Search

This study used the Electric Spark Discharge Method (ESDM) to prepare nano-Ti colloid. The results showed that the process efficiency increased according to the current and selecting different discharge periods (TON-TOFF). The preparation process is pollution-free and very contributive to using TiO2 for photocatalytic reaction to degrade organic compounds. This study used 99.9% pure Ti metal to examine the effects of different discharge parameter settings on the photocatalysis of methylene blue. The experimental results showed that the discharge period (TON-TOFF) has an effect on the characteristics of the prepared nano-Ti colloid but affects its concentration. The nano-Ti colloid, as prepared under different parameters, has poor photocatalytic reaction with methylene blue at the concentration of 50 mg/L. The nano-Ti colloid does not have favorable effect on degrading methylene blue above 50 mg/L. For degrading methylene blue at a low concentration of 10 mg/L, the 100-100 nano-Ti parameter is preferable. For degrading methylene blue at a high concentration of 30 mg/L, nano-Ti colloid with TON exceeding 100 and TOFF fixed at 100 is better. As the nano-Ti colloid prepared by ESDM was free of chemical agents, when TiO2 was used in photocatalytic reaction to degrade organic compounds, there was no secondary pollution to the environment.

The colloidal silver solution was successfully prepared in dielectric fluid by using electrical spark discharge (ESD) without any surfactants. It does not require the toxic chemical agents in the process, which may affect the effectiveness of nanosilver colloid as an antibacterial agent. Nanocolloidal silver produced by ESD is characterized as low cost, zero environmental pollution, continuous, and rapid mass production process. In order to test the effect of antibioactivity, nanosilver dough was tested; the silver nanofluid was prepared by ESD machine, made into dough at different concentrations, and fermented for three hours in order to observe changes in the diameter of the dough. The results showed that the effect of effectiveness of nanosilver at the concentration of 100 ppm was weak, whereas the effect of 60 ppm silver ion (100 ppm AgNO3) was significant, as the dissociation rate of silver ion concentration correlates to the antibioactivity.

This study uses the conductivity method, Electric Spark Discharge Method, and the electrospinning technique to develop a better silver-based antibacterial agent. The preparation process is free of chemical substances and also conforms to the green energy-saving process. The silver iodide was prepared in an iodine agar medium by using the conductivity method. Multiple bacteriostasis experiments showed that the molds grew in the position with iodine of the culture medium after 6 days, as well as in the position with silver iodide after 10 days. The results prove that silver iodide has better bacteriostatic ability than povidone iodine. The nanosilver colloid was prepared in the PVA solution by using the Electric Spark Discharge Method. UV-Vis, Zetasizer, and SEM-EDX analyses proved that the PVA solution contained nanosilver colloid with good suspension stability. Finally, the electrospinning technique was used to spin the PVA solution with nanosilver colloid into the PVA nanofibrous membrane. According to UV-Vis analysis, the absorption peak of this nanofibrous membrane is about 415 nm, meaning this nanofibrous membrane contains nucleate nanosilver colloid, and is very suitable for antiseptic dressing.

The electrical discharge machining (EDM) system has been proven feasible as a rapid and efficient method for silver nanofluid preparation. This study prepared the silver nano-fluid via EDM and investigated the relationship between its process parameters and product characteristics. The prior study had found that the silver nano-fluid prepared by EDM contained both silver nanoparticles and silver ions. Silver ions had revealed the cause of the high suspension of the silver nanoparticles. To examine the relationship between the stability of silver nanofluid and the process parameters, this study quantified the relationship of process parameters to the material removal rate (MRR) of silver electrode and silver ion output rate (IOR) in the fluid, in order to achieve the most effective process parameter condition. Furthermore, the stability of silver nano-fluid was analyzed by various devices, including UV-Vis spectroscopy, size-distribution, and Zeta-potential analyzer. The effects of MRR, IOR, particle size, Zeta-potential, and optical properties of silver nanofluid under different process parameters are also discussed.