Search

Concrete production unfavourably affects the environment due to high energy demands of cement production and consumption of limited natural resources. Therefore, waste utilization in fabrication of cementitious material is beneficial and legitimate. Significant reduction of environmental impact can be secured by utilization of various types of wastes or byproducts used for a partial substitution of cement binder or aggregates. However, the use of waste materials usually leads to deterioration of material properties of the designed composites. Therefore, it is very important to thoroughly investigate important materials properties to verify performance and practical usability of the newly designed materials. In this paper, three types of concrete mixes were designed. The reference concrete involved fine and coarse natural riverbed aggregates and two other mixes were designed using both, natural and recycled aggregates represented by crushed concrete paving cobbles. Concretes were tested in terms of basic physical properties (bulk density), mechanical properties (compressive strength), thermal properties (thermal conductivity, specific heat capacity, thermal diffusivity), and hygric properties (water vapour diffusion resistance factor, water vapour sorption at 97% RH, water absorption coefficient, moisture diffusivity) and experimentally determined data were compared and discussed. It was observed that materials properties of concretes with recycled aggregates are comparable with those of the reference concrete which is a promising fact from the environmental point of view.

Sewage sludge is a semi-solid waste material created as a result of the sewage treatment of industrial or municipal wastewater. Because the laws and regulations of the European Union require not only a reduction in waste generation but also the preparation of waste for reuse and disposal, it is necessary to look for new methods of the application of sewage sludge as part of sustainable waste management. In this study, ash formed as a result of the combustion of sewage sludge from the sewage treatment plant in Płaszów, Krakow in a fluidised bed furnace at a temperature of around 800°C was used. Sewage sludge ash (SSA) contains over 30% SiO2 and approx. 10% Al2O3, which indicates potential applications in geopolymer materials. In this study, samples of geopolymer mortars with a binder containing sewage sludge ash as well as fly ash (FA) and ground granulated blast furnace slag (GGBFS) were prepared. The mechanical parameters were determined after 2, 7, 14, and 28 days. The results show that the sewage sludge ash-based geopolymer shows binding properties at ambient temperature and, depending on the presence of FA and/or GGBFS, the compressive strength varies from 5 to 45 MPa after 28 days. The aim of the research was also to determine the total content of heavy metals (Sb, As, Cr, Cd, Cu, Ni, Pb, Hg, Zn) in the raw materials used and their leachability from the structure of the hardened materials. Immobilisation of heavy metals is very promising. Based on the results of tests, it seems possible to use SSA in geopolymer materials, but not as the main component of the binder.

Geopolymers may be considered as an alternative materials to Portland cement ones, providing an opportunity to exploit industrial wastes or co-products with promising short and long-term performances in the construction field, f.ex. for reparation issues. However, these materials are porous and consequently their durability depends on the risk of intrusion of aggressive agents. In order to assess their durability, we propose to investigate in this study gas permeability of sound and mechanically loaded specimens. Loading is performed using a splitting tensile test driven by a crack opening displacement up to a level of 50 microns. Tests are performed on four types of blended fly-ash (FA) and ground granulated blast furnace slag (GGBFS) geopolymer mortars, containing four different levels of GGGBF slag in the binder: 0%, 10%, 30% and 50% wt. Results show a positive effect of blending with slag in terms of modulus of elasticity and tensile and compressive strength, as well as the permeability. However, permeability recovery after cracking is the lowest when blending is the highest.

Inefficient use of end-of-life materials in combination with depletion of primary sources can be understood as a significant factor that motivates to effective waste material recycling and reuse. Since the construction industry produces millions of tons of building materials, which are continuously reaching their service life end, there is a great potential for their reuse instead of simple landfilling. In this light, concrete is a versatile building material that might incorporate lots of recycled building materials as it is demanding on primary sources. A substitution of coarse aggregates by recycled products is, therefore, one of the ways how to mitigate these environmental burdens. This paper aims at evaluation of environmental contributions of concrete with coarse aggregates being substituted by crushed concrete pavements. Various amounts of recycled aggregates were assumed (0%, 50%, and 100%) to reveal the environmental impacts. The analysis incorporates all inputs and outputs related to the production of concrete and recycling of concrete pavements (raw materials production, processing, transport emissions, energy production, etc.). The results indicate that substitution of coarse aggregates by recycled concrete pavements may bring significant mitigation of environmental impacts and hence it deserves further investigation.

The advent of modern aluminosilicate binders has resulted in practical uses for fly ash, which belongs to the group of secondary mineral raw materials; this provides an interesting alternative to cementitious binders, which have a large carbon footprint. Geopolymers mineral binders with a growing range of applications in construction. Their inorganic, amorphous structure endows them with better resistance to high temperature compared to cementitious binders. In this study, the alkaline activation of aluminosilicate Połaniec Fly Ash made it possible to obtain noncementitious material with compressive strength of 18.5 MPa. The article presents the results of a comparison of characteristics of geopolymer mortar and Portland cement mortar after thermal exposure.

This article presents results of fire spalling tests on small concrete slabs and studies of material parameters that may increase its occurrence. Experimental techniques enabling to study and determination of material features are presented and discussed. Experimental studies on spalling behaviour of elements were carried out on seven different concrete mixes with constant content of cement paste and mortar. Research aimed at determining influence of the following parameters: w/c ratio (0.30; 0.45; 0.60), cement type (CEM I, CEM III) and type of aggregates (riverbed gravel, granite, basalt) on fire concrete spalling. Paper discusses also the influence of cold rim that forms while testing slab-like element is subjected to one-side heating.