Search

The stress relaxation of the TZ region, located at the interface of the Annulus Fibrosus (AF) and Nucleus Pulposus (NP) of the disc, and how its stress is relaxed compared to the adjacent regions is unknown. The current study aimed to identify the TZ stress relaxation properties under different strain magnitudes (0.2, 0.4, and 0.6 mm/mm) and compared the TZ stress relaxation characteristics to the NP and inner AF (IAF) regions at a specific strain magnitude (0.6 mm/mm). The results of the current study revealed that the TZ region exhibited different stress relaxation properties under various strain magnitudes with significantly higher initial (p < 0.008) and reduced stresses (marginally; p = 0.06) at higher strains. Our experimental stress relaxation data revealed a significantly higher equilibrium stress for the IAF compared to the TZ and NP regions (p < 0.001) but not between the TZ and NP regions (p = 0.7). We found that NP radial stress relaxed significantly faster (p < 0.04) than the TZ and NP. Additionally, the current study proposed a simple mathematical model and identified that, consistent with experimental data, the overall effect of region on both the level of decayed stress and the rate at which stress is relaxed was significant (p < 0.006). The current study found a similar stress relaxation characteristic between the NP and TZ regions, while IAF exhibited different stress relaxation properties. It is possible that this mismatch in stress relaxation acts as a shape transformation mechanism triggered by viscoelastic behavior. Our understanding of the biomechanical properties of the transition zone (TZ) in the IVD, a region at the interface of the Nucleus Pulposus (NP) and Annulus Fibrosus (AF), is sparse. Unfortunately, there are no current studies that investigate the TZ stress relaxation properties and how stress is relaxed in the TZ compared to the adjacent regions. For the first time, the current study characterized the stress relaxation properties of the TZ and described how the TZ stress is relaxed compared to its adjacent regions. [Display omitted] [ABSTRACT FROM AUTHOR]

The meniscus tissue is crucial for knee joint biomechanics and is frequently susceptible to injuries resulting in early-onset osteoarthritis. Consequently, the need for meniscal substitutes spurs ongoing development. The meniscus is a composite tissue reinforced with circumferential and radial collagenous fibers; the mechanical role of the latter has yet to be fully unveiled. Here, we investigated the role of radial fibers using a synergistic methodology combining meniscal tissue structure imaging, a computational knee joint model, and the fabrication of simple biomimetic composite laminates. These laminates mimic the basic structural units of the meniscus, utilizing longitudinal and transverse fibers equivalent to the circumferential and radial fibers in meniscal tissue. In the computational model, the absence of radial fibers resulted in stress concentration within the meniscus matrix and up to 800 % greater area at the same stress level. Furthermore, the contact pressure on the tibial cartilage increased drastically, affecting up to 322 % larger areas. Conversely, in models with radial fibers, we observed up to 25 % lower peak contact pressures and width changes of less than 0.1 %. Correspondingly, biomimetic composite laminates containing transverse fibers exhibited minor transverse deformations and smaller Poisson's ratios. They demonstrated structural shielding ability, maintaining their mechanical performance with the reduced amount of fibers in the loading direction, similar to the ability of the torn meniscus to carry and transfer loads to some extent. These results indicate that radial fibers are essential to distribute contact pressure and tensile stresses and prevent excessive deformations, suggesting the importance of incorporating them in novel designs of meniscal substitutes. The organization of the collagen fibers in the meniscus tissue is crucial to its biomechanical function. Radially oriented fibers are an important structural element of the meniscus and greatly affect its mechanical behavior. However, despite their importance to the meniscus mechanical function, radially oriented fibers receive minor attention in meniscal substitute designs. Here, we used a synergistic methodology that combines imaging of the meniscal tissue structure, a structural computational model of the knee joint, and the fabrication of simplistic biomimetic composite laminates that mimic the basic structural units of the meniscus. Our findings highlight the importance of the radially oriented fibers, their mechanical role in the meniscus tissue, and their importance as a crucial element in engineering novel meniscal substitutes. [Display omitted] [ABSTRACT FROM AUTHOR]

Understanding the structure-function relationship in the intervertebral disk (IVD) is crucial for the development of novel tissue engineering strategies to regenerate IVD and the establishment of accurate computational models for low back pain research. A large number of studies have improved our knowledge of the mechanical and structural properties of the nucleus pulposus (NP) and annulus fibrosus (AF), two of the main regions in the IVD. However, few studies have focused on the AF-NP interface (transition zone; TZ). Therefore, the current study aims to, for the first time, characterize the cyclic and failure mechanical properties of the TZ region under physiological loading (1, 3, and 5% s −1 strain rates) and investigate the structural integration mechanisms between the NP, TZ, and AF regions. The results of the current study reveal significant effects of region (NP, TZ, and AF) and strain rates (1, 3, and 5% s −1) on stiffness (p < 0.001). In addition, energy absorption is significantly higher for the AF compared to the TZ and NP (p <0.001) as well as between the TZ and NP (p <0.001). The current research finds adaptation, direct penetration, and entanglement between TZ and AF fibers as three common mechanisms for structural integration between the TZ and AF regions. Despite a large number of studies that have mechanically, structurally, and biologically characterized the nucleus pulposus (NP) and annulus fibrosus (AF) regions, few studies have focused on the NP-AF interface region (known as Transition Zone; TZ) in the IVD; hence, our understanding of the TZ structure-function relationship is still incomplete. Of particular importance, the cyclic mechanical properties of the TZ, compared to the adjacent regions (NP and AF), are yet to be explored and the precise nature of the structural integration between the NP and AF via the TZ region is not yet known. The current study explores both the mechanical and structural properties of the TZ region to ultimately identify the mechanism of integration between the NP and AF. [Display omitted] [ABSTRACT FROM AUTHOR]

The aging western society is heavily afflicted with intervertebral disc (IVD) degeneration. Replacement or repair of the degenerated IVD with an artificial bio-mimetic construct is one of the challenges of future research due to its complex structure and unique biomechanical function. Herein, biocomposite laminates made of long collagen fibers in unidirectional (−1.3 ± 2.1°) and angle-plied ± 30° orientations (30.4 ± 6.4 and −29.8 ± 4.5), embedded in alginate hydrogel, were fabricated to mimic the form of single annulus fibrosus (AF) lamella and the circumferential AF, respectively. The mechanical behavior of the composites was measured and compared with in vitro existing data of the human native AF as well as with new data obtained from ovine and bovine specimens. The mechanical behavior was found to reproduce the full stress- strain behavior of the human AF single lamella in several regions of the AF and the Young's modulus was 28.3 ± 8.6 MPa. Moreover, the modulus of the angle-plied laminates was 16.8 ± 2.9 MPa, which is approximately 5% less than the in vitro data. The full stress-strain behavior was also compared with bovine and ovine circumferential AF samples and found to be very similar, with a difference in the modulus of 4.1% and 19.7%, respectively. Moreover, an FE model of the L3-L4 functional spinal unit (FSU) was developed and calibrated to evaluate the mechanical ability of the biocomposite to be used as an AF substitute under physiological IVD loading modes. The biocomposite demonstrated a good ability to mimic the stiffness of the native tissue under physiologic loading modes as flexion, extension, lateral bending and compression, but was too flexible under torsion. It was found that the proposed biomimetics AF design resulted in a compatible function in several mechanical levels, which holds great potential to be used as a viable AF replacement towards full IVD engineering. [ABSTRACT FROM AUTHOR]

Background: The intervertebral disc (IVD) is a complex organ that acts as a flexible coupling between two adjacent vertebral bodies and must therefore accommodate compression, bending, and torsion. It consists of three main components, which are elegantly structured to allow this: the annulus fibrosus (AF), the nucleus pulposus (NP), and the end-plates (EP).Purpose: Thus far, it has not been possible to examine the microarchitecture of the disc directly in three dimensions in its unaltered state and thus knowledge of the overall architecture of the disc has been inferred from a range of imaging sources, or by using destructive methods.Study Design: A nondestructive ultrahigh field Magnetic Resonance Imaging (MRI) of 11.7 T was used together with image analysis to visualize the ovine IVDs.Methods: Three-dimensional image stacks from eight IVDs harvested from sheep, half of which were 4 to 5 years old and the others approximately 2 years old were reconstructed and examined, and their microstructure were imaged. The overall structure of the disc, including the average of 14 AF lamellae (9-28), NP, and EP was then visualized with particular attention given to integrating elements as radial translamellar cross-links, AF-NP transition zone EP-AF integration and EP-NP insertion nodes (ie the connecting junctions between the EP and NP). Moreover, collagen fiber orientation was determined at different depths and locations throughout the annulus.Results: It was found that there was a clearer demarcation in the AF-NP transition zone of the younger discs compared with the older ones. This difference was reflected in the visibility of AF-NP and EP-AF integration. It was also possible to view the fiber architecture of the AF-NP integration in greater depth than was possible previously with histological techniques. These fibers were mainly observed in the younger discs and their length was measured to be of 2.6 ± 0.2 mm.Conclusions: The present results provide a substantial advance in visualization of the three-dimensional architecture of an intact IVD and the integration of its components. [ABSTRACT FROM AUTHOR]

Soft tissues are constructed as fiber-reinforced composites consisting of structural mechanisms and unique mechanical behavior. Biomimetics of their mechanical behavior is currently a significant bioengineering challenge, emphasizing the need to replicate structural and mechanical mechanisms into novel biocomposite designs. Here we present a novel silk-based biocomposite laminate constructed from long natural silk and fibroin fibers embedded in an alginate hydrogel matrix. Controlling the mechanical features of these laminates were studied for different fiber volume fractions (VF) and orientations using unidirectional tensile tests. Three material systems were investigated having different fiber orientations: longitudinal (0°), transverse (90°), and cross-plied (0/90°). The general behavior of the biocomposite laminates was anisotropic hyperelastic with large deformations. Longitudinal fibroin laminates have shown a tensile modulus of 178.55 ± 14.46 MPa and tensile strength of 18.47 ± 2.01 MPa for 0.48 VF. With similar VF, cross-plied fibroin laminates demonstrated structural shielding ability, having a tensile modulus and tensile strength of 101.73 ± 8.04 MPa and 8.29 ± 1.63 MPa for only a third of the VF directed in the stretching direction. The stress-strain behavior was in a similar range to highly stiff native human soft tissues such as ligament and meniscus. These findings demonstrate the potential of the fibroin fiber-reinforced biocomposites to mimic the mechanics of tissues with a quantitatively controlled amount of fibers and designed spatial arrangement. This can lead to new solutions for the repair and replacement of damaged functional and highly stiff soft tissues. [ABSTRACT FROM AUTHOR]

Soft tissue can be viewed as a multi-layered composite structure reinforced with different collagen fiber systems used to control the overall mechanical properties. The objective of this study was to manufacture, test and model the mechanical behavior of a multidirectional collagen reinforced composite material system. To that end, novel bio-composite constructs were fabricated from long collagen fibers reinforced polyacrylamide–alginate (PAAm–Alg) matrix. The collagen fibers were aligned in multi-directions within thin circular matrix plates. The constructs were clamped and subjected to flexure using a rigid spherical indenter. Three dimensional finite element (FE) models were generated with continuum and beam elements representing the matrix and fibers, respectively. The hyperelastic behavior predicted by the calibrated FE models was validated based on the results of one tested configuration. The new bio-inspired composites can be tailored to generate similar mechanical behavior of native tissues. The FE model can be employed to design future complex constructs for soft tissue substitutes. [ABSTRACT FROM AUTHOR]

The objective of this study was to introduce a class of collagen-fiber reinforced bio-composite laminates as biomimetic of soft tissues. These novel all-natural bio-composite laminates include long collagen fibers from soft coral embedded in an alginate hydrogel matrix. Controlling the fiber orientation and volume fraction enabled the fabrication of laminates with wide range of mechanical behaviors. Four material systems were investigated in the current study having different fiber orientations: longitudinal (0°), transverse (90°), cross-plied (0/90°) and angle-plied (±30°). The range of Fiber volume fractions (FVFs) for the laminated membranes is between 0.21 and 0.31. The laminates were subjected to uniaxial loading, yielding hyperelastic stress–strain behavior. A hyperelastic finite element (FE) model was constructed for the heterogeneous laminate, based on the fiber and matrix hyperelastic material behavior and their FVF, in order to predict the overall bio-composite mechanical behavior. The predictions of the FE model were verified from the tested laminated systems. The FE model consisted of beam elements representing the collagen fibers embedded in the solid matrix (alginate). Good predictions were demonstrated by the proposed FE model compared with the tested bio-composites for all orientations up to 10% strain. The overall hyperelastic stress–strain behavior was in a similar range to known native soft tissues. In addition, the model allowed for examining the mechanical behavior of laminates with other FVFs. The new bio-composite material can be used for future soft tissue mimicry and repair. [ABSTRACT FROM AUTHOR]

A novel collagen-based bio-composite was constructed from micro-crimped long collagen fiber bundles extracted from a soft coral embedded in alginate hydrogel matrix. The mechanical features of this bio-composite were studied for different fiber fractions and in longitudinal and transverse loading modes. The tensile modulus of the alginate hydrogel was 0.60±0.35MPa and in longitudinal collagen-reinforced construct it increased up to 9.71±2.80 for 50% fiber fraction. Ultimate tensile strength was elevated from 0.08±0.04MPa in matrix up to 1.21±0.29 for fiber fraction of 30%. The bio-composite demonstrated hyperelastic behavior similar to human native tissues. Additionally, a dedicated constitutive material model was developed to enable the prediction of the longitudinal mechanical behavior of the bio-composite. These findings will allow tailor-designed mechanical properties with a quantitatively controlled amount of fibers and their designed spatial arrangement. This unique bio-composite has the potential to be used for a wide range of engineered soft tissues. [ABSTRACT FROM AUTHOR]

Cardiovascular Diseases (CVDs) are the leading cause of death worldwide. Approximately 31% of all global deaths are caused by CVDs, of which 42% are attributable to coronary artery disease (CAD). CAD is characterized by a narrowing of arteries that restricts the normal blood flow. Over time, surgical intervention is required in severe cases of occlusions and includes implantation of autologous vessels. Today synthetic grafts are used successfully as replacements for blood vessels with a diameter larger than 6 mm. However, they often fail as small-diameter blood vessel replacements. This study introduces a new biocomposite material system consisting of unique and long (cm-scale) collagen fibers derived from soft corals embedded within an alginate hydrogel matrix. The new biocomposite layers were used to fabricate grafts, towards developing a new class of tissue-engineered small-diameter blood vessels. These constructs consisted of both circumferentially and longitudinally oriented collagen fibers. The mechanical properties of the grafts were investigated via a new experimental setup constructed in our lab for this purpose, which applied internal pressure levels of 0–300 mmHg. Similar to native coronary arteries, the biocomposite tubes demonstrated a compliance of 4.88 ± 0.99%/100 mmHg for a physiologic pressure range of 80–120 mmHg. Furthermore, a numerical finite element simulation model is proposed to generate the overall mechanical response of the construct. It is composed of axial and circumferential fibers embedded within the continuum alginate elements. Good prediction is demonstrated when compared with the measured pressure-strain response. Moreover, we examined biocompatibility and cell growth on the collagen fibers. Fibroblast cells proliferated during the experiment that lasted for 32 days and showed aligned configuration with the collagen fiber orientation. The novelty of this study is manifested in the use of naturally derived coral-based long collagen fibers for the development of a new class of tissue-engineered grafts. The proposed novel biocomposite graft demonstrated both mechanical and biological compatibility and can be further developed for small-diameter blood-vessel replacement. [Display omitted] • Coral collagen fibers are used to reinforce a cylindrical biocomposite. • The proposed graft exhibited a similar compliance to that of human coronary arteries. • Finite element model predicted pressure-strain behavior close to the measured responses. • The collagen fibers demonstrated good biocompatibility in vitro. • Cell alignment was dictated by the fiber orientation. [ABSTRACT FROM AUTHOR]