Search

A bullet signature measurement system based on a stylus instrument was developed at the National Institute of Standards and Technology (NIST) for the signature measurements of NIST RM (Reference Material) 8240 standard bullets. The standard bullets are developed as a reference standard for bullet signature measurements and are aimed to support the recently established National Integrated Ballistics Information Network (NIBIN) by the Bureau of Alcohol, Tobacco and Firearms (ATF) and the Federal Bureau of Investigation (FBI). The RM bullets are designed as both a virtual and a physical bullet signature standard. The virtual standard is a set of six digitized bullet signatures originally profiled from six master bullets fired at ATF and FBI using six different guns. By using the virtual signature standard to control the tool path on a numerically controlled diamond turning machine at NIST, 40 RM bullets were produced. In this paper, a comparison parameter and an algorithm using auto-and cross-correlation functions are described for qualifying the bullet signature differences between the RM bullets and the virtual bullet signature standard. When two compared signatures are exactly the same (point by point), their cross-correlation function (CCF) value will be equal to 100%. The measurement system setup, measurement program, and initial measurement results are discussed. Initial measurement results for the 40 standard bullets, each measured at six land impressions, show that the CCF values for the 240 signature measurements are higher than 95%, with most of them even higher than 99%. These results demonstrate the high reproducibility for both the manufacturing process and the measurement system for the NIST RM 8240 standard bullets.

Ballistics imaging technology has received national attention as a potent tool for moving the law enforcement response to violent gun criminals forward by linking multiple crime scenes to one firearm. This study examines the impact of ballistics imaging technology on the productivity of the Boston Police Department's Ballistics Unit. Using negative binomial regression models to analyze times series data on ballistics matches, we find that ballistics imaging technology was associated with a more than sixfold increase in the monthly number of ballistics matches made by the Boston Police Department's Ballistics Unit. Cost-effectiveness estimates and qualitative evidence also suggest that ballistics imaging technology allows law enforcement agencies to make hits that would not have been possible using traditional ballistics methods.

Four cases of homicide, in which silenced firearms were used, are reported and supplemented by data from experimental investigations regarding wound features, marks, traces, and ballistic behavior. Wound features are largely determined by the construction of the silencer. In one case, even a muzzle imprint was produced by a silenced weapon fired at contact range. In general, silencers are likely to result in a decrease in bullet energy and accelerated energy release in the target (tissue). In terms of wound morphology, silencers produced a reduction in or even a lack of the contact ring (ring of dirt). In close-range and contact wounds, any features indicative of shots fired at close range were missing (such as soot deposit and powder tattooing). It is also worth mentioning that biological matter may get into the silencer in shots fired at contact range.

Recently marketed PMC (Pan Metal Corporation) Ultramag tubular hollow point ammunition is uniquely constructed with a two-part projectile composed of a tubular copper bullet and a Teflon wad. A fatal gunshot wound with this ammunition is described. A unique radiographic pattern and the results of test firing are also presented.

This paper reviews the use of trace evidence recovered from spent bullets in helping to establish trajectories. The use of information derived from such trace evidence combined with that from geometrical techniques of trajectory reconstruction and other data is discussed. Five cases are reviewed in which the analysis of trace evidential materials adhering to bullets was used to help reconstruct the event.

It was determined that tempered glass automobile windows may severely influence the trajectory of .38 Special projectiles. In replicating an actual case situation, deflections as great as 26.4 degrees were observed with jacketed hollow-point ammunition, and as high as 10.8 degrees for lead ammunition.

Test shots were fired into real and simulated automobile ceilings in an attempt to determine what types of evidence should be available for determining the direction of flight of the bullet. The information obtained was used in a shooting investigation.

The authors report two cases in which examination of foreign material embedded in or adherent to bullets provided critical information in the reconstruction of a crime scene. Analysis of small particles by scanning electron microscopy (SEM) and energy dispersive X-ray analysis (EDXA) can be accomplished without destruction or injury of the particles. In one case, the detection and identification of mineral fragments embedded near the nose of a bullet provided conclusive evidence that the bullet had ricocheted from a fireplace before striking the victim. In the second case, analysis of particles from two bullets identified them as them as bone fragments, thus proving which shots fired from a police officer's gun had killed a suspected burglar. SEM-EDXA has not been widely used to identify such material on bullets, but should be considered a potentially powerful tool in forensic science.

Small angles of projectile entry are difficult to determine in two-dimensional targets or in three-dimensional targets where internal deflection has taken place. This results from the fact that small errors in measurement lead to large errors in the calculation of the sine function used in the estimation of the angular projection of a circle onto an inclined plane at angles of less than 20° from the normal. The use of a bullet tip scale, constructed to the dimensions of the entering projectile, allows a significantly more accurate determination of small angles of entry in targets not subject to stretching. A comparison of the relative error inherent in calculating entry angle using the sine function and measuring the angle using the bullet tip scale demonstrates the suitability of using the tip scale at angles less than 20° and the sine function at entry angles greater than 20°.

Great controversy has surrounded the replacement of the 7.62-mm caliber by the reduced 5.56-mm caliber as the standard U.S. military rifle. Although its relevance to human wounding can be debated, the terminal ballistics of military small arms in ordnance gelatin remains a convenient medium for comparative testing. In the present study, 7- by 10- by 24-in. (18 by 25 by 61 cm) blocks of 20% ordnance gelatin were fired upon from a range of 19 ft (6 m) under high-speed cinemagraphic surveillance. The tendency of the M193 5.56-mm full metal jacket projectile to break up in soft tissue simulant was confirmed as a fundamental difference from the 7.62-mm M80 NATO ball.

Air and spring actuated guns firing spherical or elongated projectiles are widely used for target practice and pest shooting. Although their ability to inflict physical injury is well recognized, the fact that some of these guns are potentially lethal is surprising to those not familiar with their history and ballistics. The Austrian armies, for example, used air rifles against the French during the Napoleonic wars of 1799–1809 [1]. These were rifles of 12.8-mm (1.50-in.) caliber and had an effective range between 100 and 150 yards (91 and 137 m). An air rifle of unknown caliber was also carried by the Lewis and Clark expedition of 1804–1806 [2] and was used on occasion to kill deer-size animals as well as birds and small game.