Search

Preparation of pharmaceutical nanosuspensions is a popular technique to increase the dissolution velocity of poorly water-soluble drugs. Subsequent drying into a compaction-ready powder or granule is a critical process due to possible adverse solid characteristics and the risk of growth of nanoparticles. This work evaluated the drying of nanosuspensions via fluid bed granulation with focus on the binder selection and used concentrations, as well as the parameters spray rate and atomization pressure. Design of experiments was used to identify significant parameters. Indomethacin nanosuspensions were prepared by wet media milling and dried on a carrier consisting of lactose, microcrystalline cellulose, and crospovidone with and without additional binder during granulation. Resulting granules were compacted into tablets and their in vitro dissolution performances were characterized. A higher content of binder PVP and a higher spray rate led to less growth of resuspended nanoparticles. Finally, indomethacin nanoparticle tablets showed a superior dissolution performance in contrast to raw indomethacin tablets., (Copyright © 2020 Elsevier B.V. All rights reserved.)

The aim of the research was to investigate the complete process of pellet production in a Wurster fluidized bed coater in order to determine the main factors affecting the migration phenomenon of a soluble API through the ethycellulose film coating (Surelease®) and hence the long-term stability of the controlled release pellets. Guaifenesin (GFN), as BCS class I model drug, was layered on sugar spheres using a binder-polymer solution containing the dissolved GFN. The drug loaded pellets were then coated with Surelease®. The influence of drug loading (4.5-20.0% w/w), curing conditions (40-60°C and dynamic-static equipment), coating level (12-20% theoretical weight gain) and composition of the binder-layering solution (hypromellose versus Na alginate) on process efficiency (RSDW%), GFN content uniformity (RSDC%), GFN solid state (DSC and XRD) and pellet release profiles was evaluated. The effectiveness of the Surelease film was strongly affected by the ability of GFN to cross the coating layer and to recrystallize on the pellet surface. Results indicated that this behaviour was dependent on the polymer used in the binder-layering solution. Using hypromellose as polymer, GFN recrystallized on the coated pellet surface at both drug loadings. The curing step was necessary to stabilize the film effectiveness at the higher drug loading. Increasing the coating level delayed but did not prevent the GFN diffusion. Replacing hypromellose with Na alginate, reduced the migration of GFN through the film to a negligible amount even after six months of storage and the curing step was not necessary to achieve stable controlled release profiles over storage., (Copyright © 2015 Elsevier B.V. All rights reserved.)

In a previous study, hydroxypropyl cellulose (HPC)-based capsular shells prepared by injection molding and intended for pulsatile release were successfully coated with 10mg/cm(2) Eudragit® L film. The suitability of HPC capsules for the development of a colon delivery platform based on a time dependent approach was demonstrated. In the present work, data logging devices (PyroButton®) were used to monitor the microenvironmental conditions, i.e. temperature (T) and relative humidity (RH), during coating processes performed under different spray rates (1.2, 2.5 and 5.5g/min). As HPC-based capsules present special features, a preliminary study was conducted on commercially available gelatin capsules for comparison purposes. By means of PyroButton data-loggers it was possible to acquire information about the impact of the effective T and RH conditions experienced by HPC substrates during the process on the technological properties and release performance of the coated systems. The use of increasing spray rates seemed to promote a tendency of the HPC shells to slightly swell at the beginning of the spraying process; moreover, capsules coated under spray rates of 1.2 and 2.5g/min showed the desired release performance, i.e. ability to withstand the acidic media followed by the pulsatile release expected for uncoated capsules. Preliminary stability studies seemed to show that coating conditions might also influence the release performance of the system upon storage., (Copyright © 2015 Elsevier B.V. All rights reserved.)

Rod-shaped nanocrystalline cellulose (NCC) was prepared from microcrystalline cellulose (MCC) using the purely physical method of high-intensity ultrasonication. Scanning electron microscopy, transmission electron microscopy, and X-ray diffraction was used for the characterization of the morphology and crystal structure of the material. The thermal properties were investigated using thermogravimetric analysis. The reinforcement capabilities of the obtained NCC were investigated by adding it to poly(vinyl alcohol) (PVA) via the solution casting method. The results revealed that the prepared NCC had a rod-shaped structure, with diameters between 10 and 20 nm and lengths between 50 and 250 nm. X-ray diffraction results indicated that the NCC had the cellulose I crystal structure similar to that of MCC. The crystallinity of the NCC decreased with increasing ultrasonication time. The ultrasonic effect was non-selective, which means it can remove amorphous cellulose and crystalline cellulose. Because of the nanoscale size and large number of free-end chains, the NCC degraded at a slightly lower temperature, which resulted in increased char residue (9.6-16.1%), compared with that of the MCC (6.2%). The storage modulus of the nanocomposite films were significantly improved compared with that of pure PVA films. The modulus of PVA with 8 wt.% NCC was 2.40× larger than that of pure PVA., (Crown Copyright © 2011. Published by Elsevier B.V. All rights reserved.)

Cellotriose and cellotetraose analogues carrying cyclohexene rings were developed as molecular probes which are expected to mimic the transition state conformation of hydrolysis by cellulases. The cyclohexene ring was placed at the pyranose ring being expected to locate the -1 subsite of the enzyme. In order to evaluate these probes, sulfur derivatives of cellotriose and cellotetraose were also synthesized as the enzyme tolerant analogues which mimic the stable conformations of the natural cellulose. The binding assays using differential scanning calorimetry revealed that introduction of the cyclohexene ring is effective to the complexation with an endoglucanase, NCE5 from Humicola insolens., (Copyright © 2011 Elsevier Ltd. All rights reserved.)

The synthesis and characterisation of pyridinium porphyrinic chloroacetyl cellulose ester chlorides, where photosensitizing agents are covalently bounded to the polymeric chain, is presented in this paper. First, cellulose was homogenously converted into chloroacetate cellulose ester in DMAc/LiCl solvent by using chloroacetyl chloride. The complete substitution of cellulose was achieved using 7equiv of chloroacetyl chloride for a 2h reaction at room temperature. The absence of base did not prove detrimental to reaction. The grafting of monopyridyltritolylporphyrin onto chloroacetate cellulose ester was then realised by alkylation of the photosensitizer in DMF. These new plastic films were found to be thermostable up to 55 degrees C; higher temperatures led to progressive deacetylation. First results of their photobactericidal activity against Staphylococcus aureus and Escherichia coli strains are very encouraging. Such materials could find applications in medical environments as an alternative to overcome the rampant bacterial multiresistance to classical antibiotics.

Hot-melt extrusion technology was used to produce thin films containing a model drug, lidocaine, and the cellulosic polymers hydroxypropyl cellulose (HPC) and hydroxypropyl methyl cellulose (HPMC). Two film formulations were extruded and compared, one containing only HPC and the other containing HPC:HPMC (80:20). Thermal analysis of the films using differential scanning calorimetry (DSC) suggested that the drug existed in the amorphous condition, which was confirmed by wide angle X-ray diffractometry. Sustained release of the drug was observed from both of the polymer matrices. Dissolution profiles suggested that HPMC retarded the drug release from HPC:HPMC (80:20) films. However, the mechanism of drug release from both of the films was predominantly diffusion of the drug through the polymer matrices. Incorporation of HPMC also increased both adhesive strength and work of adhesion as compared to the HPC-only films.

Chitosan pellets were successfully prepared using the extrusion/spheronization technology. Microcrystalline cellulose was used as additive in concentrations from 70 to 0%. The powder mixtures were extruded using water and diluted acetic acid solution in different powder to liquid ratios. The effects on bead formation using water and different acetic acid concentrations and solution quantities were analysed. Also, the morphological and mechanical characteristics of the obtained beads were investigated. With demineralized water as granulation fluid, pellets with a maximum of 50% (m/m) of chitosan could be produced. The mass fraction of chitosan within the pellets could be increased to 100% by using diluted acetic acid for the granulation step.

A new amphiphilic adsorbent for the removal of low-density lipoprotein (LDL) was prepared according to the literature (Artif. Cells Blood Subs., Immob. Biotechnol. 30 (4) (2002) 285). The effects of sulfonation and grafting time of cholesterol on the swelling property of adsorbent were studied. When sulfonation and grafting time of cholesterol was 3 and 5 h, respectively, the amphiphilic adsorbent had a high adsorption capacity for LDL without significantly adsorbing high-density lipoprotein. The adsorption capacity of the adsorbent for the removal of LDL, total cholesterol (TC) and TG was 1.916, 2.132, 1.349 mg/ml, respectively. Hyperlipidemia rabbits were developed by feeding with fodder containing high content of cholesterol or yolk, which was then perfused with an optimal amount of amphiphilic adsorbent. After 2 h hemoperfusion, the LDL levels decreased from 3.619+/-0.354 to 0.724+/-0.07 mmol/l, which showed that the adsorbent could effectively remove LDL without side effect.

A novel method for the preparation of N-acylchitosan fiber and N-acylchitosan-cellulose fiber is described. Each aqueous solution of sodium N-acetyl and N-propionylchitosan salts in aqueous 14% NaOH was spun through a viscose-type spinneret at 10-15 degrees C into a coagulating bath containing aqueous 10%, H2SO4. 25% Na2SO4 and 1.3% ZnSO4 to afford the corresponding white fiber. By the same method, a clear solution of sodium N-acetyl and N-propionyl chitosan salts were respectively mixed with sodium cellulose xanthate in aqueous 14% NaOH and spun to afford the corresponding white N-acylchitosan-cellulose fiber. Their filament tenacity and elongation values were 0.4-0.7 times as large as cellulose. These fibers were digestible in reactions by chitinase and lysozyme, and the digestibility was controlled by the structure of the N-acyl group.