Search

In this paper, a bi-stable piezoelectric energy harvester based on the bi-stable hybrid composite laminate with a new stacking sequence design is proposed. The new stacking sequence enables this bi-stable energy harvester to have some unique features, such as uniform strains of piezoelectric elements and symmetric stable configurations. Meanwhile, the new stacking sequence design enhances the room to adjust its natural frequency such that this proposed harvester allows for adjusting to lower frequency range and increasing the inertia by a tip mass to lower the demand of excitation level in comparison to previous settings. A finite element analysis is developed to investigate the static and dynamic characteristics of this new bi-stable energy harvester. A simple numerical model with a modified version of the Duffing equation is developed based on the unique nonlinear restoring force obtained from finite element analysis to describe the fundamental response characteristics of this nonlinear bi-stable energy harvester. Numerical simulations and experiments are carried out at different harmonic excitation levels ranging from 10 to 40 Hz. The results verify that the proposed model can reasonably capture the dynamic characteristics of this broadband bi-stable energy harvester. The output powers were measured under different vibration patterns. Maximum power of 31.1 mW was generated under large-amplitude and high-energy orbits cross-well vibration pattern at an excitation frequency of 22 Hz and acceleration of 3 g ( g  = 9.8 m/s 2 ). [ABSTRACT FROM AUTHOR]

Bi-stable composite laminates with piezoelectric transducers have been shown to capture energy over a wide frequency range and deliver significantly greater energy than resonant devices. In this work, the influence of lay-up design on the performance of bi-stable piezoelectric energy harvester (BPEH) based on bi-stable hybrid symmetric laminate (BHSL) is analyzed and verified. The initial voltage induced by stable configuration and longitudinal curvature of BPEH with different lay-up and hybrid width were calculated and analyzed by a static finite element analysis. The lay-up can vary initial voltage and longitudinal in opposite directions, and hybrid width can adjust these two variables in the same direction. The strain variations of piezoelectric transducer between two stable configurations were also analyzed. The initial voltage of BPEH depends on strain variations in the two directions. And then the finite element results are verified by experiment. Three types of BPEH were manufactured and actuated by two methods to measure their output powers. These BPEHs presented different dynamic responses, and the output powers under different vibration modes were measured. The highest output power of BPEH in this work is 42.2 mW and the highest power density is 78.1 mW/cm 3 . [ABSTRACT FROM AUTHOR]

This paper focuses on a study of the snap-through behavior of a family of bi-stable plates constructed by hybrid symmetric laminates with a cantilever boundary. Involving shape change and actuation demand, a deep understanding of the snap-through behavior is of particular importance since this bi-stable laminate is often served as a host structure of energy harvester or a morphing structure. The snap-through behavior is obtained using two displacement-controlled finite element procedures provided in the commercial software ABAQUS and the results are verified by experiments. The entire equilibrium path of reaction force-displacement response with a couple of zero load crossings is captured by the 'Static, Riks' procedure to reveal the potential nonlinear structural behavior. The practical situation of the reaction force-displacement curve is obtained by the 'Static, General' procedure which exhibits consistent results with experiments. Several characteristics, such as snap-down, hysteresis, negative stiffness, and even zero stiffness are captured. A parametric study including lay-up design and length is also carried out using the finite element model and verified by experiments. The results show that the lay-up design not only can fundamentally change the snap-through response but also influences other characteristics of this bi-stable laminate including stable shape, and the length is a relatively reliable parameter to alter the snap-through features, e.g. peak force and hysteresis performance. [ABSTRACT FROM AUTHOR]

The resulting oscillation of bi-stable hybrid symmetric laminate could enable broadband energy harvesting via piezoelectric transduction. The aim of this work is to investigate its dynamic behaviors to provide the basis for designing broadband energy harvester. This paper proposes the dynamic analysis of this bi-stable laminate, focusing on the intra-well dynamics around its stable states and the inter-well dynamics between two stable states. Two types of stacking sequence are performed for this bi-stable laminate, and experimental testing with different harmonic excitations is carried out for each type of this bi-stable laminate. The strain responses at three positions are monitored to investigate the dynamic responses. A finite element model is also developed to analyze the static strain distribution and capture the dynamics. The results show that the laminates exhibit intra-well response under low-level excitation, and the inter-well response at a particular range frequency appears when excitation level increases. Different types of inter-well response mode involving the snap-through behavior are obtained in experiments, such as intermittent inter-well vibration and chaotic vibration. The presented results essentially highlight the need for considering the stacking sequence associated with the dynamics while designing the hybrid bi-stable symmetric laminate to obtain the desirable nonlinear response. [ABSTRACT FROM AUTHOR]