Search

In order to study the effects of different parameters in hydraulic fracturing on formation temperature after low-temperature fracturing fluid is injected into high-temperature reservoir, in this paper, considering (1) osmotic pressure and capillary pressure (2) microthermal effect (heat conduction, heat convection, heat expansion, viscous dissipation) (3) the coupling processes of temperature (T), hydraulic, (H) mechanical (M) and chemical (C) in hydraulic fracturing process, and the coupled temperature prediction model of oil-water two-phase THMC based on discrete fractures is established. The effects of fracturing fluid temperature, reservoir temperature, dimensionless conductivity, Young's modulus, injection rate, cluster spacing, and proportion of branch fracture area on reservoir and fracture temperature during the pumping and shut-in stages of shale oil reservoir were studied. The results show (1) For formations with different reservoir temperatures, the temperature drop at the fracture was approximately 97% from the start of the operation to the end of the 30-day shut-in. The saturation change caused by fracturing fluid filtration is much larger than the temperature change caused by heat transfer, and it is found that the temperature and saturation change mainly occur in the early shut-in period (2) Imbibition accelerates the filtration loss of fracturing fluid. During pumping, the bottom hole temperature with imbibition considered is lower than that without imbibition considered. The temperature curve with imbibition considered begins to deviate about 10 min after pumping, but the final temperature tends to be the same, (3) When the fracturing fluid is pumped at high pressure, the fracture and matrix will be deformed, which will improve the porosity and permeability of the near well zone, thus speeding up the heat transfer rate. The high Young's modulus inhibits the increase of permeability. Compared with the young's modulus of 40 GPa and 20 GPa, the increase of permeability decreases by 9% (4) When the well was shut in for 30 days, the cluster spacing was greater than 20 m, and the temperature change around the fracture did not affect the clusters on both sides. The spacing between the clusters was 5 m, and the perforation clusters on both sides had a significant effect on the temperature. The temperature of the reservoir between the two adjacent clusters dropped from 393 K to 385 K. When there is a branch fracture, the small cluster spacing is equivalent to increasing the complexity of the fracture and accelerating the initial heat transfer rate. (5) High injection temperature, high dimensionless conductivity, low Young's modulus and low pumping rate are conducive to the heat transfer of fracturing fluid in the formation. • Based on the discrete fracture model, the temperature prediction model of oil-water two-phase flow was established. Considering the capillary force and osmotic pressure, the temperature (T) -hydraulic (H) -mechanical (M) -chemical (C) was realized. The finite element method is used to solve the model. • The effects of multiple factors on reservoir and fracture temperature during fracturing pumping and shut-in stages are analyzed. [ABSTRACT FROM AUTHOR]

• A new model is proposed to study the multi-cluster fracturing. • The influence of different factors on the fracture propagation is studied. • The accuracy of model is verified by experiment. Multi-cluster fracturing in horizontal wells is a key technology for successful development of ultra-low permeability reservoir. The propagation of hydraulic fracture during multi-cluster fracturing is complicated, especially in shale reservoir with multiple natural fractures. The design and operation of multi-cluster fracturing requires adequate understanding of influence of different factors on hydraulic fracture propagation. Up to now, many scholars have studied the hydraulic fracture morphology in multi-cluster fracturing, but few have analyzed the effect of natural fractures on hydraulic fracture propagation during multi-cluster fracturing. In this paper, a new computationally version of the particle-based model is established by Xsite to study the fracture propagation in multi-cluster fracturing with natural fractures. The tensile strength and rock toughness are calculated, and tri-axial experiments are performed to verify the accuracy of model. Simulation results show that cluster spacing and in-situ stress difference have a significant influence on the length of the hydraulic fracture and the morphology of fracture. The length of middle fracture increases with the increase of the cluster spacing, but decreases with the increase of the in-situ stress difference during multi-cluster fracturing with three natural fractures. The enhancing of cluster spacing can reduce the deflection of left and right fractures, and the increase of the in-situ stress difference can improve the ability of middle fracturing penetrating the natural fracture. Three fracturing sequence of synchronous fracturing, two-step fracturing and sequential fracturing is simulated. The left and right fractures can always penetrate the natural fracture with different fracturing sequence. But the middle fracture shows different morphology of arresting by natural fracture (during synchronous fracturing), partially penetrating the natural fracture (during two-step fracturing) and directly penetrating the natural fracture (during sequential fracturing). Different cement strengths of natural fracture are analyzed. The increase of strength of natural fracture can enhance the ability of hydraulic fracture penetrating the natural fracture. Hydraulic fracture is arrested by weak natural fracture (shear strength of 0.5 MPa), resulting in natural fracture opening. As hydraulic fracture intersecting with strong natural fracture (shear strength of 20 MPa), the hydraulic fracture can penetrate the natural fracture directly without natural fracture opening. [ABSTRACT FROM AUTHOR]