Search

This study investigates the load-carrying mechanism and proposes precise strength prediction methods for hole threads in Thread-fixed One-side Bolts bolted curved T-stubs to circular steel tube connections. A series of parametric analysis was performed with an advanced 3D finite element model considering critical parameters including tube wall thickness, bolt angle and bolt size. The axial load distribution along the hole threads and the shear stress distribution at the thread root were analyzed in detail. It was found that there were three typical load distribution patterns along hole threads, which were (1) linear pattern; (2) concave parabola pattern; and (3) convex parabola pattern, and the ratio of bolt stiffness to tube wall stiffness was identified as the pivotal factor affecting the axial load distribution. Meanwhile, the analysis results indicated that the bending moment on the TOBs did not affect the load distribution along hole threads, but led to a non-uniform stress distribution along the thread in the same turn. In the end, the prediction formulas for the carrying capacity of hole threads are presented by modifying Yamamoto's equation based on the analysis findings. The formulas are validated against the finite element analysis results and previous test results. The prediction can reach the highest accuracy when adopting the proposed failure criterion 2, with average errors of − 0.001 and − 0.002, respectively, demonstrating the accuracy and reliability. • An advanced 3D finite element model for bolted connections was developed. • The load distribution along hole threads were analyzed in detail. • Three typical load distribution patterns along hole threads were found. • Proposing methods to predict the load-carrying capacity of hole threads. [ABSTRACT FROM AUTHOR]

The seismic behaviour of hybrid coupled walls (HCWs) made of a single reinforced concrete (RC) wall connected to two steel side columns through steel links, named as single-pier HCWs (SP-HCWs), is studied through nonlinear finite element simulations. The design concept is that the steel links are intended to work as dissipative elements while the steel side columns and the RC wall should remain elastic. Given that previous studies highlighted difficulties in avoiding damage at the base of the RC wall due to the concentration of bending moment, this study focuses on a special configuration providing very limited damage at the base of the RC wall that could be rapidly and economically repaired. The original scheme of SP-HCW with fixed base is modified introducing a hinged connection combined with vertical steel elements, called corner components. A ductile design methodology is proposed and applied for proportioning 54 case studies with different building heights, coupling ratios, height-to-length ratios of the RC wall, in addition to different base conditions (fixed base, hinged base with corner components designed as non-dissipative elements, hinged base with corner components designed as dissipative elements). Results of nonlinear finite element analyses validate the design methodology and highlight the potentialities of the proposed solutions, showing the benefits of a hinged base with corner components. • The seismic performance of single-pier steel and concrete hybrid coupled walls is studied. • Focus is made on alternative hinged base solutions to protect the wall from damage. • A seismic ductile design procedure is proposed and applied to a wide set of case studies. • Results provide insights into the benefits of the developed base configurations. [ABSTRACT FROM AUTHOR]

Six T-shaped welded multi-partition composite members were tested under eccentric compression loading by considering the influence of eccentricity and eccentric angle. The test results showed that no weld tearing occurred when the specimen was damaged, indicating that the two vertical welds could ensure the overall working performance of the specimen. The specimens exhibited the smallest bearing capacity when failing along the asymmetric axis, which was the most dangerous situation. The parametric analysis is conducted by a verified finite element model considering the influence of the slenderness ratio, section height-to-width ratio, section depth-to-width ratio, concrete and steel grade, steel ratio, and eccentric angle. If concrete contributes a larger proportion to the bearing capacity, the interaction curve of axial force and bending moment tends to protrude. Conversely, the interaction curve of axial force and bending moment gradually shrinks as the slenderness ratio increases. Based on this observation, a calculation method of T-shaped welded multi-partition composite members under eccentric compressive loading along the asymmetric axis is proposed by considering the effect of the slenderness ratio. Formulas for bearing capacity under biaxial eccentric compression are proposed based on the results of the parametric analysis. • Eccentric compression of T-shaped welded multi-partition composite members was studied through experiments and FE analysis. • The measured torsion angle confirms the good torsional capacity of T-shaped composite members. • The effects of the slenderness ratio and biaxial eccentricity on the bearing capacity of the specimen are studied. • The N - M curve of T-shaped composite members under eccentric compression loading along the asymmetric axis is proposed. [ABSTRACT FROM AUTHOR]

This study examined the hysteretic behaviour of Square Hollow Section (SHS) T- and X-joints subjected to cyclic in-plane bending moments. A nonlinear finite element software, Abaqus, was used to investigate SHS T- and X-joint seismic performance. Prior to the parametric study, the numerical model was validated based on the available test results in the literature. A comprehensive parametric study employed validated finite element models to evaluate the influence of critical geometric parameters, including the brace-to-chord width ratio (β) and the chord width-to-thickness ratio (γ). The results of the finite element analyses regarding ductility, flexural strength, and energy dissipation behaviour of SHS T- and X-joints under quasi-static cyclic in-plane bending were evaluated. Based on the hysteretic curves, increasing β generally leaded to higher initial stiffness and moment capacity in SHS joints, considerably reducing joint rotation. Conversely, the joints with larger γ exhibited reduced initial stiffness and moment capacity. Besides, the Eurocode 3 EN1993-1-8 predictions for the ultimate flexural strength of the joints are found to be conservative compared to finite element results. The results also revealed that the SHS T- and X-joints showed satisfactory ductility levels under in-plane bending load. It was observed that the SHS T- and X-joints with high β and low γ are advantageous for absorbing energy under seismic loads. These findings offered valuable insights for the seismic-resistant design of structures incorporating SHS joints, aiding in selecting optimal configurations based on specific performance requirements. • This paper presents a numerical study of hysteretic behaviour of SHS T- and X-joints with IPBM. • An increase in β ratio generally corresponded to higher initial stiffness, moment capacity, ductility. • The joints with large γ ratio exhibited reduced initial stiffness, moment capacity and ductility. • Eurocode 3 predictions were conservative in estimating the ultimate flexural strength of the SHS T- and X-joints under IPBM. • SHS T- and X-joints with high β and low γ were advantageous for absorbing energy under seismic loads. [ABSTRACT FROM AUTHOR]

Single-point mooring (SPM) system has been used in offshore engineering for its superiority in overcoming severe sea conditions. However, researches focused on the interaction mechanism between the anchor pile and soil in SPM systems remains insufficient, especially regarding the calculation method for oblique pullout bearing capacity that considers padeye depth. Based on the p-y curve method and load transfer method, this paper presents a simple prediction method for the behavior of anchor piles embedded in sand under oblique pullout load. The theoretical predictions are validated through comparing with results from the three-dimensional finite element method and existing centrifuge model tests. The effect of the loading angle and the padeye depth are analyzed and discussed. A negative bending moment peak and axial force discontinuity phenomenon appear at the padeye depth. The optimal padeye depth for anchor piles in this study ranges from approximately 0.53 to 0.80 times the pile length. When the padeye depth is less than 0.33 times of the pile length, the ultimate bearing capacity of the anchor pile increases with increasing load angles. Conversely, when the padeye depth exceeds 0.33 times the pile length, the ultimate bearing capacity decreases with the increasing load angles. [ABSTRACT FROM AUTHOR]

This paper presents the results from two full-scale transversally stiffened plate girder's load tests in shear and bending. The plate girder's internal stiffener forces and shear buckling resistance are estimated using the web and stiffener measured strains. These results show that the reported axial compression and bending moment of the intermediate transverse stiffeners for the tested plate girder are 70% of the FprEN 1993–1-5: 2022 [1] design force. The two full-scale plate girders fail due to buckling shear. Nonlinear FEM analyses based on the test girder geometry, measured initial geometric imperfections, and the material properties from the tensile tests, show excellent agreement with the test results, with less than 5% on the maximum applied forces and related displacements. The principal membrane stresses path that triggers the failure of the web plate are investigated based on numerical results and compared with the test measurements. Contrary to the assumption of a rotated stress field model, the principal compression stress obtained in the experimental test was higher than shear buckling stress in the vicinity of the intermediate transverse stiffener. • Experimental shear behaviour of full-scale thin-walled plate girders in what concerns shear loading past ultimate loading. • Focus on intermediate transverse stiffener behaviour and shear load path. • Data acquisition techniques are resumed regarding measurements using optical extensometer and laser scanning. • Finite Element Model and Analysis were performed for the simulation of the experimental tests reported. • Obtained experimental and numerical outcomes are compared to current recommendations provided by EN1993-1-5. [ABSTRACT FROM AUTHOR]

Composite shear walls are usually employed at the bottom of super high-rise structures to resist large axial forces, bending moments, and shear forces. A lot of investigations have been carried out on composite shear walls, but there are fewer comparative studies on composite shear walls with different steel layouts. In this paper, low cyclic horizontal loading tests were carried out on conventional reinforcement concrete shear walls and composite shear walls with different steel layouts (H-section steel in boundary members and the steel plate in the shear wall web, H-section steel in boundary members and the slotted steel plate in the shear wall web, evenly arranged H-shaped steel in the wall). Comparative analyses of load-carrying capacity, failure modes, and seismic performance were conducted. The effects of different steel layouts on the seismic performance of composite shear walls were investigated. Based on the tests, the finite element method is used to further analyze the influence of the shear span ratio of the shear wall and the opening rate of the built-in slotted steel plate. • Low cyclic horizontal loading tests were carried out on conventional reinforcement concrete shear walls and composite shear walls with different steel layouts. • The effects of different steel layouts on the seismic performance of composite shear walls were investigated. • The parametric analysis of the composite shear walls with different steel layouts was conducted based on numerical simulation. [ABSTRACT FROM AUTHOR]

This research developed a robust Bayesian framework for evaluating geomaterials and soil-structure interactions involving deep excavation, utilizing Bayesian Regression and Bayesian Network methods that combined data training, validation, and updating into a cohesive framework. A methodology based on Bayesian Generalized Linear Model (a variant of Bayesian Regression) was applied to a laboratory-based case study on sustainable cementitious blends. The framework effectively used past research data to estimate design parameters even though the studies involved different mix design requirements. Then, a framework based on Gaussian Bayesian Network (a variant of Bayesian Network) incorporating Bayesian updating was applied to an established case history for deep excavation in clay. Two-dimensional finite element analysis was used to generate data for model training and updating. The GBN models accurately estimated responses such as wall deflections, wall bending moments, and ground surface settlements through a sequential updating process. The research was conducted using R programming language, with a custom R script designed to follow the process flow of the proposed framework. The successful application and validation of this framework demonstrated its potential for characterizing geomaterials and evaluating complex soil-structure interactions in deep excavation, leveraging on the availability of existing data and a reliable sequential updating process. [ABSTRACT FROM AUTHOR]

Nuclear power plant piping systems frequently encounter complex loads due to factors like internal pressure, self-weight, structural supports, and operational conditions. Within these systems, pipe bends play a crucial role in releasing energy through deformation. Cracks pose a risk to the integrity of the system, necessitating the calculation of the plastic collapse load for cracked pipe bends. This study presents estimations for the plastic collapse load of cracked pipe bends under pure out-of-plane bending moments and simultaneous in-plane and out-of-plane bending moments. Cracks located in the intrados, extrados, and crown of pipe bends were considered. The estimations for plastic collapse load are proposed based on the observed similarity between plastic collapse load and plastic deformation under both in-plane and out-of-plane bending conditions. For combined in-plane and out-of-plane bending moment conditions, circular and parabolic relationships have been proposed for a straightforward plastic collapse load prediction. Additionally, the estimations for plastic collapse loads were derived from the results of finite element analysis conducted on crack-free pipe bends, demonstrating its applicability to cracked pipe bends as well. • Plastic collapse load estimates for cracked pipe bends under combined loads, including out-of-plane bending, were studied. • Yield loci were compared with plastic collapse loads of cracked pipe bends under combined in-plane and out-of-plane bending. • Plastic collapse load estimates for crack-free and cracked pipe bends under combined in-plane and out-of-plane bending are proposed. [ABSTRACT FROM AUTHOR]

In this study, a Finite Element (FE) model of locally strengthened high-strength stainless-steel tube subjected to lateral impact loads is established using LS-DYNA to investigate its dynamic behaviours. The accuracy of the FE results is verified by comparing with the test results. The impact force, bending moment, stress and strain responses as well as the internal energy dissipation histories of the strengthened tube are analysed during the entire impact process. The results indicate that the impact resistance of the strengthened tube is obviously enhanced as compared to hollow stainless-steel tube. Furthermore, parametric studies are conducted to reveal the influence of axial compressive force, impact position, impact velocity and material strength on the impact behaviour of the strengthened tube. The results show that the application of axial compressive force reduced the impact force and increased the deformations of the strengthened tube. The impact resistance of the strengthened tube performed an increasing trend when moving the impact position towards the support and increasing the material strength. In addition, the increase of impact velocity significantly reduced the impact duration. Finally, design recommendations and process were proposed to facilitate the application of locally strengthened tube. • The impact response of locally strengthened stainless-steel tube was numerically studied. • The impact force, bending moment, stress and strain response and energy dissipation were analysed. • Concrete was found to dissipate more impact energy than the other parts. • The effects of variant parameters on impact performances of the strengthened tubes were investigated. [ABSTRACT FROM AUTHOR]

Built-up radially battened columns (RBCs), comprising several identical circular steel tubes interconnected by multiple radial-shaped battens, represent an innovative column design that combines aesthetic appeal with exceptional load-bearing capacity. This makes them well-suited for architectural applications in large public buildings such as stations and airports. The axial compressive strength design methods for the built-up RBC have been extensively explored in the authors' prior studies. However, in real-world engineering applications, built-up RBCs may experience simultaneous axial compression and varying directional bending moments, particularly when considering potential eccentric compression or wind and earthquake loads in public buildings. Currently, strength design methods for this loading condition are still lacking. To address this deficiency, this paper primarily delves into the failure mechanism and strength design methods for built-up RBCs experiencing combined axial compression and arbitrary directional bending moments. Initially, the sectional strength of the built-up RBC is investigated by using a shell finite element model (FEM) for the built-up RBC. It is revealed that the compression-bending sectional strength of the built-up RBC exhibits significant differences with varying bending directions and tube numbers. Moreover, in some bending directions, the M - N sectional strength curve of the built-up RBC exhibits convexity. By integrating theoretically derived equations grounded in the principles of materials mechanics with FEM numerical calculations, concise and practical design equations are proposed for accurately predicting the sectional strength of the built-up RBC under combined axial compression and arbitrary directional bending moments. Subsequently, The buckling strength of the built-up RBC is studied using the FEM, considering initial geometrical imperfections consistent with first-order flexural buckling and accounting for geometric nonlinearity. It is noted that the bending direction of the built-up RBC may deviate during loading. Besides, the M - N buckling strength curve of the built-up RBC is not as convex as its M - N sectional strength curve. Based on calculations from numerous examples, practical design equations for predicting the buckling strength for the built-up RBC under axial compression and any directional bending moments are introduced. The key findings of this paper contribute to the compression-bending strength design of RBCs, enriching RBC design theory and promoting the widespread application of built-up RBCs in actual engineering projects. [Display omitted] • The M - N strength of RBCs varies with different bending directions and tube numbers. • The M - N sectional strength curve of the built-up RBC is convex. • The built-up RBC's bending direction may deviate during loading. • The M - N buckling strength curve of RBCs is less convex compared to its M - N sectional strength. • The M - N strength of RBCs can be predicted by a quadratic function. [ABSTRACT FROM AUTHOR]

The bending mechanical properties of FRP-confined square concrete-filled steel tubes (CFST) reinforced with internal latticed steel angles, including the failure modes, characteristic curves and characteristic mechanical parameters of tested specimens, were investigated through experiments in this paper. The bending mechanisms were also analyzed using an established finite element model, including the analysis of the bending moment borne by each component, the distributions of contact pressure between different components at the mid-span section, and the distributions of the neutral axis under the bending capacity. The key influential parameters, including the tensile strength and thickness of the FRP, were also examined. The results indicate that the FRP has almost no influence on bending stiffness, however, it enhances the yield bending moment and bending capacity to a certain extent. It was also found that the enhancement decreases as the width of steel tube increases, and the influence of FRP is more profound before reaching the peak load. The calculation formulas for the bending capacity were developed using the superposition method and numerical fitting method. Analysis of their accuracy shows that the formulation using the superposition method yields relatively accurate and safe prediction results, with the prediction errors of less than 20 %. • The bending behavior of FRP-confined square CFST reinforced with internal latticed steel angles is investigated through experiment; • A method for characterizing the yield bending moment and bending capacity of the tested specimens is proposed; • The bending mechanisms are analyzed using an established finite element model; • The calculation formulas for the bending capacity are proposed based on the superposition method and numerical fitting method. [ABSTRACT FROM AUTHOR]

The present paper reports results of a numerical investigation of the mechanical behavior of a column base plate connection subjected to an axial compression force and a bending moment. A three-dimensional nonlinear model was developed, using the Cast3M software, and validated against experimental data. In addition, the material nonlinearity as well as contact conditions between the different components of the connection were thoughtfully considered. Based on the validated model, an extensive parametric analysis was conducted to investigate the effect of stiffeners on the forces in the anchor rods. The results clearly indicate that the design approaches that consider only the tensile strength of anchor rods while neglecting the bending moments can lead to a poor estimation of the forces applied to these rods. They also suggest that adding stiffeners provides additional strength and reduces the anchor rod bending in one direction. However, it is important to note that the stiffeners also induce an additional moment in the opposite direction. This could make the anchor rod more susceptible to biaxial bending with tension. Furthermore, this study proposes a new specific shape of stiffener is suggested (c bp5). It was concluded that the proposed shape of stiffeners allows a more uniform distribution of forces and avoids excessive stress concentrations, effectively prevents the biaxial bending in the anchor rod. [Display omitted] • 3D FE model is developed to analyze column base plate connection behavior. • Eurocode 3 overestimated anchor rod strength by neglecting bending moment. • Stiffeners induced biaxial bending on anchor bolts in stiffened connections. • Proposed stiffener shape prevented biaxial bending of anchor rods. • Compression center position influenced by the stiffeners and their shapes. [ABSTRACT FROM AUTHOR]

• Peeling forces in friction stir composite joints are not enough to overcome the binding forces. • Higher stiffness of composite joints resulted in a rigid body rotation due to secondary bending. • The failure mechanism exhibited a brittle behaviour with crack nucleation at the highly strained region. • A relationship between tension, bending and mechanical performance of the joint was obtained. • The development of secondary bending moment acts as main catalyst of the failure mechanism. Friction stir composite joints between an aluminum alloy (AA6082-T6) and reinforced polymer (NorylTM GFN2) were studied regarding their failure characteristics. A comprehensive analysis on the mechanical behaviour of the joints was carried out, assessing the resulting deformed shape, the associated strain field and the observed failure modes using a digital image correlation (DIC) system and comparing with a finite elements method (FEM) model. The numerical model evidenced a good fitness to the experimental results since both the displacements and strain fields were found to be very similar. Both numerical and experimental strain fields in the longitudinal direction exhibited a localized spot of highly strained material, clearly indicating the nucleation site. Since secondary bending occurs in structural elements under tension due to geometrical and stiffness asymmetries, as is the case of overlap composite joints, a bending stress is induced, increasing the local stress compared to the nominal tension stress values. The ultimate tensile stress of the joints was found to range between 60.2 and 70.4 MPa, leading to an average joint efficiency of 82.6 %. The bending factor (k b) at the failure region was found to be 2.0, which means that the bending stress accounts for 2/3 of the total stress, acting as main failure catalyst. [ABSTRACT FROM AUTHOR]

Concrete-filled tubular flange (CFTF) girders offer superior torsional stiffness compared to traditional I-shaped plate girders, providing enhanced flexural performance. To accurately assess the flexural capacity of CFTF girders, both flexural tests and theoretical analyses were conducted on specimens with and without concrete decks. The experimental data were meticulously analyzed to understand the flexural mechanism, yielding sequence, interface slip, strain distribution, and confinement effect of CFTF girders. Subsequently, finite element models were then utilized to analyze the influence of cross-section dimensions and material optimization on the flexural behavior of CFTF girders. Comparative analyses with I-shaped girders were also performed to highlight the structural advantages of CFTF girders. The proposed flexural calculation formulas were validated against both experimental and analytical results, demonstrating a fitting accuracy between 95 % and 98 % for the yield moment and between 96 % and 98 % for the ultimate moment. The method proposed in this paper provides a reliable and accurate approach for evaluating the flexural capacity of CFTF girders, significantly contributing to the advancement of design and analysis practices in structural engineering. • The flexural tests and theoretical analyses on concrete-filled tubular flange (CFTF) girders were conducted. • The flexural mechanism, interface slip, strain distribution, and the confinement effect are analyzed. • Finite element models are utilized to analyze the influence of cross-section dimensions and material optimization. • A calculation method for the elastic and plastic flexural behavior of CFTF girders is proposed. [ABSTRACT FROM AUTHOR]

• Previous studies have lacked comparative research on tunnel failure analysis under oblique-slip fault conditions. • Under the action of fault displacement, tunnels undergo shear and bending failures. • Oblique-slip faults cause more severe damage to tunnels, with more cracks and a wider range of damage. • The displacement mode of active faults is the key factor determining the final failure mode of tunnels. To deeply study and compare the failure characteristics of tunnels under strike-slip and oblique-slip active faults, with the engineering background of a railway tunnel in western China crossing both strike-slip and oblique-slip active faults, two sets of large-scale indoor model tests with a geometric similarity ratio of 1:35 were conducted. The fissure development patterns and strain trends of the tunnel under the movement of both types of faults were monitored and analyzed. Meanwhile, a three-dimensional model of tunnel-rock-fault interaction was established using ABAQUS finite element analysis software to determine the variation patterns of bending moments and shear forces of the tunnel under the movement of both types of faults. The results showed that under the movement of strike-slip and oblique-slip active faults, circumferential bending fissures appear at the right waist of the hanging wall and the left waist of the footwall of the tunnel, and shear oblique fissures appear at the vault of the fault fracture zone. Among them, the number of cracks, the range of tunnel cracking and the degree of crack damage under the condition of the oblique-slip fault are obviously more serious than those under the condition of the strike-slip fault. Under the dislocation of the oblique-slip fault, a large area of broken zone appears in the vault of the fault fracture zone, the lining falls off, the steel bar is exposed, and there is an obvious uplift phenomenon. The right waist of the tunnel's hanging wall mainly experiences tension while the left waist experiences compression, whereas on the hanging wall, the right waist experiences compression while the left waist experiences tension. Under the fault movement, the maximum bending moment value mainly occurs at a distance of 10 m from the fault fracture zone on both the hanging wall and the footwall, with the bending moment values at the fault fracture zone nearly approaching zero. The maximum shear force value occurs at the fault fracture zone. Under the movement of both types of faults, the failure mode of the tunnel is mainly characterized by bending failure of the hanging wall and the footwall and shear failure at the fault fracture zone. Compared to strike-slip active faults, the development of fissures in tunnels under oblique-slip active faults is more severe, with larger bending moment and shear force values, and a wider range of tunnel failure. These results can provide theoretical and technical experience for future similar projects. [ABSTRACT FROM AUTHOR]

This paper presents the Green's Functions Stiffness Method (GFSM) for solving linear elastic static problems in arbitrary axially non-uniform Timoshenko beams and frames subjected to general external loads and bending moments. The GFSM is a mesh reduction method that seamlessly integrates elements from the Stiffness Method (SM), Finite Element Method (FEM), and Green's Functions (GFs), resulting in a highly versatile methodology for structural analysis. It incorporates fundamental concepts such as stiffness matrices, shape functions, and fixed-end forces, in line with SM and FEM frameworks. Leveraging the capabilities of GFs, the method facilitates the derivation of closed-form solutions, addressing a gap in existing methods for analyzing non-uniform reticular structures which are typically limited to simple cases like single-span beams with specific axial variations and loading scenarios. The effectiveness of the GFSM is demonstrated through three practical examples, showcasing its applicability in analyzing non-uniform beams and plane frames, thereby broadening the scope of closed-form solutions for axially non-uniform Timoshenko structures. [ABSTRACT FROM AUTHOR]

This study aims at investigating the effects of local wall thinning on the cyclic plasticity behaviours of 90° back-to-back pipe bends, which are commonly utilised in flexible piping systems within plant facilities. Over time, the prolonged operation of these pipe bends may lead to wall thinning and a deterioration of their structural integrity. To understand the effects of such wall thinning, a 3D finite element analysis is conducted. Load interaction diagrams are generated using the Linear Matching Method, which considers the cyclic plasticity behaviours of shakedown and ratcheting. The investigation includes pipe bends with three different locations of local wall thinning: intrados, extrados, and crown. The pipe bends are subjected to steady internal pressure and various cyclic bending moments, including in-plane closing, in-plane opening, and out-of-plane bending. Moreover, comprehensive parametric studies are carried out for the pipe bend structures, varying the wall thinning rates. Semi-empirical formulas are derived based on the study results, enabling the prediction of limit load, shakedown limit, and ratchet limit concerning the position of the local wall thinning. Results and discussions have demonstrated the most detrimental combination of wall thinning type and loading on the structural integrity of the pipe bends and have provided valuable insights into the problems associated with deteriorated pipe bends. • The effects of local wall thinning on the cyclic plasticity behaviours of 90° back-to-back pipe bends are investigated. • The pipe bends with three different locations of local wall thinning is considered: intrados, extrados, and crown. • Shakedown and ratchet limit boundaries are analysed using the Linear Matching Method. • Critical loading combinations and the specific wall thinning locations that may lead to adverse effects are identified. [ABSTRACT FROM AUTHOR]

This study presents enhancements made to traditional aluminum alloy gusset (AAG) joints, including the integration of a central stiffening (CS) system, an inter-panel stiffening (IS) system, and a peripheral stiffening (PS) system. Three sets of tests on a full-scale specimen are conducted to investigate the improved AAG joint's axial stiffness, in-plane and out-of-plane bending stiffness, as well as ultimate load-bearing capacity. Nonlinear refined finite element models (FEMs) are established and validated through experimental results. Theoretical mechanical models are developed by integrating experiments and FEMs. These models elucidate the contribution of the stiffening systems to the joint's mechanical performance. The CS system is proven to significantly assist in load transfer, particularly in out-of-plane bending conditions. The IS system enhances overall inter-panel integrity, especially during the plastic deformation phase under out-of-plane bending moments. The PS system improves joint stiffness by participating in load transmission under both axial load and in-plane bending moments. Compared to traditional AAG joints, the combined effects of the three stiffening systems enhance overall structural integrity, stiffness, and load-bearing capacity. This enables the full utilization of component material properties and provides excellent ductility before failure occurs. • A theoretical model of an improved aluminum alloy gusset joint was developed. • FEM and mechanical model alignment were achieved, validated by full-scale tests. • Three loading phases in directions confirmed joint enhancements in mechanical model. • Stiffening systems optimized load transfer, increasing joint stiffness and capacity. [ABSTRACT FROM AUTHOR]

• The wooden drum-tower exhibits poor ductility, and the premature withdrawal of tenon-mortise joints in components adjacent to the failure zone is a triggering factor for the collapse of the structure. • After component failure, the structure undergoes internal force redistribution. The beam in the failure zone is forced to bear tension, bending, and torsion simultaneously, leading to the failure of the tenon-mortise joints. At the moment of mortise-tenon joints failure, the columns within the failure zone gradually tilt under the influence of gravity, eventually leading to progressive collapse. • The failure of mortise-tenon joints in the failure zone is characterized by compression deformation of the tenon in the transverse direction and splitting of the mortise edges. Non-collapsed structure tilts as a whole, with slight detachment of tenon heads and uplift of column bases. The drum-tower belongs to the category of towering structures, and the overall collapse is a common accident in such structures. In order to study the anti-collapse performance of drum-towers, this research used the bottom floor of a wooden drum-tower in the southwest China as a prototype, designing and producing a 1/3 scale structural model. The sudden-column-removal (SCR) method was employed to simulate the structural collapse process, observe collapse characteristics, and analyze the dynamic response of the structure. A finite element model was established, and on the basis of verifying its accuracy, a parameter expansion analysis was conducted. The study indicates that the ductility of wooden drum-towers is relatively poor, and the pulling out of mortise- tenon joints in adjacent components in the failure area is a primary factor for the progressive collapse of the structure. Due to the redistribution of internal forces, the load-bearing status of beams in the failure area changes, experiencing tension, bending moment, and torsion simultaneously, leading to the pulling out, compression, and splitting of mortise-tenon joints. After the failure of these joints, the structure undergoes progressive collapse under the influence of gravity. The dimensions of mortise-tenon joints and the friction coefficient have a significant impact on the anti-collapse performance of the structure. Larger dimensions and friction coefficients result in slower structural damage and more stable structural response. Among these factors, increasing the depth of mortise-tenon joints has the most significant effect. [ABSTRACT FROM AUTHOR]

• The impact test results of the scaled model corresponding to the finite element model were used to verify the accuracy of the adopted material models and contact relationships. • Based on the spatial complexity of urban overpasses, the dynamic responses and failure mode of the full-bridge model under non-bottom impact were numerically simulated. • Four comparative models were established to study the effect of the bridge model parameters on impact responses. Urban viaducts are likely to be subjected to non-ground-level vehicle collisions during their service life period. However, current research primarily focus on vehicle impacts on the bottom of bridge piers. In this research, a full-bridge scale model impact test was conducted to validate the accuracy of the finite element (FE) model. Then, LS-DYNA is used to establish refined vehicle-bridge collision FE models. The dynamic responses and failure mode of the pier impacted by the non-bottom vehicle are investigated. Besides, the effects of bridge structure spatial stiffness, superstructure mass, and double-column structure on the impact responses of bridges are analyzed. The results show that vehicle collisions are characterized by a continuous impact action involving multiple components. The damage to the full bridge model is concentrated in the directly impacted double-column pier, where the head-on column sustains three-point bending damage, the indirectly impacted column sustains bending damage at the top and bottom, and the cover beam sustains tensile shear damage. The non-bottom impact significantly increases displacements and bending moments of the pier while causing a substantial decrease in bottom shear. The impact responses of the pier are greatly influenced by the superstructure mass and double-column structure, while the spatial stiffness of the bridge has minimal affection. [ABSTRACT FROM AUTHOR]

Local wall-thinning of pipe is a common volume defect in application, which would cause pipeline leakage or rupture under complicated pipeline loads. The finite element analysis method was used to analyze the limit load of Pipe Bend with Local Wall-Thinning defect (PB LWT) under internal pressure, bending moment, torsion moment, axial force, and their combinations. The limit load empirical equations of PB LWT under single load and complex loads were fitted. According to the allowable pipeline load on equipment nozzles, the influences of torsion moment and axial force on the load bearing capacity of PB LWT were quantitatively analyzed. It is found that the load bearing capacity is reduced by an average of 1 % for medium and low-pressure equipment. For high-pressure equipment, the load bearing capacity is reduced by 10.07 %∼20.90 % under the influence of torsion moment. Under the effect of axial force, the load bearing capacity is reduced by 2.01 %∼12.40 %. • The limit loads of bends with extrados local wall-thinning defect are analyzed under internal pressure, bending moment, torsion moment, axial force, and their combinations. • Empirical equations for limit load of bend with defects are worked out for complex loads. • Torsion and tension can decrease the load-bearing capacity of bends by up to 10 %∼20 %. [ABSTRACT FROM AUTHOR]

The current Eurocode 3 rules for buckling of welded I-section members are based on the assumption of hot-rolled flanges. However, flame-cut flanges are widely used in practice and induce significantly different residual stress distributions, affecting the lateral-torsional buckling resistance. Experimental tests and finite element analyses considering residual stress distributions clearly highlighted the beneficial effect of flame-cut flanges compared with hot-rolled flanges on the lateral-torsional buckling resistance of welded I-beams. To complete these preliminary results, a large number of non-linear finite element analyses are performed considering welded beams made of hot-rolled or flame-cut flanges. The beams are composed of steel grades S275 and S355. Numerical results confirm the influence of the flange fabrication process on the buckling behaviour. Eurocode 3 rules are found to be overly conservative for welded beams made of flame-cut flanges. Consequently, proposals are made that are more suitable for estimates of the lateral-torsional buckling resistance of welded beams made of flame-cut flanges. The code rules are also very conservative for welded beams made of hot-rolled flanges with a medium-to-high slenderness. A design method is thus proposed to improve the prediction accuracy of the lateral-torsional buckling resistance of slender welded beams made of hot-rolled flanges. The novel design method from prEurocode 3 provides acceptable values of the buckling resistance for welded beams made of flame-cut flanges but is restricted to uniform doubly symmetric beams. An extension of its scope to mono-symmetric uniform beams as well as tapered beams is thus suggested. An enhanced imperfection factor is proposed, adapted to welded beams made of flame-cut flanges. • Design method to compute the LTB resistance of welded beams with flame-cut flanges using the Eurocode 3 buckling curves. • Design method to compute the LTB resistance of welded beams depending on their geometry, flange fabrication process and bending moment distribution. • Adaptation of the new verification format of prEN 1993–1-1 for lateral-torsional buckling to tapered and/or mono-symmetric beams. [ABSTRACT FROM AUTHOR]

In this study, the buckling behavior of cold-formed beam-column members with sigma and lipped channel sections under the combined effect of axial load and biaxial bending moment (P-M x -M y) was compared. A total of 30 specimens (15 with sigma sections and 15 with lipped channel sections), each measuring 1500 mm in length, were tested under monotonic loading. The performances of the specimens under eccentric loading such as strength and energy absorption capacity were investigated experimentally and numerically. The local, distortional and global buckling modes that determine the bearing capacity of the section and the length of the sigma and lipped channel member where all these buckling modes can be seen were determined. Finite element analysis (FEA) was performed with Abaqus software, and the numerical results were verified against experimental results. Using the validated finite element model, a comprehensive parametric study was carried out by performing 2894 FEA on sigma and lipped channel section members with various cross-sectional dimensions and lengths. Experimental results show that there are significant differences in load bearing capacity, energy absorption capacity and buckling modes of sigma and lipped channel section members. In the FEA/ AISI-S100 code comparison made at the end of the parametric study, it was determined that differences occurred according to the lengths, cross-sectional properties and loading points of the members. It was determined that the error rate was safer when the lips were subjected to tensile stresses than when they were subjected to compressive stresses. Finally, it was determined that the FEA/AISI-S100 error rate decreased as the length of the sigma-section members increased. • The experimental behavior of sigma and lipped channel sections was investigated under the combined actions of axial load and biaxial bending. • The buckling behavior of sections was determined through a comprehensive parametric study. • The experimental and numerical results were discussed. • Results were compared with AISI-S100 standard. [ABSTRACT FROM AUTHOR]

Reported studies on T-head Square-neck One-side Bolts (TSOBs) bolted I-beam to Hollow Section Square Column (HSSC) connections demonstrated the potential of TSOB applications in terms of mechanical properties, installation construction, and cost savings [11–14]. However, existing research was limited to the connection tests and lack a systematic and complete design approach. In this paper, the method for predicting the bending moment capacities and failure modes of the connections was proposed based on the existing test researches. Besides, the Finite Element Model (FEM) of the connections was established and validated by the reported test results. A sensitive analysis on the geometric parameters of the plastic hinge line pattern for calculating the bending moment capacity of the HSSC connecting face was carried out by the validated FEM. The proposed method was compared with the numerical simulation method in terms of the predicted results of the connection structural behavior. The results show that the prediction method proposed in this paper for the connection bending moment capacities and failure modes is accurate and reliable. Moreover, the mixed patterns of Type-H bolt holes and Type-V bolt holes are recommended for the TSOBC design because of the higher bending moment capacity than the unitary bolt hole patterns. • Method for predicting the bending moment capacity of TSOBC was proposed. • Failure mode of TSOBC was predicted based on design information. • Mixed patterns of Type-H and Type-V bolt holes are recommended for TSOBC. [ABSTRACT FROM AUTHOR]

Round-ended concrete-filled steel tubular (RECFST) columns are gaining increasing usage in bridge structures. During their service life, RECFST columns under eccentric compression may suffer from impact loading. This study conducted test and numerical investigations to assess the performance of RECFST columns under the coupled actions of compression, bending and lateral impact loads. Fourteen columns were fabricated and tested, considering the influences of axial-load ratio, bending moment and impact energy. The damage mode and the time histories of impact force and displacement were accessed and analyzed. The experimental findings revealed that the initial bending moment negatively affected the impact resistance of RECFSTs. In addition, finite element model was established in ABAQUS and calibrated against the test results. The calibrated model was then employed to conduct the failure mechanism analysis and parametric study. Finally, a single-degree-of-freedom (SDOF) analysis was conducted to predict the mid-height deflection of RECFST columns under combined action of compression, bending and lateral impact loads, by incorporating the influences of pre-axial load and initial bending moment. • Drop-hammer impact tests on RECFST columns with varying eccentric compression. • Coupling influence of compression, bending and lateral impact loads. • Prediction of mid-height deflection response using the SDOF method. [ABSTRACT FROM AUTHOR]

Based on the zig-zag theoretical model of corrugated steel web beam (CSW), the governing equations in the form of state equations are derived and their analytical solutions are obtained for different loads, variable cross-sections and boundary conditions. Through numerical examples, it is verified that the bending moment, deflection and stresses predicted by the present analytical method have a good agreement with the results of the three-dimensional finite element model. The applicability of the present method for non-prismatic continuous beams with CSWs under different loads is also demonstrated. Meanwhile, it is found that the quasi-plane assumption is still valid in non-prismatic continuous beams with CSWs. Through quantitative analysis of the flexural stresses in the top and bottom slabs, it is confirmed that the zig-zag theory in this study can well reflect the accordion effect of CSWs. Because of the inclined bottom slabs in the non-prismatic beams with CSWs, the Resal effect on the shear stresses in the CSWs and bottom slabs, which is caused by the vertical component of the axial force in the bottom slab, is discussed. A refined shear formulation is developed for more accurate shear stresses in the CSWs and bottom slabs, which provides fundamental theoretical support for the strength prediction of the non-prismatic beam with CSWs. • The zig-zag theory is developed for the non-prismatic beams with CSWs based on the state space method. • The quasi-plane assumption is still valid in non-prismatic continuous beams with CSWs. • The refined shear formula considering Resal effects is derived for the CSW beam with inclined bottom slab. [ABSTRACT FROM AUTHOR]

This paper presented a series of tests to investigate the behaviour of the extended end-plate connection utilizing high strength Q960 steel. A total of 8 specimens were tested, including two under ambient temperature and three under high temperature. The results of the tests indicated that increasing the end-plate thickness from 8 mm to 12 mm significantly enhances the flexural capacity and initial rotational stiffness of the connections but reduces the critical temperature and ultimate rotation. In addition, a higher beam bending moment ratio was found to increase the ultimate rotation of the connections while having minimal impact on the critical temperature. Then, the finite element model of the connections was established to investigate the parametric effect, including column axial pressure ratio, beam bending moment ratio, and end-plate thickness on fire resistance. The numerical analysis indicated that increased column axial pressure ratio and end-plate thickness decreased fire endurance, critical temperature, and ultimate rotation of the connections. On the other hand, increasing the beam-bending moment ratio enhanced the ultimate rotation of the connections. Lastly, a rotation-temperature relationship model was proposed to accurately predict the temperature-rotation curve of high-strength steel Q960 end-plate connections, which was validated with experimental data. • Fire tests on response of high strength Q960 steel connections were carried out. • Numerical models were developed to simulate the behaviour of Q960 teel connections at elevated temperatures. • Parametric studies were performed to investigate the effect of key factors on fire resistance of the connections. • A rotation-temperature relationship model was proposed to predict the fire behaviour of Q960 steel connections. [ABSTRACT FROM AUTHOR]

In this paper, a pinned scaffolding node is proposed and studied with Q355 steel and sorbite stainless steel. Twelve sets of forward and reverse bending tests were designed to study the bi-directional bending performance at temperatures of +20 °C, −20 °C, and − 40 °C. The test results show that as the temperature decreases, the initial rotational stiffness and bearing capacity of the QSJ and the SSSJ both increase. Under the same temperature conditions, the yield bearing capacity and maximum bearing capacity of the SSSJ are greater than those of the QSJ. However, the SSSJ is susceptible to cracking in the weak zone of the C-shaped member subjected to forward bending moments in low-temperature environments, which requires attention in design and use. A finite element model can accurately simulate the bi-directional bending performance of the joint. The results show that increasing the thickness of the U-shaped members by 1–1.5 mm significantly increases the maximum load capacity of the joint. The wall thickness of the pipe has no influence on the bending properties of the joint, but the initial stiffness of the joint can be increased by the depth of wedging, a wall thickness of 6 mm is recommended for C-members. The form of damage to the SSSJ can be improved by increasing the curvature of the upper edge of the C-member at the wedge. The results of this paper can provide methods and references for the engineering design of scaffolding as well as for testing in low-temperature environments. • This paper adopts the separated low temperature loading device, which is convenient for the installation and disassembly. • This study presents a low-temperature loading test device and method. It can provide a test environment of −70 °C ∼ 150 °C. • It's innovative to study the material properties of cable body stainless steel and Q355 at −40 °C, −20 °C and room temperature. • The mechanical properties of the pin-type scaffolding nodes using sorbite stainless steel and Q355 at low temperature were investigated. [ABSTRACT FROM AUTHOR]

This paper investigates experimentally and numerically the behaviour of a balcony-to-slab connection made by an H-profile embedded in the concrete slab. A large-scale test was performed on a specimen of the connection system in order to determine the moment-bearing capacity, the deformation behaviour, the cracking patterns, the distribution of the bending moment along the axis of the embedded steel H-profile as well as the failure mode of the connection system. The test results showed that the failure mode was governed by the concrete shear of the slab. In addition, a 3D finite element model of the experimental test was also carried out and successfully validated against the experimental results. For a practical design of the connection system, a model based on Timoshenko beam on elastic foundation (BEF) was investigated and verified against the results obtained from the validated FE model. The Winkler modulus of the BEF model was determined by considering the local deformation of the concrete based on a strut-and-tie model. The results demonstrate that the BEF model with this value of the Winkler modulus provides a conservative estimation of the shear and bending forces applied to both the embedded H-profile and the concrete cross-sections. This method is a first tentative design basis using linear elastic theory for such a system. • Experimental and numerical investigation on the behaviour of embedded H-profile balcony-to-slab connection • A BEF model is proposed to determine the distribution of shear and bending forces on embedded steel profile and concrete. • Winkler modulus is determined by considering the local deformation of the concrete based on a strut-and-tie model. [ABSTRACT FROM AUTHOR]

With the increasing demand for underground transport infrastructures in urban areas, and associated hazards during the construction of these complex structures characterized with a number of uncertainties, there is an acute need for the development of methods and tools that enable efficient and accurate exploration of the design options to minimize risks induced to the environment. Mechanized tunneling, although it requires high initial investments compared to other tunneling methods, offers a safe and productive way to construct urban tunnels. In the mechanized tunneling process, the lining plays a critical role to provide the support for internal structures, i.e roads, facilities. At the same time, it helps stabilize the ground condition. Together with the jacking system, the lining provides the mean to thrust the tunnel shield (TBM) during excavation. In this work, we address the problem of effective modeling and simulation of the tunnel lining segment. The objective is to demonstrate a systematic and versatile approach to analyze the tunnel lining in different practical scenarios. In terms of modeling, a BIM-based approach is used, which connects the user-friendly software interface used in daily engineering practice with effective simulation tools. The proposed approach utilizes high-order definition of geometry in the design model as well as parametric model definitions to reconstruct the corresponding high-order numerical models. This results in a high-accuracy and computationally low-cost model to analyze a complex structure including an interaction with the soil based on a nonlinear surface springs model. In addition, it allows to analyze the stress and bending moment in the lining segment with high accuracy. The numerical results show that negligible modeling efforts and a reduced computational time up to ten times for given accuracy are achieved. • Isogeometric Analysis is used for tunnel lining deformation and bending moment analysis. • The geometry of the lining is reconstructed from the BIM-based design software. • The time-to-accuracy analysis is superior to traditional finite element analysis. [ABSTRACT FROM AUTHOR]

Offshore wind turbines (OWTs) are affected by wind, wave, and current during their service life, which lead to the substructures undergoing combined effects of complex lateral loads and local scour. This phenomenon poses a significant challenge to the bearing capacity and cyclic responses of the widely used rigid monopiles for OWTs. This study develops three-dimensional numerical model to investigate the behavior of a rigid monopile subjected to lateral monotonic and cyclic loads, considering the stress history alteration induced by local scour. The hysteresis and plasticity accumulation of soils are captured by a bounding surface model. An accurate and concise semi-implicit stress integration scheme is creatively proposed to effectively incorporate this advanced constitutive model into the finite element (FE) software. The numerical model is verified by comparing FE results with centrifuge test results. Subsequently, the key factors such as cumulative deformation characteristics and bending moments distribution are investigated under different scour and cyclic loading conditions. The results indicate that with the facilitation of proposed semi-implicit scheme, the bounding surface model is capable of capturing the deformation pattern and cumulative deformation behavior of laterally loaded rigid monopile, and the cyclic responses of the monopile are significantly affected by the local scour. [ABSTRACT FROM AUTHOR]

• The nonuniform fault displacement, fault zone width, and nonlinear soil-tunnel interaction are considered in this model. • This model agrees well with the numerical results, the error of bending moment is 0.8%, and the error of shear force is 4.6%. • The effect of fault displacement, fault zone width, and the maximum fault displacement ratio on tunnel response are analyzed. • The failure evolution process of the tunnel under reverse fault dislocation is revealed in detail. Tunnels subjected to reverse fault dislocation undergo severe structural damage, and their mechanical response and failure characteristics play a key role in seismic fortification efforts. This paper investigates the mechanical responses and failure characteristics exhibited by tunnels subjected to reverse faulting using theoretical analysis and numerical simulations. A theoretical model is established for analysing the bending moment, shear force, and safety factor of the tunnels under reverse fault dislocation. The nonuniform fault displacement, fault zone width, and nonlinear soil-tunnel interaction is applied in the proposed theoretical model, significantly improving the analysis accuracy and range of applicability. The corresponding numerical simulation based on the XFEM (extended finite element method) is carried out, and the proposed theoretical model is verified by the numerical results. The theoretical results demonstrate excellent agreement with the numerical results when nonuniform fault displacement is considered. A parametric analysis is presented in which the effects of the maximum fault displacement, fault zone width, and ratio of the maximum fault displacement of the footwall to the hanging wall are investigated. The results show that the ultimate fault displacement for compression-bending failure of the tunnel subjected to reverse fault dislocation is estimated to be approximately 30 cm, while the ultimate displacement for shear failure stands at 20 cm. Variations in the fault displacement ratio yield alterations in the distribution pattern and peak values of internal forces, together with shifts in the potential failure ranges of the footwall and hanging wall. Additionally, an initial crack emerged on the tunnel crown near the fault plane, followed by a second crack on the tunnel invert. Upon reaching a fault displacement of approximately 40 cm, the crack fully traverses the entire tunnel lining. [ABSTRACT FROM AUTHOR]

Composite pressure vessels are strategic for the present and future of the aerospace, transportation, and energy industries. These shell structures are utilized to store and transport liquids and gases and are principally composed of a cylindrical shell and two elliptical heads. The current rules for the structural design of composite pressure vessels make use of the membrane theory that excludes the bending of the structure. Nevertheless, the cylindrical shell and the elliptical heads present different curvature radii. These changes generate a localized bending deformation that determines an increase in the stress state as an effect of a local bending moment and shear force distributions that arise in the geometric transition zone. The stresses related to the bending effects die out rapidly, moving away from the junction plane, but they are sensibly higher than the membrane stress and, therefore, cannot be neglected in the mechanical assessment. Here, a closed-form analytical solution for the bending theory of composite shells is proposed. It can assist in the design of composite pressure vessels and drive the design towards reliable configurations for structural integrity. Using the Donnell–Mustari–Vlasov theory for thin-walled composite shells, the governing fourth-order differential equation is deduced and solved to obtain the displacements and stresses acting in the junction. The analytical results are successfully compared with those of reference finite element models for validation; their accuracy is proved considering different thicknesses, lay-ups, and flattening factors of the vessel [ABSTRACT FROM AUTHOR]

• Solution to cross-anisotropic viscoelastic saturated soils is derived based on the Merchant model. • Solution for a slowly changing load is taken as the kernel function for the BEM of the soils. • The Mindlin plate model is established by 8-node isoparametric finite element method. • Interaction solution of the problem is proposed using the BEM-FEM coupling and substructure technique. • Influence parameters on the time-dependent behavior of the raft are investigated. By introducing the elastic-viscoelastic correspondence principle and the integral transform technique, the extended precise integral solution to Biot's consolidation equation is derived for cross-anisotropic viscoelastic saturated soils based on the Merchant model. A displacement-time solution for a slowly changing load is obtained based on the above solution in the Laplace transformed domain, which is taken as the kernel function for the boundary element method (BEM). The Mindlin plate model is established by 8-node isoparametric finite element method (FEM), and the substructure condensation technique is employed to couple the stiffness matrices of the superstructure and the plate. With the BEM-FEM coupling method, a semi-analytical and semi-numerical solution is proposed for the interaction between layered cross-anisotropic viscoelastic saturated soils and raft foundation considering the stiffness contributions of the superstructure. Numerical examples are performed to study the influences of viscoelastic parameters, cross-anisotropic parameters, raft thickness and superstructure stiffness on the time-dependent behavior of the settlement and bending moment for the raft. [ABSTRACT FROM AUTHOR]

• An exact solution presented for rectangular plates with arbitrary varying thickness. • There is no simplifying assumption and applicable to plates with any thickness ratio. • The solution is provided for isotropic and transversely isotropic plates. • Response of graphite epoxy, E-glass epoxy, zinc, magnesium and steel plates are compared. • Varying thickness shifts the position of the maximum deflection toward the thinner edge. In this study, the bending solution of simply supported transversely isotropic thick rectangular plates with thickness variations is provided using displacement potential functions. To achieve this purpose, governing partial differential equations in terms of displacements are obtained as the quadratic and fourth order. Then, the governing equations are solved using the separation of variables method satisfying exact boundary conditions. The advantage of the purposed method is that there is no limitation on the thickness of the plate or the way the plate thickness is being varied. No simplifying assumption in the analysis process leads to the applicability and reliability of the present method to plates with any arbitrarily chosen thickness. In order to confirm the accuracy of the proposed solution, the obtained results are compared with existing published analytical works for thin variable thickness and thick constant thickness plate. Also, due to the lack of analytical research on thick plates with variable thickness, the obtained results are verified using the finite element method which shows excellent agreement. The results show that the maximum displacement of the plates with variable thickness is moved from the center toward the thinner plate edge. In addition, results exhibit the profound effects of both thickness and aspect ratio on stress distribution along the thickness of the plate. Results also show that varying thickness has not a profound impact on bending and twisting moments in transversely isotropic plates. Five different materials consist of four transversely isotropic and one isotropic, as a special case, are considered in this paper, which it is shown that the material properties have a more considerable impact on higher thickness plate. [ABSTRACT FROM AUTHOR]

The application of carbon nanotubes (CNTs) to improve postbuckling characteristics of T-section nanocomposite strut is the subject of this research. A solution procedure according to the layerwise theory along with the first-order shear deformation theory (FSDT) by taking into account the von Karman geometrical nonlinearity is proposed. Nonlinear governing equations are developed in regard to the minimum total potential energy principle, and solved by the aid of the Rayleigh–Ritz method in conjunction with Newton–Raphson method. A comprehensive parametric study is conducted to provide an insight into effects of CNT volume fraction and dispersion, geometrical parameters and boundary conditions on the bifurcation points and paths, in-plane displacement, normal stress and strain, and bending moment of T-section nanocomposite struts. A three dimensional finite element analysis using the ABAQUS commercial software is carried out to verify the obtained results, which shows close agreement. Results indicate that dispersion of CNTs plays a dominant role in bifurcation behavior of nanocomposite struts. The results also show that volume fraction of CNTs has a significant effect on the load-carrying capacity of open section nanocomposite struts. The results of this research shed light into using ultra-high-strength and light-weight open section nanocomposite struts for civil and aerospace applications. • Buckling strength of nanocomposite strut can be increased by proper CNT distribution. • Bending moment at junction of web and flange shows very complex behavior. • Distribution of the stress and strain strongly depends on the CNT dispersion. • Proposed methodology is effective in reducing computational costs and storage requirements. [ABSTRACT FROM AUTHOR]

This paper presents an evaluation of the design rules for the bending moment–shear force (M − V) interaction of cold- and hot-formed square, and rectangular hollow steel sections (SHS & RHS). More specifically, the design rules, as provided by EN1993-1-1 regarding RHS and SHS of section class 1 and 2 are covered for the steel grades S235 up to and including S460. A 4-point bending test was simulated by means of a finite element model, which was validated on the basis of experimental tests from existing literature. A parametric study was performed and numerical M − V interaction results were compared to the provisions in EN1993-1-1. This comparison indicates that the current design rules in EN1993-1-1 regarding M − V interaction are conservative and overestimate the reduction of the bending resistance due to the presence of shear. Alternative design rules for the shear area and M − V interaction of RHS and SHS are proposed and evaluated by means of a statistical assessment procedure based on existing literature and EN1990-1-1. Both newly developed design rules are shown to ensure an adequate reliability level when a partial safety factor equal to 1 is used. • Evaluation of the design rules for the M − V interaction of RHS and SHS. • An alternative design rule is proposed. • The proposed shear area matches the numerical results for all tested sections. [ABSTRACT FROM AUTHOR]

The assembling rivet-fastened rectangular hollow flange beam (ARHFB) is a new type of cold-formed steel beam. The ARHFB section has two rectangular hollow flanges formed by U-shaped and C-shaped components that connected by self-locking rivets. A finite element model is developed to simulate 16 four-point bending experiments. Details of the modeling including finite element meshing, loading and boundary conditions, contact and analysis methods are presented. The accuracy of the developed finite element model is verified by comparing the ultimate moment capacity, applied load versus deflection curves, bending moment versus deflection curves, strain versus deflection curves and failure modes obtained from the tests and the finite element analysis. Based on the validated finite element model, a parametric analysis is carried out to discuss the effects of rivet spacing, section depth, flange thickness, and web thickness on the bending performance of ARHFB. The moment capacities of these sections obtained from the parametric study are compared with predictions from Australia and New Zealand, Chinese design standards for cold-rolled sections and the DSM (Direct Strength Method). It is found that GB50018 can conservatively predict the bearing capacity of ARHFB with a large error, while AS / NZS 4600 and DSM (Direct Strength Method) cannot provide reliable prediction results. • A novel assembling rivet-fastened rectangular hollow flange beam (ARHFB) is analyzed in finite element model. • An extensive parametric investigation using a verified finite element model is conducted. • The feasibility of current design codes for ARHFBs is evaluated and judged. [ABSTRACT FROM AUTHOR]

This study presents experimental and numerical research on the dynamic behaviors and resistances of square concrete-filled steel tubular members internally strengthened by I-shaped CFRP profile (SCFST-CFRP) with fixed boundary conditions subjected to lateral impact loads. Dynamic impact tests were conducted on five SCFST-CFRP specimens and a traditional concrete-filled steel tubular (SCFST) specimen, examining their dynamic responses with respect to deformation modes, impact force, displacement, and strain distribution at different levels of impact energies and impact momentums. The test results indicated that the deformation of the specimens was concentrated in the impact region, approximately 0.38 L above the base, due to the transient localized characteristics of the lateral impact load. In terms of displacement and impact force, the SCFST-CFRP member exhibited better impact resistance compared to the SCFST member. Finite element models of the SCFST-CFRP members were created using LS-DYNA and validated against the impact tests. These validated models were then utilized to explore the damage patterns, dynamic bending moment, and load transfer mechanism of the SCFST-CFRP member under lateral impact loading. Additionally, a parametric study was conducted to evaluate the effects of load and structural parameters, including CFRP profile, impact energy, and impact momentum, on the impact resistance and dynamic flexural capacity of the SCFST-CFRP member. The results demonstrate that the enhancement in impact resistance caused by the inner CFRP profile was more significant under higher impact energy. Based on the parametric analysis results, empirical equations were proposed to predict the dynamic flexural capacity of lateral impact-loaded SCFST-CFRP members. • Impact tests of CFST member strengthened with CFRP profile under fixed boundaries. • Evolutions and distributions of deformation and internal force were summarized. • Impact load transfer mechanisms of the composite member were revealed. • Effects of load and structural parameters on the impact resistance were evaluated. • An equation for the dynamic flexural capacity of the composite member was proposed. [ABSTRACT FROM AUTHOR]

This paper presents a novel mechanical model for seismic response analysis of vertical shafts. The model is based on elastic foundation beam theory and simplifies the shaft linings as parallel Euler Bernoulli beams. Their interaction is simulated using uniformly distributed springs. The governing differential equation for shaft vibration is derived for SH wave excitation. The seismic input motion is applied to the primary lining by converting the free field displacement into harmonic form. The closed-form solutions for seismic response of both primary and secondary linings are obtained via the transfer function method. The accuracy of analytical solution is validated by comparing with finite element analysis results. Additionally, the impact of foundation stiffness, secondary lining thickness, shaft outer diameter, and relative stiffness between linings on seismic response are investigated in the parametric analysis. The analytical solutions of the seismic response analysis of vertical shafts indicates that the relative stiffness between linings significantly affects the secondary lining's peak bending moment. Furthermore, higher stiffness of the elastic connection layer between the two linings can effectively reduce the peak displacement response of the secondary lining. [ABSTRACT FROM AUTHOR]

Over the past decade, the previous hysteretic recognition of the fire threat to bridges has provoked significant progress in understanding the fire performance of bridges. However, despite the growing maritime shipment of combustibles, scarce studies have contributed to evaluating the safety of steel cable-stayed bridges subjected to under-girder ship fires. Limited existing knowledge is still based upon the less precise temperature curve method and flame geometry modeling. This study developed an advanced numerical method to more accurately evaluate the response of steel cable-stayed bridges subjected to ship fires. First, the computational fluid dynamics (CFD) approach was used to reproduce realistic fire conditions. An efficient thermal boundary, adiabatic surface temperature, was then transferred to the thermal finite element model of affected girder segments for calculating the temperature propagation. Lastly, this paper used the multiscale structural finite element method to incorporate the local performance variation of exposed girders into the response of the entire bridge. The proposed method was validated by predicting a thermomechanical response of the steel beam exposed to realistic underneath fires, agreeing well with the data from two large-scale structural fire experiments by NIST. Based on the method, the response of a typical steel cable-stayed bridge subjected to ship fires was simulated. Results show that fires can introduce local damage to the girder segments above the fire and alter the internal force distribution of the entire bridge. The bending moment of the girder sections over the fire significantly increases, and the flexural characteristic of pylons is also altered. Both thermal convection and radiation contribute to the temperature increment, and the latter dominates at the locations above fires. Adopting temperature curves can overestimate or underestimate the fire impact, introducing uncertainties to the safety of steel cable-stayed bridges in ship fires and can cause unrealistic stress concentration on the border of heated and unheated domains of exposed floors. The developed advanced method is more competent in capturing the inhomogeneous temperature and stress distribution. • CFD fire models were coupled with FEM for steel cable-stayed bridges in ship fires. • Thermal radiation governs the heat absorbed by the girder floor exposed to ship fires. • Temperatures of the girder floor propagate from the central region to the periphery. • Ship fires bring local damage to the girder and alter the entire structural behavior. • CFD-FEM method is more competent than traditional temperature-curve methods. [ABSTRACT FROM AUTHOR]

Thanks to the axial resisting contribution, inclined screw connections offer a mechanical advantage over connections with purely transversely loaded fasteners. However, the strong coupling between the axial and the transversal behaviour of the screw makes it challenging to predict the actual connection behaviour. Moreover, the presence of polyurethane interlayers for soundproofing or OSB interlayers of light-frame buildings between main members may increase the bending moment component interacting with the axial force in the screw, thus reducing the connection failure load. This paper experimentally assesses the behaviour of steel-to-timber connections, and a parametric finite element model of Winkler non-linear beam is presented and validated. Finally, a simplified analytical model for capacity prediction is presented. The results of the approach currently provided by the Eurocode 5, of an additive model and the proposed analytical model, are then compared with the results of 500 finite element analysis. • Timber-to-steel connections with soundproofing and OSB interlayers are tested. • Interlayers reduce slip modulus more than strength. • Non-linear beam on foundation model is suitable for screws connections. • Bending moment interacts with axial force reducing the connection capacity. • An elementary capacity model is validated on 500 finite elements analysis results. [ABSTRACT FROM AUTHOR]

Non-uniform elements, such as non-prismatic and those made from composite materials, are commonly used in structures. This is because the variation in their internal forces makes uniform elements less effective to withstand the external loads. This paper presents the formulation of the Green's Functions Stiffness Method (GFSM) for the static analysis of non-uniform Euler–Bernoulli frames subjected to arbitrary external loads and bending moments. The GFSM is a mesh reduction method that combines the strengths of the Stiffness Method (SM) and the Finite Element Method (FEM) with those of Green's functions, resulting in an analytic method for obtaining closed-form solutions of reticular structures. As a particular case, the GFSM is closely related to the Transcendental Finite Element Method (TFEM), which allows to obtain closed-form solutions from an implementation of the latter by only making changes at the post-processing stage. Two examples are provided with the analysis of a beam and a plane frame. Additionally, two appendices are included with the particularization of the GFSM for some specific non-uniform elements, and general stepped elements. • Closed-form solution of non-uniform Euler–Bernoulli frames. • New numerical method closely related to the Finite Element Method. • Decomposition of the structural response as a homogeneous and a fixed one. • The fixed response is obtained using Green's functions of fixed elements. • Closed-form solutions for arbitrary external forces and bending moments. [ABSTRACT FROM AUTHOR]

This work aims to solve the problem that plastic instability occurs in large-scale flat ring rolling and the geometry accuracy is hard to control due to the bending moment in the radial deformation zone exceeds its ultimate bending moment, i.e. the plastic bending moment. An analytical calculation model is put forward to design the feed strategy in large-scale ring rolling process to avoid ring plastic instability. In this analytical model, the effects of ring diameter revolution, cross-section shape variation including thickness and end surface on ring plastic instability are considered, and finally are combined in an optimized stiffness condition. The radial-axial feed coordinated strategy for a large-scale flat ring with 5 m diameter deduced from the analytical model was submitted to finite element method (FEM) simulation. The shape of the ring cross-section in the deformation zone, the variation of the ring diameter and the rolling force obtained by the analytical model and the numerical simulation are compared to verify the accuracy of the analytical model. Numerical simulations and trial production have shown that this coordinated feed strategy can avoid plastic instability in ring rolling, which effectively improves the geometry accuracy of rolled ring in large-scale ring rolling. This study is valuable for achieving low cost and high accuracy in rolling of large-scale ring. [ABSTRACT FROM AUTHOR]

• The ultimate strength of a tubular structure subjected to a bending moment is analysed. • Three specimens are designed for the experimental test. • The moment-curvature and the stress-strain relationship of the tested specimens are studied. • The tested specimens are also evaluated based on the finite element method. • The results of the finite element analysis and the experiments are compared and discussed. The objective of the present work is to analyse the ultimate strength of a tubular structure subjected to a bending moment. The tubular monopile structures are experimentally tested as well as the nonlinear finite element analysis is performed. Three specimens are designed for the experimental test by taking into consideration the typical ranges of the monopile support structures used in offshore wind turbines. The moment-curvature and the stress-strain relationship of the tested specimens are studied. The tested specimens are also evaluated numerically based on the finite element method employing a nonlinear FE analysis. The finite element analysis accounts for the nonlinearities associated with the geometry and material. The geometrical imperfections are introduced to the structure together with the initial stress arisen in the process of fabrication. The results obtained from the finite element analysis and the experimental tests are compared to each other and discussed. [ABSTRACT FROM AUTHOR]

Plate-reinforced composite (PRC) coupling beams are manufactured by embedding a vertical steel plate into conventionally reinforced concrete coupling beams to enhance their strength and ductility. This study presents a series of quasi-static tests conducted to examine the seismic behavior of PRC coupling beams and provide a scientific basis for the analysis of the shear bearing capacity of PRC coupling beams. The experimental results of seven PRC coupling beam specimens with low span-to-depth ratio tested under reversed cyclic loading are discussed. Particle image velocimetry technology is used to accurately measure the deformation performance of PRC coupling beams. The influence of span-to-depth ratio, sectional steel plate ratio, and the slab on the seismic behaviors of specimens were investigated. The experimental results indicate that, compared with PRC coupling beams without slab, PRC coupling beams with slab can increase horizontal cracking displacement and significantly improve the shear capacity and energy dissipation capacity of PRC coupling beams without slab. Embedded steel plates can improve the limited values of the shear compression ratio of coupling beams. Nonlinear finite element analysis was also carried out to model the PRC coupling beams. The numerical results indicate that the tension-softening property of concrete was more accurately simulated by the stress-crack width relationship of concrete. The internal force distribution of concrete stress, steel plate shear force, bending moment, and axial force of PRC coupling beams with low span-to-depth ratios were further analyzed. This study will benefit engineers designing PRC coupling beams. • The limited values of the shear compression ratio of coupling beams were significantly improved. • Particle image velocimetry technology is used to accurately measure the deformation performance of PRC coupling beams. • The PRC coupling beam with slab has a greater energy dissipation capacity. • The steel plate along the beam span was under tension, and the distribution of the tension is in M-mode. [ABSTRACT FROM AUTHOR]

Highlights • Effects of axial force and bending moment on the burst pressure of corroded pipelines are studied. • Burst pressure is significantly reduced under compressive axial force and closing bending moment. • Developed failure loci considering axial forces, bending moments and internal pressures. • The failure loci are found to depends on corrosion depths and load combinations. • The failure loci can be used for burst pressures assessment with known axial force and bending moment. Abstract The remaining strength of corroded pipeline is generally assessed considering the internal pressure only. However, pipelines are often subjected to axial forces and bending moments due to external loadings, which may significantly reduce the burst pressure of the pipeline. This paper presents a study using finite element analysis on the effects of axial forces and bending moments to the burst pressures of corroded pipelines. It is revealed that the compressive axial force and the closing bending moment, causing compression in the corroded area, affect the burst pressure most significantly. Considering the axial compression and closing bending moment, failure loci of combined bending moments and internal pressures are developed for different axial forces. The developed failure loci can be used for assessing the burst pressure of corroded pipelines subjected to axial forces and bending moments. [ABSTRACT FROM AUTHOR]

Abstract A high-fill slope located in Zhenxiong County, Yunnan Province, China, was designed for building placement on its top platform. A reinforcement system consisting of a geogrid, front stability piles (FSPs), retaining sheets, prestressed anchors, and rear deeply buried piles (DBPs) has been used to stabilize the slope. Two typical slope sections were selected to study the high-fill slope stability and retaining mechanism of the reinforcement system. Field measurements of the horizontal displacement and strain in the piles, as well as the anchor working load, were collected and analyzed. In addition, a series of two-dimensional finite element method (FEM) analyses combined with a strength reduction technique was conducted to analyze two selected cross sections. The results show that the retaining structure behavior is closely related to the fill construction process of a high-fill slope. The deflection of the stabilizing pile increases almost linearly with the filling height in the initial stage of fill construction. The variation in the working load of the prestressed anchor shows an offset between prestress loss and increasing fill pressure. The FEM results can provide insight into the pile-soil interaction mechanism and its contribution to fill slope stabilization. The FSPs shift the sliding surface from through the slope toe to through the top of the FSPs. The anchors can reduce the bending moment by supplying additional bearing points. The DBPs can share a portion of the sliding thrust and effectively enhance the safety factor. This paper provides a reference for reinforcement system design for similar engineering projects considering high-fill slopes. Highlights • A case of reinforcement and monitoring for a high-fill slope is presented. • The reinforcement system includes two rows of piles, retaining sheets and anchors. • The behavior of the reinforcement system is investigated through field measurements. • The reinforcement mechanism is analyzed by FEM combined with monitoring. • This study provides a reference for the design of similar high-fill slopes. [ABSTRACT FROM AUTHOR]