Search

Bio-based additives received significant attention in pulp and paper properties improvement. For this, the most cited biochemical Cellulose Nano Fibrils (CNFs) and Cationic Starch (CS) were experimentally compared with the most declared synthetic chemical, Cationic Polyacrylamide (CPAM). SEM images showed better paper surface filling by the utilization of the chemicals. The three studied polymers, in solely or combination mechanism, improved mainly bagasse pulp and paper properties compared to the blank sample, except for pulp drainage, which decreased by CNFs to lower volumes presumably due to its intrinsic characteristics. Cationic polymers (CP) compared to CP/CNFs approaches increased pulp retention and drainage but decreased paper density and strengths. The best pulp retention and drainage achieved by CS followed by CPAM, while paper air persistency, density, and strength properties evaluated highest by CP/CNFs followed by CNFs. Generally, CS revealed a more significant improvement in pulp and paper properties than CPAM either with or without CNFs.

As a crucial biomarker for some diseases, the determination of cholesterol in human serum is of great significance for the diagnosis and prevention of these diseases. Hence, a portable cholesterol detection method is necessary for clinical and domestic applications. Here, a portable paper sensor was designed for cholesterol detection by modifying screen-printed electrode (SPE) with nanoporous gold (NPG). To achieve the reliable cholesterol detection, a synergistic strategy was proposed based on the oxidation of cholesterol by cholesterol oxidase (ChOx) and the reduction of oxidation product (H2O2) by NPG. Compared to existing electrochemical sensors, the resulting paper sensor exhibited a wider linear response in a range from 50 μM to 6 mM as well as a higher sensitivity of 32.68 μA mM−1 cm−2 with a lower detection limit of 8.36 μM. Moreover, the portable paper sensor presented strong anti-interference capability and stability in the detection of cholesterol in human serum, and the data detected by the portable paper sensor were consistent with that obtained by an automatic biochemical analyzer. These unique performances confirmed that the proposed paper sensor was a sensitive, reliable, and portable cholesterol detection method, making it a good choice for cholesterol detection.

Recently, cellulose paper based triboelectric nanogenerators (CPTENGs) has gained widely attention due to the development of wearable, green and miniaturized electronic products. Modification of cellulose fibers or paper is a feasible method to improve the output performance of CPTENGs, however, the simple and effective routes to improve the triboelectric property of cellulose paper still remain a challenge. Herein, we report a simple method to prepare PEO/cellulose composite paper (PEO/CCP) via mixing polyethylene oxide (PEO) with cationic cellulose fibers. Benefiting from amino groups and PEO, the composite paper exhibits higher triboelectric positive property and triboelectric charge density, thereby endowing PEO/CCP based TENG with outstanding output performance. The voltage, current and power density peak values of PEO/CCP based TENG exhibited linear relationship with amino groups content; in this instance, the performance of the TENGs can be readily adjusted by the amino groups. The voltage, current and power density of PEO/CCP based TENG can be up to 222.1 V, 4.3 μA, and 217.3 mW•m

Developing a feasible and low-cost approach to fabricate recyclable, UV-shielding, biodegradable as well as water- and oil-resistant coating for paper substance is still a challenge. Herein, novel full-biobased chitosan-derived cardanol glycidyl ether (CS-xCGE, x = 1/8, 1/4, 1/2, and 1) coatings with different contents of cardanol glycidyl ether (CGE) were developed for paper substance via the ethoxylation of cardanol and sequent addition with chitosan in a one-pot process. Benefiting from the hydrophobicity and ultraviolet resistance of CGE, the resultant CS-CGE (x = 1) coated paper exhibited not only remarkable oil resistance (kit rating value of 11/12), but also water resistance (Cobb 60 value of 5.78 g/m

Funding Information: The financial support of the Austrian Federal Ministry of Digital and Economic Affairs and the National Foundation for Research, Technology and Development , Austria, is gratefully acknowledged. We also thank the industrial partners Mondi, Canon Production Printing, Kelheim Fibres, and SIG Combibloc for their support. Publisher Copyright: © 2021 Copyright: Copyright 2021 Elsevier B.V., All rights reserved. Hydrophobization of cellulosic materials and particularly paper products is a commonly used procedure to render papers more resistant to water and moisture. Here, we explore the hydrophobization of unsized paper sheets via the gas phase. We employed three different compounds, namely palmitoyl chloride (PCl), trifluoroacetic anhydride/acetic anhydride (TFAA/Ac2O)) and hexamethyldisilazane (HMDS) which were vaporized and allowed to react with the paper sheets via the gas phase. All routes yielded hydrophobic papers with static water contact angles far above 90° and indicated the formation of covalent bonds. The PCl and TFAA approach negatively impacted the mechanical and optical properties of the paper leading to a decrease in tensile strength and yellowing of the sheets. The HMDS modified papers did not exhibit any differences regarding relevant paper technological parameters (mechanical properties, optical properties, porosity) compared to the non-modified sheets. XPS studies revealed that the HMDS modified samples have a rather low silicon content, pointing at the formation of submonolayers of trimethylsilyl groups on the fiber surfaces in the paper network. This was further investigated by penetration dynamic analysis using ultrasonication, which revealed that the whole fiber network has been homogeneously modified with the silyl groups and not only the very outer surface as for the PCl and the TFAA modified papers. This procedure yields a possibility to study the influence of hydrophobicity on paper sheets and their network properties without changing structural and mechanical paper parameters.

There is a pressing need around the world to develop novel functional biodegradable materials to separate oil/water mixtures and emulsions completely. Recently, superhydrophilicity and underwater superoleophobicity materials have been attracted attention due to their high efficiency in oil/water separation. However, it is still a challenge to prepare materials that combine oil/water separation and water purification in an environment-friendly way. In this work, biodegradable starch-based nanospheres (SNPs) coated filter paper was prepared in a low-cost, simple, and environmentally friendly manner. The SNPs coating could not only help to change the wettability of the substrate material but also build the hierarchical micro and nano structures which are conducive to separation and purification process. After modification by coating SNPs, the filter paper exhibited excellent performance in a wide range of oil/water mixtures or emulsions separation and the wettability of the filter paper could be regulated by adjusting the pH value. The modified filter paper presented good recyclability after several separation process. Furthermore, the as-prepared filter paper could also remove water-soluble contaminants during the oil/water separation process, thus realizing to combine separation and purification process in one single step. This biodegradable starch-based separating material with good separation performance, stability and recyclability has significant application potential in practical separation and purification process.

Starch and derivatives thereof have proven their usefulness in paper coating processes. Among these derivatives, cationic starch has been widely used in the paper industry as a flocculation, dispersion and ink fixing agent. In another context, nanoscale cellulosic materials have been shown to improve the strength, retention of fillers, the barrier properties of packaging paper products, and printing qualities. This review summarizes the recent studies on the general components used in paper coating, describes the conventional and alternative synthetic processes of cationic starches and nanocellulose, and deals with their current and potential applications in papermaking, focusing primarily on surface treatments. Moreover, environmental applications have been considered to expand the understanding and usefulness of these materials. Further research on modified polysaccharides is encouraged to replace, in a feasible way, petro-based components of coating formulations, and to provide paper surfaces with new properties.

Biobased packaging materials derived from carbon-neutral feedstocks are sustainable alternatives to conventional fossil-based polymers. In this study, a method was developed to prepare paper-sheets derived from Miscanthus × giganteus cellulose fibers for potential food contact applications. The papers were hydrophobized with modified lignin extracted (EL) from Miscanthus × giganteus biomass and commercial Kraft alkali lignin (CL) through hydroxyethylation with ethylene carbonate, followed by esterification with propionic acid. The esterified lignin (10 % w/w) and cellulose acetate (5 % w/w, based on lignin content) were dissolved in acetone and applied as a coating on the miscanthus paper sheets. The esterified lignins were characterized using FTIR, NMR, DSC, TGA, and elemental analyses. The uncoated and coated paper-sheets had contact angle values 52.4° and130°, respectively, indicating an increased surface hydrophobicity of the coated paper samples. The water vapor transmission rate decreased significantly from 213.7 (uncoated paper-sheet) to 63.3 g/m

A green and facile method was proposed to prepare robust and fully bio-based modified paper in this study, which involved in layer-by-layer deposition of chitosan (CS) and mussel adhesive protein-mimetic polymer (dopamine-grafted carboxymethyl cellulose, CMC-g-DA) on paper surface and subsequent oxidative cross-linking by sodium periodate. The mechanical, barrier and antibacterial properties of the cross-linked multilayer-modified paper significantly improved with the increased bilayer numbers. Compared with unmodified paper, cross-linked (CS/CMC-g-DA)

Competitive immunoassays comprise the standard means of detecting small molecules. However, conventional methods using microwells are difficult to apply during point-of-care tests (POCT) because they require complicated handling and are time consuming. Although paper-based analytical devices (PAD) have received considerable focus because of their rapid and straightforward operation, only a few devices have been proposed for competitive immunoassays. Herein, we describe a novel universal PAD format with a 3-dimensional configuration for competitive immunoassays that rapidly and sensitively detects small molecules. The proposed device comprised a layered structure with uniform color formation and high capture efficiency between antigen and antibody that results in rapid and reproducible results. The device rapidly (90 s) assayed biotin as a model target, with a limit of detection (LOD) of 5.08 ng mL−1, and detected progesterone with an LOD of 84 pg mL−1 within 5 min. Moreover, sample volumes and reagent consumption rates were minimized. Thus, our device could be applied to competitive immunoassays of various small molecules in POCT.

Recently, the interest in active packaging utilization has increased with population growth, food demand and new consumer trend like food delivery services. This new system, however, requires the use of additives to extend the food product quality and safety as well as in maintaining the shelf-life. This study was to prepare the antimicrobial paper from I. cylindrica coated anionic nanocellulose crosslinked cationic to create a system with the ability to actively control microbe growth in the packaging materials. The process involved pulping of I. cylindrica using semi-chemical and soda chemical method. The antimicrobial paper was prepared by printing the pulp suspension in 60 g/m2 grammage in mold followed by the spray of anionic nanocellulose and subsequent soaking of the paper in cationic solution. The results showed the I. cylindrica paper coated anionic nanocellulose crosslinked with H+ and Al3+ cations were successfully produced. The paper produced was also observed to have antimicrobial activity against Gram-negative of E. coli and S. typhi as well as Gram-positive of S. aureus and B. subtilis bacteria. Furthermore, the best coating method was found on antimicrobial paper coated anionic nanocellulose crosslinked Al3+ as evidenced by smoother and compact surface structure.

There is growing demand for simple to operate, sensitive, on-site quantitative assays to investigate concentrations of drug molecules in pharmaceutical preparations for quality assurance. Here, we report on the development of two colorimetric analysis methods for the study the antibiotic doxycycline hyclate (DOX) and the nasal decongestant oxymetazoline hydrochloride (OXY), in solution as well as in their respective formulations. We compare a UV/vis spectrophotometry method with a color change recorded on a microfluidic paper-based analytical device (μPAD). Detection is based on the pharmaceutical compounds coupling with diazotized 4-aminoacetophenone (DAAP) under alkaline conditions to produce colored azo-dye products. These azo-compounds were monitored by absorbance at 425 nm for DOX and 521 nm for OXY, with linear calibration graphs in the concentration range of 0.5–35 mg L−1 (DOX) and 1.0–40 mg L−1 (OXY) and limits of detection of 0.24 mg L−1 (DOX) and 0.32 mg L−1 (OXY). For the μPAD method, color intensity was measured from photographs and a linear increase was observed at concentrations from above approximately 15 mg L−1 for both compounds and up to 35 mg L−1 for DOX and 40 mg L−1 for OXY. The developed methods were also applied to the formulated pharmaceuticals and no interference was found from the excipient. Thus, the paper-based device provides an inexpensive, simple alternative approach for use outside centralized laboratories with semi-quantitative capability.

In this work, we prepared novel cellulosic paper by incorporating tannin into the kraft pulp for potential application in active food packaging. The kraft pulp fibers were firstly periodate oxidized to obtain the dialdehyde cellulosic fibers, and then reacted with varied dosages of tannin to incorporate them into the fibers by covalent bondings between aldehyde groups on cellulose and active hydrogen on tannin. Handsheets were prepared using the tannin incorporated fibers through papermaking process and the properties were characterized. The percentage of tannin in the paper increased with the increase of the tannin dosage. FT-IR spectra confirmed the successful incorporation of tannin into the cellulosic fibers. It was found that paper after incorporation of tannin turned to be surface hydrophobic with contact angles higher than 90°, which may probably due to the covalent bonds between tannin and cellulose. The handsheets show high antioxidative and UV-shielding properties, which both increased with the increase of the tannin percentage in the paper. Water vapor transmission rate (WVTR) decreased after the incorporation of tannin, and this could facilitate its application in food packaging. The breaking length of tannin incorporated paper decreased insignificantly, less than 10% with the tannin percentage as high as 45%.

A novel all-in-one paper-based sampling concept for mass spectrometric bottom-up protein analysis is here demonstrated in a chip format integrating instant immunocapture, protein reduction, - alkylation and tryptic digestion all in-device. Conventional laboratory grade filter paper was coated with the polymer 2-hydroxyethyl methacrylate-co-2-vinyl-4,4-dimethyl azlactone (pHEMA-VDM) with a subsequent covalent immobilization of the monoclonal antibody E27 targeting the biomarker human chorionic gonadotropin (hCG). In-device protein reduction and alkylation was optimized with regards to reagent concentration and reaction pH. The sampling concept showed a high degree of performance between 10 and 1000 ng/mL (R2 > 0.99) by a five-point calibration curve sampled with hCG spiked to human serum samples and freshly collected whole blood samples, respectively. LOD (experimentally obtained at 100 pg/mL (2.64 pM/0.9 IU/L)) was demonstrated to be up to ten times lower with more than six times faster sample preparation than what has previously been reported for on-paper analysis of hCG in human serum samples.

Made available in DSpace on 2021-06-25T10:45:32Z (GMT). No. of bitstreams: 0 Previous issue date: 2021-01-25 Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP) Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq) Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES) Fundação de Amparo à Pesquisa do Estado de Minas Gerais (FAPEMIG) Lactose (LAC) is a disaccharide - major sugar, present in milk and dairy products. LAC content is an important indicator of milk quality and abnormalities in food industries, as well as in human and animal health. The present study reports the development of an innovative imprinted voltammetric sensor for sensitive detection of LAC. The sensor was constructed using electropolymerized pyrrole (Py) molecularly imprinted polymer (MIP) on graphite paper electrode (PE). The MIP film was constructed through the electrosynthesis of polypyrrole (PPy) in the presence of LAC (template molecule) on PE (PPy/PE). To optimize the detection conditions, several factors affecting the PPy/PE sensor performance were assessed by multivariate methods (Plackett–Burman design and central composite design). Under optimized conditions, the proposed analytical method was applied for LAC detection in whole and LAC-free milks, where it demonstrated high sensitivity and selectivity, with two dynamic linear ranges of concentration (1.0–10 nmol L−1 and 25–125 nmol L−1) and a detection limit of 0.88 nmol L−1. The MIP sensor showed selective molecular recognition for LAC in the presence of structurally related molecules. The proposed PPy/PE sensor exhibited good stability, as well as excellent reproducibility and repeatability. Based on the results obtained, the PPy/PE is found to be highly promising for sensitive detection of LAC. Analytical Chemistry Department Institute of Chemistry São Paulo State University (UNESP), 55 Prof. Francisco Degni St., São Paulo State Institute of Exact and Natural Sciences of Pontal Federal University of Uberlandia, 1600 20 St., Ituiutaba, Minas Gerais State Bioenergy Research Institute (IPBEN) São Paulo State University (UNESP), 55 Prof. Francisco Degni St., São Paulo State Analytical Chemistry Department Institute of Chemistry São Paulo State University (UNESP), 55 Prof. Francisco Degni St., São Paulo State Bioenergy Research Institute (IPBEN) São Paulo State University (UNESP), 55 Prof. Francisco Degni St., São Paulo State FAPESP: 2017/25329–6 FAPESP: 2018/12131–6 FAPESP: 2019/13818–8 CNPq: 408783/2018–4 CNPq: 443315/2014–0 CNPq: 447668/2014–5 CAPES: 88887.368610/2019–00 FAPEMIG: APQ-02078-15 FAPEMIG: APQ-02905-15

This work presents an unconventional use of capacitively coupled contactless conductivity detector (C4D) for detection of gas absorption by moist paper with potential application for chemical analysis. To be suitable for measuring conductivity of moist paper absorbent, the C4D sensor was therefore designed in planar configuration. A layer of dry filter paper, only 20 mm × 25 mm in size, was placed on the C4D sensor and the device installed inside a specifically designed vaporization chamber. A vial (16 mm i.d., 8 mm high) containing a 150-μL solution of sodium bicarbonate was placed alongside. The filter paper was loaded with 110 μL of deionized water through an injection hole in the cover lid. A 100-μL aliquot of 2 M hydrochloric acid solution was directly dispensed into the vial through a second hole in the lid to generate CO2 gas from the bicarbonate solution. It was observed that the C4D sensor gave real-time response that corresponded to the absorption of the gas and subsequent production of H+ and HCO3− in the moist paper. The monitored signal reached a constant value at 160 s after the addition of the acid. Chemistry of the absorption process and equivalent circuit for the C4D are proposed. Direct measurement of cement powder was chosen to demonstrate the potential use of this device for quantifying the CaCO3 content of the cement. The calibration curve for 0.5–3 mg CaCO3 was linear for signals recorded at 160 s: Vdc = (0.172 ± 0.005) · (mg CaCO3) + (0.016 ± 0.009), with coefficient of determination of 0.9965. Linear calibrations were also observed when the signals were monitored at various time less than 160 s. The limit of quantitation (3 SD of intercept/slope) was 0.17 mg CaCO3. The method provided acceptable precision with %RSD of 4.6 (2 mg CaCO3, n = 10).

Polygalacturonase (PG) activity in plants can serve as an important index for plant disease. However, the conventional method to detect PG activity is a complex process and requires a skilled technician and expensive analytical equipment. In this study, a paper-based colorimetric sensor was developed based on the principle of the ruthenium red (RR) dye method for easy and simple measurement of PG activity. The proposed paper-based sensor has a three-layer structure for detection of PG activity in samples. The sensor sensitivity was enhanced by optimizing the pH of the sodium acetate buffer used in polygalacturonic acid (PGA)-RR complex formation and the reaction temperature for PG and the PGA-RR complex. Further, for quantitative analysis of PG activity, Delta RGB analysis was conducted to detect color changes in the sensing window of the sensor. Results presented that the linear measurement range of the paper sensor was 0.02-0.1 unit with the limit of detection of 0.02 unit, which showed a similar detection range, but a lower detection limit, compared to the spectrophotometry. Furthermore, PG activity based on culture condition was measured using samples from Sclerotium cepivorum to verify the potential application of the developed paper-based sensor in the field. The measured activity showed no statistically significant difference from the values obtained from the spectrophotometry at 95% confidence level. Therefore, the paper-based colorimetric sensor can be used to predict plant diseases in Allium crops during the stage of pathogen invasion, potentially contributing to the improvement of crop production.

In this paper, nanochitin was used as an alternative natural nanomaterial to combine with cellulose fibers for fabricating high-strength paper. Two typical chitin nanowhiskers having contrasting sign of surface charge were compared to evaluate the enhancement performance on paper in details. The results show that nanochitin with positive charges on the surface has a significant effect on the strength properties of the prepared paper, especially on wet strength. When the dosage of chitin nanowhiskers was 2%, the wet strength index was increased to 2.48 N·m/g, which is important for paper-based analytical devices with the common use in liquid analysis. Typical colorimetric glucose assays were successfully performed, suggesting the improved analytical performance on these prepared paper.

China, a big paper-making country, produced hundreds of millions of tons of waste paper which contain a lot of fiber every year. Cellulose nanocrystals were extracted from recycled waste paper which can be a high value utilization of secondary fiber. In this paper, cellulose nanocrystals were successfully extracted from waste paper fibers via two different systems, sulfuric acid hydrolysis (SCNCs) and one-step ammonium persulfate (APS) oxidation (OCNCs). This not only broadened the methods of extracting CNCs from waste paper, but also improved the dispersion and reactivity of CNCs. The CNCs products were investigated by FT-IR spectroscopy for functional group structure, X-ray diffraction for crystal structure, TG-DTG for thermal stability and scanning electron microscope, transmission electron microscope for morphology. The results showed that both OCNCs and SCNCs were a rod-like structure. The crystallinity of OCNCs and SCNCs increased to 72.45 and 77.56, but with a low yield of 22.42% and 41.22%, respectively. The result also suggested H2O2 formed by decomposition of APS, selectively oxidized the hydroxyl on the C6 in cellulose to carboxyl, introduced 0.57 mmol/g carboxyl. Successful preparation of CNCs extracted from waste paper can effectively utilize the fiber resources in waste paper, thus transforming into higher economic benefits.

Paper-based microfluidic device was designed with wax-printing to combine potentiometric, fluorimetric and colorimetric detection zones. This newly developed trimodal paper chip has been used for on-site determination of ketamine hydrochloride (KET) as a date rape drug in beverages. The device employed polyaniline nano-dispersion as conducting polymer in ion sensing paper electrodes designed to fit USB plug connector. Carbon dots-gold nanoparticles and cobalt thiocyanate were used in fluorescence and color detection zones, respectively. Cellular phone's camera facilitated the on-site fluorimetric and color detection. The implemented trimodal detection system exhibited specificity for KET detection in the presence of several other beverage interferences i.e., biogenic amines. This innovative sensor brings together analytical figures of merit for effective KET detection in single aliquot of spiked beverages. The proposed paper-based chip also fulfils WHO criteria for point-of-care devices posing the proposed trimodal paper device as an active part for rapid, on-site drug diagnostics and to be applied further for other similar drugs.

Free proline, termed proline, is a biomarker used for diagnosing drought stress in plants. A previously developed proline–ninhydrin reaction-based paper sensor could quickly and easily detect proline, but it was limited by low sensitivity. In this study, we developed an enclosed multilayer paper-based microfluidic sensor with high sensitivity for the quantitative detection of proline in plants. The multilayer paper-based sensor was manufactured using simple wax printing and origami methods, and contained an internal mixing channel to allow good mixing of the proline with ninhydrin, increasing the proline–ninhydrin reactivity and providing accurate and sensitive proline detection. By preloading ninhydrin onto the sample loading area, uniform coloration of the sensing window was achieved, allowing quantitative analysis of various proline concentrations using a constant reaction time. Only the sensing window and sample loading area were exposed to limit sample evaporation and contamination from the external environment. The LOD of the fabricated sensor was 23 μM, which is approximately 29-fold lower than that of the previously proposed paper sensor (657 μM). Samples were extracted from A. thaliana plants subjected to drought stress for proline detection. The proline concentrations measured using the developed paper sensor and a spectrophotometric method were not statistically significant at a confidence level of 95%. Therefore, the developed sensor can be applied to measure proline concentrations precisely in the field with a low detection limit. The developed paper-based sensor can be used to detect the early stages of drought in plants and thus improve crop productivity.

This work presents a novel development that exploits the concept of in-situ gas-separation together with a specific enzymatic colorimetric detection to produce a portable biosensor called “Blood Alcohol Micro-pad” for direct quantitation of ethanol in whole blood. The thin square device (25 mm × 25 mm × 1.8 mm) comprises two layers of patterned filter paper held together with a double-sided mounting tape with an 8-mm circular hole (the headspace). In operation, the reagent is deposited on one layer and covered with sticky tape. Then 8 μL of a blood sample is dispensed onto the opposite layer and covered with sticky tape. Diffusion of ethanol across the 1.6 mm narrow headspace permits selective detection of ethanol by the enzymatic reagents deposited on the opposite layer. This reagent zone contains alcohol oxidase, horseradish peroxidase and 2′-azino-bis (3-ethylbenzothiazoline-6-sulfonic acid) diammonium salt, as the chromogenic reagent. The color intensity, measured from the recorded digital image, resulting from the enzymatic assay of ethanol, correlates with the concentration of blood alcohol. The results obtained with spiked mice and sheep blood samples, using an external calibration in the range of 1–120 mg dL−1ethanol, gave recoveries of 93.2–104.4% (n = 12). The “Blood Alcohol Micro-pad” gave good precision with %RSD

Cytochrome P450 (CYP450), and in particular CYP3A4, is the most abundantly expressed CYP450 isozyme implicated in many drug-drug and medicinal plant-drug interactions. Therefore, incorporation of CYP3A4 enzyme screening at an early stage of drug discovery is preferable in order to avoid enzymatic interactions. Here we present for the first time a paper-based CYP3A4 immobilized sol-gel-derived a platform using resorufin benzyl ether as a fluorogenic enzyme substrate used to investigate enzyme activity. The fluorescence intensity of the product can be simply quantified by using a handheld digital microscope and an image analysis software. The limit of quantitation was 0.35 μM with good precision (RSDs 0.05), while offering simplicity and lower cost. Kinetic parameters of the immobilized CYP3A4 in sol-gel coated paper were calculated from the Lineweaver-Burk plot, including Michaelis constant (Km) and maximum velocity (Vmax), which were 2.71 ± 0.35 μM and 0.43 ± 0.05 μM/min, respectively. Moreover, a functional test of these devices was conducted by assessments of known CYP3A4 inhibitors (i.e. ketoconazole, itraconazole) and inducers (i.e. phenytoin, carbamazepine). To further demonstrate the broad range of uses, the devices were utilized to assay plant extracts i.e. Areca catechu seeds, Camellia sinensis leaves, Eclipta prostrata aerial part, providing results in good agreement with previous studies. Furthermore, the sol-gel immobilized enzyme stored at 4 °C can increase storage stability, offering the activity of 86.3 ± 0.4% after 3-weeks storage, equivalent to the activity of the free enzyme solution after 1-week storage. The developed paper-based devices offer versatility, portability and low-cost.

In this study, we developed a point-of-care assay platform with simultaneous detection and self-calibration capabilities for multiple targets based on a microfluidic paper-based analytical device (μPAD). This system is easily manufactured using a wax printing method on chromatographic paper. The design pattern consists of a zone of detection and a calibrant zone for controlled loading using wax barriers with different thicknesses. We showed the utility and applicability of this approach by a proof-of-concept study for two clinically important markers: glucose and lactate. With the naked eye, the results could be fully distinguished and recorded to evaluate the analytical performance with a flatbed scanner. The detection limits of glucose and lactate were 0.3125 mM and 0.2975 mM, respectively, and simultaneous detection was possible from a small sample (0.4 μL) with high sensitivity. Furthermore, this device has a self-calibration function, which minimizes the influence of environmental conditions (i.e., ambient light intensity, temperature, humidity, and pressure). Therefore, the developed multiplex paper-based device is promising for clinical multianalyte point-of-care testing since it is easy to manufacture, cost-effective, user-friendly, and highly sensitive.

A novel 3D paper-based microfluidic screen-printed electrode (SPE) composed of two layers was constructed by photolithography and screen-printing technology. Aldehyde functionalized hydrophilic zone of the counter and reference electrodes layer was prepared for glucose oxidase immobilization. Highly conductive Prussian blue deposited reduced graphene oxide-tetraethylene pentamine (rGO-TEPA/PB) modified paper working electrode layer can be used as an electrochemical sensitive membrane for quantitative detection of hydrogen peroxide (H2O2), which was the enzyme-catalyzed reaction product. Therefore, this 3D paper-based microfluidic electrochemical biosensor can be used for quantitative detection of glucose. Under optimum conditions, the proposed biosensor can be used for quantitative determination of glucose over a wide linear range of 0.1 mM∼25 mM with detection limit of 25 μM. Finally, the 3D paper-based microfluidic electrochemical biosensor was applied to determine glucose in human sweat and blood, and the obtained results were in good consistency with values measured by Roche's blood glucose meter. In addition, the proposed 3D paper-based electrochemical device showed good repeatability, stability, and anti-interference, which would be of great potential to monitor glucose in complex biological fluids.

Preservation of paper-based historical artifacts against deterioration due to the presence of bacteria and fungi colonies has been one of the major issues for the importance of protecting the cultural heritage of humankind. Advances in nanotechnology have enabled the implementation of nanomaterials for this purpose. In this work, calcium/chitosan nanoparticles (Ca/CS NPs) were prepared and well-characterized to investigate their potential as a novel approach for preserving paper-based documents. Following the fundamental characterizations, it was found that Ca/CS NPs are spherical nanoparticles with ~65 nm average size and homogenous dispersion (PdI: 0.2). Besides, minimum inhibition concentration results revealed that Ca/CS NPs show a superior antimicrobial effect against specific bacteria and fungi strains commonly found on paper documents compared to the effect of bare chitosan nanoparticles (CS NPs). After the deposition of Ca/CS NPs onto the paper the pH level was increased and stabilized, and only a limited amount of microbial colony formation was observed for up to 20 days. Moreover, molecular docking analysis provided a better insight into the antibacterial and antifungal activities of these nanoparticles. The antimicrobial activity of CS NPs and Ca/CS NPs was investigated through their interactions with E. coli DNA gyrase B and C. albicans dihydrofolate reductase. The binding modes and all possible interactions of active sites were confirmed by in silico molecular docking method. Collectively, our findings revealed that the formulated Ca/CS NPs are promising candidates for preserving paper documents.

Field-amplified stacking (FAS) is a commonly used method for enhancing the sensitivity of charged species from low conductive media in capillary electrophoresis. FAS also showed significant sensitivity enhancement effect on a uniform paper fluidic channel by proper design of the electrolyte. In this paper, a novel method of introducing electric field gradient is proposed by geometry design of a 2D paper fluidic channel, and field amplification effect was successfully demonstrated with reduced requirement on the sample's conductivity. Sensitive colorimetric detection of microalbuminuria (MAU) from urine samples was demonstrated by mobile phone camera. Experimental results showed that, with active electric field motivation, up to 93.5% of the loaded protein probe could be effectively transferred and stacked into a narrow band on the newly designed paper fluidic channel. A limit of detection (LOD) of 6.5 mg‧L−1 HSA was achieved with a dynamic range of 10–300 mg‧L−1 (linear in the range of 10–100 mg‧L−1, R2 = 0.991). Combined with selective staining of albumin with bromophenol blue (BPB), the established method was applied to the detection of MAU from clinical urine samples, and consistent results with that of the clinical method were obtained. With this paper-based analytical device (PAD), MAU from highly conductive urine samples can be directly loaded and detected without any pretreatment. This method provides a way to develop highly sensitive point-of-care test (POCT) for rapid screening of some diseases.

Microfluidic paper-based analytical devices (μPADs) as a potentially powerful analytical platform have recently gained significant attention for on-site monitoring of heavy metal ions, which are one of the most significant environmental concern because of non-degradability and high toxicity. The commonly applied μPADs suffers from some defects, such as heterogeneous deposition of reagent, resulting in poor detection limits and low sensitivity. So, in this work, a three-dimensional origami μPAD combined with PVC Membrane was developed, which can manage problems of movement of colored products or leaching out the dye and leading to color heterogeneity in the detection zones. Furthermore, a waste layer was added to μPAD for loading of more amounts of the analyte, which results in improvement of detection limit. As a proof of concept, the μPAD was used for the analysis of Cu2+ ion. For this purpose, pyrocatechol violet and chrome azurol S as colorimetric reagents were doped into PVC membrane and injected in the detection zone. The proposed μPAD was presented good linearity in the ranges of 5.0–1400.0 and 5.0–200.0 mg L−1, and the limits of detections of 1.7 and 1.9 mg L−1 in presence of chrome azurol S and pyrocatechol violet, respectively.

A sonication of graphite in polysaccharide (pullulan, chitosan and alginate) is one of the viable methods for the preparation of few-layer graphene. However, the effect of these adsorbed polysaccharides on the electrical performance of the produced graphene so far is not yet clear. In order to investigate the present effect of pullulan, chitosan and alginate on the electrical characteristic of resulted graphene, we have produced few-layer graphene using bath sonication of graphite in pullulan, chitosan and alginate medium for the application as electrical conductive ink in strain-sensitive. Data from the TEM reveals the appearance of folded few-layer graphene flakes after sonication for 150 min while the XPS data shows that the chitosan-based graphene possesses the highest carbon-oxygen ratio of 7.2 as compared to that of the pullulan and alginate-based graphene. By subjecting the produced graphene as the ink for paper-based strain sensor, we have discovered that the chitosan-graphene has the best resistivity value (1.66 × 10-3 Ω⋅cm) and demonstrate the highest sensitivity towards strain (GF: 18.6). This result interestingly implies the potential of the reported chitosan-based conductive ink as a strain-sensitive material for future food packaging.

The incompatibility of most organic solvents with acetylcholinesterase (AChE) inhibition assay normally limits pesticide extraction efficiency in sample pretreatment, which might cause false negatives in real world sample assessment. Herein, a novel method has been developed for an improved AChE inhibition assay via organic solvent extraction combined spontaneous in situ solvent evaporation on microfluidic paper-based analytical devices. Enzyme pre-immobilization procedure was spared and AChE was added to the system after sampling step until a complete in-situ solvent evaporation process was performed on chip. IC50 levels of the six investigated organophosphate and carbamate pesticides indicated a completely eliminated influence of solvents on AChE behavior with the new method. Most importantly, analytical performances were significantly improved in food sample measurements. Reduction in matrix effect was observed when acetonitrile was adopted for lettuce sample pretreatment instead of water. Studies on different pesticides suggested a remarkably decreased discrimination effect on recoveries from sample pretreatment with the new developed method. The recovery level for phoxim spiked head lettuce samples reached (107.5 ± 14.2) %, in comparison with that of (18.6 ± 1.4) % from water-based extraction. Spiked water and apple juice samples with carbaryl concentration of as low as 0.02 mg L−1 were also successfully recognized with the present method by visual detection. This is the first report on direct sampling of organic extracts for AChE inhibition assay on-chip and it might provide a new perspective for real world sample assessments involving bio-reagents.

Herein we report the first two distance-based microfluidic paper-based analytical devices (μPADs) using fluorescence to quantify aluminum. In addition to their read-by-eye quantification, the devices are simple to fabricate, require no sample pretreatment or preconcentration, and have a shelf life of >5 months. The first device is designed in a “chemometer” format where the length of a fluorescent band linearly responds to an Al(III) concentration. The second device uses a radial design where the fluorescent diameter also linearly responds to an Al(III) concentration. The chemometer device has a detection limit of 2.5 ppm (100 μM) and a linear range from 2 to 54 ppm Al(III) (100 μM–1 mM), R2 = 0.989). The radial device has a detection limit of 0.9 ppm (33 μM) and a linear range from 2 to 24 ppm Al(III) (100–900 μM, R2 = 0.968). The utility of the μPADs were successfully demonstrated by measuring Al(III) in two water effluent samples from the Gold King Mine near Silverton, CO.

Rising concern about the use of non-permitted colourants, in common food items such as dals and green vegetables sold in Indian markets, have led to a demand for low-cost point-of-use chemical analysis tools. Conventional food-analysis techniques involving tedious sample preparation protocols are not suited for in-field applications. Surface Enhanced Raman Spectroscopy (SERS) is an analytical technique that is well-suited for point-of-use chemical analysis with molecular level detection capability, which can also serve as a quality assurance tool for businesses. Effective and rapid signal collection from a large-area sample within a field-setting using disposable, low-cost SERS substrates is a key challenge in implementing such a solution. Herein, we demonstrate the use of inkjet-printed thin films comprising of robust nanostructured-silver as flexible, paper-based SERS (P-SERS) swabs for the direct detection of Metanil Yellow (MY) from toor dal (yellow split pigeon peas) samples and Malachite Green (MG) from green peas and green chillies. The macroscopic uniformity of these thin-films in combination with a portable Raman spectrometer equipped with orbital raster scanning (ORS™) technology for signal collection results in an unprecedented precision (RSD ∼ 1.6%) upon characterizing samples saturated with Rhodamine-6G (R6G), a standard Raman probe. As several food-cleansing products have appeared in the marketplace, the adulterant removal efficacy of some commercially available ‘washes’ as well as products such as ‘ozoniser’, which was determined by SERS characterization of swabs before and after use, is also reported.

Despite that microfluidic paper-based analytical devices (μPADs) provide effective analytical platforms for point-of-care diagnosis in resource-limited areas, it remains challenging to achieve simple and low-cost fabrication of μPADs. A novel method for fabrication of μPADs is developed in this study using a folded polydimethylsiloxane (PDMS)-coated paper mask with a specific pattern to form a sandwich structure with inserted chromatographic paper. PDMS penetrates the target paper from the front and the back sides, and then is cured in the target paper to form legible channels. This method for prototyping μPADs has many favorable merits including simple operation without the need of trained personnel, fast fabrication and low cost. We further investigated colorimetric detection of melamine in the μPADs, and it showed a remarkable measurement with a detection limit of 0.1 ppm in aqueous solutions and liquid milk discriminated by the naked eye, which meets the detection limit required by USA and China. The fabricating strategy developed in this study is very promising and attractive for the development of simple μPADs for point-of-care applications, including diagnostic testing, food safety control and environmental monitoring.

Cellulose-based paper is an alternative substitution for petroleum-based polymers for packaging applications, but its mechanical performance is poor when in contact with water. Herein, chitosan was applied on cellulose-based paper via a coating approach. The effects of chitosan coatings between none and five layers on the color properties, wettability, thermal properties, mechanical performance, and overall migration in food simulants of the paper were evaluated. After the application of chitosan, chitosan first filled cavities between cellulose fibers within a network, and the chitosan film was formed on the paper surface later. This resulted in a pronounced increase in wettability and mechanical properties associated with a loss of whiteness and an increase in yellowness of the coated paper. The chitosan-coated paper became hydrophobic with a water contact angle of 94.7 ± 2.8°, and a robust improvement of 156.4% for tensile strength and 114.8% for strain at break was observed for the paper coated with three layers of chitosan in wet conditions in comparison to the uncoated paper. A reduction in the migration of the low molecular residuals from the paper could be hindered by the chitosan coating. These enhanced features revealed that chitosan-coated paper could be used as a food-contact material.

The adulteration of herbal medicines by dexamethasone or prednisolone is regarded as a serious problem in many communities. Herein, a novel platform for the separation and quantification of both target steroids in herbal medicines based on electrochemical paper-based analytical devices (ePADs) has been created. The ePAD was composed of Whatman SG81 chromatography paper, 3D-printed devices and a commercial screen-printed electrode. Whatman SG81 silica-coated paper was used for the separation of dexamethasone and prednisolone based on the difference in their partition coefficients during the flow of the mobile phase. The optimal mobile phase was composed of 60% ethyl acetate in cyclohexane and required 7 min for separation. The separated steroids on the paper were then quantified by electrochemical detection using differential pulse voltammetry, in which the 3D-printed devices facilitated the measurement. Analytical detection ranges of 10–500 μg mL−1 were obtained for both dexamethasone and prednisolone (r2 = 0.988 and 0.994, respectively). The limits of detection for dexamethasone and prednisolone were 3.59 and 11.98 μg mL−1, respectively, whereas the limits of quantification were 6.00 and 20.02 μg mL−1, respectively. The amounts of both target steroids derived from real herbal medicine samples determined by the proposed method were comparable to those obtained with assays using standard high-performance liquid chromatography. In addition, a simple evaporation step can be used to increase the concentration of the samples before analysis. These ePADs are simple, low-cost, rapid, and very promising for on-site quantitative detection.

The present study delineates the preparation, characterization, and application of (3-Aminopropyl)triethoxysilane (APTES)/Caprine liver-derived extracellular matrix (CLECM) coated paper matrix for cell delivery. Here, we exploited positively charged surface of the paper matrix (as imparted by APTES derivatization) to improve the biological responses of the cells. Our results demonstrated that the functionalized paper matrixes favored the adhesion, growth, and proliferation of multiple cell types including normal, transformed, cancerous, and stem cells as compared to the pristine paper matrix. Upon implantation into the mice model, the developed paper matrix supported infiltration of the host cells and vasculature without showing any evidence of significant systemic toxicity. Moreover, the cells cultured on the paper matrix, when delivered to the CAM and mouse models, showed an enhanced vascular network around the substrate, thereby confirming its potential to deliver the cells in vivo. Together, the study confirms that the reported paper-based platform is easy to fabricate, cheap, portable and could efficiently be applied to cell delivery applications for either tissue repair or the development of humanized animal model.

The facile detection of phosphopeptides is important for clinical screening and phosphoproteomic research. This work develops an instrument-free, cost-effective, convenient paper-based method for quantitative analysis of phosphorylated peptides. With a novel portable device, Phos-PAD, this method can achieve selective enrichment and colorimetric detection of phosphopeptides within 15 min TiO2 nanoparticle-based chemisorption and tetrabromophenol blue-based colorimetric assay were integrated into the single paper-based analytical device. The color change can indicate the presence of phosphopeptides and the mean pixel intensity of the red channel can be used for phosphopeptide quantification. With capability of quantifying phosphopeptides in serum samples, this Phos-PAD assisted phosphopeptide assay may attract significant attention to clinical analysis of endogenous serum phosphopeptides.

This paper describes the development of two microfluidic paper-based analytical devices (μPADs), one well-based and the other based on a lateral flow assay (LFA) configuration, to detect glucose via a colorimetric assay using the solid metal-organic framework (MOF) Zr-PCN-222(Fe), to encapsulate glucose oxidase (GOx). The well-based platform consisted of laminate sheets and multiple layers of wax-printed chromatography paper. Solutions of KI and glucose placed into the well flowed through the device and reacted with the GOx@MOF species sandwiched between the paper layers realizing a yellow-brown color. The LFA platform consisted of chromatography paper between parafilm and polyvinyl acetate (PVA) layers. GOx@MOFs spotted on the paper subjected to solutions of KI and glucose yielded a brown color. The devices were then dried, scanned, and analyzed yielding a correlation between average inverse yellow intensity and glucose concentrations. The development of these devices employing MOFs as biomimetic catalysts should further expand the applications of microfluidic technologies for sensors a variety of analytes.

This work demonstrates a sensitive and rapid method for the detection of antibiotic residues in food samples by employing the filtration behaviour of paper combined with aggregation and precipitation of chemical reagents. Using this concept, we successfully determined the presence of oxytetracycline and norfloxacin residues in pork using metal complexation on microfluidic paper-based analytical devices (μPADs). The base substrate (top layer of the device) was fabricated by printing letter channels of the words “oxytetracycline” and “norfloxacin” before functionalization with copper (II) sulfate pentahydrate in 0.5 M sodium hydroxide and iron (III) nitrate nanohydrate in 5 mM ammonia solution for the detection of oxytetracycline and norfloxacin separately. A transition metal hydroxide formed upon reaction that created solid precipitates on paper and allowed antibiotic residues to bind to the metal ions via coordination chemistry. The metal ion-antibiotic complex could form on the filter paper and generated a visible color change with the detection limit of 1 ppm for both oxytetracycline and norfloxacin in pork. This procedure of filtration and concentration in combination with a simple text-reporting approach allows the end users to achieve a low limit of detection as well as easy result interpretation in food safety monitoring. usc Refereed/Peer-reviewed

Cellulose is an interesting biopolymer offering numerous functionalization possibilities for various applications. Yet, cellulose functionalization usually involves expensive chemicals and complex processes. Here, we aim to utilize inexpensive fertilizer-grade phosphate for cellulose functionalization. Cellulose microfibers (CMF) were isolated from Giant Reed (GR) and were then phosphorylated using either a reagent-grade or a fertilizer-grade diammonium hydrogen phosphate (DAP) in the presence of urea following a water-based protocol. The effect of DAP on the phosphorylation reaction was mainly studied by conductometric titration, ICP-OES and FTIR, while further characterization was performed by SEM/EDX, TGA and XRD to investigate the morphology, composition, charge content, structure, and thermal degradation of the phosphorylated materials. It was found that cellulose phosphorylation using DAP fertilizer gave materials with the same charge content as that registered when using the reagent-grade DAP. Optimizing the reaction conditions with respect to the amount of fertilizer-grade DAP used for the phosphorylation gave high charge content (7000 mmol·g

Solar-reflective thermal insulating coating (SRC) has received great attention because of its desired heat reflective properties and water repellency, which may impart high-value to cellulosic paper via industrially well-established surface coating process. However, the feasibility and possibility of surface application of SRC to cellulosic paper have not been explored. Herein, in the present work, SRC was designed/developed and subsequently used in the surface application to cellulosic paper. Effect of feeding level of titanium dioxide nanoparticles (nano-TiO2) on rheological behavior of the coating, as well as heat-reflective properties, water repellency and mechanical properties of the surface-coated paper was studied. Results showed that the as-obtained coating samples exhibited a notable shear-thinning behavior and displayed strong dependence of rheological behavior on nano-TiO2 amount. Furthermore, the increased nano-TiO2 amount appeared to induce the improved hemispherical emittance of coated paper. The coating weight was also found to exert a positive effect on the hemispherical emittance of coated paper. In addition, it was confirmed that the nano-TiO2 addition played an important role in improving the water repellency and mechanical properties of coated paper.

This study describes the development of paper-based devices for the determination of biothiols. The devices are inexpensive (composed of paper and silver halide particles), and the analytical protocol is easily executable with minimum technical expertise and without the need of specialized equipment; the user has to add a test sample, illuminate the device with a UV lamp, and read the color change of the sensing area using a simple imaging device (i.e., cell-phone camera) or a bare eye. The detection mechanism of the assay is based on the biothiols-mediated photoreduction of nanometer-sized silver chloride particles deposited on the surface of paper; photoreduced silver chloride particles have a grayish coloration that depends on the concentration of biothiols in the tested solution. This is the first time that the UV-mediated photoreduction of solid silver halides particles is used for analytical purposes. The performance of the devices has been tested on the detection of total biothiols content of artificial body fluids and protein–free human blood plasma samples, and the results were satisfactory in terms of sensitivity, selectivity, recoveries and reproducibility.

The rapid and efficient treatment of complex wastewater remains challenging. Herein, green paper-based materials with high wet strength, good oil-water separation property and high heavy metal ion adsorption capacity were prepared via a facile, cost-effective process. The introduction of amphoteric functional groups not only met the requirements for heavy metal ion adsorption, but also maintained the stable underwater superoleophobic properties of materials a wide pH range. The covalent crosslinking between cellulose fibers induced by polyethyleneimine and citric acid significantly improved the wet strength (up to 26.0 Nm/g) and the porosity. The membrane flux was increased up to 3515 L/(m

Herein, we propose a highly sensitive and selective three-dimensional electrochemical paper-based analytical device (3D-ePAD) to determine serotonin (Ser). It uses a graphite-paste electrode modified with nanoparticles coated with molecularly imprinted polymer (MIP). Fe3O4@Au nanoparticles were encapsulated with silica to create novel nano-sized MIP. Morphology and structural characterization reveal that silica imprinted sites (Fe3O4@Au@SiO2) synthesized via sol-gel methods provide excellent features for Ser detection, including high porosity, and greatly improve analyte diffusion and adsorption to provide a faster response by the MIP sensor. The template molecule was effectively removed by solvent extraction to provide a greater number of specific cavities that enhance analyte capacity and sensitivity. The 3D-ePAD was fabricated by alkyl ketene dimer (AKD)-inkjet printing of a circular hydrophobic detection zone on filter paper for application of aqueous samples, coupled with screen-printed electrodes on the paper, which was folded underneath the hydrophobic zone. The sensor was constructed by drop coating of Fe3O4@Au@SiO2-MIP nanocomposites on the graphite electrode (GPE) surface. The MIP sensor (Fe3O4@Au@SiO2-MIP/GPE) was used in the detection of Ser by linear-sweep voltammetry (LSV) in 0.1 M phosphate buffer at pH 8.0. The device exhibits high sensitivity toward Ser, which we attribute to synergistic effects between catalytic properties, electrical conductivity of Fe3O4@Au@SiO2, and significantly increased numbers of imprinted sites. Ser oxidation was observed at +0.39 V. Anodic peak currents for Ser show linearity from 0.01 to 1000 μM (y = 0.0075 ± 0.0049 x + 0.4071 ± 0.0052, r2 = 0.993), with a detection limit of 0.002 μM (3S/N). The device provides good repeatability (%relative standard deviations; RSD) = 4.23%, calculated from the current responses of ten different MIP sensors). The device also exhibits high selectivity and reproducibility (%RSD = 8.35%, obtained from five calibration plots). The analytical performance of the device is suitable for the determination of Ser in pharmaceutical capsules and urine samples.

In situ identification and quantification of unsaturated fatty acid (FA) C=C positional isomers in human serum is herein performed by negative-ion paper spray (PS) mass spectrometry. Typically, by direct application of an alternating current (AC) voltage to the wet paper, the PS ionization could perform stably in the negative-ion mode without severe discharge. We suppose epoxidation reaction between unsaturated C=C bonds and reactive oxidative species might be initiated by a mild electrical discharge, which could be rapidly and controllably produced via a low amplitude AC voltage. Upon collision-induce dissociation (CID), the epoxide was fragmented to generate diagnostic ions indicating the C=C location. The intensity of the characteristic product ions could also be used for absolute quantification of the FA C=C positional isomers. The limits of detection (LODs) and limits of quantification (LOQs) were roughly in the range of 0.0178–0.0506 μM and 0.0218–0.3634 μM for standard FAs. Without the additional sample preparations or reactive chemical reagents, epoxidation of unsaturated FAs and ionization of the epoxide could be achieved in one-step by negative-ion mode PS, which enable a promising methodology for on-site clinical diagnosis.

Fluoro-functionalized paper was prepared and applied in solid phase extraction (SPE) for the analysis of trace-level perfluorinated compounds (PFCs). The proposed fluoro-functionalized paper-based solid-phase extraction (Fp-SPE) exhibits significant advantages for sample preparation, such as the biodegradability of paper-based adsorbent, simple manipulation and low cost. Owing to the fluorous affinity, the Fp-SPE technique with high sensitivity and high selectivity is more suitable for the selective enrichment of fluorine-containing molecules from the background of non-fluorinated organic compounds in a real water sample. Combined with high-performance liquid chromatography coupled with electrospray ionization-tandem mass spectrometry analysis (HPLC-MS/MS), the linear range of the PFCs, including perfluorobutyric acid (PFBA), perfluorooctanic acid (PFOA), perfluorooctane sulfonic acid (PFOS), and perfluorodecanoic acid (PFDA), was 0.20–5.0 ng/L with the limits of detection (LOD) ranging from 0.04–0.05 ng/L and the limits of quantification (LOQ) ranging from 0.15-0.20 ng/L. The method was then applied to the analysis of tap water, river water and waste water samples. The results of the actual sample analysis are consistent with that by reverse phase SPE (RP-SPE).

In most cases, three-dimensional paper-based microfluidic analytical devices (3D-μPADs) were fabricated manually by stacking or folding methods. For the first time, digital light processing stereolithography (DLP-SLA) 3D printing technology was adopted to automatically make 3D-μPADs. In the fabrication process, a printing pause was set between two layers to allow paper to be placed in the resin tank. The resin on the fresh paper spontaneously bonded to the former cured paper layer during curing, thus realizing the automatic bonding and alignment between different layers of paper and avoiding the human participation and errors as in stacking and folding methods. There was a gap between two vertical aligned flow paths, therefore the liquid did not flow spontaneously from the upper layer to the lower layer. Most of the fluid flow in 3D-μPADs was spontaneous or manually activated, which was not conducive to complex assays that require different regents to be delivered sequentially. Herein, we used an electric field or airflow to trigger the fluid flow and demonstrated the flow controllability by a proof-of-concept colorimetric assay. The limits of detection of glucose and albumin were 0.8 mM and 3.5 μM, respectively, which were sufficient for clinical requirements. Given the characteristic of flow controllability, we believe that the proposed 3D-μPADs have great potential to make paper-based complex assays automated and programmable.