Search

Biocomposites have major advantage in term of weight saving thanks to lower densities compared to conventional materials; this property also allows a reduction of environmental impacts which is beneficial for the automotive industry. In addition, they maintain rather good mechanical properties after recycling cycles which makes possible to consider other end-of-life scenarios than incineration or landfill. In this work, we studied two potential routes for the recycling of moulding wastes from poly-(propylene)-flax nonwovens. By representing close to 25%-wt, these wastes are a major industrial problem, inducing additional recycling or treatment costs. In a first step, the parts were grinded and reincorporated at different weight fractions into virgin nonwovens. Up to 30%-wt of reincorporated wastes, results showed good mechanical performances for recycled nonwovens, especially in bending mode. In a second stage, scraps were grinded and then compounded for injection moulding applications. Their good rheological behavior and ability to conserve fibre lengths during extrusion made possible to formulate competitive materials in terms of tensile performances. [ABSTRACT FROM AUTHOR]

Environmental awareness of the global waste problem has driven the development of new green composites made from either renewable or biodegradable materials. Among the variety of available green composites, natural composites based on poly-lactic acid (PLA) have shown noteworthy performance due to their short degradation time after disposal, good strength, and ease of processing by conventional methods. In particular, green composites manufactured with PLA matrix reinforced with Manicaria Saccifera fabric (MF) display mechanical properties that have shown to be very competitive compared with similar materials. In this study, the tensile properties of a green composite of PLA reinforced with MF are optimized by using a Taguchi method approach. The processing parameters, fabric chemical treatment parameters, compression molding parameters, and fiber content are analyzed simultaneously to yield the optimum biocomposite properties. The predicted optimum parameters are experimentally verified. Tensile tests and scanning electron microscope (SEM) analysis are used. Significant improvements on both the tensile strength (114.2%), and the elastic modulus (120.6%) of the biocomposite are achieved. [ABSTRACT FROM AUTHOR]

Highlights: [•] Coir-polypropylene biocomposites were manufactured using hot press technique. [•] OH groups in raw coir cellulose were converted to OH−Cr groups during treatment. [•] SEM indicates improved interfacial adhesion between coir and PP upon treatment. [•] Chemically treated composites yielded the best set of mechanical properties. [ABSTRACT FROM AUTHOR]

Abstract: For the first time, biocomposites from wheat by-products, i.e. wheat gluten and wheat straw fibers, were prepared using a thermomechanical process. Three types of wheat straw fibers displaying contrasted sizes (median diameter d 50 =1.1mm, 62μm and 8μm), morphologies and surface reactivities were prepared by successive grinding processes (cut milling (CM), impact milling (IM) and ball milling (BM), respectively). The main objectives of the present study were (i) to gain further scientific knowledge about the impact of fibers characteristics on the mechanical properties of these composite materials, and (ii) to evaluate in which extent the addition of wheat straw fibers could decrease the final cost of materials without altering their mechanical properties. Mechanical properties were assessed through tensile tests and discussed in relation to the structure of materials, especially to the interfacial adhesion between the fiber and the matrix. Globally, an increasing fiber content up to 11.1vol% led to an increase in both the Young''s modulus and the stress at break, and to a reduction in the strain at break. Experimental Young''s moduli were well predicted by the Tsai–Pagano model for the three types of fibers. Data of specific mechanical energy consumed upon processing, contact angle measurements and observations of cryo-fractured surfaces allowed to demonstrate that the adhesion at the interface wheat straw fiber/wheat gluten was improved by (i) an increased hydrophobicity of wheat straw fibers, which was induced by successive grinding, and (ii) a higher specific surface of fibers which was favoured in the case of small fibers. The interfacial adhesion was improved in the order BM>IM>CM whereas the fiber aspect ratio decreased in the order CM>IM>BM. Thus, a competition between these parameters could occur, explaining why no significant difference in reinforcing effect was achieved between the three types of fibers. Finally, the reinforcing effect of wheat straw fibers was also ascribed to a deplasticizing effect, which was particularly pronounced for BM wheat straw fibers. [Copyright &y& Elsevier]

Abstract: This work describes a truss-core structure made of hemp/epoxy biocomposite based on a topology with auxetic (negative Poisson’s ratio) characteristics. Epoxy-based composites with 25wt.% of hemp yarns have been manufactured and characterized with tensile and flexural tests. Truss-core hexagonal chiral panels with the biocomposite core have been produced using a Resin Transfer Molding technique. The panels have been subjected to standard transverse shear tests, and their properties predicted with a Finite Element nonlinear modeling. The results show that the hexachiral biocomposite truss core exhibits specific shear modulus and strength significantly higher compared to the ones observed in previous demonstrators made of polymeric core. [Copyright &y& Elsevier]

Abstract: In this work, a starch-based biopolymer was reinforced with flax strands. Composite materials at different fiber content were obtained by means of high-shearing mixing followed by injection molding processing. The evaluation of the mechanical properties gave a significant increase of the strength and stiffness of composites with the percentage of flax strands. The enhancement was analyzed in terms of compatibility and extension of the adhesion at fiber–matrix interface. The intrinsic mechanical properties of the reinforcement were measured and the behavior of the obtained composites was studied in terms of the modified rule of mixtures and the modified Halpin–Tsai equations. [Copyright &y& Elsevier]