Search

The influence of wood components and cellulose crystallinity on the kinetic degradation of different wood species has been investigated using thermogravimetry. Four wood species were studied: Pinus elliottii (PIE), Eucalyptus grandis (EUG), Mezilaurus itauba (ITA) and Dipteryx odorata (DIP). Thermogravimetric results showed that higher extractive contents in the wood accelerate the degradation process and promote an increase in the conversion values at low temperatures. Alternatively, the results indicated that the cellulose crystallinity inhibits wood degradation; organized cellulose regions slow the degradation process because the well-packed cellulose chains impede heat diffusion, which improves the wood’s thermal stability. The wood degradation mechanism occurs by diffusion processes when the conversion values are below 0.4. When the conversion values are above 0.5, the degradation is a result of random nucleation with one nucleus in each particle. [ABSTRACT FROM AUTHOR]

Abstract: The purpose of this study is to investigate the torrefaction behavior of woody biomass (Lauan) blocks and its influence on the properties of the wood. Three different torrefaction temperatures of 220, 250 and 280 °C, corresponding to light, mild and severe torrefactions, and four torrefaction times of 0.5, 1, 1.5 and 2 h were considered. After analyzing the torrefied woods, it was found that the torrefaction temperature of 280 °C was able to increase the calorific value of the wood up to 40%. However, over 50% of weight was lost from the wood. The grindability of the torrefied wood could be improved in a significant way if the torrefaction temperature was as high as 250 °C and the torrefaction time longer than 1 h. Therefore, the torrefaction temperature of 250 °C along with the torrefaction time longer than 1 h was the recommended operation to intensify the heating value and grindability as well as to avoid too much mass loss of the wood. This study also suggested that over 50% of the reacted wood was converted into condensed liquid. The main components in the liquid were monoaromatics; little amount of heterocyclic hydrocarbons were also obtained from the torrefactions, especially at the torrefaction temperature of 280 °C. [Copyright &y& Elsevier]

Abstract: Experimental techniques such as the cone calorimeter, representing realistic fire conditions, and the thermogravimetric analyser (TGA) combined with evolved gas analysis (EGA) can be used to determine flammability and degradation properties of materials. The desire is to correlate the flammability properties measured in the cone calorimeter for samples of size 100mm×100mm with those measured or deduced from TGA combined with EGA for milligram samples. Such an achievement will allow the design of fire-safe materials by quickly assessing (a) the fire safety of materials in their earliest milligram formulation and (b) the dependence of their flammability properties on the molecular structure of the material. In the present study, a cone calorimeter and TGA investigation is conducted for commercial Nordic Spruce wood impregnated by mono-ammonium phosphate (fire retardant, FR) through a vacuum pressure method. Experiments in the cone calorimeter with increasing FR concentrations indicated that (a) the char yields increased, (b) the apparent ignition temperature increased, (c) time to piloted ignition increased, (d) the total amount of heat released was reduced, (e) the peak heat release rate was reduced and (f) the carbon monoxide and smoke yields increased especially before ignition occurred. By comparison, char yields also increased with FR content in the TGA degradation experiments in nitrogen. The increase in the char yield with FR content explains quantitatively the decrease in the heat release in the cone calorimeter. By contrast, the onset temperatures measured in TGA decreased, whereas the ignition temperature deduced in the cone calorimeter increased with FR content. This difference is attributed to reduced yield of levoglucosan (reported in recent literature using TGA/EGA) with increased char yield as well as to the presence of phosphorous containing moieties in the volatiles, which both can quench piloted ignition. Finally, the TGA measurements showed that the FR concentrations decreased for milligram samples at different distances from the surface of the wood used in the cone calorimeter measurements. The variation of FR retardant with depth needs to be considered when using TGA data to interpret cone calorimeter measurements and the fire performance of the FR wood in approval tests such as the single burning item (SBI). [Copyright &y& Elsevier]