Search

This work reports the fabrication of mesoporous silica films with controllable wall thicknesses by spin coating of precursor solutions consisting of polystyrene-block-polybutadiene-block-polystyrene based triblock copolymers (Hydrogenated methyl Styrene Ethylene Butadiene methyl Styrene, HmSEBmS) and tetraethyl orthosilicate (TEOS) followed by calcination in air at 600 °C, for optical anti-reflection films. By changing the relative weight of the triblock polymer to TEOS, the pore-to-pore distance in the mesoporous silica film can be controlled without significantly affecting the size of the mesopores, thus, enabling effective control of the refractive index and porosity of the films. In terms of optical properties, the transmittance of the fabricated mesoporous silica film is approximately 3.3% higher than that of the uncoated glass substrate in the wavelength range of 400 to 750 nm.

CuS nanostructured materials, including nanoflakes, microspheres composed of nanoflakes, microflowers, and nanowires have been selectively synthesized by a facile hydrothermal method using CuSO4 and thiourea as precursors under different conditions. The morphology of CuS particles were affected by the following synthetic parameters: temperature, time, surfactant, pH value, solvent, and concentration of the two precursors. The synthesized CuS nanomaterials were characterized by X-ray diffraction, Brunauer-Emmett-Teller N2 adsorption, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. The electrochemical tests, including constant current charge-discharge and cyclic voltammetry, show the specific capacities of the different morphologies, as well as their rate capability. The nanowire electrode has near theoretical specific capacity and the best rate capability.

The structural evolution of nanocrystalline TiO2 was studied by X-ray diffraction (XRD) and the Rietveld refinement method (RRM). TiO2 powders were prepared by the sol-gel technique. Post annealing of as-synthesized powders in the temperature range from 500 degrees C to 800 degrees C under air and argon atmospheres led to the formation of TiO2 nanoparticles with mean crystallite size in the range of 37-165 nm, based on the Rietveld refinement results. It was found that the phase structure, composition, and crystallite size of the resulting particles were dependent on not only the annealing temperature, but also the annealing atmosphere. Rietveld refinement of the XRD data showed that annealing the powders under argon atmosphere promoted the polymorphic phase transformation from anatase to rutile. Field emission scanning electron microscopy (FESEM) was employed to investigate the morphology and size of the annealed powders.

Copper oxide-carbon composite with hollow sphere structure has been synthesized by a one-step spray pyrolysis method and tested as anode material for lithium-ion batteries. Different analytical methods, including X-ray powder diffraction, scanning electron microscopy, energy-dispersive X-ray spectrometry, thermogravimetric analysis, and systematic electrochemical tests were performed. The results demonstrate that the CuO-carbon composite in conjunction with carboxymethyl cellulose (CMC) binder has an excellent electrochemical performance, with a capacity of 577 mAh g(-1) up to 100 cycles. The usage of the water soluble binder, CMC, not only obviously improves the electrochemical performance, but also makes the electrode fabrication process much easier and more environmentally friendly.

Iron doped CeO2 nanoparticles with doping concentrations between 0 and 30 mol% were synthesized by the co-precipitation method for potential application as a pigmented ultraviolet filtration material. Each sample was calcined in air and in argon. The iron solubility limit in the CeO2 lattice was found to be between 10 and 20 mol%. Raman spectroscopy results revealed that both iron doping and argon calcination increase the concentration of oxygen vacancies in the CeO2 lattice. Iron doping causes a blue-shift of the absorbance spectrum, which can be linked to the decreased crystallite size, as obtained by XRD peak broadening using the Scherrer formula. The undoped samples showed weak ferromagnetic behaviour whereas the doped samples were all paramagnetic.

Hematite nanoparticles were synthesized for ultraviolet filtration application by the precipitation method followed by calcination at different temperatures. A range of crystallite sizes between 37 and 85 nm (as determined by the Scherrer formula) was obtained, according to the temperature used for the calcination. An increase in the absorbance with increasing crystallite size was observed over the whole ultraviolet B and A range. The experimental band gap was 2.94 eV for the sample calcined at 500 degrees C and 3.08 eV for the sample calcined at 300 degrees C. The in vitro sun protection factor and protection factor-ultraviolet A of a water-in-oil emulsion made with the sample calcined at 500 degrees C as active ingredient were 9.21 and 8.81, respectively, which is higher than the protection factor-ultraviolet A values obtained for titanium dioxide and zinc oxide at the same mass concentration. The emulsion was found to be photostable.

In this study, nanostructured transition metal oxides, such as Co3O4, NiO and MnO2 were comprehensively studied and reported as promising electrode materials for electrochemical capacitors. The materials have been obtained by solution or spray solution techniques, which are cost-effective and promising for industry application. All materials feature a large specific surface area, which can reach up to 270 m2/g. The high surface area is a compulsory condition for high capacitance. The best MnO2 materials yielded up to 406 F/g.

In lithium-ion batteries, nanocrystalline intermetallic alloys, nanosized composite materials, carbon nanotubes, and nanosized transition-metal oxides are all promising new anode materials, while nanosized LiCoO2, LiFePO4, LiMn2O4, and LiMn2O4 show higher capacity and better cycle life as cathode materials than their usual larger-particle equivalents. The addition of nanosized metal-oxide powders to polymer electrolyte improves the performance of the polymer electrolyte for all solid-state lithium rechargeable batteries. To meet the challenge of global warming, a new generation of lithium rechargeable batteries with excellent safety, reliability, and cycling life is needed, i.e., not only for applications in consumer electronics, but especially for clean energy storage and for use in hybrid electric vehicles and aerospace. Nanomaterials and nanotechnologies can lead to a new generation of lithium secondary batteries. The aim of this paper is to review the recent developments on nanomaterials and nanotechniques used for anode, cathode, and electrolyte materials, the impact of nanomaterials on the performance of lithium batteries, and the modes of action of the nanomaterials in lithium rechargeable batteries.