Search

Biodegradable plastics are thought to be the possible directions in managing plastic pollutions. Unfortunately, they are not recycled in most countries since they are designed to decompose even though recycling is a more pragmatic method than landfill or incineration. Thus, it is more constructive to develop methods to recycle biodegradable plastics or to develop biodegradable yet recyclable plastics. In this study, we used cutlery with a composite of poly(lactic acid) (PLA) and talc. The possibility to recycle it to make foams was studied even though it will have lowered mechanical strength from the recycling process as it is less significant for this product. Tensile properties of solid PLA and foams showed no significant decrease in the strength up to three processes of compression molding and foaming. We performed shear rheometry to determine the thermal stability and dependences of the complex viscosity on frequency and temperature. The magnitude of the complex viscosity dramatically increased with decreasing frequency and such an upturn increased with temperature, but time-temperature superposition was valid at high temperatures. The extensional rheometry showed no strain hardening, but physical foaming using supercritical carbon dioxide (CO2) could still occur, and the operating conditions to obtain various foamed structures were determined. We also compared the effects of one-directional against three-dimensional expansion. Overall, the concentration of CO2 in PLA and crystallinity of the foams are the two key variables to describe the bulkiness of foams. Surprisingly, the lower the CO2 concentration, the bulkier the foams at any sorption temperature and pressure. [ABSTRACT FROM AUTHOR]

Hydrogels with or without chemical cross-linking have been studied and used for biomedical applications, such as tissue repair, surgical sealants, and three dimensional biofabrication. These materials often undergo a physical sol–gel or gel–sol transition between room and body temperatures and can also be chemically cross-linked at these temperatures to give dimensional stability. However, few studies have clearly shown the effect of heating/cooling rates on such transitions. Moreover, only a little is known about the effect of cross-linking temperature or the state on the modulus after cross-linking. We have established rheological methods to study these effects, an approach to determine transition temperatures, and a method to prevent sample drying during measurements. All the rheological measurements were performed minimizing the normal stress build-up to compensate for the shrinking and expansion due to temperature and phase changes. We chemically modified gelatin to give gelatin methacryloyl and determined the degree of methacryloylation by proton nuclear magnetic resonance. Using the gelatin methacryloyl as an example, we have found that the gel state or lower temperature can give more rigid gelatin-based polymers by cross-linking under visible light than the sol state or higher temperature. These methods and results can guide researchers to perform appropriate studies on material design and map applications, such as the optimal operating temperature of hydrogels for biomedical applications. We have also found that gelation temperatures strongly depend on the cooling rate, while solation temperatures are independent of the heating rate. [ABSTRACT FROM AUTHOR]

Two tube-based molecular models, the hierarchical 3.0 model and the branch-on-branch model were evaluated for their abilities to predict the behavior of a series of polydisperse, H-shaped, 1,4-polybutadienes. The samples had been synthesized using a novel technique designed to suppress the generation of high molar mass by-products. While size exclusion chromatography data indicated that the samples were monodisperse, low molar mass by-products were later revealed by temperature gradient interaction chromatography. Viscoelastic data were obtained at temperatures ranging from -75 °C to 25 °C, and the samples were found to be thermorheologically simple. Sensitivity and uncertainty analyses revealed that among the model parameters, the value of plateau modulus has the strongest effect on model predictions. As molecular models improve, it will become ever more essential to evaluate them using accurate data on materials whose microstructures have been reliably established. This is especially important for materials that are structurally polydisperse. [ABSTRACT FROM AUTHOR]

We studied polymer-polymer interfacial slip in bilayer films of highly immiscible (interaction parameter, χ≅0.1) polyethylene and fluoropolymer from medium to higher shear stresses (10-200 kPa) using both visualization and stress reduction. We found good agreement between results from the two methods as well as with previous studies using multilayers by Lee et al. [J. Rheol. 53, 893-915 (2009)] and visualization of flow in a transparent capillary by Migler et al. [J. Rheol. 45, 565-581 (2001)]. We observed two power-law regions: Vslip∝τ6.2 with a transition to Vslip∝τ1.8 at 50 kPa. This is in contrast to the theory of Brochard-Wyart and de Gennes [C. R. Acad. Sci., Ser. II: Mec., Phys., Chim., Sci. Terre Univers 317, 13-17 (1993)], which predicts a transition from infinite slope to a slope of one at a critical stress. [ABSTRACT FROM AUTHOR]

Publisher's Note: "Recycling and rheology of poly(lactic acid) (PLA) to make foams using supercritical fluid" [Phys. Comparison of the top view of the cell structure after cutting samples in the direction that is parallel to the bottom surface [Fig. This article was originally published online on 29 June 2021 with an error in the captions for Figs. [Extracted from the article]