Search

The penetration level of photovoltaic (PV) keeps increasing in modern distribution networks, which leads to various severe voltage limits violation problems. This article aims to aggregate and utilize the PV inverters for voltage regulation by a fully distributed two-level Volt/VAr control (VVC) scheme. In the lower-level VVC (real-time scale), the rooftop PV inverters are aggregated via consensus algorithms and then governed by droop controllers in medium-voltage networks. The droop controller adjusts the reactive power output of each PV aggregator in real-time from its dispatched value depending on the bus voltage variations. In the upper-level VVC (15-min timescale), the reactive power of PV aggregators is dispatched for power loss minimization, where control signals are set as base values for PV aggregators. This problem is formulated as second-order cone programming and solved by the alternating direction method of multipliers. The simulation results demonstrate the effectiveness of the proposed method in both short-term and long-term scenarios with different system scales. [ABSTRACT FROM AUTHOR]

In this article, a fixed and smooth-switch-sequence modulation strategy is proposed to equalize the dc-link voltages among the cascaded rectifier. The structure of a single-phase three-level neutral-point-clamped cascaded rectifier is studied. Three core steps of this strategy are analyzed respectively, including carrier wave disposition calculation, fixed pulse generator, and voltage rank function. In addition, a criterion of the degree of the load unbalance is established in order to measure the voltage balancing boundary of the presented approach. The superiorities of the proposed control strategy embody the smooth switch sequence, the strong voltage balance capability, as well as the fixed switch sequence. Owe to these advantages, the cascaded rectifier could effectively reduce the switching frequency, achieve the goals of voltage balancing, and reduce the calculation burden of the controller when the number of cascaded modules is large. The effectiveness of the proposed strategy is verified by simulation and experiment results. [ABSTRACT FROM AUTHOR]

Power loss and voltage regulation are two fundamental and challenging issues in DC distributed generation system. In this paper, a multi-objective optimization problem is established to achieve trade-offs between reducing power loss and decreasing voltage deterioration by adjusting the weighting coefficients. This problem is proven to be a convex optimization under constant impedance load and constant current load. A distributed algorithm based on random coordinate descent method is developed to solve this problem without acquiring the information of line impedance. Thus, the optimal operating point of the system can be found automatically in real-time, and the deviation of optimal solution caused by the fluctuation of network parameters is avoided. In addition, the complexity of this algorithm is low and its computational requirement is reduced in practice. Finally, case studies are implemented to verify the effectiveness of the proposed algorithm under the scenarios of line parameter fluctuation, load variation, communication line failure, and plug-play capabilities. [ABSTRACT FROM AUTHOR]

Direct modulation principle is widely used in modular multilevel converters (MMCs) for its simplicity and natural stability. However, it results in strong active and reactive power coupling. This paper carefully analyzes and identifies four power coupling paths and two power influence factors with the direct modulation principle. Full power decoupling of the MMC can be realized by cutting off the derived coupling paths and compensating the influence factors. However, this will further deteriorate the already poor damping of the MMC and significantly increase dc-bus current fluctuations. To solve this problem, the sources resulting in poor damping are identified and then a new closed-loop dc-bus current controller is incorporated into the control system. Finally, the proposed power decoupling strategy with the newly designed current controller realizes completely decoupled power regulation, avoids overload operation, and obviously improves the dynamic performance of the MMC. Furthermore, it increases the stability of the MMC system under all possible operation conditions. The proposed control strategy is confirmed by experimental results. [ABSTRACT FROM AUTHOR]

This paper presents a uniform control strategy for the bidirectional ac/dc interlinking converter (BIC) in hierarchical controlled hybrid microgrid. The uniform control strategy unifies different control structures for multifunctional BIC in terms of power management, ac and dc voltage support. With the unified control structure, various triggering mechanisms for BIC mode-switch are not compulsory in response to the relevant scenario changes in the power network. Therefore, the negative consequences, such as unsmooth transition and system collapse due to the inaccurate or slower mode switch, can be avoided. Moreover, the uniform control strategy is also applicable for the hierarchical controlled hybrid microgrid, whose control architecture is typically comprised of the centralized and decentralized levels. This enables the communication fault ride-through capability and the impact from the communication failures can thus be mitigated. To sum up the above two features, the proposed control strategy is able to provide a smooth operation for the BIC without control mode switch in the event of unintentional scenario changes in power or communication network. To verify the validity of the proposed uniform control strategy, the controller hardware-in-the-loop experimental results have been provided in this paper. [ABSTRACT FROM PUBLISHER]

This study proposes an advanced current control strategy for three-phase grid-connected inverters to reject the impact of the dc offsets and scaling errors in the grid voltage measurement on the grid current performance. The proposed current controller designed in the synchronous (d-q) reference frame is developed with a proportional integral (PI) plus three vector PI controllers. The PI controller regulates the fundamental current to follow its reference, meanwhile, three vector PI controllers tuned at the fundamental grid frequency ( \omega _s), 2\omega _s, 6\omega _s are employed to eliminate the dc, unbalance, harmonic components in the grid current. As a result, the three-phase grid currents are controlled to be balanced, sinusoidal, and extremely low dc component despite the presence of the dc offset and scaling errors in the grid voltage measurement and distorted grid voltage conditions. The main advantage of the proposed control scheme is that it is developed without the need of additional hardware circuit, dc extraction, and harmonic detection scheme so that it can be integrated into the existing grid-connected inverter system without extra cost. The effectiveness of the suggested solution is verified by experimental results under various grid voltage conditions and the grid voltage measurement errors. [ABSTRACT FROM PUBLISHER]

Transient electromagnetic scattering by composite structures is formulated by time-domain combined field integral equations (TDCFIEs). Traditionally, the TDCFIEs are solved by combining the method of moments (MoMs) in space domain and march-on-intime (MoT) scheme in time domain. The space-domain MoM requires two basic functions to represent the electric and magnetic current densities on material interfaces, respectively, and the conventional choice of \hat n\times \mathrm RWG basis function for representing the magnetic current density may not be good in the TDCFIEs. In addition, the MoT scheme has a well-known late-time instability problem, which will aggravate in the surface integral equations with penetrable media. In this communication, the TDCFIEs for composite structures are solved by a different approach in which the Nyström method is used to discretize the space domain, while the Galerkin method with Laguerre basis and testing functions is employed to discretize the time domain. The proposed approach can fully overcome the drawbacks of the traditional approach as demonstrated by numerical examples. [ABSTRACT FROM AUTHOR]

This paper reviews results of partial discharge measurements and accelerated life tests performed on models of random and form wound insulation systems subjected to impulse voltage waveforms. The goal is to highlight how the features of the supply voltage affect the partial discharge activity and how this, eventually, reflects on the endurance of the insulation system. The most salient results are that, for both types of insulation systems, short rise times trigger PD of large magnitude, which are able to erode the insulation system faster than the partial discharges incepted using waveforms with longer rise times. In particular, failure times estimated by tests under sinusoidal voltages can be overly optimistic in assessing the long-term behavior of the insulation system subjected to impulse voltage waveforms. Frequency also is very important, as it controls the interplay between physical and chemical degradation rates. As a result, above partial discharge inception voltage the frequency acceleration rule does not hold, and can lead therefore to excessively optimistic results. [ABSTRACT FROM AUTHOR]

Multiple-voltage-region control, in which the bus-voltage range is divided into several regions, is usually implemented for dc microgrid operation in distributed manner. Voltage/power droop relationships are imposed for active power sharing among slack terminals. Conventionally, threshold voltages for voltage region partition are determined with fixed percentage of variation around the nominal value, which may result in unevenness of droop coefficients in different regions. If system droop coefficient is too high, significant bus-voltage step change due to load variation will occur. On the other hand, significant power sharing error among slack terminals will be induced if the droop coefficient is too low. In this paper, a compromised solution with power-capacity-based bus-voltage region partition is proposed to equalize the droop coefficients in different regions. However, the droop coefficients are determined based on the rated power capacity of system units. Bus-voltage discontinuity appears when the power capacity reduces in actual implementation. To eliminate the voltage discontinuity, online droop coefficient tuning according to the real-time power capacity is implemented. Algorithms for local power capacity estimation of solar photovoltaic (PV) and battery energy storage have been proposed. A lab-scale dc microgrid has been developed for verification of the proposed methods. [ABSTRACT FROM AUTHOR]

To address the reliability of rotating machine insulation, the International Electrotechnical Commission implemented new standards and technical specifications that are relevant to low-voltage and medium-voltage inverter-fed motors. Insulation evaluation under such power supply relies upon partial discharge (PD) measurements and accelerated life tests, which should be conducted (at least for the turn-to-turn insulation) under impulsive voltage waveform. The effect of impulsive voltage parameters on PD inception voltage and, in particular, endurance tests must be investigated to design test procedures that can indicate insulation quality and its behavior in service. This paper examines the effect of repetitive impulsive voltage waveform parameters on PD and the endurance (life) of organic insulation for rotating machine wires based on experiments performed on single-contact crossed pairs. Results show that the features of repetitive voltage impulse affect PD time and frequency characteristics, PD phase distribution, and endurance. Consequently, evaluation of insulation subjected to power electronics waveforms should take into account the appropriate choice of impulsive voltage parameter to fit to the type of PD phenomenology occurring in service conditions. [ABSTRACT FROM PUBLISHER]

The dependence of endurance test results on repetitive square wave voltage waveform parameters is investigated in this paper focusing on crossed pair specimens made of polyamide-imide enameled wires. Endurance tests carried out on crossed pairs above partial discharge inception voltage using both sinusoidal and square wave voltages show that lifetimes can be influenced significantly by voltage waveform parameters (rise time and frequency). Partial discharge statistics, recorded from test beginning to breakdown, are used to explain the remarkable differences associated with voltage waveform parameters. According to this study, the influence of voltage waveform parameters should be carefully considered in order to obtain effective evaluation of inverter-fed motor insulation systems. [ABSTRACT FROM AUTHOR]

Indirect matrix converter (IMC) is an alternative for ac/ac energy conversion, usually operated with a voltage stepped-down gain of only 0.866. For applications like distribution generation where voltage-boost functionality is required, the traditional style of operating the IMC is therefore not appropriate. Like most power converters, the operation of the IMC can surely be reversed to produce a boosted gain, but so far its relevant control principles have not been discussed. These challenges are now addressed in this paper with distributed generation suggested as a potential application. Simulation and experimental results for validating various performance aspects of the proposed control schemes can be found in a later section of this paper. [ABSTRACT FROM AUTHOR]

This paper focuses on the influence of repetitive square wave voltage rise time on partial discharge pulse characteristics in the ultra-high frequency range. Paerial Discharge (PD) tests on single-point contact crossed pairs were carried out using repetitive square wave voltages with a wide range of rise times, from 200 ns to 400 μs, including also 50 Hz sinusoidal voltage waveforms. Experimental results show that rise time has a significant influence on magnitude and frequency spectrum of PD pulses. Voltages of shorter rise times generate larger PD pulses with a predominance of high frequency components in the energy spectrum. Interpretations are presented for this phenomenon. [ABSTRACT FROM AUTHOR]

A novel one transistor and one diode (1T-1D) dynamic random access memory cell for embedded applications is proposed. This memory cell consists of a floating-gate (FG) MOSFET and a gated diode. The anode of the diode is connected to the FG, so that the threshold voltage of the FG MOSFET can be modulated by the current through the diode. In this paper, basic device operations, speed, retention, and disturb performance are investigated using Silvaco technology computer-aided design simulation tools. The process compatibility is also investigated by integrating the memory array and specific sense amplifier. [ABSTRACT FROM PUBLISHER]

For measuring currents flowing in three-phase rectangular-shaped busbars, in this paper, a planar coil with air core is used as a current sensing unit. The vector potential of the busbar and the electromotive forces of the planar coil for single- and three-phase currents are calculated with a numerical integration arithmetic. The relative error caused by adjacent busbars was simulated when the transducers were used for the three-phase current measurement. The simulation results show that the relative error induced by the adjacent busbars is less than 2%. Planar-coil-based current transducers enclosed with silicon rubber insulator are developed. The successful field trial of the transducers for more than four years shows that the transducers can meet the field requirement. [ABSTRACT FROM PUBLISHER]

In this paper, a modified one-cycle-control (OCC) scheme is proposed for regulating three-phase pulsewidth-modulated (PWM) rectifiers operating under unbalanced and distorted supply conditions. Mathematical analysis is first presented to show the dominant harmonic-voltage components appearing across the dc link of the PWM rectifier when it is controlled by an existing OCC scheme. Such dc-link harmonics when produced may aggravate harmonic currents flowing into the input terminals of the three-phase rectifier. To address these interrelated unbalance and harmonic concerns, the concept of reconstructing the appropriate reference signals in the OCC control core is introduced, before modifications are recommended for altering the key control equation. The improved OCC controller eventually developed is proven to exhibit minimal input-current distortion and a smoother dc-link voltage without using large capacitance. Other advantages exhibited by the traditional OCC scheme, such as no phase-locked loop, no frame transformation, and constant switching frequency, are also retained by the improved controller, whose theoretical findings are fully verified by experimental results obtained from a 1.2-kW three-phase PWM rectifier built in the laboratory. [ABSTRACT FROM PUBLISHER]

The Kerr effect in liquid of propylene carbonate near an insulator surface excited by pulsed high voltage was electro-optically measured with the data produced in the form of finite fringe interferograms. The fringe in the cathode region near the insulator surface was observed to shift inward, which implies a decrease of the cathode field near the insulator surface and somewhere near the cathode on the insulator surface being negatively charged. [ABSTRACT FROM PUBLISHER]