Search

A novel three-dimensional (3D) porous nickel-cobalt (Ni-Co) film on nickel foam is successfully prepared and further used as an efficient anode for direct urea-hydrogen peroxide fuel cell (DUHPFC). By varying the cobalt/nickel mole ratios into 0%, 20%, 50%, 80% and 100%, the optimized Ni-Co/Ni foam anode with a ratio of 80% is obtained in terms of the best cell performance among five anodes. Effects of the KOH and urea concentrations, the flow rate and operation temperature on the fuel cell performance are investigated. Results show DUHPFC with the 3D Ni-Co/Ni foam anode exhibits a higher performance than those reported direct urea fuel cells. The cell gives an open circuit voltage of 0.83 V and a peak power density as high as 17.4 and 31.5 mW cm −2 at 20 °C and 70 °C, respectively, when operating on 7.0 mol L −1 KOH and 0.5 mol L −1 urea as the fuel at a flow rate of 15 mL min −1 . Besides, when the human urine is directly fed as the fuel, direct urine-hydrogen peroxide fuel cell reaches a maximum power density of 7.5 mW cm −2 with an open circuit voltage of 0.80 V at 20 °C, showing a good application prospect in wastewater treatment. [ABSTRACT FROM AUTHOR]

Abstract: The open circuit potentials (OCPs) of H2O2 at Pt, Pd, Au, and glassy carbon electrodes are measured in H2SO4 and NaOH electrolyte solutions. Effects of concentration of H+, OH− and H2O2 as well as temperature on the OCP of H2O2 are investigated. The OCP of H2O2 is much lower than its theoretical reduction potential in both acidic and basic medium. The OCP is actually a mixed potential of H2O2 electroreduction and electrooxidation simultaneously occurring at electrode surfaces and it is more close to the equilibrium potential of H2O2 electrooxidation rather than electroreduction. The OCP of H2O2 is around 0.77–0.80V at [H+]=[H2O2]=1.0moldm−3 in H2SO4 solution and is about 0–0.06V at [OH−]=[H2O2]=1.0moldm−3 in NaOH at 298K on Pt, Pd, Au and GC electrodes. The OCP of H2O2 is independent of H2O2 concentration within the range of 0.01 to 1.0moldm−3. It increases approximately linearly with the logarithm of H+ concentration from 0.02 to 2.0moldm−3, decreases with the logarithm of OH− concentration from 0.01 to 1.0moldm−3 and decreases with increase of temperature from 278K to 333K. The linear equations were presented and discussed. [Copyright &y& Elsevier]

Abstract: Direct carbon fuel cells are promising power sources using solid carbon directly as fuel. Their performances significantly depend on the electrooxidation activity of carbon fuel. Electrooxidation of activated carbon particulates in molten Li2CO3–K2CO3 was investigated by potentiodynamic and potentiostatic method. Results indicated that the electrooxidation performance of activated carbon was significantly enhanced by pre-soaking with Li2CO3–K2CO3 and by treatment with HF, HNO3 and NaOH, respectively. The onset potential negatively shifted by around 100 mV and the current density increased by around 50 mA cm−2 after pre-soaking. The non-oxidant acids (HF) treatments are more effective than oxidant acid (HNO3) and base (NaOH) treatments. HF treated activated carbon exhibited the highest activity among all the samples. The enhancement in electrooxidation performance can be closely correlated with the increase in surface area and porosity caused by acid and base treatments. [Copyright &y& Elsevier]

Abstract: The direct carbon fuel cell is a special type of high temperature fuel cell that directly uses solid carbon as anode and fuel. As an electrical power generator for power plants, it has a higher achievable efficiency (80%) than the molten carbonate and solid oxide fuel cells, and has less emissions than conventional coal-burning power plants. More importantly, its solid carbon-rich fuels (e.g. coal, biomass, organic garbage) are readily available and abundant. In this review, some fundamental study results of electrochemical oxidation of carbon in molten salts are summarized. Recent developments in direct carbon fuel cell configurations and performance are also discussed. [Copyright &y& Elsevier]

A series of prototype direct methanol fuel cells (DMFCs) were constructed and operated under identical procedures and conditions except for the surface compositions of the anode electrocatalysts. The cathode electrocatalyst was Pt black (loading 2 mg/cm2, specific surface area: ca. 27 m2/g), the electrolyte membrane was Nafion™ 117, and the anode electrocatalysts were a series of Pt–Ru adatom (Pt–Ruad) nanoparticles (loading 2 mg/cm2, specific surface area: ca. 27 m2/g) prepared by a direct surface reductive deposition of Ruad onto Pt black. The optimum surface coverage of Pt by Ruad was ca. 33% for DMFCs operating at 60 °C. The optimum ranged from ca. 30 to 60% at 90 °C. A DMFC using Pt–Ruad nanoparticles supported on carbon (Vulcan XC-72™) as anode electrocatalyst was operated for 20 days at 8 h each day without loss of activity. These results, combined with those from an in situ cyclic voltammetry study, indicate that no significant Ruad dissolution and/or redistribution occurred during fabrication and operation of the prototype DMFCs. [Copyright &y& Elsevier]

We report the performance of a polymer electrolyte membrane direct 2-propanol fuel cell (DPFC). The cell consisted of a Pt-Ru (atomic ratio of 1:1) black anode, a Pt black cathode, and a Nafion®-117 membrane electrolyte. The cell was operated at 90 °C with aqueous 2-propanol as fuel and with oxygen as oxidant. The performance of the cell operating on 2-propanol is substantially higher than when it was operating on methanol at current densities lower than ∼200 mA/cm2. The electrical efficiency of the direct 2-propanol fuel cell is nearly 1.5 times that of the direct methanol fuel cell at power densities below 128 mW/cm2. Studies on the effects of electrocatalyst loading, of 2-propanol concentration, and of oxygen pressure on cell performance indicate that the cells operating on 2-propanol require lower anode and cathode loadings than cells operating on methanol. Cathode poisoning by 2-propanol is less severe than by methanol. Hydrogen gas evolution observed at the anode at low current densities indicated that catalytic dehydrogenation of 2-propanol occurred over the anode catalyst. A rapid voltage drop occurred at high current densities and after operating the cell for extended periods of time at constant current. The rapid voltage drop is an anode phenomenon. [Copyright &y& Elsevier]

The borohydride oxidation reaction (BOR) is the main reaction in the anode of direct borohydride fuel cells (DBFCs), which is also fundamental to highlight the advantages of DBFCs. However, the catalysis of BOR still faces many challenges. On the one hand, further breakthroughs in catalytic activity are sought to achieve high performance of the anode; on the other hand, the negative effects brought by the side reactions, including the bubble effect, loss of fuel utilization, poisoning of the catalyst, etc., are urgently needed to be mitigated. Essentially, the running of the anode is the catalysis of BOR, so the catalytic viewpoint is critical to solving the above problem. In this work, an updated review of the effects of electrode design and the modulation of the catalytic environment on the anode is provided. Specifically, the electrode design is reviewed mainly from the perspective of catalytic activity, selectivity, and protective strategies. Besides, the modulation of the catalytic environment is emphasized in the systematic configuration and reactant transfer engineering. This work is expected to provide an in-depth understanding of the catalysis of BOR and afford significant inspiration toward the design of the anode. In this work, an updated review of the effects of electrode design and the modulation of the catalytic environment on the anode of direct borohydride fuel cells is provided. [Display omitted] • Based on a catalytic perspective DBFC anodes were reviewed. • Engineering strategies for electrode design are summarized. • The effects of catalytic environmental on the anode are discussed. • Challenges and outlooks for the design of DBFC anodes are provided. [ABSTRACT FROM AUTHOR]

A novel electrode of PdCu nanoparticles modified free-standing reduced graphene oxide (rGO) framework (PdCu@rGOF) is fabricated via electrodeposition and chemical reduction and employed to the direct sodium borohydride-hydrogen peroxide fuel cell (DBHPFC). The resultant catalyst reveals excellent catalytic performance towards hydrogen peroxide (H 2 O 2) electroreduction reaction (HPRR) and sodium borohydride (NaBH 4) electrooxidation reaction (BOR) along with low activation energy (E a). Numerically, the PdCu@rGOF electrode delivers an HPRR current density of 455.2 mA cm−2 at 0 V (2 mol L−1 H 2 SO 4 +1.3 mol L−1 H 2 O 2). Additionally, the current density of BOR reaches up to 1065.3 mA cm−2 at 0 V for 2 mol L−1 NaOH and 0.3 mol L−1 NaBH 4. Meanwhile, the mechanism studies show that HPRR and BOR catalyzed by PdCu@rGOF mainly relates 2-electron-transfer process and quasi-8-electron-transfer process, respectively. Subsequently, PdCu@rGOF is assembled into a fuel cell, yielding the optimal power density of 188.9 mW cm−2. The open circuit potential (OCP) of DBHPFC is about 1.70 V at 293.15 K. The superior electrochemical performance of the optimized electrode can be attributed to the distinctive architecture and the strong adsorption and bond-breaking ability of Pd nanoparticles. This work indicates that the as-prepared PdCu@rGOF can be a promising catalyst for DBHPFC. [Display omitted] • A novel 3D through-hole rGOF framework has been successfully prepared. • PdCu@rGOF displays an excellent catalytic performance for HPRR and BOR. • PdCu@rGOF can be applied to both anode and cathode of DBHPFC. • DBHPFC presents high power density and operation stability. [ABSTRACT FROM AUTHOR]

Abstract: The synthesis, electrochemical analysis, and hydrogen-air fuel cell testing results for a new type of Se/Ru catalyst called Se/Ru(aq) were described in Part 1. In this second report, we present methanol tolerance studies and direct methanol fuel cell testing for the same catalyst. A “methanol-tolerant” catalyst does not oxidize methanol, nor becomes depolarized by its presence, which is a desirable property for DMFC cathodes used with methanol-permeable membranes or in mixed-reactant designs. In perchloric acid electrolyte, the Se/Ru(aq) catalyst was found to be highly tolerant to 1.0M methanol. More importantly, in fuel-cell testing as a DMFC cathode, Se/Ru(aq) was shown to be highly tolerant to methanol crossing through the membrane (from the anode side) up to a feed concentration of 17M. The results were compared to those obtained using unmodified Ru black and Pt black at the DMFC cathode, in order to gain insight into the catalyst function and to compare the performance to relevant benchmarks. Compared to Pt cathodes, the performance of Se/Ru(aq) is significantly better at high methanol concentrations (e.g., 17M), suggesting their use either in DMFCs with high methanol feed concentrations or in mixed-reactant fuel cells. [Copyright &y& Elsevier]

Abstract: The electrochemical performances of magnesium, magnesium–lithium–aluminum–cerium and magnesium–lithium–aluminum–cerium–yttrium as the anode of magnesium–hydrogen peroxide semi-fuel cells have been studied by methods of potentiodynamic, potentiostatic and electrochemical impedence measurements. The surface morphologies of magnesium and its alloys have been examined by scanning electron microscopy (SEM). It has been found that magnesium–lithium–aluminum–cerium and magnesium–lithium–aluminum–cerium–yttrium electrodes are less corrosion resistant than that of magnesium electrode in 0.7molL−1 NaCl solution and the corrosion current density decreases with the following order: magnesium

Electricity production and modeling of microbial fuel cell (MFC) from continuous beer brewery wastewater was studied in this paper. A single air-cathode MFC was constructed, carbon fiber was used as anode and diluted brewery wastewater (COD=626.58mg/L) as substrate. The MFC displayed an open-circuit voltage of 0.578V and a maximum power density of 9.52W/m3 (264mW/m2). Using the model based on polarization curve, various voltage losses were quantified. At current density of 1.79A/m2, reaction kinetic loss and mass transport loss both achieved to 0.248V; while ohmic loss was 0.046V. Results demonstrated that it was feasible and stable for producing bioelectricity from brewery wastewater; while the most important factors which influenced the performance of the MFC are reaction kinetic loss and mass transport loss. [Copyright &y& Elsevier]

The highly porous electrode of a crisscrossed CoNi nanosheets array grown on reduced graphene oxide decorated Ni foam (CoNi/rGO@Ni foam) is fabricated through a facile dip and dry method followed by electroreduction and electrodeposition methods. The phase composition and morphology of the electrode are characterized by XRD, SEM, TEM, and EDS. In single electrode tests, CoNi/rGO@Ni foam electrode displays an excellent catalytic performance (330 mA cm−2 at 0.6 V) and stability towards urea electrooxidation when comparing to Ni foam and CoNi nanosheets modified Ni foam (CoNi@Ni foam) electrode. Besides, a low initial oxidation potential of urea electro-oxidation to 0.14 V is achieved on the CoNi/rGO@Ni foam electrode. The introducing of rGO to the electrode greatly reduced the reaction activation energy from 14.47 to 10.35 kJ mol−1. Besides, large active surface area (261.67 cm2) is also obtained from the electrode. The CoNi/rGO@Ni foam anode exhibits a maximum power density of 12.58 mW cm−2 in direct urea-hydrogen peroxide fuel cell tests. Excellent performance shows in single electrode tests and fuel cell tests suggest that addition of rGO to the electrode is an easy and feasible method to enhance the performance of the catalyst. • Highly porous electrode: crisscrossed nanosheets array grows on rGO modified Ni foam. • The influence of rGO on the catalytic performance of the electrode was researched. • Low initial oxidation potential towards urea electro-oxidation was obtained. • Achieved an excellent performance and stability when practical use in DUHPFC. [ABSTRACT FROM AUTHOR]

An original three-dimensional self-supported reduced graphene oxide (rGO) foam is successfully prepared in this work. This novel support material, modified with Co nanosheets and Au nanoparticles, is employed as a high-performance catalyst for NaBH 4 electrooxidation under alkaline condition. The surface chemical component and morphology of the catalyst is characterized by X-ray diffraction pattern, X-ray photoelectron spectroscopy, scanning electron microscope. The synthesized electrode exhibits excellent performance (1.35 A cm−2 at 0 V) towards NaBH 4 electrooxidation. The unique structure of rGO foam caused a large electrochemical active surface area (EASA (Au) = 390 m2 g−1), low electrochemical impedance, as well as 55.4% utilization efficiency of NaBH 4. Also, catalytic kinetic parameters during the electrooxidation reaction of NaBH 4 in a low NaBH 4 concentration are investigated. Results indicate that oxidation of BH 4 − is a first-order reaction, and the exchanged number of electrons obtained at the CoAu/rGO foam electrode is 6.9. Finally, we practically apply it to a direct borohydride-hydrogen peroxide fuel cell (DBHPFC). This work suggests that the prepared rGO foam is an excellent current collector, and CoAu/rGO foam electrode is a promising anode catalyst to apply in DBHPFC. Image 1 [ABSTRACT FROM AUTHOR]

Catalytic performance and NaBH 4 utilization are two crucial concerns in the electrooxidation of NaBH 4. To improve the inherent properties of regular performance and low fuel utilization of the transition metal Co and Ni, an efficient anode catalyst of ultra-thin CoNi nanosheets modified novel 3D self-supported reduced graphene oxide foam is prepared in this work. The alkaline condition borohydride oxidation reaction on the prepared catalyst is investigated in a typical three-electrode system. The prepared catalyst shows a high performance due to the large electrochemical active surface area, low activation energy (8.29 kJ·mol−1), and the small electrochemical impedance it embraced. Linear scan voltammetry recorded in a low concentration of NaBH 4 suggests that borohydride oxidation is a first-order reaction on the prepared catalyst. Based on the unique structure of the catalyst, which is useful to capture the hydrogen and perform further oxidation of hydrogen, higher utilization of NaBH 4 achieved on the catalyst. Besides, the prepared anode catalyst applied to a direct borohydride-hydrogen peroxide fuel cell (DBHPFC). The results of polarization curve and power density curves, as well as stability research, all indicate that the as-prepared catalyst is a highly efficient anode material for application in DBHPFC. Unlabelled Image • Novel 3D self-supported rGO foam skeleton was prepared by a simple template method. • The catalytic activity of CoNi-NS/rGO foam is higher than CoNi-NS/Ni foam electrode. • Self-supported rGO foam matrix improved the utilization efficiency of NaBH4. • CoNi-NS/rGO foam anode catalyst exhibited highest power density of 140 mW·cm−2. [ABSTRACT FROM AUTHOR]

Porous Ni 2 P nanoflower supported on nickel foam (Ni 2 P@Ni foam) electrodes are synthesized via a simple hydrothermal growth strategy accompanied with further phosphating treatment. The prepared electrodes are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX) and transmission electron microscopy (TEM). Electro-catalytic performances towards urea electro-oxidation are tested by cyclic voltammetry (CV), chronoamperometry (CA) coupled with electrochemical impedance spectroscopy (EIS). By phosphating Ni(OH) 2 precursor, the final obtained Ni 2 P@Ni foam electrode presents a porous Ni 2 P nanoflower structure within abundant porosity, and so exposes a large amount of electro-catalytic active sites and electronic transmission channels to accelerate the interfacial reaction. Compared with Ni(OH) 2 @Ni foam precursor, the Ni 2 P@Ni foam catalyst exhibits more excellent electro-catalytic activity as well as lower onset oxidation potential. Remarkably, the Ni 2 P@Ni foam catalyst reaches a peak current density of 750 mA cm −2 with an onset oxidation potential of 0.24 V (vs. Ag/AgCl) accompanied by an excellent stability in 0.60 M urea with 5.00 M KOH solutions. Benefiting from the unique porous nanosheet structure, the as-synthesized Ni 2 P@Ni foam catalyst performs a highly enhanced catalytic behavior for alkaline urea electro-oxidation, indicating that the material can be hopefully applied in direct urea fuel cells. [ABSTRACT FROM AUTHOR]

Direct peroxide-peroxide fuel cell (DPPFC) employing with H 2 O 2 both as the fuel and oxidant is an attractive fuel cell due to its no intermediates, easy handling, low toxicity and expense. However, the major gap of DPPFC is the cathode performance as a result of the slow reaction kinetics of H 2 O 2 electro-reduction and thus the target issue is to design cathode catalysts with high performance and low cost. Herein, different with using noble metal of state-of-the-art, we have successfully synthesized ultra-fine Ni Fe ferrocyanide (NiFeHCF) nanoparticles (the mean particles size is 2.5 nm) through a co-precipitation method, which is used as the cathode catalyst towards H 2 O 2 reduction in acidic medium. The current density of H 2 O 2 reduction on the resultant NiFeHCF electrode after the 1800 s test period at −0.1, 0 and 0.1 V are 121, 93 and 76 mA cm 2 , respectively. Meanwhile, a single two-compartment DPPFC cell with NiFeHCF nanoparticles as the cathode and Ni/Ni foam as the anode is assembled and displayed a stable OCP of 1.09 V and a peak power density of 36 mW cm −2 at 20 °C, which is much higher than that of a DPPFC employed with Pd nano-catalyst as cathode. [ABSTRACT FROM AUTHOR]

Thorn-like Ni@TiC NAs and flake-like Co@TiC NAs electrodes without any conductive agent and binder are simply fabricated by the potentiostatic electrodeposition of Ni and Co catalysts on the TiC nanowire arrays (NAs). The electrocatalytic activity of H 2 O 2 oxidation on the Ni@TiC NAs electrodes is better than that on the Co@TiC NAs electrodes. The Ni@TiC NAs electrodes demonstrate a rough surface and have many nano-needles on the rod edges, which assures the high utilized efficiency of Ni catalysts. These particular three-dimensional structures may be very suitable for H 2 O 2 electrooxidation. The anodic current of Ni@TiC NAs anode reaches 0.32 A cm −2 at 0.3 V in 1.0 M H 2 O 2 + 4 M KOH solution. The DPFCs employing Ni@TiC NAs anodes display the peak power density of 30.2 mW cm −2 and open circuit voltage of 0.90 V at 85.1 mA cm −2 with desirable cell stability at 10 mL min −1 flow rate and 20 °C, which is much higher than those previously reported. [ABSTRACT FROM AUTHOR]

A bi-functional electrode material of self-supporting N-doped C foam grown Pd nanoparticles (Pd@N/C-8 foam) for NaBH 4 electrooxidation and H 2 O 2 reduction reaction is successfully prepared. The Pd@N/C-8 foam electrode is fabricated by sacrificial template synthesis of N/C foam followed by 8 repetitive Pd impregnation reduction cycles. The Pd@N/C-8 foam electrode exhibits an extraordinary catalytic performance (642 mA cm−2 at −0.2 V) in 2 mol L−1 NaOH and 0.3 mol L−1 NaBH 4 , which is due to the large electrochemical active surface area, low activation energy (E a = 10.34 kJ mol−1) and 60.83% utilization efficiency of NaBH 4. Besides, its catalytic density for H 2 O 2 electroreduction reaches 648 mA cm−2 at −0.2 V in 2 mol L−1 H 2 SO 4 +1.3 mol L−1 H 2 O 2. The kinetic parameters show that the electrooxidation of BH 4 − and the electroreduction of H 2 O 2 on Pd@N/C-8 foam electrode are first-order reactions, and the number of transferred electrons are 5.8 and 1.56, respectively. Further exploration of Pd@N/C-8 foam electrode on the direct sodium borohydride-hydrogen peroxide fuel cell (DBHPFC) displays the maximum power density of 137 mW cm−2 and a superior stability. In view of the excellent performance, Pd@N/C foam will be a highly efficient electrode material of DBHPFC. • A novel Pd decorated 3D porous N/C foam has been successfully prepared. • Pd@N/C-8 foam can be applied to both anode and cathode of DBHPFC. • Pd@N/C-8 foam can effectively improve the fuel utilization. • DBHPFC presents excellent operation stability. [ABSTRACT FROM AUTHOR]

Nickel-cobalt nanowire arrays (Ni-Co NWAs) electrode is prepared by one-step galvanostatic electrodeposition with a polycarbonate membrane as the template. By adjusting the Co proportion in the Ni and Co bath solution into 10%, the optimal Ni-Co NWAs electrode in terms of relatively lower onset potential and highest current density towards urea electro-oxidation is obtained. Its catalytic performance is investigated by constructing single direct urea/hydrogen peroxide (H 2 O 2 ) fuel cell. Results show that a peak power density of 7.4 mW cm −2 and an open circuit voltage of 0.92 V are achieved at room temperature when 9.0 mol L −1 KOH and 0.33 mol L −1 urea are used as the anolyte, H 2 SO 4 and H 2 O 2 as the catholyte. Additionally, the urea/H 2 O 2 fuel cell also demonstrates excellent stability during short term duration test. [ABSTRACT FROM AUTHOR]

A novel three-dimensional carbon- and binder-free nickel nanowire arrays (Ni NAs) electrode is successfully fabricated by a facile galvanostatic electrodeposition method using polycarbonate membrane as the template. The Ni NAs electrode achieves a oxidation current density (divided by the electroactive surface areas of Ni) of 25.1 mA cm −2 in 4 mol L −1 KOH and 0.9 mol L −1 H 2 O 2 at 0.2 V (vs. Ag/AgCl) accompanied with a desirable stability, which is significantly higher than the catalytic activity of H 2 O 2 electro-oxidation achieved previously with precious metals as catalysts. The impressive electrocatalytic performance is largely attributed to the superior 3D open structure and high electronic conductivity, which ensures the high utilization of Ni surfaces and makes the electrode have higher electrochemical activity. The apparent activation energy of H 2 O 2 electro-oxidation on the Ni NAs catalyst is 13.59 kJ mol −1 . A direct peroxide–peroxide fuel cell using the Ni NAs as anode exhibits a peak power density of 48.7 mW cm −2 at 20 °C. The electrode displays a great promise as the anode of direct peroxide–peroxide fuel cell due to its low cost, high activity and stability. [ABSTRACT FROM AUTHOR]

Pt-modified Co nanosheet@carbon sponge (Pt-Co NS@carbon sponge) electrode is synthesized via a facile sponge carbonization method coupled with a direct Co electrodeposition and Pt chemical-deposition. The obtained electrodes are characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX) and transmission electron microscopy (TEM). The catalytic performances of H 2 O 2 electroreduction in alkaline medium are investigated by cyclic voltammetry (CV), chronoamperometry (CA) and electrochemical impedance spectroscopy (EIS). The Pt-Co NS@carbon sponge electrode exhibits unique nanosheet structure on the three-dimensional (3D) porous network skeleton with a large surface area and displays excellent catalytic performance. The Pt-Co NS@carbon sponge electrode achieves a reduction current density of −1.38 A cm −2 mg −1 in 3.0 mol L −1 KOH and 1.5 mol L −1 H 2 O 2 at −0.50 V (vs. Ag/AgCl) accompanied with a desirable stability, which is significantly higher than the catalytic activity of H 2 O 2 electroreduction achieved previously with precious metals as catalysts. The impressive electrocatalytic performance is largely attributed to the superior 3D open structure and high electronic conductivity, which ensures the full utilization of Pt surfaces and makes the electrode have higher electrochemical activity. Original Pt-Co NS@carbon sponge electordes have a great potential for the application in fuel cells due to its facile preparation, high performance and low cost. [ABSTRACT FROM AUTHOR]

Highly porous nickel@carbon sponge electrode with low cost is synthesized via a facile sponge carbonization method coupled with a direct electrodeposition of Ni. The obtained electrodes are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX). The catalytic performances of urea electro-oxidation in alkaline medium are investigated by cyclic voltammetry (CV) and chronoamperometry (CA). The Ni@carbon sponge electrode exhibits three-dimensional open network structures with a large surface area. Remarkably, the Ni@carbon sponge electrode shows much higher electrocatalytic activity and lower onset oxidation potential towards urea electro-oxidation compared to a Ni/Ti flat electrode synthesized by the same procedure. The Ni@carbon sponge electrode achieves an onset oxidation potential of 0.24 V (vs. Ag/AgCl) and a peak current density of 290 mA cm −2 in 5 mol L −1 NaOH and 0.10 mol L −1 urea solutions accompanied with a desirable stability. The impressive electrocatalytic activity is largely attributed to the high intrinsic electronic conductivity, superior porous network structures and rich surface Ni active species, which can largely boost the interfacial electroactive sites and charge transfer rates for urea electro-oxidation in alkaline medium, indicating promising applications in fuel cells. [ABSTRACT FROM AUTHOR]

Abstract: Running of direct 2-propanol fuel cell generates liquid acetone as the main product in the anode compartment. Its concentration continuously increases during cell operation. Its effect on the electrooxidation of 2-propanol at the anode catalyst deserves to be addressed. In this study, the influence of acetone concentration and reaction temperature on the electrooxidation of 2-propanol at Pt and Au electrode in alkaline electrolyte is investigated by cyclic voltammetry and chronoamperometry. The results show that the rate of 2-propanol electrooxidation at Pt and Au electrode is remarkably diminished with the increase of acetone concentration. When the concentration of acetone reaches 0.1molL−1, the oxidation current of 2-propanol at Pt and Au electrode decreases by around 50% and 30%, respectively. The effect of acetone can be attributed to its competitive adsorption with 2-propanol on electrodes surface, leading to the poison of electrodes. Increase of reaction temperature decreases the oxidation current of 2-propanol at Au electrode. Au electrode is more tolerant to acetone than Pt electrode at low acetone concentration. Results of this study suggest that new acetone insensitive electrocatalysts are needed for 2-propanol electrooxidation in alkaline electrolytes. [Copyright &y& Elsevier]

Abstract: Activation of the MmNi4.03Co0.42Mn0.31Al0.24 hydrogen storage alloy electrode is performed by immersing the electrode in a solution containing 6.0moldm−3 NaOH and 0.1 mol dm−3 NaBH4. The effects of activation on the electrocatalytic activity of the electrode for NaBH4 oxidation are investigated by cyclic voltammetry and chronoamperometry. Immersion activation greatly improves the electrocatalytic activity of the alloy electrode. Hydrogen was absorbed in the alloy during the immersion activation treatment and its electrooxidation is responsible for the high initial oxidation current. The stabilized current mainly results from the direct oxidation starting from the borohydride species. The effects of activation on structure and surface chemistry of the alloy are also discussed. [Copyright &y& Elsevier]

Bimetallic oxide CoMn 2 O 4 with nano-peony structure is prepared on Ni foam by a traditional hydrothermal process. Then constant-potential electrodeposition is applied to anchor Pd nanoparticles on CoMn 2 O 4 to form an electrode of Pd nanoparticles modified CoMn 2 O 4 (PCMN electrode) for H 2 O 2 electroreduction. The combination of Pd and CoMn 2 O 4 effectively reduces the dosage of noble metal. Besides, no binder is involved in the preparation which cuts the electrode cost and avoids the poor stability of traditional electrodes produced with binders. Scanning electron microscopy, X-ray diffraction and transmission electron microscopy are operated to investigate the structure and composition of the electrode. And the electrochemical behavior of the electrode is characterized by cyclic voltammetry and chronoamperometry. In 0.7 mol L−1 H 2 O 2 and 3 mol L−1 NaOH, a reduction current density of 580 mA cm−2 (normalized by geometric area) at −0.8 V on the electrode is obtained which reveals large capacity for actual application in H 2 O 2 -based fuel cell. A binder-free electrode of Pd nanoparticles anchored to nano-peony CoMn 2 O 4 was prepared and the synergy effect of Co, Mn and Pd highly improved the catalytic activity toward H 2 O 2 reduction. Unlabelled Image • Pd modified CoMn 2 O 4 electrode with special nano-peony structure was synthesized. • The special nano-peony structure provides more active sites for H 2 O 2 reduction. • The synergy effect of Co, Mn and Pd highly improved the catalytic activity. [ABSTRACT FROM AUTHOR]