Search

Although the production of several founder animals (F0) for gene editing in livestock has been reported in cattle, very few studies have assessed germline transmission to the next generation due to the long sexual maturation and gestation periods. The present study aimed to assess the germline transmission of MSTN mutations (-12bps deletion) in MSTN mutant F0 male and female cattle. For this purpose, oocytes and semen were collected after the sexual maturation of MSTN cattle, and embryos produced by in vitro fertilization were analyzed. In addition, the embryos were subjected to additional gene (PRNP) editing using electroporation. Embryos produced by in vitro fertilization with MSTN male and female cattle were transferred to a surrogate, and one calf was successfully born. MSTN heterozygous mutation was shown by sequencing of the F1 calf, which had no health issues. As a further experiment, using electroporation, additional gene-edited embryos fertilized with the MSTN male sperm showed a high mutation rate of PRNP (86.2 ± 3.4%). These data demonstrate that the cattle produced through gene editing matured without health issues and had transmitted MSTN mutation from the germ cells. Also, additional mutation of embryos fertilized with the MSTN male sperm could enable further mutagenesis using electroporation.

Best estimate plus uncertainty (BEPU) is a promising approach to the safety analysis of nuclear reactors, and the uncertainty calculation is a very important concern about it. BEPU ensures realistic safety margins and secures higher reactor effectiveness by adopting best-estimate codes and realistic input data with uncertainties, whereas the previous conservative analysis generates excessive conservatism by considering each input parameter separately. A loss of flow accident (LOFA) of a 5 MW open-pool type research reactor was selected as a sample problem for a BEPU uncertainty assessment. We selected the failures of all primary cooling system (PCS) pumps, which would cause the abrupt reduction of flow and the reversal of core flow. The significant contributors to the reactor safety were identified and then input sets were sampled. For the uncertainty evaluation, 124 calculations were performed. This is the number of code runs required for a 95%/95% level with the 3rd order Wilk’s formula. The MOSAIQUE software developed by Korean Atomic Energy Research Institute (KAERI) was used for automated sampling of the uncertainty parameters, a global uncertainty calculation, and post processing of the results. The critical heat flux ratio (CHFR) and the fuel centerline temperature (FCT) were calculated at the 95%/95% level and were compared with those from conservative analyses. In addition, the impact of each design variables on the safety parameters was estimated by sensitivity analysis.

Mesenchymal stem cells (MSCs) promote therapeutic angiogenesis to cure serious vascular disorders. However, their survival period and cytokine-secretory capacity are limited. Although hepatocyte growth factor (HGF) can accelerate the rate of angiogenesis, recombinant HGF is limited because of its very short half-life (

In animal reproduction technologies, the in vitro embryo culture system has advanced over the past few decades. However, in vitro cultured embryos still have reduced functional and physiological abilities compared with those from in vivo conditions, and many factors of oviduct and uterine environments have not yet been revealed. Here, we demonstrated the in vitro culture of domestic goat (Capra hircus) embryos using two types of culture media, modified synthetic oviductal fluid (mSOF) and a two-step chemically defined medium (DI/II). To obtain parthenogenetic goat embryos, oocytes were matured in vitro in tissue culture media-199 supplemented with 10% fetal bovine serum for 22 to 24 hours, and activated with 5 μM, Ca(2+) ionomycin for 4 minutes, followed by 1.9 mM, 6-dimethylaminopurine treatment for 4 hours. After 2 days of embryo culture in different culture media, there were no significant differences in cleavage rates (96.6% vs. 95.4% in mSOF vs. DI/II, respectively). However, the DI/II group showed improved development competence to blastocysts (64.6% vs. 82.3% in mSOF vs. DI/II, respectively) and the total cell number of blastocysts (144.3 ± 9.2 vs. 264.4 ± 15.2 in mSOF vs. DI/II, respectively) at Day 7. After the cryopreservation of early-stage blastocysts at Day 6 via the conventional slow-freezing procedure, the surviving embryos were analyzed. The re-expansion rate after freezing and thawing was significantly higher in DI/II (39.66% vs. 67.69% in mSOF vs. DI/II, respectively), but there were no statistical differences in total cell numbers (142.3 ± 12.1 vs. 172.1 ± 11.6 in mSOF vs. DI/II, respectively), apoptotic index (4.9 ± 0.8% vs. 3.8 ± 0.7 in mSOF vs. DI/II, respectively), and the gene expression levels (BAX, GLUT1, MnSOD, and OCT4) among the re-expanded blastocysts. Overall, our data reported that the defined in vitro culture media for goat embryos were established with high efficiency, which will be very useful for goat embryo production.

By considering the requirements for a DEMO-relevant blanket concept, Korea (KO) has proposed a He cooled molten lithium (HCML) test blanket module (TBM) for testing in ITER. A performance analysis for the thermal–hydraulics and a safety analysis for the KO TBM have been carried out using a commercial CFD code, ANSYS-CFX, and a system code, GAMMA (GAs multicomponent mixture analysis), which was developed by the gas cooled reactor in Korea. To verify the codes, a preliminary study was performed by Lee using a single TBM first wall (FW) mock-up made from the same material as the KO TBM, ferritic martensitic steel, using a 6 MPa nitrogen gas loop. The test was performed at pressures of 1.1, 1.9 and 2.9 MPa, and under various ranges of flow rate from 0.0105 to 0.0407 kg/s with a constant wall temperature condition. In the present study, a thermal–hydraulic test was performed with the newly constructed helium supplying system, in which the design pressure and temperature were 9 MPa and 500 °C, respectively. In the experiment, the same mock-up was used, and the test was performed under the conditions of 3 MPa pressure, 30 °C inlet temperature and 70 m/s helium velocity, which are almost same conditions of the KO TBM FW. One side of the mock-up was heated with a constant heat flux of 0.3–0.5 MW/m 2 using a graphite heating system, KoHLT-2 (Korea heat load test facility-2). Because the comparison result between CFX 11 and GAMMA showed a difference tendency, the modification of heat transfer correlation included in GAMMA was performed. And the modified GAMMA showed the strong parity with CFX 11 calculation results.

The forces acting on a bubble were analyzed to determine the criteria for bubble departure and lift-off from a heated wall. Mechanistic models for the bubble departure and lift-off diameters were developed from the analysis results to predict the evaporation heat flux under low heat flux and low flow velocity conditions. The developed model for the departure diameter depends strongly on the contact angle, but the model for the lift-off diameter was found to be a function of the lift-off number, which indicates the ratio between the shear lift force and the growth force. Wall boiling experiments were performed to measure bubble departure and lift-off diameters using digital image processing. From the experimental data, the developed models were validated, and the results showed good agreement between the experimental data and the predicted diameters.