Search

Two geotechnical centrifuge tests were designed to elicit the influence of soil-foundation-structure interaction (SFSI) and structure-soil-structure interaction (SSSI) effects on the seismic demands of an inelastic frame structure founded on individual spread footings. Four experimental cases were considered: (1) SFSI of an individual inelastic frame structure (baseline case); (2) in-plane SSSI between the frame structure and a large elastic wall structure designed to respond predominately in a rocking mode; (3) anti-plane SSSI between the frame and wall structures; and (4) combined in-plane and anti-plane SSSI between the frame structure and two wall structures. Results from Cases 1, 2, and 4 are analyzed considering 13 demand parameters. The peak seismic demands from the baseline case are compared to the peak demands from the SSSI cases to elicit the impacts of building adjacency. The number of earthquake motions that resulted in increases or decreases in the seismic demands in the frame structure are tracked for the SSSI cases. For these tests, SSSI consistently results in increased peak foundation moment and foundation base shear demands, regardless of the geometric layout of the structures. These increases propagate throughout the superstructure, resulting in increases in moment, shear and curvature ductility demands in the structural components. SSSI effects are observed to be most significant for low-to-moderate intensity earthquake motions, suggesting that particular consideration should be given to the likelihood of SSSI for highly probable earthquakes. [ABSTRACT FROM AUTHOR]

The use of jet grouting columns to increase the bearing capacity and reduce the settlements of foundations is dealt with, the aim being to formulate a complete design procedure where theoretical analyses and site observations are combined. The study is based on experimental results reported in the literature, which show that jet grouting columns are able to transfer high vertical loads to the surrounding soil but also that structural collapse may locally occur because of a sudden narrowing of their cross sections and/or poor soil cementation. Noticeable attention has been then given to these aspects by interpreting the results of full-scale tests specifically performed to investigate the characteristics of jet grouting columns and their mechanical interaction with the surrounding soil. The results of this analysis form the basis of a numerical method developed to simulate the response of vertically loaded rafts supported by arrays of columns. The nonlinear load-settlement response of axially loaded columns is modeled with the load-transfer curves method customized to account for the irregular shape of jet grouting columns. Extension of the analysis to the whole reinforced foundation is accomplished by considering the mutual interaction between the columns and the upper concrete raft. The variation of column properties is statistically evaluated from the results of field trials, simulated with probabilistic models and introduced into the calculation with a Monte Carlo simulation technique. The main advantages of the proposed method is that the design limit load of the foundation can be expressed in terms of acceptable probability of failure and that the uncertainty arising from the jet grouting process can be experimentally quantified and rationally introduced in the analysis. Benefits and limitations of reinforcement with jet grouting are finally discussed by applying the proposed method to a case study. [ABSTRACT FROM AUTHOR]

There is currently a lack of established calculation methods for the geotechnical design of heat exchanger piles, although the technology is experiencing a fast expansion. Instead of quantifying the effects of temperature changes on the static behavior of heat exchanger piles, the common geotechnical practice is to apply a large overall security factor. This is done to be on the side of safety with respect to thermal effects. The few existing in situ experiments show that applying a thermal load induces a significant change in the stress-strain state of a pile. This paper presents a geotechnical numerical analysis method based on the load-transfer approach that assesses the main effects of temperature changes on pile behavior. The method is validated on the basis of in situ measurements of the loads and deformations experienced by heat exchanger test piles. The occurrence of critical design situations is further discussed. Some conclusions are formulated on concrete failure and the full mobilization of the pile shaft friction and base resistance during the operation of the heat exchange system. [ABSTRACT FROM AUTHOR]

The reinforcement of soft soils by rigid inclusions is a practical and economical technique for wide-span buildings and the foundations of embankments. This method consists of placing a granular layer at the top of the network of piles to reduce vertical load on the supporting soil and vertical settlement of the upper structure. The study focuses on the modeling of load-transfer mechanisms occurring in the reinforced structure located over the network of piles with a coupling between the finite-element method (geosynthetic sheets) and discrete element method (granular layer; concrete slab in some cases). The importance of granular layer thickness to increase load-transfer intensity and to reduce vertical settlement was observed. However, without a basal geosynthetic sheet, the compressibility of soft soil has a great influence on the mechanisms. A method predicting the intensity of load transfers was proposed, based on Carlsson's solution. The main parameters concerned are the geometry of the work and the peak and residual friction angles of the granular layer. [ABSTRACT FROM AUTHOR]

Tapered piles in comparison to cylindrical piles can be beneficial in terms of the load capacity. In this paper, estimation of the load capacity for tapered piles using cone penetration test (CPT) resistance was investigated. Fourteen calibration chamber load tests using different pile types and six CPTs were conducted under various soil conditions. From the calibration chamber test results, the total, base, and shaft load capacities were analyzed in terms of soil conditions and taper angle. To evaluate CPT-based load capacity of tapered piles, normalized base and shaft resistances were obtained from normalized unit load-settlement curves. Based on the normalized base and shaft resistances, design equations that can be used to evaluate the base and shaft resistances of tapered piles were proposed. The proposed method is valid for sands of medium to dense conditions, while it may result in unconservative predictions for loose sands. To check the accuracy of the proposed method, field load tests using both cylindrical and tapered piles were conducted and compared with the predictions using the proposed method. A simplified approach using an equivalent cylindrical pile was also investigated and compared. [ABSTRACT FROM AUTHOR]

The capacity of a pile-soil system can be obtained by pushover analysis using the beam-on-nonlinear-Winkler foundation model. When the pile section enters the plastic state, the plastic hinge method is usually adopted to model its postyielding flexural behavior. The propagation of the plastic zone in a pile can be traced using a series of plastic hinges distributed along the pile that is embedded in the soil. This study proposes a proper model for arranging the distributed plastic hinges along the depths of the pile that are prone to yielding. A modified definition of plastic curvature is proposed herein in order to correctly simulate the nonlinear flexural behavior of a pile. Examples are presented to show the effectiveness of the proposed model. [ABSTRACT FROM AUTHOR]

There is generally a physical limit to the smallest possible capacity for a deep foundation. However, a lower bound on the capacity has rarely been accounted for in performing reliability analyses and developing reliability-based design codes. The objectives of this paper are to investigate the effect of having a lower-bound capacity on the reliability of a geotechnical engineering system and to propose a load and resistance factor design (LRFD) checking format that includes information on the lower-bound capacity in design. It is concluded that a lower-bound capacity can cause a significant increase in the calculated reliability for a geotechnical design even if it is an uncertain estimate. Two alternative LRFD formats that incorporate lower-bound capacities and that would not require substantive changes to existing codes are proposed. Real-world examples dealing with the design of onshore and offshore foundations indicate that the incorporation of a lower-bound capacity into design is expected to provide a more realistic quantification of reliability for decision-making purposes and therefore a more rational and efficient basis for design. [ABSTRACT FROM AUTHOR]

This technical note develops a design approach that integrates economic design optimization with reliability-based methodologies to rationally account for geotechnical-related uncertainties. The geotechnical related uncertainties are addressed using a reliability-based approach in the assessment of ultimate limit state (ULS) and serviceability limit state (SLS) requirements. This design approach is illustrated using an example of spread foundation under drained uplift loading. Comparison of the economically optimized design with conventional designs shows that cost of the economically optimized design is lower than that of other feasible designs, and increasing foundation depth is a relatively effective way to increase uplift capacity. Impacts of geotechnical property uncertainties on foundation construction costs are quantified, and the results form a basis of a quantitative cost-benefit analysis of reducing geotechnical property uncertainties. Operative horizontal stress coefficient (K) is shown to be the key parameter that significantly affects the design of a spread foundation under drained uplift, and therefore, deserves attention in site investigation. For a typical allowable uplift displacement ya=25 mm, the spread foundation design is dictated by the ULS requirement, and the effect of ya, or SLS requirement, is negligible. [ABSTRACT FROM AUTHOR]

Pile foundations located within consolidating ground are commonly subjected to negative skin friction (NSF) and failures of pile foundations related to dragload (compressive force) and downdrag (pile settlement) have been reported in the literature. This paper reports the results of four centrifuge model tests, which were undertaken to achieve two objectives: first, to investigate the response of a single pile subjected to NSF with different pile tip location with respect to the end-bearing stratum layer; and second, to study the behavior of floating piles subjected to NSF with and without shielding by sacrificing piles. In addition, three-dimensional numerical analyses of the centrifuge model tests were carried out with elastoplastic slip considered at the pile-soil interface. The measured maximum β value at unprotected single end-bearing and floating pile was similar and slightly smaller than 0.3. On the contrary, smaller β values of 0.1 and 0.2 were mobilized at the shielded center piles for pile spacings of 5.0 d and 6.0 d, respectively. The measured maximum dragload of the center pile in the group at 5.0 d and 6.0 d spacing was only 53% and 75% of the measured maximum dragload of an isolated single pile, respectively. Correspondingly, the measured downdrag of the center pile was reduced to about 57% and 80% of the isolated single pile. Based on the numerical analyses, it is revealed that sacrificing piles “hang up” the soil between the piles in the group and, thus, the vertical effective stress in the soil so reduced, as is the horizontal effective stress acting on the center pile. This “hang-up” effect reduces with an increase in pile spacing. For a given pile spacing, shielding effect on dragload is larger than that on downdrag. [ABSTRACT FROM AUTHOR]

Numerous cone penetration test (CPT)-based methods exist for calculation of the axial pile capacity in sands, but no clear guidance is presently available to assist designers in the selection of the most appropriate method. To assist in this regard, this paper examines the predictive performance of a range of pile design methods against a newly compiled database of static load tests on driven piles in siliceous sands with adjacent CPT profiles. Seven driven pile design methods are considered, including the conventional American Petroleum Institute (API) approach, simplified CPT alpha methods, and four new CPT-based methods, which are now presented in the commentary of the 22nd edition of the API recommendations. Mean and standard deviation database statistics for the design methods are presented for the entire 77 pile database, as well as for smaller subset databases separated by pile material (steel and concrete), end condition (open versus closed), and direction of loading (tension versus compression). Certain methods are seen to exhibit bias toward length, relative density, cone tip resistance, and pile end condition. Other methods do not exhibit any apparent bias (even though their formulations differ significantly) due to the limited size of the database subsets and the large number of factors known to influence pile capacity in sand. The database statistics for the best performing methods are substantially better than those for the API approach and the simplified alpha methods. Improved predictive reliability will emerge with an extension of the database and the inclusion of additional important controlling factors affecting capacity. [ABSTRACT FROM AUTHOR]

This paper describes the development and application of design charts for piled embankment designs. It outlines the computational approach adopted, the geotechnical profiles used, and the application of the design procedure using the charts. The soil profile used for the charts is representative of a Malaysian soft clay profile, involving a more or less normally consolidated soil, with a strength and stiffness that varies linearly with depth. Such a profile is typical of the ground conditions in a variety of countries in the Southeast Asian region. The design charts address the issues of pile capacity, settlement due to embankment load, settlement due to a temporary piling construction platform, and lateral response of piles near the edge of the embankment. The charts consider variations in ground conditions, embankment height, pile length, and pile spacing. An illustrative example is given to demonstrate the use of the charts. [ABSTRACT FROM AUTHOR]

Often, the use of traditional techniques in geotechnical engineering faces obstacles of economical and environmental nature. The addition of cement becomes an attractive technique when the project requires improvement of the local soil. The treatment of soils with cement finds application, for instance, in the construction of pavement base layers, in slope protection of earth dams, and as a support layer for shallow foundations. However, there are no dosage methodologies based on rational criteria as exist in the case of the concrete technology, where the water/cement ratio plays a fundamental role in the assessment of the target strength. This study therefore aims to quantify the influence of the amount of cement, the porosity and the moisture content on the strength of a sandy soil artificially cemented, as well as to evaluate the use of a water/cement ratio and a voids/cement ratio to assess its unconfined compression strength. A number of unconfined compression tests, triaxial compression tests, and measurements of matric suction were carried out. The results show that the unconfined compression strength increased linearly with the increase in the cement content and exponentially with the reduction in porosity of the compacted mixture. The change in moisture content also has a marked effect on the unconfined compression strength of mixtures compacted at the same dry density. It was shown that, for the soil-cement mixture in an unsaturated state (which is usual for compacted fills), the water/cement ratio is not a good parameter for the assessment of unconfined compression strength. In contrast, the voids/cement ratio, defined as the ratio between the porosity of the compacted mixture and the volumetric cement content, is demonstrated to be the most appropriate parameter to assess the unconfined compression strength of the soil-cement mixture studied. [ABSTRACT FROM AUTHOR]

LRFD shows promise as a viable alternative to the present working stress design (WSD) approach to shallow foundation design. The key improvements of LRFD over the traditional WSD are the ability to provide a more consistent level of reliability and the possibility of accounting for load and resistance uncertainties separately. For LRFD to gain acceptance in geotechnical engineering, a framework for the objective assessment of resistance factors is needed. Such a framework, based on reliability analysis, is proposed in this paper. Probability density functions (PDFs), representing design variable uncertainties, are required for analysis. A systematic approach to the selection of PDFs is presented. A procedure such as that proposed provides a rational probabilistic basis for the development of LRFD methods in geotechnical engineering. [ABSTRACT FROM AUTHOR]

This paper presents an investigation of the dynamic response of foundations resting on a layered soil underlain by a rigid layer. Model block vibration test results are used for the investigation. For the analysis, two different methods, namely, the equivalent spring-mass-dashpot model and the cone model, are used. A simple method to estimate the equivalent stiffness of the foundations resting on any multilayered soil system is presented. Obtaining stiffness from the proposed method and using different values of the damping factor ranging between 1.5 and 10.0%, the dynamic response of a foundation resting on a layered soil system is computed. One-dimensional wave propagation in an elastic cone for the analysis of foundations resting on the elastic homogeneous half-space or layered soil is also used to compute dynamic responses of the foundations resting on different layered soil. Finally, results obtained from two analytical methods are compared with the test results. It has been observed from the comparison that the results obtained by the equivalent spring-mass-dashpot model with a damping factor of 1.5% matched well with the experimental results for all cases. Results obtained by the cone model match well with experimental results for the cases where the top layer is softer than the bottom layer. [ABSTRACT FROM AUTHOR]

Carbonatic rocks are subject to progressive degradation of their mechanical characteristics due to weathering. This phenomenon may have relevance for engineering since it can induce settlement of foundations, progressive failure of slopes or an increase of pressure on tunnel liners. To study weathering effects on a laboratory timescale, oedometric tests have been conducted on specimens of calcarenite and artificially cemented silica sand. Weathering was simulated by percolating an acid solution. Under constant load, the recorded progression of deformation over time ends with a horizontal asymptote when only bonds are destroyed (cemented sand), whereas it results in a steady increase when the grains are also degraded (calcarenite). To determine the variation in stress state induced by weathering, a special oedometer was designed. Allowing very small lateral deformation of the ring, its circumferential stretching was measured with strain gauges and correlated to the lateral pressure exerted by the specimen. In all cases considered, the horizontal stress increased remarkably during weathering at constant vertical load. Predictions of a chemoplastic constitutive model are then compared to experimental data, and then show good agreement, especially for cemented sand. [ABSTRACT FROM AUTHOR]

In this Technical Note, the adaptive block element method of rock masses is formulated, in which the elastoplastic characteristics of both rock blocks and discontinuities are taken into account. The concept of an overlay element is illustrated first; then the displacement fields of rock blocks are expressed as functions of so-called general degree of freedoms using the shape functions of the hierarchical finite element method; the governing equations of the rock block system are deduced on the basis of the virtual work principle; and the p-version adaptive algorithm based on the energy norm error estimation of each block element is proposed. The method is applied to the deformation and stability study of a gravity dam, and the parallel laboratory physical test is used to check the validity and ability of the method. [ABSTRACT FROM AUTHOR]

This paper presents a detailed investigation of the influence on the rocking impedance of flexible sidewalls in embedded foundations. The study focuses on vertical and cylindrical foundations embedded in a homogeneous elastic stratum. In order to anticipate the effects of the flexibility, closed-form formulae for rocking impedance are derived based on three-dimensional wave propagation theory and superposition of both the rocking and flexural movements on a single model by assuming complete bonding conditions between the soil and foundations. A function representing the effect of the flexibility is identified from the closed-form formulae, in terms of the height to radius ratio of the foundations and the ratio of the stiffnesses of the ground and foundations. The rocking impedance for a flexible sidewall differs from those evaluated under the assumption of a rigid sidewall. The applicable range of rocking impedance evaluated under the assumption of a rigid sidewall is assessed, and contours to assist in the estimation of the dynamic response of deeply embedded foundations are presented. [ABSTRACT FROM AUTHOR]

With reference to the classical geotechnical problem of predicting footing settlement in cohesionless soil, authors presented a method aiming at managing the uncertainty associated with lack of computational methods well founded on sound mechanical models. To this end, an artificial neural network was built in order to learn the relationship between input and output variables, from a large body of examples. Predictions comply with data more favorably than existing methods thus, broadening the field of application of knowledge-based systems in geotechnical engineering.

The article presents information on a study on the settlement ratio of pile groups in sandy soils from field load tests. It informs that from an analysis of loading tests on more than 30 pile groups it was found that the mean value of settlement ratio decreases as the average load per pile in the group increases. It is stated that the stiffness factor for aluminum pipe piles is an order of magnitude less than for the groups of solid reinforced concrete piles and steel pipe piles. It is maintained that in foundation engineering practice, piles are usually much longer, stiffer, and have greater failure loads than is the case for many of the piles in the study.

The article presents the author's comments about the article "Estimation of Bearing Capacity of Circular Footings on Sands Based on Cone Penetration Test," by Junhwan Lee and Rodrigo Salgado, published in the April 2005 issue of the journal. The author says that Lee and Salgado have contributed a lot to the study of shallow foundations. He agrees with their statement that serviceability and ultimate limit states should be treated within the same framework in case of geotechnical engineering.

The article discusses the study involving high-modulus columns for liquefaction mitigation. The authors resort to the Chinese criteria to support their argument of liquefaction and emphasize the similarity of ML/CL soils of the site to those encountered in Adapazari, Turkey which were presumed to have liquefied during the Kocaeli earthquake on the basis of observed displacements of building foundations. The authors compared performance of the supermarket building area which was strengthened through construction of jet-grout columns.

This article comments on the subject of centrifuge model study of laterally loaded pile groups in clay. The authors leave out a few points that could have made the results clearer to a reader, such as comments on the potential influence of the boundary conditions. With regard to the shadowing effect expressed by the authors in the p-multiplier approach, there became a reminder on a certain recommendation to allow only for resistance from the lead row plus side-row piles and to disregard the inside piles.