Search

Abstract: The effects of six types of aprotic organic solvents on the discharge performance and discharge products in Li-O2 batteries are systematically investigated. A large amount of Li2O2 is identified in the air electrodes discharged in glyme-based electrolytes, while only a small amount of Li2O2 is detected in the air electrodes discharged in the electrolytes of nitrile, ionic liquid, phosphate, and sulfoxide. Li2CO3 and LiF are also found as byproducts whose compositions are related to the solvents. Li2CO3 is produced from oxidation and decomposition of the solvent, not from the oxidation of the carbon-based air electrode, as revealed by using a 13C-labeled carbon electrode and the solid-state 13C-magic angle spinning nuclear magnetic resonance technique. LiF in the discharge products can be attributed to the attack of superoxide radical anions to the Teflon binder and/or the F-containing imide salt. The formation of these byproducts will significantly reduce the Coulombic efficiency and cycle life of the Li-air batteries. Among the studied solvents, dibutyl diglyme is the suitable solvent for Li-O2 batteries based on its overall properties. However, better electrolytes that can ensure the formation of Li2O2 but minimize other reaction products need to be further investigated for long cycling rechargeable Li-air batteries. [Copyright &y& Elsevier]

Abstract: It is well known that LATP (Li1+x+y Al x Ti2−x Si y P3−y O12) glass is a good lithium (Li)-ion conductor. However, the interaction between LATP glass and H+ ions in aqueous electrolytes (including the diffusion and surface adsorption of H+ ions) needs to be well understood before the long-term application of LATP glass in an aqueous electrolyte can be realized. In this work, we investigate H+-ion diffusion in LATP glass and their interactions with the glass surface using both experimental and modeling approaches. Our results indicate that the apparent H+-related current observed in the initial cyclic voltammetry scan should be attributed to the adsorption of H+ ions on the LATP glass rather than the bulk diffusion of H+ ions. Furthermore, density functional theory calculations indicate that the H+-ion diffusion energy barrier (3.21 eV) is much higher than that for Li+ ions (0.79 eV) and Na+ ions (0.79 eV) in a NASICON-type LiTi2(PO4)3 material. As a result, H+-ion conductivity in LATP glass is negligible at room temperature. However, significant surface corrosion was found after the LATP glass in a strong alkaline electrolyte. Therefore, to prevent LATP glass from corrosion, appropriate electrolytes must be developed for long-term operation of LATP in aqueous Li–air batteries. [Copyright &y& Elsevier]

Abstract: In this paper, we report the electrochemical characteristics of a novel cathode material, Li2CoPO4F, prepared by solid-state reactions. The solid-state reaction mechanism involved in synthesizing the Li2CoPO4F also is analyzed in this paper. When cycled between 2.0V and 5.0V during cyclic voltammetry measurements, the Li2CoPO4F samples present one, fully reversible anodic reaction at 4.81V. When cycled between 2.0V and 5.5V, peaks occurring at 4.81V and 5.12V in the first anodic scan evolved to one broad oxidative, mound-like pattern in subsequent cycles. Correspondingly, the X-ray diffraction (XRD) pattern of the Li2CoPO4F electrode discharged from 5.5V to 2.0V is slightly different from the patterns exhibited by a fresh sample and the sample discharged from 5.0V to 2.0V. This difference may correspond to a structural relaxation that appears above 5V. In the constant current cycling measurements, the Li2CoPO4F samples exhibited a capacity as high as 109mAhg−1 and maintained a good cyclability between 2.0V and 5.5V vs. Li/Li+. XRD measurements confirmed that the discharged state is Li2CoPO4F. Combining these XRD results and electrochemical data proved that up to 1mol Li+ is extractable when charged to 5.5V. [ABSTRACT FROM AUTHOR]

Rechargeable lithium (Li) metal batteries with conventional LiPF 6 -carbonate electrolytes have been reported to fail quickly at charging current densities of about 1.0 mA cm −2 and above. In this work, we demonstrate the rapid charging capability of Li||LiNi 0.8 Co 0.15 Al 0.05 O 2 (NCA) cells can be enabled by a dual-salt electrolyte of lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) and lithium bis(oxalato)borate (LiBOB) in a carbonate solvent mixture. The cells using the LiTFSI-LiBOB dual-salt electrolyte significantly outperform those using the LiPF 6 electrolyte at high charging current densities. At the charging current density of 1.50 mA cm −2 , the Li||NCA cells with the dual-salt electrolyte can still deliver a discharge capacity of 131 mAh g −1 and a capacity retention of 80% after 100 cycles. The Li||NCA cells with the LiPF 6 electrolyte start to show fast capacity fading after the 30th cycle and only exhibit a low capacity of 25 mAh g −1 and a low retention of 15% after 100 cycles. The reasons for the good chargeability and cycling stability of the cells using the LiTFSI-LiBOB dual-salt electrolyte can be attributed to the good film-formation ability of the electrolyte on the Li metal anode and the highly conductive nature of the sulfur-rich interphase layer. [ABSTRACT FROM AUTHOR]

The practical application of lithium (Li) metal anode in rechargeable Li batteries is hindered by both the growth of Li dendrites and the low Coulombic efficiency (CE) during repeated charge/discharge cycles. Recently, we have discovered that CsPF 6 as an electrolyte additive can significantly suppress Li dendrite growth and lead to highly compacted and well aligned Li nanorod structures during Li deposition on copper substrates. In this paper, the effect of CsPF 6 additive on the performance of rechargeable Li metal batteries with lithium iron phosphate (LFP) cathode is further studied. Li|LFP coin cells with CsPF 6 additive in electrolytes show well protected Li anode surface, decreased resistance, enhanced rate capability and extended cycling stability. In Li|LFP cells, the electrolyte with CsPF 6 additive shows excellent long-term cycling stability (at least 500 cycles) at a charge current density of 0.5 mA cm −2 without internal short circuit. At high charge current densities, the effect of CsPF 6 additive becomes less significant. Future work needs to be done to protect Li metal anode, especially at high charge current densities and for long cycle life. [ABSTRACT FROM AUTHOR]

In this work, localized high concentration electrolytes (LHCEs) based on tetramethylene sulfone (TMS) were designed. Similar to LHCEs based on other solvents, TMS-based LHCEs can achieve excellent compatibility with high energy density lithium-ion batteries (LIBs) when combined with a proper additive. The unique solvation structure of LHCEs facilitates the synergetic decomposition of anion, solvent and additive in the solid electrolyte interphase (SEI) formation. Proper combinations of the three constituents of the solvation sheaths in LHCEs can promote the formation of highly effective SEI on graphite negative electrode. The absence of LiPF 6 in LHCEs also suppresses the degradation of positive electrode materials in LIBs. The superior interphasial properties of LHCEs are the key to realizing the long lifespan of high energy density LIBs. • Tetramethylene sulfone (TMS) based LHCEs with different additives were studied. • Additive-free TMS-LHCE outperforms conventional electrolyte in Gr.||Ni-rich LIBs. • Proper additives in TMS-LHCE can further boost performance of Gr.||Ni-rich LIBs. • Electrolyte solvation structure/content govern interphase and battery performance. [ABSTRACT FROM AUTHOR]