Search

The control techniques in buildings contribute significantly to thermal comfort and indoor air quality (IAQ). However, the gaps are existing for multitarget controls considering both thermal comfort and IAQ. They are: (1) both experimental and modeling control studies were conducted for thermal comfort, focusing on temperature and humidity. (2) All three (physical, grey-box, black-box) modeling approaches were investigated for temperature control. (3) Physical and grey-box modeling approach were adopted for humidity control. (4) physical models were developed for VOCs and CO2 control. (5) grey-box and black-box models were lacking for VOCs and CO2. (6) Multi-target controls were lacking for temperature, humidity and CO2s. (7) Limited studies are available for multi-target controls for temperature, humidity, and VOCs. (8) Multi-target controls are not available yet for temperature, humidity, VOCs, and CO2.

2,2,4,4-Tetramethyl-1,3-cyclobutanediol (TMCD) is a diol monomer for terephthalic acid (TPA) class of copolyesters that can increase the glass transition temperature and mechanical strength in comparison to conventional TPA polyesters. TMCD-modified poly (1,4-cyclohexylenedimethylene terephthalate) (PCTT) has been used to manufacture consumer products with good toughness, heat resistance and clarity. However, the suitability of PCTT in 3D printing had not been evaluated. Therefore, consumer plasticware was used as the starting material to investigate the suitability of this copolyester for fused deposition modeling (FDM). Chemical structure, mechanical properties, thermal behavior and viscoelastic properties of this copolyester were studied. NMR spectroscopy found that the copolyester had cyclohexanedimethanol (CHDM) and TMCD contents at 76.5 mol% and 20 mol% of total diol, respectively. 280 °C printing temperature and 110 °C bed temperature were suitable conditions for printing. Tg of PCTT was 103 °C (25 °C higher than PETG). Young's modulus and impact strength of printed PCTT were at least 100% and 65% higher than printed PETG, respectively. The ease of printing, superior mechanical properties and Tg (103 °C) make the PCTT random copolyester highly applicable in additive manufacturing.

Owing to its low cost and sustainable nature, lignocellulosic biomass has been utilized for reinforcing polymers, but it is crucial to understand the impact of high-ash concentrations in biomass on composite strength and processing. Biomass is not only desirable for biofuel production but could also have a strong market, if high-ash biomass is acceptable, for biocomposites. In this work, natural fibers (switchgrass and corn stover) were used to reinforce polylactic acid (PLA) to produce biocomposites. Natural fibers were pretreated to obtain fibers that contain different percentages of ash. The mechanical properties (such as Young's modulus, tensile strength, failure strain, storage modulus) of corn stover/PLA composites remained largely unaffected by the ash concentration of the biomass fibers, despite the large range of ash contents (2.2–11.9 wt%). However, the tensile strengths of switchgrass/PLA composites were slightly negatively affected by the ash concentration of the switchgrass fibers (0.7–2.1 wt%). Both the switchgrass/PLA and the corn stover/PLA composites exhibited a high-enough tensile strength (49–57 MPa) and suitable complex viscosity (2.0−7.0 kPa·s at the frequency of 3.2 rad/s). They are expected to be 3D-printable through an extrusion-based additive manufacturing process.

Interest in novel uses of biogas has increased recently due to concerns about climate change and greater emphasis on renewable energy sources. Although biogas is frequently used in low-value applications such as heating and fuel in engines or even just flared, reforming is an emerging strategy for converting biogas to syngas, which could then be used to obtain high-value-added liquid fuels and chemicals. Interest also exists due to the role of dry, bi-, and tri-reforming in the capture and utilization of CO2. New research efforts have explored efficient and effective reforming catalysts, as specifically applied to biogas. In this paper, we review recent developments in dry, bi-, and tri-reforming, where the CO2 in biogas is used as an oxidant/partial oxidant. The synthesis, characterization, lifetime, deactivation, and regeneration of candidate reforming catalysts are discussed in detail. The thermodynamic limitation and techno-economics of biogas conversion are also discussed.