submodules, its local controller is capable of identifying the switching devices in open-circuit fault without extra hardware circuitry. Based on the real-time measurements of submodule terminal voltage and arm current, single, or multiple faulty switches can be identified within 3.5 ms without triggering faulty alarms. Furthermore, a new fault-tolerant operation is proposed to maintain the output current, internal dynamics, and switching harmonics unchanged after the faulty submodule is bypassed. This is achieved by resetting the period and phase registers in the local controller according to the information of bypassed submodules. The control loops of the MMC are not influenced by the proposed fault diagnosis and fault-tolerant operation, making the operation transition seamless and reliable. Experimental results show that fault identification and system reconfiguration can be completed within 5 ms, and the MMC can seamlessly and smooth ride through the switch open-circuit faults without severe malfunction and catastrophic damages. [ABSTRACT FROM AUTHOR]

A novel high-efficiency resonant light emitting diode (LED) backlight driver with passive current balancing and dimming is proposed and analyzed in this paper. The proposed LED driver achieves uniform brightness of each LED string by the charge balance of the resonant capacitor, which benefits from high efficiency. By controlling the output current of one LED string, the output currents of other LED strings can be controlled via current balancing of resonant capacitors, which makes its control simple. The proposed LED driver uses only one active switch, which decreases circuit volume and simplifies the control. Furthermore, a wide load range can be achieved by controlling the turn-on duty ratio of the single power switch of the LED driver with a fixed frequency. Finally, a prototype of a high-dimming-ratio small-size three-string LED driver is provided to verify the studied results. [ABSTRACT FROM PUBLISHER]

This paper proposes a novel dual-input matrix converter (DIMC) to integrate two three-phase ac type energy resources to a power grid. The proposed matrix converter is developed based on the traditional indirect matrix converter under reverse power flow operation mode, but with its six-switch voltage source converter replaced by a nine-switch configuration. With the additional three switches, the proposed DIMC can provide six input terminals, which make it possible to integrate two independent ac sources into a single grid-tied power electronics interface. The proposed converter has input-to-output voltage boost capability since power flows from the converter's voltage source side to its current source side. Commanded currents can be extracted from the two input sources to the grid. The proposed control and modulation schemes guarantee sinusoidal input and output waveforms as well as unity input power factors. The simulation and experimental results using a laboratory prototype are provided to validate the effectiveness of the proposed control and modulation schemes for the proposed converter. [ABSTRACT FROM PUBLISHER]