Search

The textile industry is one of the most chemical-intensive processes, resulting in the unquestionable pollution of more than a quarter of the planet's water bodies. The high recalcitrant properties of some these pollutants resulted on the development of treatment technologies looking at the larger removal efficiencies, due to conventional systems are not able to completely remove them in their effluents. However, safeguarding the environment also implies taking into account indirect pollution from the use of chemicals and energy during treatment. On the other hand, the emerged technologies need to be economically attractive for investors and treatment managers. Therefore, the costs should be kept under control. For this reason, the present study focuses on a comparative Life Cycle Assessment and Life Cycle Costing of four scale-up scenarios aiming at mono and di-azo reactive dyes removal from textile wastewater. Two reactors (sequencing batch reactor and two-phase partitioning) were compared for different reaction environments (i.e., single anaerobic and sequential anaerobic-aerobic) and conditions (different pH, organic loading rates and use of polymer). In accordance with the results of each scenario, it was found that the three technical parameters leading to a change in the environmental profiles were the removal efficiency of the dyes, the type of dye eliminated, and the pollutant influent concentration. The limitation of increasing organic loading rates related to the biomass inhibition could be overcame through the use of a novel two-phased partitioning bioreactor. The use of a polymer at this type of system may help restore the technical performance (84.5 %), reducing the toxic effects of effluents and consequently decreasing the environmental impact. In terms of environmental impact, this is resulting into a reduction of the toxic effects of textile effluents in surface and marine waters compared to the homologous anaerobic-aerobic treatment in a sequencing batch reactor. However, the benefits achieved for the nature comes with an economic burden related to the consumption of the polymer. It is expected that the cost of investment of the treatment with the two-phase partitioning bioreactor rises 0.6-8.3 %, depending on market prices, compared to the other analyzed sequential anaerobic-aerobic technologies. On the other side, energy and chemical consumption did not prove to be limiting factors for economic feasibility., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Authors. Published by Elsevier B.V. All rights reserved.)

Landfill leachate is a highly polluted and toxic waste stream harmful to the environment and human health, its biological treatment, even if challenging, offers the opportunity of recovering valuable resources. In this study, we propose the application of an extractive membrane bioreactor equipped with a polymeric tubing, made of Hytrel, as an innovative device able to remove specific organic toxic compounds of the leachate and, at the same time, to produce an effluent rich in valuable chemicals suitable for recovery. The leachate treatment consists in a two-step process: the extraction of specific toxic compounds through the polymeric tubing based on the affinity with the polymer, and their subsequent biodegradation in controlled conditions in the bulk phase of the extractive membrane bioreactor, thus avoiding the direct contact of the microbial consortium with the toxic leachate. Three synthetic streams simulating leachates produced by landfills of typical industrial/hazardous waste, mixed municipal and industrial solid waste, and oil shale industry waste, whose toxic fraction is mainly constituted by phenolic compounds, have been tested. Successful performance was achieved in all the tested conditions, with high removal (≥98%) and biodegradation efficiencies (89-95%) of the toxic compounds. No mass transfer limitations across the tubing occurred during the operation and a marginal accumulation (in the range of 4-7%) into the polymer has been observed. Furthermore, volatile fatty acids and inorganic compounds contained in the leachates were fully recovered in the treated effluent. Feasibility study confirmed the applicability of the proposed bioreactor as a powerful technology able to achieve high toxic removal efficiency in leachate treatment and facilitate resource recovery., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2021 Elsevier B.V. All rights reserved.)

A tubing TPPB (Two-Phase Partitioning Bioreactor) was operated with the objective of verifying the effective treatment of a phenolic synthetic wastewater with simultaneous polymeric tubing bioregeneration by introducing tubing effluent recycle and modifications to the Hydraulic Retention Time (HRT). 2,4-dichlorophenol (DCP) was employed as the target substrate and the bioreactor was operated for a 3 month period under severe loading conditions (from 77 to 384 mg/L d) with HRT in the tubing in the range of 2-4 h. Tubing effluent recycle (recycle flow rate/influent flow rate ratio = 0.3) was applied when a loss of performance was detected arising from the increased load. For HRT values of 3 and 4 h, almost complete DCP removal was achieved after a few days (1-5) of operation while for the 2 h HRT (i.e. in the most severe loading condition) the DCP removal was ≥97%. A beneficial effect on the process performance arising from recycle application was evident for all the operating conditions investigated, and was confirmed by statistical analysis. Essentially complete polymer bioregeneration was achieved when the bioreactor was operated at the lowest HRT (i.e. 2 h), combined with the application of tubing effluent recycle. The results of this study highlighted several advantages of the tubing TPPB configuration in a comparative analysis of different regeneration options, including the possibility of operating continuously with simultaneous bioregeneration and without the need for additional units or operational steps and extra-energy consumption., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2020 Elsevier B.V. All rights reserved.)

Effective biological treatment of high salt content wastewater requires consideration of both salt and organic toxicity. This study treated a synthetic saline wastewater containing NaCl (100gL -1 ) and 2,4-dimethylphenol (1.2gL -1 ) with a hybrid system consisting of a biological reactor containing spiral-coiled polymeric tubing through which the mixed feed was pumped. The tubing wall was permeable to the organic contaminant, but not to the salt, which allowed transfer of the organic into the cell-containing bioreactor contents for degradation, while not exposing the cells to high salt concentrations. Different grades of DuPont Hytrel polymer were examined on the basis of organic affinity predictions and experimental partition and mass transfer tests. Hytrel G3548 tubing showed the highest permeability for 2,4-dimethylphenol while exerting an effective salt barrier, and was used to verify the feasibility of the proposed system. Very high organic removal (99% after just 5h of treatment) and effective biodegradation of the organic fraction of the wastewater (>90% at the end of the test) were observed. Complete salt separation from the microbial culture was also achieved., (Copyright © 2017 Elsevier B.V. All rights reserved.)

This work describes the application of a solid-liquid two-phase partitioning bioreactor (TPPB) for the removal of colour from a real textile wastewater containing reactive azo-dyes. Four polymers were tested over the pH range of 4-9 to select the most effective absorbant to be used as the partitioning phase in the TPPB. The best results were obtained with Hytrel 8206 at pH4 achieving ~70% colour removal, based on the dominant wavelength, in the first 5h of contact time, and 84% after 24h. Wastewater treatment was undertaken in a solid-liquid TPPB operated with Hytrel 8206 in sequential anaerobic-aerobic configuration. The reaction time of 23h was equally distributed between the anaerobic and aerobic phases and, to favour colour uptake, the pH was controlled at 4.5 in the first 4h of the anaerobic phase, and then increased to 7.5. Colour removal (for the dominant wavelength, 536nm) increased from 70 to 85% by modifying the bioreactor operation from single-phase to TPPB mode. Based on COD measurements nearly complete biodegradation of the intermediates produced in the anaerobic phase was obtained, both in the single-phase and two-phase mode, with better performance of the TPPB system reaching 75% COD Dye removal., (Copyright © 2016 Elsevier B.V. All rights reserved.)

The removal of a xenobiotic (4-chlorophenol) from contaminated water was investigated in a simulated continuous two-phase partitioning bioreactor (C-TPPB), fitted with coiled tubing comprised of a specifically-selected extruded polymer, Hytrel 8206. Wastewater flowed inside the tubing, the pollutant diffused through the tubing wall, and was removed in the aqueous bioreactor phase at typical biological removal rates in the C-TTPB simulated by varying aqueous phase throughput to the reactor. Operating over a range of influent substrate concentrations (500-1500mgL(-1)) and hydraulic retention times in the tubing (4-8h), overall mass transfer coefficients were 1.7-3.5×10(-7)ms(-1), with the highest value corresponding to the highest tubing flow rate. Corresponding mass transfer rates are of the same order as biological removal rates, and thus do not limit the removal process. The C-TPPB showed good performance over all organic and hydraulic loading ranges, with removal efficiencies of 4CP in the tubing wastewater stream always ≥96%. Additionally, the presence of the Hytrel tubing was able to buffer increases in organic loading to the hybrid system, enhancing overall process stability. Biological testing of the C-TPPB confirmed the abiotic test results demonstrating even higher 4-chlorophenol removal efficiency (∼99%) in the tubing stream., (Copyright © 2016 Elsevier B.V. All rights reserved.)

Sequential anaerobic-aerobic digestion has been demonstrated to be effective for enhanced sludge stabilization, in terms of increased solid reduction and improvement of sludge dewaterability. In this study, we propose a modified version of the sequential anaerobic-aerobic digestion process by operating the aerobic step under mesophilic conditions (T=37 °C), in order to improve the aerobic degradation kinetics of soluble and particulate chemical oxygen demand (COD). Process performance has been assessed in terms of "classical parameters" such as volatile solids (VS) removal, biogas production, COD removal, nitrogen species, and polysaccharide and protein fate. The aerobic step was operated under intermittent aeration to achieve nitrogen removal. Aerobic mesophilic conditions consistently increased VS removal, providing 32% additional removal vs. 20% at 20 °C. Similar results were obtained for nitrogen removal, increasing from 64% up to 99% at the higher temperature. Improved sludge dewaterability was also observed with a capillary suction time decrease of ~50% during the mesophilic aerobic step. This finding may be attributable to the decreased protein content in the aerobic digested sludge. The post-aerobic digestion exerted a positive effect on the reduction of microbial indicators while no consistent improvement of hygienization related to the increased temperature was observed. The techno-economic analysis of the proposed digestion layout showed a net cost saving for sludge disposal estimated in the range of 28-35% in comparison to the single-phase anaerobic digestion., (Copyright © 2015 Elsevier B.V. All rights reserved.)

The present study has provided a comparison between a conventional ex situ method for the treatment of contaminated soil, a soil slurry bioreactor, with a novel technology in which a contaminant is rapidly and effectively removed from the soil by means of absorptive polymer beads, which are then added to a two-phase partitioning bioreactor (TPPB) for biodegradation of the target molecule. 4-nitrophenol (4NP) was selected as a model contaminant, being representative of a large class of xenobiotics, and the DuPont thermoplastic Hytrel™ 8206 was utilized for its extraction from soil over ranges of soil contamination level, soil moisture content, and polymer:soil ratios. Since the polymers were able to rapidly (up to 77% and 85% in 4 and 24h respectively) and selectively remove the contaminant, the soil retained its nutrient and microflora content, which is in contrast to soil washing which can remove these valuable soil resources. After 4h of reaction time, the TPPB system demonstrated removal efficiency four times higher (77% vs 20%) than the slurry system, with expected concomitant savings in time and energy. A volumetric removal rate of 75 mg4NPh(-1) L(-1) was obtained in the TPPB, significantly greater than the value of 1.7 obtained in the slurry bioreactor. The polymers were readily regenerated for subsequent reuse, demonstrating the versatility of the polymer-based soil treatment technology., (Copyright © 2013 Elsevier B.V. All rights reserved.)

The applicability of a sequencing batch two phase partitioning bioreactor (TPPB) to the biodegradation of a highly toxic compound, 2,4-dichlorophenol (DCP) (EC(50)=2.3-40 mgL(-1)) was investigated. A kinetic study of the individual process steps (DCP absorption into the polymer, desorption and biodegradation) was performed and, based on favourable absorption/desorption characteristics (DCP diffusivity of 6.6×10(-8)cm(2)s(-1)), the commercial polymer Tone P787 (Dow Chemical), was utilized as the sequestering phase for TPPB operation. Batch kinetic biodegradation tests were performed in both single- and two-phase modes, and the Haldane equation kinetic parameters were estimated (k=1.3×10(-2) mgDCP mgVSS(-1)h(-1), K(I)=35 mgDCPL(-1) and K(s)=18 mgDCPL(-1)), confirming the highly toxic nature of DCP. Consistent with these findings, operation of the single-phase system showed that for an initial DCP concentration of 130 mg L(-1) the biomass was completely inhibited and DCP was not degraded, while the two-phase system achieved near-complete DCP removal. In sequencing batch mode the TPPB had a removal efficiency of 91% within 500 min for a feed of 320 mg L(-1), which exceeds the highest concentration previously degraded. These results have confirmed the effectiveness of the use of small amounts (5%, v/v) of inexpensive commercial polymers as the partitioning phase in TPPB reactors for the treatment of a highly toxic substrate at influent loads that are prohibitive for conventional single-phase operation, and suggest that similar detoxification of wastewater influents is achievable for other target cytotoxic substrates., (Copyright © 2012 Elsevier B.V. All rights reserved.)

Sequential anaerobic-aerobic digestion was applied to waste activated sludge (WAS) of a full scale wastewater treatment plant. The study was performed with the objective of testing the sequential digestion process on WAS, which is characterized by worse digestibility in comparison with the mixed sludge. Process performance was evaluated in terms of biogas production, volatile solids (VS) and COD reduction, and patterns of biopolymers (proteins and polysaccharides) in the subsequent digestion stages. VS removal efficiency of 40%, in the anaerobic phase, and an additional removal of 26%, in the aerobic one, were observed. For total COD removal efficiencies of 35% and 25% for anaerobic and aerobic stage respectively, were obtained. Kinetics of VS degradation process was analyzed by assuming a first order equation with respect to VS concentration. Evaluated kinetic parameters were 0.44 ± 0.20 d(-1) and 0.25 ± 0.15 d(-1) for the anaerobic stage and aerobic stage, respectively. With regard to biopolymers, in the anaerobic phase the content of proteins and polysaccharides increased to 50% and 69%, respectively, whereas in the subsequent aerobic phase, a decrease of 71% for proteins and 67% for polysaccharides was observed. The average specific biogas production 0.74 m(3)/(kg VS destroyed), was in the range of values reported in the specialized literature for conventional anaerobic mesophilic WAS digestion., (Copyright © 2011 Elsevier B.V. All rights reserved.)

The biological treatment of phenolics is constrained by the inherent cytotoxicity of these compounds. One method to alleviate such toxicity is to add a sequestering phase to absorb, and subsequently release, the substrate(s) to the micro-organisms; such a system is termed a Two Phase Partitioning Bioreactor. Here we have compared the performance of a TPPB, relative to single phase operation, in which a small volume (5%, v/v) of beads of the polymer Hytrel 8206 was used to treat aqueous mixtures of 2,4-dimethylphenol and 4-nitrophenol. Hytrel 8206 was selected from a range of polymers that were tested for their partition coefficients (PCs) for the target molecules, with the more hydrophobic compound (2,4-dimethylphenol) having a higher PC value (201) than 4-nitrophenol (143). Significantly increased removal rates for both substrates were demonstrated in TPPB mode relative to single phase operation. Additionally, the differential release of the compounds to the aqueous phase and their distinct PC values changed the kinetic pattern of the biotreatment system, smoothing out the cellular oxygen demand. Release of the substrates by the polymer over 60 operating cycles was virtually complete (>97%) demonstrating the reusability and robustness of the use of polymers in overcoming cytotoxicity of phenolic substrates., (Copyright © 2011 Elsevier B.V. All rights reserved.)