Search

Abstract: Optical fibers are key components in telecommunication technologies. Apart from optical specifications, optical fibers are expected to keep most of their physical properties for 10–20 years in current operating conditions. The reliability and the expected lifetime of optical links are closely related to action of the chemical environment on the silica network. However, the coating also contributes largely to the mechanical properties of the fibers. The aim of this work was to study the strength and the mechanical behavior of the silica optical fibers in an acid environment and with a permanent deformation. A container with ammonium bifluoride acid salt was plunged into hot water at different temperatures (55 and 75°C). This emitted acid vapors which attacked the optical fibers for a period of 1–18 days. An aging study was performed on silica optical fibers with standard polyacrylate coating and with hermetic carbon coating. A dynamic two-point bending bench at different faceplate velocities (100, 200, 400 and 800μm/s) was used. For comparison, the same dynamic measurements were also carried out on non-aged fibers. After acid vapor condensation, salt crystal deposits on the fibers were displayed using an electron scanning microscope. These crystals became visible to the naked eye from the seventh day. [Copyright &y& Elsevier]

The safety of microwave and electron-beam treatments has been demonstrated, in regards to the formation of reaction products that could endanger human health. An integrated approach was used combining the potential toxicity of all the substances likely to migrate to their chemical characterizations. This approach was applied to polypropylene (PP) films prepared with a selection of additives. Components were identified by liquid and gas chromatography using a mass selective detector system. Their potential toxicity was assessed using three in vitro short-term bioassays and their migrations were carried out using a standards-based approach. After the electron-beam treatment some additives decomposed and there was a significant increase in the polyolefin oligomeric saturated hydrocarbons concentration. PP prepared with Irgafos 168 led to a significantly strong cytotoxic effect and PP prepared with Irganox 1076 induced a dose-dependant estrogenic effect in vitro . Migration values were low and below the detection limit of the analytical method applied. [ABSTRACT FROM AUTHOR]

Abstract: Nineteen food contact papers and boards and one non-food contact board were extracted following test protocols developed within European Union funded project BIOSAFEPAPER. The extraction media were either hot or cold water, 95% ethanol or Tenax, according to the end use of the sample. The extractable dry matter content of the samples varied from 1200 to 11,800mg/kg (0.8–35.5mg/dm2). According to GC–MS the main substances extracted into water were pulp-derived natural products such as fatty acids, resin acids, natural wood sterols and alkanols. Substances extracted into ethanol particularly, were diisopropylnaphthalenes, alkanes and phthalic acid esters. The non-food contact board showed the greatest number and highest concentrations of GC–MS detectable compounds. The extracts were subjected to a battery of in vitro toxicity tests measuring both acute and sublethal cytotoxicity and genotoxic effects. None of the water or Tenax extracts was positive in cytotoxicity or genotoxicity assays. The ethanol extract of the non-food contact board gave a positive response in the genotoxicity assays, and all four ethanol extracts gave positive response(s) in the cytotoxicity assays to some extent. These responses could not be pinpointed to any specific compound, although there appeared a correlation between the total amount of extractables and toxicity. [Copyright &y& Elsevier]

Abstract: The reliability and the expected lifetime of optical fibers used in telecommunication technologies are closely related to the chemical environment action on the silica network. To ensure the long-term mechanical strength of the optical fibers, a polymer coating was applied onto the fiber surface during fiber fabrication. This external coating is vital to ensure a long optical fiber lifetime. Its protective action includes several functions, such as to protect glass fiber from any external damage, to limit chemical attack, in particular that of water, and finally to ensure fatigue protection and bending insensitivity, especially during handling and in-service installation. Since the mechanical strength of the fiber is controlled by its surface characteristics, we propose a new method for increasing fiber strength. The silica optical fibers used were 125μm in diameter, with a 62.5μm thick epoxy-acrylate coating. Fibers were rolled up around two similar cylinders. Using a screw, these cylinders moved away from one another and thus subjected the fibers to stretching. Submitted to this mechanical loading, the distended fibers were plunged into hot water at 65 or 85°C and aged for several days. Then, the fibers were removed from the water and various weights were suspended on the fiber ends. Thus, the fibers were subjected to a tensile loading in static fatigue for several days. Just before fiber rupture, the fibers were unloaded and subjected to dynamic tensile tests at different velocities. Result analysis proved that the aging in hot water increased the fiber strength. The Weibull''s diagram study shows a bimodal dispersion of defects on the fiber surface and the important role of polymer coating. [Copyright &y& Elsevier]