Search

Nuisance caused by odors is one of the most important problems for waste management plants. To control an odor nuisance, it must first be quantified. The analytical difficulties in odor measurements are related to the high number of volatile components (belonging to several chemical classes), above all when the concentration is lower than the detection limit of the technique used for the measurement. In this work, 2-butanone, α-pinene, tetrachloroethylene, dimethyldisulfide, β-pinene, limonene, phenol and benzoic acid are determined, because they are representative of some important classes of compounds with higher odor impact. The compounds are sampled with thermal desorbable radial diffusive samplers Radiello® containing Tenax cartridges. The analytical repeatability and the complete thermal desorption of the cartridges were verified for each odor compound; the relative standard deviations for repeated samples and the recovery percentage were, respectively, less than 7% and about 97% for all compounds. The measurements of the linearity of sampling showed no systematic difference according to the collection period. The comparison between the odor threshold and the limit of detection demonstrated that this method is reliable for the recognition and quantification of odor compounds, allowing Public Administration to impose legal limits and the control agencies to verify them. [Copyright &y& Elsevier]

This study provided a useful approach for assessing the impact of industrial sources on surrounding, especially in a sensitive industrial area as Taranto (South of Italy). Taranto is one of the most industrialized Italian towns, where several emission sources operate simultaneously in proximity to the urban settlement. An intensive monitoring campaign of PAHs was carried out from January 28th to July 30th, 2011, in seven sites located in residential settlement around the industrial area and in the city center. The collected data were integrated with the information about wind direction and speed by means bivariate polarplot in order to characterize and localize the industrial sources. High BaP concentrations were detected especially when Benzene to Toluene ratio (B/T ratio) values excedeed 1 and all receptor sites were downwind to the steel plant. Moreover, in order to discriminate among PAH sources and quantify their contributions, a source apportionment analysis of the collected data was provided by means Principal component Analysis (PCA) and Positive Matrix Factorization (PMF) methods. Finally, the processing of PMF5.0 output by bivariate polar plot, confirmed the impact of steel plant on both industrial sites downwind the steel plant and the city center. B[a]P apportionment was quite similar for industrial and urban sites: the traffic source contributed only 11% and 24% to B[a]P measured at two sites, respectively. Therefore, the proximity of Taranto downtown to industrial pole makes negligible all other source contributions to PAH concentrations. [ABSTRACT FROM AUTHOR]

Abstract: An assessment of the fugitive emission impact on ambient air PM, PAHs and metal concentrations was performed in a residential area near the biggest European steel plant. A careful experimental design was developed to characterize fugitive emissions produced by the integrated steel plant. A PM10 and PM2.5 monitoring campaign was conducted at three sampling sites around the steel plant, in order to perform a triangulation in the area surrounding the investigated site and evaluate its impact based on wind direction. Data analysis showed that the transport of air mass, from the steelworks to one of the receptor sites, resulted in ambient air concentrations of Fe, Mn, Zn and PAHs higher than those observed in the other two sites. Principal component analysis allowed the identification of four emission sources: coke ovens stack, mineral park, a crustal source and vanadium source. The first two sources were characterized by high concentrations of PAHs and metals and related to the steelworks, while the vanadium source was probably associated with maritime traffic in the port area. This preliminary monitoring approach proved effective in identifying the fugitive emission contribution of the steel plant to the surrounding air quality. [Copyright &y& Elsevier]

Abstract: Radiello®, a radial symmetry diffusive sampler, has been evaluated for its potential for ambient air quality monitoring, in particular for benzene, toluene, ethyl benzene, p-xylene, m-xylene, o-xylene (BTEX) measurements. BTEX were first sampled onto adsorbing cartridges before analyses were performed by thermal desorption and GC-MS. Tests were carried out to determine blank values and any storage effects. The results of an investigation into repeatability of the Radiello® sampler and the influence of sampling time under field conditions are reported. Inter-comparison with automatic instruments is also illustrated. [Copyright &y& Elsevier]