Search

A free-hanging riser (FHR) is a typical riser configuration seen in the disconnected drilling riser, the water-intake riser, and the deep-sea mining riser. In offshore productions, these marine risers will move back and forth in water and further generate an equivalent oscillatory current around themselves, due to the vessel motions. Both in full-scale marine operations and model tests, it has been reported that such oscillatory current leads to riser vortex-induced vibration (VIV) and therefore causes structural fatigue damage. Recently, there have been some attempts to numerically predict vessel motion-induced VIV on the compliant production risers, with emphasize on relatively large Keulegan-Carpenter (KC) numbers. In the real marine operations, the risers experience small KC number scenarios during most of their service life. Therefore, the investigation of vessel motion-induced VIV under small KC number is of great significance, especially considering its contribution to the fatigue damage. In this paper, numerical investigation of VIV of a FHR attached to a floating vessel is carried out. A new response frequency model for vessel motion-induced VIV under small KC numbers is proposed and implemented in vivana. Validation of the proposed numerical methodology is performed against the published experimental results, where a good agreement is achieved. [ABSTRACT FROM AUTHOR]

Deepwater risers are susceptible to vortex-induced vibrations (VIV) when subjected to currents. When responding at high modes, fatigue damage in the inline (IL) direction may become equally important as the crossflow (CF) components. Accurate calculation of both IL and CF responses is therefore needed. Empirical VIV prediction programs, such as VIVANA "Passano et al. (2016, "VIVANA--Theory Manual Version 4.8," Trondheim, Norway)," SHEAR7 "(Vandiver, J. K., and Li, L., 2007, "Shear7 v4.5 Program Theoretical Manual," Department of Ocean Engineering, Massachusetts Institute of Technology, Cambridge, MA)," and VIVA "Triantafyllou et al. (1999, "Pragmatic Riser VIV Analysis," Offshore Technology Conference, Houston, TX, May 3-6, Paper No. OTC-10931-MS.)" are the most common tools used by the offshore industry. Progress has been seen in the prediction of CF responses. Efforts have also been made to include an IL load model in VIVANA. A set of excitation coefficient parameters were obtained from rigid cylinder test and adjusted using measured responses of one of the flexible cylinder VIV tests. This set of excitation coefficient parameters is still considered preliminary and further validation is required. Without an accurate IL response prediction, a conservative approach in VIV analysis has to be followed, i.e., all current profiles have to be assumed to be unidirectional or acting in the same direction. The purpose of this paper is to provide a reliable combined IL and CF load model for the empirical VIV prediction programs. VIV prediction using the existing combined IL and CF load model in VIVANA is validated against selected flexible cylinder test data. A case study of a deepwater top tension riser (TTR) has been carried out. The results indicate that VIV fatigue damage using two-dimensional directional current profiles is less conservative compared to the traditional way of using unidirectional current profiles. [ABSTRACT FROM AUTHOR]

Vortex-induced vibrations (VIV) can lead to fast accumulation of fatigue damage and increased drag loads for slender marine structures. VIV responses mainly occur at the vortex shedding frequency, while higher harmonics can also be excited. Recent VIV model tests with flexible pipes have shown that higher harmonics in the crossflow (CF) direction can contribute to the fatigue damage significantly due to its higher frequency. Rigid cylinder experiments show that the CF third-order harmonics are more pronounced when the motion orbit is close to a "figure 8" shape and the cylinder is moving against the flow at its largest CF motion. However, there is still lack of understanding of when and where higher harmonics occur for a flexible pipe. Therefore, significant uncertainty remains on how to account for fatigue damage due to higher harmonics in VIV prediction. In the present paper, representative VIV data from various riser model test campaigns are carefully studied and analyzed. The key parameters that influence the magnitude of the third-order harmonic stress are found to be the bending stiffness, the reduced velocity, and the orbit stability. The experimental data are analyzed in order to assess the impact of each parameter on the third-order harmonic stress. A preliminary empirical response model to estimate the maximum CF third-order harmonic stress based on these identified structural and hydrodynamic parameters has been proposed. The results of this study will contribute to reduce the uncertainty and unnecessary conservatism in VIV prediction. [ABSTRACT FROM AUTHOR]

Drilling risers are regularly deployed in deep water (over 1500 m) with large sections covered in buoyancy modules. The smooth cylindrical shape of these modules can result in significant vortex-induced vibration (VIV) response, causing an overall amplification of drag experienced by the riser. Operations can be suspended due to the total drag adversely affecting top and bottom angles. Although suppression technologies exist to reduce VIV (such as helical strakes or fairings), and therefore reduce VIV-induced amplification of drag, only fairings are able to be installed onto buoyancy modules for practical reasons, and fairings themselves have significant penalties related to installation, removal, and reliability. An innovative solution has been developed to address this gap: longitudinally grooved suppression (LGS). Two model testing campaigns were undertaken: small scale (subcritical Reynolds number flow), and large scale (postcritical Reynolds number flow) to test and confirm the performance benefits of LGS. The testing campaigns found substantial benefits measured in hydrodynamic performance that will be realized when LGS modules are deployed by operators for deepwater drilling operations. [ABSTRACT FROM AUTHOR]

Slender offshore structures in deep water subjected to currents may experience vortex-induced vibrations (VIV), which can cause significant fatigue damage. Extensive experimental researches have been conducted to study the VIV in the past several decades. However, most of the experimental works have small-scale models and relatively low Reynolds number (Re)--"subcritical" or even lower Reynolds number regime. There is a lack of full understanding of the VIV in prototype Re flow regime. Applying the results with low Re to a full-scale riser with prototype Re might have uncertainties due to the scaling effects. In addition, the surface roughness of the riser is also an important parameter, especially in critical Re regime, which is the case for prototype risers. In the present study, two full-scale rigid riser models with different surface roughness ratios were tested in the towing tank of MARINTEK in 2014. Stationary tests, pure crossflow (CF) free oscillation tests, and forced/controlled motion tests were carried out. Several conclusions could be made: The drag coefficient is dependent on the Re number and surface roughness ratio. At critical and supercritical flow regimes, the displacement amplitude ratio is less sensitive to Re than that at lower Re. The displacement amplitude ratio in subcritical flow regime is significantly larger than that in critical and supercritical flow regimes. Two excitation regions for the 'smooth riser' and one excitation region for the "rough riser" are identified. [ABSTRACT FROM AUTHOR]

A model test of a free-hanging riser under vessel motion and uniform current is performed in the ocean basin at Shanghai Jiao Tong University to address four topics: (1) confirm whether vortex-induced vibration (VIV) can happen due to pure vessel motion; (2) to investigate the equivalent current velocity and Keulegan-Carpenter (KC) number effect on the VIV responses; (3) to obtain the correlations for free-hanging riser VIV under vessel motion with VIV for other compliant risers; and (4) to study the similarities and differences with VIV under uniform current. The top end of the riser is forced to oscillate or move, in order to simulate vessel motion or ocean current effects. Fiber Bragg Grating (FBG) strain sensors are used to measure the riser dynamic responses. Experimental results confirm that the free-hanging riser will experience significant out-of-plane VIV under vessel motion. Meanwhile, vessel motion-induced VIV responses in terms of response amplitude, response frequency, and cross section trajectories under different test cases are further discussed and compared to those under ocean uniform current. Most importantly, the correlation among VIV response frequency, vortex shedding pairs, and maximum KC number KCmax is revealed. The presented work is supposed to provide useful references for gaining a better understanding on VIV of a free-hanging riser and for the development of future prediction models. [ABSTRACT FROM AUTHOR]

This paper investigates the phase angles of the vibrations and hydrodynamic forces by the model testing of a flexible riser's vortex-induced vibration (VIV) under uniform flow. The VIV displacement of the riser is derived from the measured strains in the cross-flow (CF) and inline (IL) directions. Then, the hydrodynamic forces are obtained by the dynamic equation of an Euler-Bernoulli beam based on the results of VIV displacement. The characteristics of the phase angle of displacement and the hydrodynamic forces are analyzed. The results show that the phase angles of displacement and the hydrodynamic forces are almost identical at different cross sections of the riser under uniform flow. Moreover, within two adjacent vibration nodes in IL direction, the phase angle almost kept constant, while had a 180 deg change at the two sides of each vibration node. When the reduced velocity varies from 5.25 to 7.5, the phase angles of displacement derived from the flexible riser's VIV are 45 deg larger than those from the rigid cylinder's self-excited vibration. [ABSTRACT FROM AUTHOR]

To achieve a reliable structural model for vortex-induced vibration (VIV) the prediction of flexible risers, this paper employs structural systems with different geometrical nonlinearities (including a linear structure, a nonlinear one, a coupled cross-flow, and axial nonlinear one) and a classical oscillator to simulate cross-flow VIV. By comparing the experimental and simulation results, it is found that when the drag coefficient is assumed to be a fixed constant along the cylinder (i.e., the damping model is linear function of current velocity), it can affect the vibration amplitude considerably and may alter the dominant modes. When the excited mode of VIV is bending-stiffness dominant, the cross-flow structural nonlinearities can have a profound stiffening effect on vibration response. Although the introduction of axial deformation can reduce this function, the coupled cross-flow and axial nonlinearities still have the effect of decreasing the VIV amplitude. [ABSTRACT FROM AUTHOR]

In order to assess the effects of vortex-induced vibration (VIV) and to ensure riser integrity, field monitoring campaigns are often conducted wherein the riser response is recorded by a few data sensors distributed along the length of the riser. In this study, two empirical techniques-proper orthogonal decomposition (POD) and weighted waveform analysis (WWA)-are sequentially applied to the data; together, they offer a novel empirical procedure for fatigue damage estimation in an instrumented riser. The procedures are briefly described as follows: first, POD is used to extract the most energetic spatial modes of the riser response from the measurements, which are defined only at the available sensor locations. Accordingly, a second step uses WWA to express each dominant POD mode as a series of riser natural modes that are continuous spatial functions defined over the entire riser length. Based on the above empirically identified modal information, the riser response over the entire length is reconstructed in reverse-i.e., compose identified natural modes into the POD modes and, then, assemble all these dominant POD modal response components into the derived riser response. The POD procedure empirically extracts the energetic dynamic response characteristics without any assumptions and effectively cleans the data of noisy or less important features; this fundamental application of WWA is used to identify dominant riser natural modes-all this is possible using the limited number of available measurements from sensor locations. Application of the procedure is demonstrated using experimental data from the Norwegian Deepwater Programme (NDP) model riser. [ABSTRACT FROM AUTHOR]